USER MANUAL
Contents
1. gt k PA4 200 PA4 200 DSP USER MANUAL NGG 4 CHANNEL PA SYSTEM 27 Universe of Mosse 9 ESN o EXIT 043 S Si sb AL O NI DIN ESE EEN man sk Sb oo ES su sb GE sb O 6 gt 9 9 Em s sb 69 69 69 69 69 69 C9 9 69 5 5 5 5 5 5 5 v 1ANNVHO 1ANNVHI PA4 200 6 PA4 200 DSP USER MANUAL FRONT PANEL This PA System includes a 4 Channel 2x75 W RMS 4 Ohms Powered Mixer w Digital Reverb PA4 200 or w Digital Signal Processor PA4 200 DSP and two 2 way 150W 4 Ohms Speaker Cabinets INPUT SECTION FEATURES CHANNEL 1 to 4 1 MIC IN This low impedance 3 pin XLR input socket is for connecting balanced low impedance microphones Input impedance is 1k Ohm The connector is wired as Pin 1 shield Pin 2 positive hot Pin 3 negative cold 2 LINE This high impedance line level 1 4 jack input socket may be used either with high impedance microphones or with devices such as Tape CD MP3 players effect returns or radi2. This controls the overall level of any CD or Tape player connected to the apparatus via the CD Tape inputs on the rear panel 3 EFF RETURN This controls the signal output level of the internal effect Digital Reverb on PA4 200 and Digital Sound Processor on PA4 200 DSP mixed to the direct signal coming from the master EQ output 4 MASTER This is the master volume which controls the overall volume level of the unit 5 DSP EFFECT PA4 200 DSP only This selector enables the user to choose among 16 internal DSP effects including 8 Reverb effects 3 x Chorus 1 x Flanger 2 x Delay 1 x Vocal Mute amp 1 x Rotating speaker effect 6 EFF SEND PA4 200 DSP only This controls the amount of the output signal from the internal DSP effect 7 POWER LED PA4 200 DSP only When this red LED is lit the powered mixer is ready to work When it is unlit it means the apparatus is powered off PA4 200 amp PA4 200 DSP 3 USER MANUAL 4001 193443 AdvL 09 EL ga 193185 PA4 200 6 PA4 200 DSP USER MANUAL BACK PANEL WARNING This device must be earthed Please check that the supply voltage details given on the rating label located on the rear panel are in accord
3. ance with your electricity supply 1 POWER This switch turns the powered mixer on or off The switch is illuminated when the device is powered on On PA4 200 models this switch is located on the FRONT PANEL 2 MAINS This is the input socket into which the mains power cable must be connected This powered mixer is supplied with a power cable with a moulded on plug If the socket outlets in the home are not suitable for the plug supplied with this device use an appropriate plug adapter that can handle the power required for this powered mixer 3 FUSE In the event of the power fuse having to be replaced first unplug the power cable from the mains outlet Then remove the fuse cover and replace the power fuse with one of the same type and value Never plug the power cable back into the mains outlet without the fuse cover If when powering on the device the power fuse blows up again go to a suitable service centre for repair 4 VOLTAGE SELECT This switch selects the chosen voltage level between 120VAC and 230VAC as appropriate This switch may be accessed by unscrewing the safety cover Always make sure that the selected voltage level is in accordance with your electricity supply 5 CD TAPE IN These are two line level Phono Cinch inputs into which a CD Tape MP3 player may be connected Please note that both L and R inputs must be used in order for the sound to be reproduced in full 6 EFFECT SEND This PA system is equipped with an effe
4. ck the available mains voltage 120VAC or 230 VAC If necessary change power voltage on your device with the Voltage Selector see n 4 page 5 Plug the mains lead into a suitable power socket see n 2 page 5 Connect your speaker cabinets a to the output speaker sockets at the rear panel see n 8 page 5 with the 10 meter speaker cables supplied Make sure that the master volume is set to zero before powering on the amplifier to avoid possible damage to the speakers Finally set the MASTER volume to zero and push the Power Switch to the ON position The power switch will light up and your PA system is ready for use Should you experience any feedback coming from the speakers first diminish the volume of each channel in use in order to find amp suppress the microphone causing the feedback Then reposition this microphone preferably somewhere behind the speakers and reset the channel volume accordingly IMPORTANT SAFETY INSTRUCTIONS READ AND KEEP THESE INSTRUCTIONS HEED ALL WARNING If after you have followed the instructions outlined above the powered mixer fails to function please contact your vendor Under no circumstances should the unit be opened Leave servicing to qualified personnel only Electrical appliances must never be used in conditions of high humidity or heat To prevent any risk of electric shock or fire never spill or splash liquids on the unit Should this happen unplug the power cable from the mains outle
