User Manual
Contents
1. 1968 SOMA User Manual CMD 404FU www commax com Co Ltd Thank you for purchasing COMMAX products Please carefully read this User s Guide in particular precautions for safety before using a product and follow COMMAX instructions to use a product exactly The company is not responsible for any safety accidents caused by abnormal operation of the product Contents 1 INtOGUCTION ANANG a KN eens 2 2 Important Safeguard 3 3 Product Concept and 4 4 Wiring diagrami sisirin saae n eed 6 5 Configuration of DEVICE ID amp mode 9 6 Specification sasanga 0000 einna 14 5 1 Introduction Your unit is designed so it can be flush mounted on the or used When flush mounted on the wall the stand permils you to the unit for an gular of unit view The model number is located on the bottom and record the serial number in the space provided below available Refer to these numbers whenever you call upon your COMMAX dealer regarding this product Model No Serial No To prevent fire or shock hazard do not expose the unit to rain or moisture A This symbol is intended to alert the use to the presence of uninsulated dangerous Voltage within the product s enclose that may be of sufficient magnitude to constitute a risk of electric shock to persons This sym2. Room numbers are allocated sequentially by the ID number configured Building is fixed as 101 designated ID X 4 will be final channel of room Ex When ID 1 configured Channel 1 Line1 Block 101 unit 1 Channel 2 Line2 Block 101 unit 2 Channel 3 Line3 Block 101 unit 3 Channel 4 Line4 Block 101 unit 4 1 ID X 4 4 Last channel unit number is designated as 4 Ex ID 79 max configured Channel 1 Line1 Block 101 unit 313 Channel 2 Line2 Block 101 unit 314 Channel 3 Line3 Block 101 unit 315 Channel 4 Line4 Block 101 unit 316 79 ID X 4 316 Last channel unit number is designated as 316 Reference On Auto Mode block number is fixed as 101 2 Manual Mode OFF When booted with number 1 switch off it operates on MANUAL mode Irrelevant to ID number configured you can directly set up the block and unit num ber from external device Lobby phone Caution You can only set up MANUAL Mode from separate lobby phone program mode supported 36 After DEVICE ID and mode is set it should be booted with adapter power OFF ON If there was a connection of the common power it should be reconnected after the PORT UTP cable was disconnecte 12 When you register the lobby information to floor distributor from the lobby phone this floor distributor will be set with the building No of lobby phone After that the household unit which is connected with this floor distributor
3. fire or electric shock Never spill liquid of any kind on the product A Lightning For added protection for this product before a lightning storm or when it is left unattached and un used for long periods of time unplug it from the wall outlet and disconnect the other system This will prevent damage to the product due to lightning power line surges If you live in an ared heavily prone to lightning storms it is recom mended that you invest in power line telephone line RF cable and actuator polarization surge protectors to pro tect your appliance system from possible damage 3 3 Product Concept and Features CMD 404FU building distributor is used to interlock with floor distributor CMD 101BU and is developed for interlocking Modum system monitor with lobby and security CMD 404FUis limited to the following devices that can be connected to interlock Lobby phone Export oriented type LOBBY Gate View Multi panel Floor distributor Modum distributor CMD 101BU Required Video phone The video phone for 4 wire way Modum system CMV 43A Adapter RF 2A CMD 404FU Notes on wiring It doesn t guarantee the quality of product for connec tion if you do not keep the following Wire the IN of CMD 404FU with distributor or CMD 404FU installed with OUT on the floor below Wire LINE 1 4 of CMD 404FU with 2 CCTV of MODUME system video phone Max 4 Houses connection CMD 404FU distribute wires up four
