DT398B/ DT398B-MD
Contents
1. DT398C DT398B DT398B MD Federal Communication Commission Interference This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiated radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation if this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 22. this device must accept any interference received including interference that may cause undesired operation Operation on the 5 15 5 25GHz frequency band is restricted to indoor use only The FCC requires indoor use for the 5 15 5 25GHz band to reduce the potential for harmful interference to co channel Mobile Satellite Systems DT Research Inc a i 2000 Concourse Drive San Jose CA 95131 _http www dtresearch com DT Research Copyright 2014 DT Research Inc All Rights Reserved DT Research is a registered trademark of DT Research Inc BOG041614DT398ENG DT Rese arch Mobile POS Tablet DT398C DT398B DT398B MD BASIC OPERATION GUIDE ENGLISH INTRODUCTION Thank you for acquiring the latest addition to DT Research s line of mobile tablets the DT398C DT398B DT398B MD Featuring an IP65 rated slim yet robust enclosure the two pound DT398C DT398B DT398B MD with 9 7 TFT display is powered by the Intel Celeron or Core i dual core processor offering optimal combinations of performance and power savings The DT398C DT398B DT398B MD is available with Windows Embedded Standard 7 Windows 7 Pro or Linux operating systems Each software operating system features web browser client server computing software media player accessories and applications support PACKAGE CONTENTS e DT398C DT398B DT398B MD with internal battery pack stylus and bumpers e AC DC Power Adapter with Power Cord e
3. Basic Operation Guide e Handstrap Major options depending on configuration e Desktop Cradle with External Battery Pack Charger Docking support with ports for Power USB Display Port COM port and Ethernet e External Battery Pack and Battery Charger Kit e Vehicle Wall Mount Cradle If your DT398C DT398B DT398B MD contains camera 3G or scanner module please refer to the Tablet Modules Basic Operation Guide for detailed operation DT398C DT398B DT398B MD DT398C DT398B Wireless Input Output Ports Battery Power LED e SATA USB Hybrid Port Headphone Jack DC Power Input Full Slot Smart Card Reader oO OG SD Slot Button Functions BUTTON ACTION Power on Q Push release typically enters Standby mode or Push release exits Standby mode or restarts software dependent Push and hold over 4 seconds invokes hardware shutdown Programmable As scanner trigger when equipped with the scanner module Programmable O Wireless switch DT398B MD Wireless LED Battery Power LED e ne weal a ama hy E DT398C DT398B DT398B MD Power Battery LED Status e Blue indicates the battery is 25 to 100 charged e Blinking blue indicates the battery is charging e Orange indicates that the battery is between 11 to 25 e Blinking orange indicates that the battery is below 10 e Blinking blue and orange alternately indica
4. connect to other wireless devices or access points If your DT398C DT398B DT398B MD does not come with such a network adapter please consult your device provider to establish the desired network connectivity OPERATION Internal Battery Warning A The Internal battery pack should only be replaced by an authorized DT Research service representative Please contact your product and or service provider for internal battery replacement service Powering ON and OFF To activate the DT398C DT398B DT398B MD push and quickly release the Power Button The display will come on in a few seconds To put the DT398C DT398B DT398B MD in Standby mode push and quickly release the Power Button To turn the DT398C DT398B DT398B MD off for extended storage power off safely using any software function that shuts down computer provided in the software operating system NOTE The battery packs shipped with your tablet may be low in power please use the AC DC adapter with the DT398C DT398B DT398B MD when setting up for the first time to fully charge the internal battery pack You may charge the external battery pack with it attached to the DT398C DT398B DT398B MD or with the optional external battery charger kit NOTE When the battery pack s is are charging the blue colored Battery LED should blink slowly If plugging in the AC DC adapter does not trigger this blinking activity and the LED stays dark the battery pack s may have bee
5. 398C DT398B DT398B MD is equipped with an internal Li lon battery pack and an optional battery pack that clips hot pluggable onto the back of the tablet The period between battery recharges can be significantly lengthened by putting the tablet into Standby mode through the Power Button see Buttons Function Table whenever the tablet is not in use Depending on the operating software the DT398C DT398B DT398B MD may also be configured to enter various power saving modes via the Power Button or through timed entry USING THE DT398C DT398B DT398B MD Peripherals Support Through its USB port the DT398C DT398B DT398B MD supports a wide range of USB based peripherals These peripherals are applicable for software installation applications storage data storage docking or software recovery and update The DT398C DT398B DT398B MD is complemented by an optional Desktop Cradle or Wall Vehicle Mount Cradle for support pass through charging and connection to a range of USB peripherals including keyboard and mouse The Cradles offer the following interfaces a DC in port for the AC DC adapter an Ethernet port a VGA output and USB ports Always seat the DT398C DT398B DT398B MD securely onto the cradle The cradle must be powered by the AC DC adapter for the Ethernet and USB ports to function The battery packs on the DT398C DT398B DT398B MD may be recharged by connecting the AC DC adapter directly to the DC in port on the DT398C DT398
