ITA3D 710 RGB DMX laser with 3D effect User manual - Bax
Contents
1. ASIP ITA3D 710 RGB DMX laser with 3D effect Sho SSS _ gt AJRA ITASD 710 User manual Safety precautions WARNING This unit may cause serious injury to eyesight when used incorrect It therefore is strongly advised to read this user manual carefully to get familiar with the functions of this laser device WARNING This unit must be operated by or under the supervision of an adult This device is not suitable for children WARNING Do not look directly into the beam coming out of the lens from short distance or when a solid beam is projected This may cause serious injury to eyesight Ayra is not responsible for any injuries caused by incorrect use of this device WARNING Do not project the beam of this unit on to reflective surfaces as the shattering beam may cause injury to eyesight Installation requirements Always check the voltage settings on the unit and the power supply you want to connect the device to If the voltage requirements do not meet do not connect the device as this may cause serious damage This device must be installed by a professional technician in a standing or hanging position Always pay attention to the positioning of the unit as the beams may project directly into your audience It is strongly advised to NOT project the beams directly into your audience Ayra strongly recommends a minimum distance of 1 5 meters in height between the lowest projected laser beam and your aud2. WITCH CHART FUNCTION 1 2 3 4 5 6 7 8 9 10 0 0 0 xX xX xX xX xy x 0 SOUND ACTIVE 1 0 0 xX xX x x x x 0 AUTO BEAM 1 1 O0 xX xX xX xX x xX 0 AUTO ANIMATION O0o oO 1 x xX xX xX xX x 0 SLAVE MODE SET DMX ADDRESS 1 DMX MODE Working mode explanation Sound active The unit uses its internal microphone to sense music the beat of the music and will change patterns according to the beat of the music The microphone is situated at the front of the laser device On the rear of the laser there is an adjustable microphone sensitivity knob Please note that the sound activated mode will not function properly when the music source is not loud enough or when only high pitched sounds are played Auto beam The laser device will activate a pre defined lasershow on a solid speed setting The patterns are mainly beam effects Auto animation The laser device will activate a pre defined lasershow on a solid speed setting The patterns are mainly animations and graphics Slave mode It is possible to link several ITA3D 710 fixtures for a synchronized lasershow without the use of a DMX controller Connect your devices with standard XLR XLR cables The first device in the chain needs to be set to a basic function such_as sound active or one of the auto shows Select the slave mode on all other connected device in the chain You will notice that these devices will mimic the actio
3. d DMX automatic or music controlled mode It is possible that the unit may shut off the beam projection when no music or sound is detected This will avoid the projection of a solid static beam which may cause injury to eyesight This unit uses stepping motors to create variable movements to the laser beam This way figures and patterns can be made The unit uses high speed stepping motors to create the moving beams of the laser It is normal that the laser beam and projection may appear flickering when projecting large or complex patterns The projected beams of the unit may appear shivering when projecting complex or large patterns on surfaces as a wall ceiling or decorative cloth Selecting a working mode This laser device has three working modes which are automatic music controlled and DMX To select the right operating mode for your situation use the dipswitch panel on the rear of the unit A DMxX dipswitch panel works with a binary character It sends a 0 or 1 message to the electrical circuit To select a working mode pay close attention to the information scheduled below Every DMX dipswitch stands for a certain value which is on or off The values are stated as below 9 256 10 mode switch DMX ON OFF To select the different working modes pay close attention to the setting of DMX dipswitches below NOTE value X not used or not active for this mode DIPS
4. d for a longer period of time disconnect it from the power supply and store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any laser beams do not look directly into the lens When the laser suddenly produces a beam it may cause severe eye damage possibly resulting in permanent visual loss Device overview OrowerO Mc visible or invisible radi ation avoid eye or skin exposure to direct or scattered radiation FUNCTION SETTING DMX Linking o0 1 Ground DMX dipswitch setting also used for activation of auto sound active mode Microphone sensitivity knob low high 9 Pattern size adjustment small large 10 Cooling fan 11 IEC power inlet 12 ON OFF switch 1 Beam output 2 Power status LED indicator red 3 Microphone sensitivity LED indicator blue 4 Built in microphone used for sound active mode 5 DMX input 6 DMX output 7 8 Setting up the device Setting up the device When the power supply is connected the unit will first calibrate the stepping motors of the unit It is normal that this may cause any noise When the calibration is done the unit is ready to be used in the selecte
