Jerome® Communications Software (JCS)
Contents
1. connector to the computer the DATA LOGGER connector to the Jerome Data Logger and the INSTRUMENT connector to the instrument Launch the JCS program on the PC If all preliminary set up procedures have been completed Turn the instrument ON Click on Data Logger Click on Program Enter the Sample Interval and Alarm Setpoint Click on Program Turn the instrument OFF Vv VVVWV Installed in Instrument DB25 Connector Installed in Data Logger Se Gee DB9 Connector installed in Computer Serial Port Disconnect the JCS Interface Cable from the instrument and from the Data Logger Connect the Data Logger directly onto the instrument When the instrument is at the location for sampling gt Turn the instrument ON gt Press the Sample Button on the instrument When sampling is complete gt Turn the instrument OFF gt Remove the Data Logger from the instrument gt Connect the JCS Interface Cable s PC connector to the PMODEL 431 5 an SERIAL NO 2336 mu t vac 50 50 HZ AMP 220 MADEIN USA POR SIEVICI Att Sin 470 1414 FOR SERVICE CALL HIGH MEMORY 1 800 235 3360 o 95 42 a ARIZONA INSTRUMENT E LEVEL FULL DATA LOGGER DATA ACQUISITION SYSTEM Ee Aki computer the DATA LOGGER connector to the Jerome Data Logger and the INSTRUMENT connector to the instrument Turn the instrument ON Click on Data Logger Click2. mode on all but one The software will be fully functional on the one computer that has the security key installed in a USB port The security key is installed after the software has been installed as detailed in the next section AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 9 of 24 As soon as the JCS software installation is complete insert the USB security key into an available USB port The computer will automatically detect the key and install drivers that were copied into the computer during the JCS installation The Data Logger and Instrument menu items are only available while the key 1s installed The key can be moved from computer to computer However only the computer in which it is installed will be capable of full program operation installed in FUSB Port Computers that have the software installed but no security key installed will operate in a demonstration mode only No data can be transferred to or from the instrument but data previously stored in the computer may be viewed F AZI Jerome Communications Software Click on Start gt Programs or All Programs gt pie setup Data Logger Data Instrument Window Help AZI gt JCS to launch JCS The screen shown to the right appears along with the help screen ry shown below The JCS program operates f A according to Windows conventions for menu Arizona Instrument driven programs Selections are made with a mouse pointing
3. 470 1414 800 528 7411 or support azic com Page 3 of 24 The Jerome Communications Software JCS operates with the J erome 431 X Mercury Vapor and J erome 631 X Hydrogen Sulfide Analyzers that have the Communications option installed The software can control instrument sampling for unattended continuous operation collect data graph this data in real time and perform statistical analysis The software can also program the Jerome Data Logger AZI P N 6100 0010 This optional accessory enables data storage during manual sampling or portable automatic sampling without being attached to a computer The Data Logger initiates automatic sampling triggers alarms and stores data The logged data may then be downloaded to the computer when it 1s convenient The JCS software is menu driven and easy to use Each display screen is designed for clarity with self explanatory menu options Select menu options using either a mouse pointing device or a standard keyboard The user creates records or files for computer storage of collected data Data is easily retrieved for later viewing graphing printing or editing with spreadsheet or word processing software not provided Data can be used for ongoing record keeping or for fulfilling local regulatory requirements Before using this software familiarization with the operation of the J erome Hydrogen Sulfide Analyzer or Mercury Vapor Analyzer is important Prior to installation of this softwar