6. B DT398B MD or through the DC in port on the Cradle while the DT398C DT398B DT398B MD is docked Remote Management Depending on software configuration the DT398C DT398B DT398B MD can be centrally managed for asset monitoring and for software control Please consult your device provider For More Support Users can download the Tablet Modules Basic Operation Guides from the DT Research website If the DT398C DT398B DT398B MD comes with a 3G module please contact your product and or service provider for the SIM Card installation procedures To Hold the Tablet Left hand grip the left back side of the tablet with your left hand four index fingers with thumb resting on the top of the back side of the tablet and palm securely against the back Right hand grip the right back side of the tablet with your right hand four index fingers with thumb resting on the top of the back side of the tablet and palm securely against the back
7. k via a USB mouse Wireless Networking Wireless LAN The DT398C DT398B DT398B MD is often delivered with an embedded user inaccessi ble 802 11a b g n WLAN adapter equipped with a hidden custom antenna e Through the support of typical WLAN adapters the DT398C DT398B DT398B MD should be able to detect all 802 11 access points in the vicinity for you to select the access point of your choice for connection e The SSID and WEP WPA WPA2 if enabled parameters on the DT398C DT398B DT398B MD and the access points have to match The SSID is case sensitive and it is recommended that you enable WEP WPA WPA2 encryption or advanced alterna tives for secure access e When WEP WPA WPA2 is enabled you may need to consult your network admin istrator or your networking equipment literature to properly configure associated settings such as Authentication mode etc e Refer to the access point operating manuals for setting up the 802 11 access points Button Management Where supported by software many of the hard buttons on the DT398C DT398B DT398B MD are programmable to perform a function of the user s choice To activate the button re assignment application invoke the Button Manager application Brightness Control To control the screen brightness launch the System Utility The System screen will display a Brightness control section with up and down arrows that can be activated with the stylus Battery and Power Management The DT
8. n drained substantially Try unplugging replugging the AC DC adapter to the DT398C DT398B DT398B MD a few times to activate the charging process NOTE To conserve power use push and quick release the Power Button to put in Standby mode while not in use Pushing briefly on the same button will wake up the system within seconds NOTE Avoid using the Power Button hold 4 seconds feature to turn off the tablet this form of hardware shutdown is intended to be a means of recovery from lockups and not as normal operation Start Up If the power up from Standby or otherwise is successful the appropriate interface will be displayed after a launch sequence of several seconds The wireless LAN connection may take 10 15 seconds to be established Configuring the DT398C DT398B DT398B MD The tablet may be configured using the utilities and methods dictated by the software operating system The DT398C DT398B DT398B MD should be configurable for various properties such as user profiles network features and several system elements DT398C DT398B DT398B MD Calibration The touch display for the DT398C DT398B DT398B MD is calibrated before shipping In the event that the calibration has been modified or is unsatisfactory the respective calibration routines e g PenMount PM to calibrate the touch interface may be used Such applications are typically executed through touch input via Stylus or through mouse clic
9. tes the battery is being warmed up Do not unplug the AC DC adapter Precautions e Always exercise care when operating and handling the DT398C DT398B DT398B MD e Do NOT apply excessive pressure to the display screen e We recommend using the Stylus provided to keep the screen clean e Avoid prolonged exposure of the display panel to any strong heat source Wherever possible the DT398C DT398B DT398B MD should face away from direct light to reduce glare e If the AC DC power adapter is used to recharge or power the tablet do NOT use any AC DC adapter other than the one provided with the tablet or acquired from the manufacturer or its partners e In the unlikely event that smoke abnormal noise or strange odor is present immediately power off the DT398C DT398B DT398B MD and disconnect all power sources Report the problem to your device provider immediately e Never attempt to disassemble the DT398C DT398B DT398B MD as this will void the warranty Basic Features The DT398C DT398B DT398B MD wireless tablet integrates a bright and responsive touch display 1 USB port and embedded networking elements such as wireless LAN or optional 3G The DT398C DT398B DT398B MD is complemented by a suite of accessories including battery expansion docking cradles and wall vehicle mount cradles for a comprehensive user experience A DT398C DT398B DT398B MD typically integrates an 802 11a b g n wireless LAN WLAN adapter that may
Download Pdf Manuals
Related Search