ManualsLib - Makes it easy to find manuals online!
Contents
1. AWAY is used when the user is away from the premise and wants the interior protected Listed below are the steps to arm in the AWAY Mode Step1 Close all protected doors and windows e Ready light will be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is not on or flashing e f the power light is off you have no AC power Restore power if possible If not contact your installing company for service e f the power light is flashing you have a battery failure Contact your installing company for service Step2 X Enter your 4 or 6 digit user code to arm the system e Thearmed and exit lights will illuminate e You may now leave the building IMPORTANT The exit light will flash rapidly for the last 10 seconds of the exit delay as a warning to the user that the exit time is about to expire The user may wish to disarm and rearm the system if more time is needed Making the system ready to arm If the ready light is not on or if it is flashing a zone is not secure To identify this zone check the zone lights A zone light will be on if the zone has been bupassed If a zone light is flashing that zone is in alarm or has been faulted If a zone light is flashing rapidly it means that the zone is in a trouble condition Arming your system in the STAY mode2. STAY is used when the user is inside the premise and wants protection around the perimeter Listed below are the steps to arm in the STAY Mode Step1 Close all protected doors and windows e Ready light must be on or flashing when all protected zones and sensors are secure NOTE If any zones are bypassed a sensor in that zone can be violated without affecting the ready light e The security system will not arm if the ready light is not on or flashing e f the power light is off you have no AC power Restore power if possible If not contact your installing company for service e f the power light is flashing you have a battery failure Contact your installing company for service Step2 X Enter your 4 or 6 digit user code Optional if programmed NX 108 116 124E User manual Page 9 10 11 05 Downloaded from www Manualslib com manuals search engine Networ 9 Step 3 e Press the STAY key e The bypass light will illuminate indicating that all interior zones are bypassed All interior devices will bypass automatically giving the user freedom of movement within the interior area e For each interior zone bypassed the corresponding zone light will also illuminate If any zone s have been bypassed previously by the user the lights corresponding to the bypassed zonels will illuminate alerting the user that a zone s may be unprotected and can be faulted without an alarm The stay light will also illuminate Note normally all e
3. an entry exit delay by pressing the STAY key again The instant light will go out Disarming the system When you enter the protected area through one of the designated Entry Exit doors the keypad control will sound a solid tone for the duration of the entry delay time or until you enter a valid code After entering a valid code the red armed light will go off and the tone will stop The security system is now DISARMED If a valid code is not entered before the end of the entry delay an alarm will occur NOTE If the red armed light is flashing during the entry delay the alarm system has been activated in your absence Leave the building immediately and call your alarm company and or the police from a safe location NX 108 116 124E User manual Page 10 10 11 05 Downloaded from www Manualslib com manuals search engine w Networ g CANCEL ABORT feature optional The cancel light will flash during an abort delay time If a code is entered followed by the CANCEL key while this light is flashing all abortable reports will stop the communication process NOTE The abort feature must be enabled Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on until the central station has received the cancel report NOTE The cancel feature must be enabled Bypassing zones If you wish to bypass one or more zones this must be done whi
4. followed by a slow flashing light EMERGENCY ACTIVATION KEYS e CE amp 3 Fire Auxiliary Emergency Police NOTES You must hold these keys for 2 seconds to activate these functions Your system may not be programmed for these activation keys You should press these keys only in an emergency situation that requires response by emergency personnel If your system is programmed for these functions the following reports can be sent Fire Key This key can activate the fire alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Auxiliary Emergency Key This key can activate the auxiliary alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be sent to that center Police Panic Hold Up Key This key can sound a local audible alarm when pressed for two seconds If your system is connected to a monitoring center an emergency report could be transmitted to that center NOTE Some Panic Hold Up alarms are programmed to be silent at the protected site while reporting an alarm to the monitoring center Check with your installing company to determine how your security system will respond to the Panic Hold Up activation NX 108 116 124E User manual Page 8 10 11 05 Downloaded from www Manualslib com manuals search engine D Networ 9 KEYPAD FUNCTIONS Arming your system in the AWAY mode