4. Click on Data on the menu bar to view or export data records e Select the record you want to view or export from the list gt The address technician instrument and alarm setpoint and comment for the selected record are displayed to the right of the selection list F AZI Jerome Communications Software File Setup DataLogger Data Instrument Window Help El site And Location Address EJ MEEUSE AMERA Lec 21 200 0 2arn 1912 Water Blvd Phoenix A goood Technician Mr Brown a Instrument Jim s 631 631 4 SH 1004 Alarm setpoint Comment E AAA K Record 14 4 1 Lt gt of 1 Close View Report View Graph ExportReport A IN e Click on View Report or View Graph buttons display the data e To view the report e Click on the View Report Button e If an Alarm Setpoint was specified then click on either Yes or No to answer the question Display alarm readings only If you click on yes and there are no readings above the alarm setpoint the Insufficient test data to display message will be displayed e To exit from a report or graph press the ESC key on the computer s keyboard AZI Jerome Communications Software P j Display alarm readings only Page 16 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com A sample report is shown below Site Name Doc Control Address 1912 VV 4th Street Tempe Af 85201 DATE TIME Jan 20 2003 12 52 30 prn
5. Communications Software Choose Program Ea e Click on Continue to add the AZI Program Group and AZI icon to the Setup will add items t the group mer To 5 ter a new group name or select one from the Existing Groups list computer s Start Menu If desired type in a different program group or click on Cancel to prevent the addition of the Program Group AZI group to the Start Menu AZI Jerome Communications Software Existing Groups e The software may take several seconds er A to load depending on the speed of your computer and disk drive Lavasoft Ad aware Startup Webshots Desktop Windows Media Player Bonus Pack coca e If Microsoft Access 2000 database ES Access Install software SRI or later is installed on auni See ee tee your computer no additional software will be installed by JCS If Access 2000 database software SR1 or later is not installed on your computer then Access Runtime will be installed This screen will indicate what program was found and what action was taken NOTE When installed on Windows XP Windows 2000 or Windows NT operating systems the computer user must have read write access to the Program Files AZI JCS directory See your network administrator or the operating system help files for assistance in setting rights The software may be loaded on as many computers as desired but will operate in a demonstration
6. Jan 20 2003 1 07 29pm Jan 20 2003 1 22 29pm Jan 20 2003 1 24 29pm Jan 20 2003 1 39 29pm Jan 20 2003 1 54 29pm Jan 20 2003 1 56 29pm Sample Location Above R amp D Lab Technician Jim Ed Brown Instrument Kevin s 431 431 4 SN 3190 Comment DateTime Jan 20 2005 12 51pm Alarm Setpoint 0 023 magina RESULT mg m 3 Readings Minimum Maximum Average O 0 039 0 015 O11 O08 00534 O14 O10 039 O10 E 009 SD 0 0127 An example graph is shown below Site Name Doc Control Address 1912 W 4th Street Tempe AZ 85201 Sample Location Above R amp D Lab Technician Jim Ed Grown Instrument Kevin s 431 4351 4 SN 3190 Comment DateTime Jan 20 2003 12 51pm Alarm Setpoint 0 023 malm 3 Result my m 3 0 000 Jan 20 12PM NE AA A E ee A EEE ee de eee CEF E mn 1 mm mmm mm mmm mmm ey E E a NAAA AEREA AAA AS ERRE AAA AAA AA EE E Day AZI Customer Service 602 470 1414 800 528 7411 or support azic com Jan 20 O6PM Page 17 of 24 Export Report Sends a copy of the report in the file format specified in the File gt Configuration menu to the directory specified in the File gt Configuration menu Deleting or Editing Records To delete or edit records JCS uses the Microsoft Access database and therefore record additions deletions and edits are performed using Access policies e Delete Delete unwanted records by selecting the record select
7. name address and sample location Add all of the sites that are monitored Each site must have at least one sample location specified and can have up to as many locations as are used at the site e Instruments enter the name model and serial number of each instrument used e Technicians enter the names of the technicians that will be using the software or instruments If a name is misspelled and corrected at a future date the correction is applied to all previous data records AZI Jerome Communications Software E felix File Setup Da a ent Window Help Type a question For help E Instrument Checks El is P Imstrumert 3337 Technician Mr Brown Jim s 631 63174 SN 1004 Oct 16 2002 Jim s 621 631 SN 1004 Oct 14 2002 1 Perform Sensor Regeneration D 2 Aun 3 blank Must be 0 002 or less Oct 16 2002 0 100 3 Function Test Module Readings E Sites poo SiteName 17 Address Phoenix Water Treatement Plant 1912 Water Blvd Rercord 14 4 Tempe Water Treatment Plant Phoenix 42 88888 oo agaga Samplelocafi n P Comment Close E Instruments Bo 5 1004 Bo 3 1021 4 Form vier FLTR MUM AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 13 of 24 The Data Logger is used to collect the data from the instrument but first 1t must be programmed To program the Data Logger Connect the JCS Inte