4. bol is intended to alert the use to the presence of important operating and maintemance servicing instructions in the A literature accompanying the appliance caution Risk of electric shock do not open CAUTION To reduce the risk of electric shock do not remove cover or back no user serviceable part inside refer servicing to qualified service personnel 2 Important Safeguards A Damage Requiring Service This equipment from the power source and source and refer servicing to qualified service per sonnel under the following conditions when the power is damaged if liquid has been spoiled or objects have hallen into the unit if the equipment has been exposed to rain or water if the equipment has been dropped or otherwise damaged when the equipment exhibits a distinct change in performance this indicates a need for service A Water and Moisture Do not use this product near water for example near a bath tub wash bowl kitchen sink or laundry tub in a wet basement or near a swimming pool and the like A Accessories The product may fall causing serious injury to a child or adult and serious damage to the appliance Any mounting of the manufacture s instructions and should use a mounting accessory recommended by the manu facturer A Object and Liquid Entry Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a
5. can check the image of lobby phone during monitoring mode Initialization When you turn on the product after you set up all switch on or off then factory reset will be initiated Initial value Block101 Unit 1 line1 Unit 2 line2 Unit line3 Unit 4 line4 Caution Product only operates after OFF ON when configured A 6 Specification Spec Transmission type Voltage Wiring Sequence Wiring distance CMD 404FU Floor Distributor Building distributor CMD 101BU 6 lines Polarity MODUME VIDEO PHONE 4 lines Polarity RJ45 CAT5e Patch Cable DC 24V 80mA MAX 1 MODUM System building distributor CMD 404FU gt CMD 404FU IN Input 2 CMD 404FU OUT Output gt Upstairs CMD 404FU IN Expansio 3 CMD 404FU LINE1 2 3 4 gt Monitor MODUM System video phone Maximum 300m Main entrance monitor the distance from each floor distributor to each monitor is limited by 30m One line per lobby 40 floor distributor can be interlocked COMMAX
6. houses on one floor and output common 6 lines after receiving common 6 lines DATA GND LB TALKA B VD_P N from Distributor CMD 101BU Maximum 40 CMD 404FU can be operated within 300 meter from lobby or CCTV The distant from floor distributor CMD 404FU to Modum System video phone is within 30m Separate power source must be connected to CMD 404FU DC24V 80mA or higher Separate power must be connected to CMD 404FU DC24V 80mA or higher In case one source of power is used then maximum devices connected should be Eight Floor distributor should be connected with 27 terminal of camera Caution When interlocking or expanding with external device do connect two or more video phone 4 Wiring diagram VIDEOPHONE VIDEOPHONE VIDEOPHONE VIDEOPHONE 1 2 3 4 LINE1 LINE2 LINES LINE4 IN Loon IN CMD 101BU gt gt BUILDING DC IN_24V DISTRIBUTOR REAR CCTV LOBBY Building distributor CMD 101BU gt CMD 404FU 15 FLOOR gt CMD 404FU 15 FLOOR gt CMD 404FU 2 FLOOR gt gt MODUME VIDEO PHONE UTP CABLE CAT 5e MAX 300m 6 CMD 404FU PORT CMD 1018U DC_IN 24v EIA TIA 5688 ates 4 LB_TALK_A 4 LBTALKB 5 1 CMD 404FU LINE IMODUME VIDEO PHONE EIA TIA 5688 pol 4 WHITE OPTION Use for easy connectio
7. n CMD 101BU CCU 204AGF LINE BOARD CASE MODUM SYSTEM AUDIO GATE SYSTEM SYSTEM LINE IN OUT AUDIO GATE SYSTEM LINE EIA TIA 5688 Nan 2 DATA 4 4 LB TALK B GD TALK A 5 1 GND 60 n i na DC_IN 24V S6001 TYPE et 4 11 5 Configuration of DEVICE ID amp mode When configuring the Device ID set up Dip switch on the back panel of the product Different ID should be used when installing the multiple floor distributor Functions for each switches 1 Select MANUAL AUTO OFF MANUAL ON AUTO 2 4 ID configuration 10 digit figure Composed of BCD code Refer to picture below 5 6 ID configuration single digit figure Composed of BCD code Refer to picture below MANUAL DEVICE 10 MUN e 2nd digi tst digit 123 45 67 8 9 OFF ON Number description method by switches There are three 10 digit figure switches which can be used to seven 0 5 2 2 3 7 j 3 4 5 678 Enter ten digit number 0 7 Enter single digit number 0 9 ID configuration range 1 79 MAX room number can be entered 10 Auto Manual mode function Auto Mode ON When booted with number one switch on it operates with auto mode
Download Pdf Manuals
Related Search