5. Networx Series NX 108 116 124E LED keypad User manual imagination at work Downloaded from www Manualslib com manuals search engine Downloaded from www Manualslib com manuals search engine Networ TABLE OF CONTENTS TABLE OF CONTENT S ease e 3 INTRODUCTION nieis a oaa Oar a aE na ar E EESE EEESC EEEO EO SA EEEE EES 4 GLOSSARY OF TERMS r Ee e aaa Eaa ea aeea Oa Eora oa Eora Eaa E SPE seesseasonieads 5 KEYPAD DISPLAY E A D e A E A E S 6 UNDERSTANDING THELIGHTS ttai casis an a ere trt br m A A R A A 6 EMERGENCY eicu liacs 8 KEY PAD FUNCTIONS EE A couse E A A T E E EEE E E AEE ET EEEE E E EEEE 9 ARMING YOUR SYSTEM IN THE AWAY MODE sesssesssessssssecssessssssesssessscssssssscssscsusssssssscsuscsucssscsusesuecssssascsasssecssecssscssscsusssusssssssscsucscessessesssecssecseesseesesees 9 MAKING THE SYSTEM READY TO ARM asssscssssssczascosesseosesssseraisassocotsosnsosasnesesssr sustahusnvescusnsesosavigcnussdsssstbunandsesdesonssasassscosssosss sucnabsassecobsvensosesbusesser suatdaoseseeh ARMING YOUR SYSTEM IN THE STAY MODE Be USING THE QUICK ARM OPTIONAL sesssessssssesssssesssssscsssssecsssucsssssecsssssscssuesssssseessuesssssvecsssssesssuessssusesssuesssssscsssuessssecsssessssueesssnsesssuessssssesssueesssneesssetessae CHANGINGIMODES WHILE SYSTEM ARMED irohin te tette tote Ebor eet tete een
6. T Press the 6 key The zone light s that is illuminated corresponds to the system fault s below 6 Line Trouble Line Cut This light will illuminate when there is telephone line trouble or the telephone line has been cut The service light will remain lit until the telephone trouble clears and a user code is entered 7 Auxiliary Comm Device Fail Radio backup has failed 7 FAILURE TO COMMUNICATE This light will illuminate when there is a failure to communicate between your system and the central station 8 LOSS OF SYSTEM TIME This light will illuminate when there has been a loss of power and your system clock needs to be reset EXIT Press the 4t key to exit the Service Light mode Note This fault is global in nature and will affect all partitions of a multi partition system NX 108 116 124E User manual Page 7 10 11 05 Downloaded from www Manualslib com manuals search engine Networ Zone Light The zone lights are off when everything is normal A zone light will be on if the zone has been bypassed If a zone light is flashing that zone is in alarm or has been faulted If a zone light is flashing rapidly it means that the zone is in a trouble condition Trouble conditions are Tamper Hardware Low Battery Loss of supervision A combination of Alarm Fault and Tamper Trouble will produce a rapid flashing light for a short period of time
7. ages need to be completed by your installer Keep these tables in a safe place Installing Service Company Address Telephone number Name central station Telephone number central station Function codes programmed Controls function action Entry exit delay times in seconds Exit delay time Secondary Exit delay time E x Entry delay time Secondary Entry delay time This system counts zones Programmed functions O Abort delay QO Forced arming LJ Battery test O Group bypass Q Cancel alarm 0 Quick arm Q Change partitions LED U Re Exit Q Chime U Service Light Message enabled QO Communicator test O Siren test Q Manual fire alarm Q Manual medical alarm Q Manual panic alarm NX 108 116 124E User manual Page 17 10 11 05 Downloaded from www Manualslib com manuals search engine w Metwo ry g Zone descriptions Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Zone 9 Zone 10 Zone 11 zone 12 zone 13 Zone 14 Zone 15 Zone 16 Zone 17 Zone 18 Zone 19 Zone 20 Zone 21 Zone 22 Zone 23 Zone 24 NX 108 116 124E User manual Page 18 10 11 05 Downloaded from www Manualslib com manuals search engine www gesecurity net EMEA Distribution is a division of GE Security EMEA bvba COPYRIGHT 2005 GE Security EMEA bvba All rights reserved GE Security EMEA bvba grants the right t