8. of 24 gt Export Format Choose the output format that best suits your needs gt HTML for web browser use gt Microsoft Excel for spreadsheet use gt RTF for general word processing use and gt Text for notepad use gt Serial Port Number Select the AZT Jerome Communications Software computer s serial port number P The selected communications port is not available usually l or 2 Ifthe computer has 7 Do you want to select another port a modem serial port 3 or 4 may need to be selected e Import DOS JCI File If there are files created by the DOS version of Jerome Communication Interface software on the system use this option to bring them into the current Windows based software e Page Setup Print and Exit The last three selections under the File Menu are standard program options to control printing operations and exiting the program Page 12 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com The JCS program uses Microsoft Access to store information The data from the Data Logger is stored in records that are associated with site location records instrument records and technician records Before retrieving new data from the Data Logger the site instrument and technician records must be set up e Instrument Checks provides a place to enter the data from periodic checks of the instrument e Site displays a form to enter site data Enter the site
9. 6 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com This configuration 1s used for Data Logger setup and configuration After programming the Data Logger disconnect the cables and attach the Data Logger directly to the instrument The Data Logger can then control analyzer sampling alarms and data storage The Data Logger has a 1 000 sample data capacity The Data Logger must be reconnected to the computer to download the data Please Note The Data Logger will not operate if it is connected to the JCS Interface Cable It must be connected directly to the instrument to receive power from the instrument and perform auto sampling and data storage e Ensure the computer and instrument are both turned OFF e Locate the DB25 connector marked INSTRUMENT on the JCS Interface Cable and attach it to the back of the instrument e Attach the DB9 connector on the other end of the cable identified as PC to an available serial port on the computer This port will be identified to the JCS during program installation e Connect the remaining DB25 connector identified as DATA LOGGER to the Data Logger This connector has two cables extending from it gt DB25 Connector Installed in Instrument DB25 Connector Installed in ween Data Logger 000 OM i bh DM 0 0 MA DB9 Connector installed in Computer Serial Port AZI Customer Service 602 470 1414 800 528 7411 or su
10. Arizona Instrument LLO USER MANUAL JEROME COMMUNICATIONS SOFTWARE JCS INSTALLATION and OPERATION MANUAL V1 02 for Windows XP May 2009 ARIZONA INSTRUMENT LLC 3375 N Delaware Street Chandler AZ 85225 USA 800 528 7411 602 470 1414 f 602 281 1745 WWW azic com Email General azi azic com International inth azic com Customer Service support azic com ARIZONA INSTRUMENT LLC 3375 N Delaware St Chandler AZ 85225 800 528 7411 sales azic com www azic com MADE IN THE USA AZI P N 700 0042 B Last update May 2009 TABLE of CONTENTS ll INTRODUCTION coca o 4 Z YS TEM REOUIRE MIEN TS ise cusiteiatsas conan saiediuatedtunidadenaaseiietasetadenaunieletuninedanacrriuctanstel 5 3 JIARDWARE INSTALLATION cessise si seseswnicendactrcestmniaeuasasuyesteowsacndatucestmehienacesuvestenmsnantes 6 3 1 Instrument to Computer Direct Interface oooooononcnnnnnnnnononononnnnnnnnnnnnnnnnnnnnnnnnnnos 6 3 2 Instrument to Data Logger to Computer Connection cccccccccccnnnnccnnnnnnnnnononanonnnnnnnnnos 7 4 SOPTWAREANS PALLATTON cocaina 8 Alo platino teo Watescn cd 8 A A A OLA 10 A T A 10 44 Program Revision informato A a 11 De JES MEUS re 11 yen PNG SNM ON 11 22 Sepesi E ia 13 Ds PACT crm E ee cen aso died sta esto ans ecseeseee 14 Fae DAM is 16 o ES CUM E erecta cha cee iaa 19 Ie 231081 05 0259 0 0 ot 0 0 DE O CAE RO ree oN ea Pe Ne ee a 21 Deis GCP AMON sowed N ae Mgnciahel nea en aaa Meat aned v