5. eaning the unit Reconnect the unit only if any moist on the fixture disappeared completely This laser device is a lighting effect designed to support visual entertainment while playing music Continuous use is not recommended Do not use the device longer than 3 hours subsequently so the unit can cool down This will provide a longer lifespan for the diodes Apply a cooling down time of 25 minutes before re activating the laser Do not switch the power on and off too often as this may cause serious damage to the unit Avoid heavy shocks and collision during transport and use as this might cause damage to the laser diodes electronic circuit optics and housing Keep the device away from moisture rain water or any liquids as this may cause a short circuit and or electric shocks If any liquid enters the unit power supply or housing of the unit disconnect the unit immediately and do not reconnect the power supply Contact your local dealer or technician to inspect the unit for any damage Box contents Box contents 1x ITA3D 710 laser device 1x user manual 1x IEC to Schuko power cable 1x XLR XLR DMX signal cable Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears broken or has visible damage do not use it The supplied cable can be replaced with a regular IEC to Schuko cable with a minimum cable diameter of 0 75m2 If the unit will not be use
6. ience for optimal safety If there is no other option keep a minimum distance of 5 meters from the beam exit to the first beam that hits your audience When installed in a standing position a safety cable is recommended to secure the unit When installed in a hanging position this unit MUST be secured by using a safety cable capable of holding 10x the weight of this device When installed in a hanging position this unit must be mounted to a proper surface e g a truss system When using a truss system Ayra recommends the use of a proper hook or halfcoupler Make sure there are no flammable objects in the direct environment of the device Such as decorative objects Keep a minimum distance of 1 5 meter Do not block the beam exit and fan Keep a minimum distance of 0 5 meter from any walls to provide sufficient cooling Make sure the beam exit and fan are not blocked by any objects in the near environment This unit must be connected to a grounded power supply that meets the voltage requirements of the device Maintenance and protection Keep the unit away from dusty environments as this may have negative effect on the fan cooling system and laser optics Ayra recommends using a flightcase for storage of this device Clean the optics and fan of the laser with a small soft brush and vacuum cleaner when needed Clean the housing of the unit with a damp cloth WARNING Always disconnect the unit from the power supply when cl
7. ns of the first device DMX mode With an external DMX controller or DMX software it is possible to control every feature of the laser device It is possible to adjust the built in patterns and to add several effects such as zoom effects or pattern rotation NOTE When the DMX signal or master slave signal is lost due to a failure in the DMX connection or any other reason the laser will shut off the output due to safety issues This prevents the projection of static images and or patterns DMX operating mode While in the DMX mode it is possible to select the working mode of the laser That way you can either choose to use your own programmed presets of your DMX controller or to activate the music activated automatic working mode of the laser to have a fully automatic lasershow Depending on the starting address you selected earlier the laser responds to the following commands In this example we use DMX starting address 1 When you use a different DMX starting value for example 29 the unit will respond from channel 29 30 31 and so on For more information about DMX consult the manual of your DMX controller or software Channel Function Value Description 1 Mode 0 49 Sound active mode 50 99 Auto beam mode 100 149 Auto animation mode 150 199 Manual mode auto run 200 255 Manual mode sound active run 2 Color shutter 0 255 Closed
8. r truss system built in microphone with adjustable microphone sensitivity adjustable pattern size small large DMX control with 3 pin XLR connectors DMX control 12 channels Power supply 100 250V AC 50 60 Hz Power consumption 20 Watt dimensions 300 x 185 x 100 mm weight 2 5 kg
9. single color flashing color multi color and moving multicolor effects 3 Pattern 0 255 256 patterns to be selected selection 4 Movement Y 0 127 Manual up down movement 128 191 Auto down movement 192 255 Auto up movement 5 Movement X 0 127 Manual left right movement 128 191 Auto right movement 192 255 Auto left movement 6 Rolling X 0 127 Manual rolling position 128 255 Auto rolling movement 7 Rolling Y 0 127 Manual rolling position 128 255 Auto rolling movement 8 Rotation 0 127 Manual rotation position 128 191 Auto clockwise rotation movement 192 255 Auto counter clockwise rotation movement 9 Zoom 0 85 Auto zoom 86 170 Auto zoom 171 255 Manual zoom 10 Pattern size 0 255 0 is standard 1 255 is small to large 11 Display dot 0 255 Variable adjustment 0 is dot display 255 is best brightness 12 Drawing 0 127 Auto drawing mode 1 128 255 Auto drawing mode 2 Technical specifications TYPE ITA3D 710 Laser diodes Type ITA3D 710 60 mW green laser wavelength 532nm 150mW red laser wavelength 650nm 500mW blue laser wavelength 450nm Tech specs scanset 15 kpps high speed optical scanner with big angle capacities working modes auto sound active master slave DMX 512 graphics and effects 128 beam show and animated graphic show patterns with 3D animation high efficiency 3D optical grating system for unique 3D lighting effects hanging bracket for use with a lighting stand o
Download Pdf Manuals
Related Search