8. arm memory Step 1 Press the key Step 2 Press the 3 key to display the zone s on the keypad that created the last alarm Step 3 The ALARM MEMORY feature will flash those zones that created alarms and will light steady those zones that were bypassed during the last alarm Test function optional If programmed this function will perform a battery test communicator test and or a siren test Step 1 Press k 4 4 The test will be performed as programmed Step 2 If the siren test is performed enter a user code to silence the siren No alarms will be sent and no reports will be sent unless a communicator test is performed at which time a test signal will be sent NX 108 116 124E User manual Page 14 10 11 05 Downloaded from www Manualslib com manuals search engine w Metwo ry g Detector reset function This function is used to reset Smoke Detectors and Zone Troubles Your system must be Disarmed to use the Reset function Step 1 Press sk 7 Resets have now been performed The FIRE light will go off if the smoke detectors have been reset Step 2 If the keypad begins beeping the reset did not execute properly Enter your code to silence the keypad Wait a few minutes and repeat step 2 to attempt another reset If the keypad still beeps after repeated attempts please contact your installer Setting the system clock Step 1 Enter 9 7 Step 2 Enter master code Step 3 Enter the hour code which must
9. be two 2 digits Note The clock is a 24 hour clock Refer to the following table Time Hour Code Time Hour Code 12 00 Midnight 00 8 00 AM 1 00 AM 01 9 00 AM 2 00 AM 02 10 00 AM 4 00 AM 04 12 00 Noon 5 00 AM 05 1 00 PM 6 00 AM 06 2 00 PM 7 00 AM 07 3 00 PM Step 4 Enter the minutes code which must be two 2 digits Example 7 minutes after would be entered 0 7 10 00 PM 11 00 PM 09 17 18 NX 108 116 124E User manual Page 15 10 11 05 Downloaded from www Manualslib com manuals search engine w Metwo ry g Setting the system date Step 1 Enter k 9 6 Step 2 Enter master code Step 3 Enter the Day of Week 1 Sunday 3 Tuesday 5 Thursday 7 Saturday 2 Monday 4 Wednesday 6 Friday Step 4 Enter the Month Code Must always be two 2 digits 01 January 05 May 09 September 02 February 06 June 10 October 03 March 07 July 11 November 04 April 08 August 12 December Step 5 Enter the Day Code Must always be two 2 digits Example The 5 would be entered as 0 5 Step 6 Enter the last two digits of the Year Code Example For 2003 enter 0 3 KEYPAD CONTROL TONES BEEPS A sounder is built into the keypad If programmed your system keypad may sound for any of the following reasons e Beeps for all keypresses Sounds a continuous tone during the Entry delay time Pulses when a day zone is violated while the system is d
10. e ben ea eee teet AA oet altes oce DISARMING THE SYSTEM seee CANCEL ABORT FEATURE OPTIONAL BYPASSING ZONES 5 cicccs sississeszecasssnussasasncvechassisnssaasiaceusdiasssassauedusoscbbussVaqsodeoodsobacadnescouessdiotassadecesuddossboseinasvancdes a aa AT a AS ivens GROUP BYPASS IEIUNII UT TURNING THE DOOR CHIME ONANG OFF sssssssssssssissssvasvsscvassenssasvassssasuasousacnssssagosecussovesnsasasgsossevactassovaasocasasaunsstasguastasezonasnhcnsnseaebdssndbssunsstesacesbsbannvee ADDING AND CHANGING USER CODES cecsccsscssecssecessessssssssseseceesscesceseesceeseecesescessesecaecaceseeseeessesscaecsceseeseeseeeaeeceeses 12 ASSIGNING USER CODE AUTHORITY LEVELS ccccsssssssssssssssscsscescesccecsessessesssssessececeeseeceecssensestestecessesscsseesausaeeseestenss 13 OTHER KEYPAD FUNCTIONS c 14 SETTING THE KEYPAD TONE sssscssatssssssctsssvasdasedadeusbsststabessnensonstoousnsusscasbucovstaluanacsigabusouanauadcsdsdssbbucdunngusstadicuatonsduatas6sasbasobaboeseussbiitoncgasatasdaubisccoucensseeabbedses 14 CHANGE PARTITION OSIN A E Se i sese ei eet uM D EE E ME EE 14 VIEW ALARM MEMORY TEST FUNCTION OPTIONAL DETECTOR RESET FUNCTION SETTING THE SYSTEM CLOCK SETTING THE SYSTEM DATE KEYPAD CONTROL TONES BEEPS sccsssssccccsssssssescecsescsescecsesesescacsesesesescesscseseusessesessssssecsnsseseacacueseseacusue
11. ggle the chime feature on off and produce a momentary ding dong sound NX 108 116 124E User manual Page 11 10 11 05 Downloaded from www Manualslib com manuals search engine Networ ADDING AND CHANGING USER CODES Your system must be Disarmed to add change user codes Step 1 Press k 5 Step 2 Enter a Master Arm Disarm Code NOTE For partitioned systems someone changing the code of another person must have access to all or more partitions than the user being changed Step 3 The ready light will flash Step 4 Enter the 2 digit applies to NX4 6 8 or 3 digit applies to NX8E user number always enter 2 digit such as 0 3 for user 3 or 1 0 0 for user 100 Step 5 Enter the new four 4 or six 6 digit user code NOTE To delete a user code enter k sk k 3k for a 4 digit code or 3K sk 3k sk 3k sk for a 6 digit code Step 6 The ready light will flash indicating you are back at Step 4 above If the code is rejected the sounder will beep 3 times Step 7 If another user code needs to be programmed return to Step 5 Step 8 Press the key while the ready light is flashing to exit the User Code Programming Mode NX 108 116 124E User manual Page 12 10 11 05 Downloaded from www Manualslib com manuals search engine N Networ g ASSIGNING USER CODE AUTHORITY LEVELS Assign authority levels to users by following the steps below Assign user codes before assigning au