11. LC Form View e Compact Database clicking on this option compacts the database to take up less disk space if desired Configuration Import IC DOS File e Configuration Sets up the options shown below gt Data Logger Double Check High Readings Click on this check box if the Data Logger 1s to be programmed to Ml Page setup take another sample immediately to verify a high reading a gt Display Help on Startup Check this box if you want Exit the Help file to be displayed each time the program is started It 1s best to check this box until you are familiar with the functions you need to perform on a routine basis gt Report Header Lines Type the information gt 2 E FJ AZI Jerome Communications Software E Program Configuration Data Logger Double Check High Readings Iv Display Help On Startup M Report Header Lines you want to appear at the top of each printed Reportidentifier SSS report in these three lines You do not have to use all of them OO gt Export Directory Enter the directory on the hard drive where you want data and reports stored The default selection stores the data in the directory with the J erome Communication Software program Export Directory c Program Files A2I ICS Export Format Microsoft Excel Serial Port Number k y Close m View For AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 11
12. TA LOGGER JCS Interface Cable A ZI 6000 1055 AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 5 of 24 A Please Note Only the JCS Interface Cable should be installed at this time After the software is installed and operating the security key will be installed in an available USB port 31 Instrument to Computer Direct Interface Use the direct interface configuration when the J erome instrument is connected directly to a dedicated computer The JCS allows the computer to control sampling data storage and data analysis while connected directly to the instrument Ensure the computer and instrument are both turned OFF Locate the DB25 connector marked INSTRUMENT on the JCS Interface Cable and attach 1t to the back of the instrument Attach the DB9 connector on the other end of the DB25 Instrument cable identified as PC Connector to an available serial port Installed on the computer This port will be identified to the In Analyzer JCS during program gt gt installation EE a Breet The remaining DB25 mun y connector on the cable must not be connected It MAN is used only during SN DB9 PC Connector programming of the Data 1 x Logger When it is gt Fy f Installed in connected it will inhibit tf lt Com puter all communication SIA between the instrument serial Port and computer Page
13. cords must be set Site And Location Doc Control AboveR amp DLab up in the Setup menu prior to Auto Technician Jim Ed Brown y sampling Instrument Kevin s 431 431XSN3190 f gt Enter the Sample Interval in Sample Interval 1 to 60 min 16 minutes Do not use a short sample Alarm Setpoint 0 023 o aati interval that would require more than 2 regenerations per day Trya PU F 10 to 15 minute sample interval O EA initially a gt If an unsafe or critical level is known enter that level in the Alarm Setpoint field gt Click on the Start button to begin sampling Test Data n gt The Test Data form opens and 5 eg displays the current samples as they are received from the instrument gt The Time to Next Sample box will appear and show a running time remaining until the next sample will be taken When a sample is being taken the time is replaced with the word NOW 3 gt Clicking on the View Report or TN A View Graph button after at least two samples have been taken will immediately display the collected data currently in the database AZI Customer Service 602 470 1414 800 528 7411 or supportO azic com Page 19 of 24 gt If the alarm level is exceeded the alarm will sound through the computer and the screen will display a flashing warning message as shown Instrument Matts 631 631 50 2478 v a AZI JCS o sto Time to Nest Sample 4 14 e Take One Sample gt Click o