5. cts loop which allows you to plug outboard effects or EQ systems between the preamp and the power amp The SEND jack is a line level 1 4 9 6 3 mm output jack into which you may connect one or several outboard effects eg Flanger Compressor Pitch shift Chorus etc The SEND jack should be connected to the input jack of the first effect in your effects chain 7 EFFECT RETURN This is a line level input jack to which you should connect the output jack of the last effect in your effects chain The effects loop may also be used with a multi effects rack system or with a single effect 8 SPEAKER OUT 1 amp 2 These are 4 Ohm 1 4 output jacks into which you may connect the two speaker cabinets included in the set or any two speaker cabinets w a minimum impedance of 4 Ohms and a minimum power handling of 120 W RMS PER SPEAKER PA4 200 amp PA4 200 DSP 5 USER MANUAL TECHNICAL SPECIFICATIONS PA4 200 or PA4 200 DSP POWERED MIXER Output Power 2x75WRNS 4 Ohms Input Impedance Input Channel EQ 15 dB 50 Hz i 15 dB 10 kHz 1548 50 Ha 12 4B 2 kh 15 dB 10 Wi 115V 60Hz 230V 50 Hz 120 x 480 x 260 mm 4 7 x 18 9 x 10 2 in Weight 8 66 kg 19 09 Ibs SPEAKER CABINETS 1x 10 150 W RMS 4 Ohms Speaker 1x Piezo Horn Tweete Dwegm serans Features and Specifications are subject to change without notice USER MANUAL 6 PA4 200 6 PA4 200 DSP INSTRUCTIONS FOR USE First che
6. os You may also connect an electric guitar bass or keyboard This is a 2 conductor input with an impedance of 10k Ohms Both high amp low impedance inputs may be used simultaneously 3 VOLUME This is the independent volume control for each channel The signal is sent to the master section Typical setting is between 4 and 8 depending on the channel s function Please note that this volume control acts as a preamp so if the channel is being used for a device that has a volume output control e g CD or Tape player some level matching by adjusting the level controls on each unit will be required 4 TREBLE This is the independent treble control to adjust the level of high frequencies in the output signal on both inputs of each channel 5 BASS This is the independent bass control to adjust the level of low frequencies in the output signal on both inputs of each channel 6 EFF This control is used to set the level of the internal effect Digital Reverb on PA4 200 and Digital Sound Processor on PA4 200 DSP blended in to the input signals of each channel MASTER SECTION FEATURES 1 EQUALIZATION BASS This controls the overall amount of low frequencies 50 Hz allowing 15 dB of boost or cut MIDDLE This controls the overall amount of middle frequencies 2 kHz allowing 12 dB of boost cut TREBLE This controls the overall amount of high frequencies 10 kHz allowing 15 dB of boost or cut 2 CD TAPE
7. t immediately Your attention is drawn to the instructions printed on the notice attached to the back of the unit CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN NG ro neouce THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT EXPOSE e Exposure to extremely high noise levels may cause permanent damage to hearing Use this apparatus responsibly for you and your neighbourhood MARKING 5 CONFORMITY 1 The CE mark on this product means it conforms to the EMC Directive 89 69 EEC CE marking Directive 93 68 EEC and Low Voltage Directive 72 23 EEC 2 The Crossed out Wheeled Bin is to draw your attention on the WEEE Waste Electric amp Electronic Equipment Directive 2002 96 EC It means this apparatus must be collected separately for recycling 3 RoHS compliant means this device conforms to the Directive 2002 95EC on the restriction of the use of certain hazardous substances in electrical and electronic equipments such as Mercury Lead Cadmium Hexavalent Chromium Polybrominated and Polybrominated Diphenyl Esthers PBDE cec X EE PA4 200 amp PA4 200 DSP 7 USER MANUAL DISTRIBUTOR DEALER staggmusic com EMD Graphics 06 2006
Download Pdf Manuals
Related Search