12. in with this system relates specifically with two major factors 1 The quantity quality and placement of security devices attached to this system 2 The knowledge you have of the security system and how that knowledge is utilized in a weekly test of the complete system You should be aware of the following facts when preparing a safety security plan for your home business 1 Your security system is an electronic device and is subject to failure or malfunction Do not rely on it as your single source of security 2 Your system should be tested weekly 3 Your system will not work without power 4 Warning devices will need to be loud enough wired correctly and properly placed to provide notification of an alarm event 5 Smoke and heat detectors may not detect heat and smoke in all situations 6 Use qualified security professionals to install and maintain your security system 7 It may be possible to arm the security system without the backup battery connected Your periodic test should be done with AC Power removed to verify the battery is connected and adequately charged 8 Care should be taken to plug in and restrain the AC transformer after testing Please read the following information and instructions carefully before operating your security control system NX 108 116 124E User manual Page 4 10 11 05 Downloaded from www Manualslib com manuals search engine N Networ g GLOSSARY OF TERMS Abort Delay An option that a
13. isarmed Pulses when a FIRE zone has a trouble condition Beeps 3 times for trying to arm with the Ready light off if Force Arming has not been selected Beeps for 1 second or emits a ding dong sound for the Chime feature Beeps during an exit delay beeps rapidly for the last 10 seconds of an exit delay and beeps 1 second at the end of the exit delay Pulses when the armed status changes and the AC power is off Pulses when the armed status changes and any zonels are bypassed Pulses when the armed status changes and a low battery is detected Pulses when the armed status changes and a Tamper condition is detected Beeps to indicate Telephone Line Cut if selected Pulses when one or more of the following conditions are detected Zone or Box Tamper Low Battery AC Power Fail or Expander trouble e Beeps 3 times every minute indicating a low battery or missing transmitter is detected if wireless device is in system Entering code will suppress the sounder for 12 hours Entering a valid code will silence the keypad sounder when it is pulsing The arm disarm state of your system will not change when entering a code to silence a pulsing keypad sounder Please contact your installer if a trouble condition exists NX 108 116 124E User manual Page 16 10 11 05 Downloaded from www Manualslib com manuals search engine Networ APPENDIX A REFERENCE TABLES IMPORTANT These reference tables on the following p
14. le the system is in the disarmed state The following steps are used for bypassing zones Step 1 Press the BYPASS key Step2 Enter user code if required optional The bypass light flashes Step 3 Enter 1 or 2 digits indicating the zone you wish to bypass Example Press the 1 key for zone 1 press 1 2 for zone 12 Step 4 Press the BYPASS key again Step 5 The corresponding zone light will illuminate indicating the zone has been bypassed Repeat steps 3 and 4 for any other zone s that need to be bypassed Step 6 Press the BYPASS key again or press the key to exit the Bypass Mode The bypass light will stop flashing upon exiting the Bypass Mode Group bypass By pressing the BYPASS key followed by the 0 0 key then the BYPASS key again all zones that are designated as group bypass zones will be bypassed Press the BYPASS key again to exit group bypassing Unbypassing To manually unbypass zones perform the bypassing procedure on a zone that is already bypassed The corresponding light for that zone will go off when unbypassed NOTE All zones will automatically be unbypassed each time the system is disarmed Turning the door chime ON and OFF The door chime feature must be enabled by your installer The door chime is turned on or off by pressing the CHIME key If the chime is on the chime light will be illuminated If the chime is off the chime light will be off Each press of the CHIME key will to
