User Manual Digital Wireless Rain Gauge
Contents
1. In such conditions you must reset and re sync both the indoor monitor amp outdoor rain gauge If to do so please follow the Getting Started Power reset procedure NOTE After reset both the indoor monitor amp outdoor rain gauge if you find any data show on the indoor rain monitor display it may a wrong counting during place the batteries on the outdoor rain gauge please press the RESET button for 1 second to clear the display and start from 00 00IN or 000 0MM counting Warning Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient2. or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Tested to comply with FCC standards for home or office use Model Name Digital Wireless Rain Gauge Model Number 00896 The responsible party information Chaney Instrument Co 965 S Wells Street Lake Geneva WI 53147 Tel 262 248 4449 LIMITED WARRANTY INTERNATIONAL Consumer may have more remedies at law than follows Chaney Instrument Company warrants to the owner this product to be free from defect in material and workmanship for one year from date of purchase CHANEY INSTRUMENT SHALL NOT BE LIABLE FOR ANY INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES WHETHER ARISING IN CONTRACT OR TORT Chaney Instrument s obligation at its option is limited to repair or replace this product For in warranty repair send clock accompanied by Guarantee bearing Dealer s name and date of purchase with 5 00 to cover handling and postage to Chaney Instrument Company 965 Wells Street La
3. User Manual Digital Wireless Rain Gauge Rain Gauge Specifications Outdoor rain gauge transmitter measures the rainfall and transmits the data to an indoor rain monitor base unit which shows the rainfall information on the LCD display The display shows on of 3 available rain modes No rain Light rain Heavy rain Range of rainfall measurement on the LCD display o IN inch 00 00 99 90 o MM millimeter 000 0 999 9 Rainfall measurement can register accumulation up to o 99 90IN under inch display mode o 999 9MM under millimeter display mode Transmission range is up to 100 feet in an open area without interference Interference from such things as metal siding or wall studs and security systems can reduce the effective transmission range Power requirement o Indoor rain monitor requires 2 AAA alkaline batteries not included o Outdoor rain gauge transmitter 2 AA alkaline batteries not included Important Information 1 For the initial set up put the batteries in the indoor rain monitor base unit first and then into the outdoor rain gauge transmitter 2 For the outdoor rain gauge transmitter please make sure the counting lever inside the unit is placed in an upright position and is free to swing smoothly 3 For the best reception and to avoid the outdoor rain gauge being immersed in water while it is raining please place the outdoor rain gauge on a flat surfac
4. ation successful During the synchronization period press any key to stop the synchronization procedure Rainfall Alert Mode description To activate the rain alert mode slide the Alarm switch to the On position A beep alarm will sound for 10 seconds when the rain mode is changing Rain mode alert description o No Rain Average rainfall less than 0 02IN 0 05MM on the past few minutes o Light Rain Average rainfall between 0 02IN 0 5MM to 0 18IN 4 6MM on the past few minutes o Heavy rain Average rainfall equal or over 0 2IN 5 1MM on the past few minutes To turn off an alert mode slide an Alarm switch to Off position Data Transmission The display will read the following based on the data being transmitted from the rain collector No Rain If the last rain mode was No rain and a No rain mode condition for the past 5 minutes Light Rain If the last rain mode was Light rain and a Light rain mode condition was maintained for the past 3 minutes Heavy Rain If the latest rain mode was Heavy rain and a Heavy rain mode condition was maintained for the past minute Low battery indicator and battery changing If you see that the low battery indicator s has changed to half full status please install fresh batteries as follows Indoor rain monitor Remove the old batteries from the battery compartment and insert 2 fresh AA alkaline batteries Unit wil
5. e above ground level 4 Do not store or locate the outdoor rain gauge and a counting lever close to any source of magnetic interference or electrical equipment USING MANUAL Know Your Product Outdoor Rain Gauge Transmitter Measures the rainfall using the internal counting lever and transmits rainfall amp rain mode information to the indoor rain monitor base unit Lever resolution each lever swing 0 02 inch 0 508 millimeter Low battery condition will be detected and displayed on the indoor rain monitor Indoor Rain Monitor LCD display o 4 digit display for rainfall measurement IN inch 00 00 99 90 MM millimeter 000 0 999 9 o IN MM indicator o 3 rain mode indicators No rain Light rain Heavy rain o Antenna wave icon to show synchronization and connection status o Low battery indicators for outdoor rain gauge and indoor rain monitor Function keys o Reset key Press the Reset key for 1 second to clear all information on the LCD display The rainfall data can be reset at any time If not reset the display will show the total of all rainfall since the unit was activated or until the maximum allowable display is reached To monitor rainfall in a given time period it will be necessary to reset the unit at the start of the time you wish to measure o IN MM Inch Millimeter selection key Press the selection key for 2 seconds to view a rain
6. fall measurement in IN or MM display format o Light key Press the Light key the backlight will be turned on for 5 seconds o Alarm On Off switch located on back of unit To turn on the rain alert function slide the Alarm switch to On position To turn off the rain alert function slide the Alarm switch to Off position Before Getting Start Getting Started Power reset procedure 1 Please make sure batteries are inserted into the indoor rain monitor first and the display appears The unit will go into sync mode for 6 minutes 2 Insert batteries in the outdoor rain gauge transmitter 3 In the sync mode the indoor rain monitor will receive the outdoor transmission signal within 6 minutes 4 At the synchronization period the antenna wave icon will keep blinking on the rain monitor display 5 When the antenna wave icon stops blinking and remains on the display this means synchronization has occurred and the main unit has gotten the signal from the transmitter unit 6 Once the synchronization has occurred the indoor rain monitor will detect updated rainfall information from the transmitter every minute automatically 7 If the antenna wave icon does not appear on the display after the 6 minutes synchronization period it means synchronization has failed 8 Indoor rain monitor will start synchronization again after 2 minutes until synchroniz
7. ke Geneva Wisconsin 53147
8. l sync with the outdoor transmitter unit automatically NOTE After battery replacement if you find any data showing on the indoor rain monitor display it must be accumulated data Please press the RESET button for 1 second to clear the display and start counting from 00 00IN or 000 0MM Outdoor rain gauge To change the outdoor rain gauge batteries you must press and hold the RESET button for 5 seconds on the indoor rain monitor and let it re sync again NOTE After battery replacement if you find any data show on the indoor rain monitor display it may an incorrect counting the occurred during the battery change Please press the RESET button for 1 second to clear the display and start counting from 00 00IN or 000 0MM ERR signal occurred on rain monitor display When the indoor rain monitor notes an accumulative data out of the display range Maximum inch data is 99 90IN and millimeter data is 999 9MM the unit will show ERR signal on the display and sound for 1 minute Press any key to clear ERR signal and start from 00 00IN or 000 0MM counting Resetting the outdoor rain gauge and troubleshooting The outdoor rain gauge is using a data accumulation method to transmit information to the indoor rain monitor If it is necessary to erase an accumulated data on the outdoor rain gauge OR In some unusual occasions the unit may be affected by electrical interference and respond abnormally or ERR signal occurred
Download Pdf Manuals
Related Search