14. device or keyboard Set the cursor on the desired selection and click to select the item The Windows keyboard Alt arrow Tab and Enter keys may also be used The Program Window has the typical drop Ready Pop Tas ul down menu bar across the top of the screen to access program options commands and E JCS Help olx information P Hide Back Print Options homo QUICK START GUIDE Buick Start E Auto Sample E Data PROGRAM E Data Logger Programming CONFIGURATION E Data Logger Data Retrieval E Import E Instrument Checks Setup the PC s E Instruments serial port 2 Program Configuration number by E Requirements selecting the 2 Record Edit Policy i El Security Key Configuration El Sites menu item See E Technicians below to open the Program Configuration form v gt Page 10 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com Click on Help on the menu bar then click on About The AZI logo appears and shows the program s title and version number If you call AZI Customer Service for any reason this version number will be needed to identify the software in use E AZI Jerome Communications Software Ea fx File Setup Data Logger Data Instrument Window Help Type a question For help ES About AZI JCS ADO Arizona Instrument AZI Jerome Communications Software version 1 02 Copyright 2002 2003 Arizona Instrument L
15. e familiarity with the personal computer and Windows operating system being used 1s also recommended If you have any questions about how to proceed call AZI Customer Service at 800 528 7411 or 602 470 1414 or send an e mail to supportO azic com for assistance Page 4 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com Contents of the JCS Kit AZI Y990 0168 Jerome Communications Software on CD ROM USB Security Key JCS Instrument Data Logger PC Interface Cable AZI 6000 1055 This user s manual also on the CD ROM Files on the JCS Program CD ROM JCS installation program JCS and instrument manuals current at the time the software shipped System requirements not included with the JCS Kit Jerome 431 X or 631 X with the Communications Option installed Windows 98 Second Edition Windows ME Windows NT Windows 2000 or Windows XP One available DB9 RS 232 serial port One available USB port Optional equipment Jerome Data Logger AZI P N 6100 0010 to capture data without a computer nearby WARNING A standard serial cable should never be used with the J erome instruments The specially designed JCS Interface Cable AZI part number 6000 1055 uses only four wires between the computer and the instrument Standard serial cables use more wires and could damage the computer or instrument DB9 CONNECTOR TO COMPUTER DB25 CONNECTOR TO INSTRUMMENT DB25 CONNECTOR TO DA
16. ine ae sy 21 O OPEN 22 6 1 Instrument operated from the COMpuUteT oocccccccccnnononcnnnnnnnnononanonnnnnnnnnnnnnnnanncnnnnnnnos 22 6 2 Instrument operated from a Data Logger occcccoonoononnnnnnnnnnnnnnnnnnnnnnnnnnnonnnanonnnnnnnonos 23 Page 2 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com Jerome Communications Software JCS To be used with Jerome 431 X Mercury Vapor Analyzer with the Communications option and Jerome 631 X Hydrogen Sulfide Analyzer with the Communications option APEVAR EAE N a ido File Setup Data Logger Data Instrument Window Help AA Arizona Instrument cars m Z PROPRIETARY RIGHTS NOTICE The material in this manual contains valuable information developed by Arizona Instrument LLC for use with the Jerome line of analyzers No part of this manual can be reproduced or transmitted in any form or by any means electronic mechanical or otherwise This includes photocopying and recording or in connection with any information storage or retrieval system without the express written permission of Arizona Instrument LLC A current electronic copy of this manual can be found on the AZI website at www azic com downloads aspx Copyright 2000 2009 Arizona Instrument LLC All Rights Reserved Windows and Access are registered trademarks of Microsoft Corporation in the United States and other countries AZI Customer Service 602
17. n Take One Sample to direct the instrument to take a sample This selection has the same function as the SAMPLE button on the instrument The measured concentration will be displayed If desired press the Sample Again button to take another sample 9 Sample Reading i Sample value is 000 ppm Sample Again Page 20 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com Type a question for help e This selection operates as it does in many other Windows based programs It tiles open windows horizontally or vertically or cascades them over each other Tile Vertically Cascade Arrange Icons Site Names Phoenix Water Treatement Plant Tempe Water Treatment Plant al Model Serial Number 631 X 1004 631 1021 Record 14 4 1 CECI E of 2 Close Form View NUM e Selecting Contents in the E JCS Help O x Help menu brings up the Help uw amp E a Hide Back Print Options contents listing with a brief explanation of those items meca QUICK START GUIDE necessary for successful B Auto Sample PROGRAM program operation E Data Logger Programming CONFIGURATION gt The Quick Start selection A OS Retrieval in the Contents listing has a e menei o o hyperlinks built into it that Pogan Coniguration abeto can be clicked to navigate ici selecting the to the hyperlinked sections E Security Key oo EE Si
18. nd retain the clock and programming When you are ready to begin sampling Turn the instrument ON Press the sample button When finished sampling Turn the instrument off gt Remove the Data Logger from the instrument and attach it to the JCS Interface Cable connector marked DATA LOGGER gt Ensure the JCS Interface Cable s PC connector is still attached to the computer gt Connect the JCS Interface Cable connector marked INSTRUMENT to the instrument gt Turn the instrument ON Page 14 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com O Click on Data Logger and then on F AZI Jerome Communications Software File Setup Data Logger Data Instrument Window Help Retrieve Data e Select the information for this sampling y EB Data Logger Program x session from the pull down tabs for ES Data Logger RON each line Site And Location APEMANACMICS cue 0 gt e Ensure the date and time are correct Technician MrBrown e Add a comment if desired Instrument Jim s 631 631 XSN1004 7 e Click on the Retrieve button Date Time Jan 17 20031007am gt Data files stored in the Data Logger Commet tOCST will be transferred into the a computer a e After the data is in the computer the dose program loads the Data Form to allow you to view the data on screen Va a a ar AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 15 of 24
19. on Retrieve Data V VvV Y Turn the computer on if necessary and launch the JCS program The data from the Data Logger will be placed in the database and be available for review and or printing Turn the instrument OFF and remove all cabling when finished AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 23 of 24 TRADEMARK AND COPYRIGHT PROTECTION Jerome Arizona Instrument and the stylized AZI are all registered trademarks of Arizona Instrument LLC Instrument firmware and software is copyright protected O Copyright 2000 2009 Arizona Instrument LLC All Rights Reserved Windows and Access are registered trademarks of Microsoft Corporation in the United States and other countries Arizona Instrument LLC Jerome Communication Software Installation and Operation Manual AZI P N 700 0042 B May 2009 If you have any questions regarding the operation of this instrument please call 800 528 7411 602 470 1414 fax 480 804 0656 or send e mail to support azic com Arizona Instrument LLC 3375 N Delaware Street Chandler AZ 85225 800 528 7411 602 470 1414 Fax 480 804 0656 http www azic com email azi azic com General intl azic com International support azic com Customer Support Page 24 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com
20. or arrow on the left of the record and press the Delete key on the computer s keyboard A reminder will appear indicating that the Delete cannot be undone Press Yes to proceed or No to cancel Please note that a record cannot be deleted 1f 1t is associated with other records For example a technician record cannot be deleted if it is referred to by a Data record Delete the Data record first then delete the technician record If the data record must be maintained the technician information will be maintained as well e Edit Edit the fields of a record by typing in the desired field The edits are saved when the form is closed If a field 1s edited the correction 1s applied to all previous data records For example after the address is changed newly printed reports will have the corrected address Edits can also be made from the appropriate selection in the Setup menu For example select Setup Technician to edit the Technician list Page 18 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com File Setup Data Logger Data Instrument Window Help Auto Sample The Instrument menu is used to program the computer to control the sampling rate of the instrument when the instrument is connected to the computer The JCS Interface Cable passes the control signals to the instrument and data to the computer Ma gt wall A e Auto Sample gt The Site and Location Technician BESSE and Instrument re
21. pport azic com Page 7 of 24 4 1 Starting the Software e Turn on your PC and place the JCS Software CD into the computer s CD drive If the program fails to start gt Select Start and Run gt Enter E Install JCS_Install exe where E is the letter identifying ARIZONA INSTRUMENT LLC the CD drive and select OK JCS Installation Copyright 2002 2003 e Click on Install Jerome Communications Software to install the software or Close to abort the installation 4J AZI Jerome Communications Software Setup O Ensure all other runnin g pro grams are E Welcome to the AZI Jerome Communications Software installation a mi program closed before clicking on OK or Setup cannot install system files or update shared files if they are in use Before cli ck on Exit S etup to ab ort th e proceeding we recommend that you close any applications you may be running installation Exit Setup e Click on Change Directory if you want the software to install in a different directory or folder than the E Click this button to install AZI Jerome Communications Software software to the default directory E e Click on the picture button to install the software to the listed directory or click memes on Exit Setup to abort the installation cutsemp Page 8 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com 43 AZI Jerome
22. rface Cable as follows Attach the connector marked DATA LOGGER to the Data Logger Attach the connector marked PC to the computer Attach the connector marked INSTRUMENT to the instrument Turn the instrument ON In JCS click on the Data Logger FJ AZI Jerome Communications Software drop down menu and then click on File Setup Data Logger Data Instrument Window Help 2 Program 83 Data Logger Program The Program Menu allows setting of Sample Interval 0 to 60 min fid the sample interval and alarm setpoint Alarm Setpoint 0 5 value into the Data Logger 431 000 to 999 mg m3 631 000 to 50 ppm gt Do not use a short Sample Interval 1 Programming the Data Logger that would require more than 2 erases existing store datal regenerations per day Try a 10 to Leave Data Logger powered up for a P Ss couple minutes to charge battery 15 minute sample interval initially gt Set the Alarm Setpoint if desired or Program leave it blank A blank alarm Close setpoint has the effect of turning off the alarm Formview PT C Nel f 2 gt Click on the Program button to set the values into the Data Logger Disconnect the JCS Interface Cable from the instrument and Data Logger Attach the Data Logger directly to the instrument gt The Data Logger can be left unpowered for a few hours without losing its time clock Turn the instrument on every few hours for a few minutes to power the Data Logger a
23. tes menu item See j The Help menu can be set to E Technicians below to open display automatically at the Program program startup by checking Configuration i the Display Help on Startup a box in the File gt Configuration window AZI Customer Service 602 470 1414 800 528 7411 or support azic com Page 21 of 24 6 1 Instrument operation from the computer e Connect the JCS Interface Cable s PC connector to the computer and the INSTRUMENT connector to the S DB25 Instrument E Connector instrument Installed e Ensure that the middle connector is not in Analyzer attached to the Data Logger A Fe e Launch JCS on the PC Ee git e Ifall preliminary set up procedures a have been completed and the instrument is turned ON Click on Instrument Click on Auto Sample Select the Site Location Select the Technician Select the Instrument Enter or verify the Sample Interval Enter or verify the Alarm Level Add a comment 1f desired Click on the Start button MU Y gt e L E x SS DBI PC Connector Installed in Computer W Serial Port VVVVVVVV WV e The instrument should take one sample within a few seconds and repeatedly thereafter at the preset rate Page 22 of 24 AZI Customer Service 602 470 1414 800 528 7411 or support azic com ISU UIC O PELati0On 110101 Ensure the instrument is turned OFF Connect the JCS Interface Cable s PC
Download Pdf Manuals
Related Search