15. llows a delay in reporting to the central station Authority Level The level of access an individual has when using an alarm panel Central Station The location where alarm data is sent during an alarm report Chime Feature An option that allows the keypad to sound a ding dong whenever an entry exit door is opened Codes Can be either User Codes relating to a person or Function Codes a toggle switch to turn specific functions on off NOTE A system may have either four digit codes or six digit codes but not a mixture of the two Duress Code An option that allows a special code to be sent to the central station that indicates the alarm system is being operated under duress Forced Arming An option that allows the system to be turned on ARMED with one or more zones open A system that is ready to be force armed will flash the ready icon Note Those zones that are not ready will not create an alarm Function Code A Function Code is either a four 4 or six 6 digit code that has been programmed by the installer to operate a device Group Bypass An option that allows the user to bypass multiple zones with a single operation Instant Delay An option that allows an instant alarm condition for Entry Exit doors or grants a delay to allow someone to enter exit the building without an alarm or before entering a user code to disarm Master Code A master arm disarm code that can program other user codes Partitioned System A system di
16. ntry exit doors will be delayed To change entry exit to Instant press the STAY key again The instant light will illuminate indicating that the entry exit doors have no delay To change entry exit to Delayed press the STAY key again The instant light extinguish indicating that the entry exit doors are delayed Step 4 Using the Quick Arm optional The Quick Arm feature may be used if it is enabled Quick Arm will allow the user to arm the security system without entering a user code Quick Arm in the AWAY mode is possbile by pressing the EXIT key The system can be quick armed in the STAY mode by pressing the STAY key This feature is used for ARMING ONLY and will not disarm the security system This is ideal for a maid or baby sitter code etc Changing modes while system armed Step1 Pressing the STAY key will turn on off toggle a delay on Entry Exit doors and turn on off toggle the instant light Step2 Press the BYPASS key at this time to turn on off toggle all designated interior zones This is only possible if programmed by your installer bypass toggle option set Step 3 When armed pressing the EXIT key will start the Exit delay enabling you to leave the building This is only possible if programmed by your installer re exit option set IMPORTANT The instant light needs to be off at this time if you plan on re entering the building otherwise you will create an alarm You may re initiate
17. o reprint this manual for internal use only GE Security EMEA bvba reserves the right to change information without notice Downloaded from www Manualslib com manuals search engine
18. ore zone lights will illuminate indicating what service s is required Call your service provider immediately for these problems Below is a listing of what each digit means in a service condition LIGHT PROBLEM l SYSTEM FAULT Press the 1 key The zone light s that is illuminated corresponds to the system fault s below 1 Over Current Fault 5 Expander Low Battery 2 Siren Trouble 6 Expander Box Tamper 3 Box Tamper 7 Expander Trouble 4 Expander Power 8 Ground Fault Note Faults 1 amp 2 are global in nature and will affect all partitions of a multi partition system Press the key to return to the 1 of 8 service lights 2 ZONE TAMPER Press the 2 key and the zone light s will illuminate showing the zonel s that are tampered Press the key to return to the 1 of 8 service lights 3 ZONE LOW BATTERY Press the 3 key The zone light s will illuminate showing which zonels has a low battery This only applies to wireless zones Press the key to return to the 1 of 8 service lights 4 ZONE LOSS OF SUPERVISION Press the 4 key and the zone light s will illuminate showing which zone s has loss of supervision This only applies to wireless zones Press key to return to the 1 of 8 service lights 5 ZONE TROUBLE Press the 5 key and the zone light s will illuminate showing which zonels has a trouble condition Press the key to return to the 1 of 8 service lights 6 TELEPHONE FAUL
19. sesescesecsensesecseees 16 APPENDIX A wiiddid emm M M 17 NX 108 116 124E User manual Page 3 10 11 05 Downloaded from www Manualslib com manuals search engine N Networ g INTRODUCTION This manual is furnished to help you understand your security system and become proficient in its operation All users of your security system should read and follow the instructions in this booklet and if possible practice on the keypad control while your professional installer is on site Failure to do so could result in the security system not working properly Please keep this booklet in an accessible location for the life of the security system If you do not understand any part of this manual you should notify your installing company The SECURITY CONTROL PANEL can be turned on ARMED and off DISARMED by entering a 4 or 6 digit code into the keypad control which is similar to a telephone keypad If your security control panel has been so programmed you may be able to turn on ARM your system by simply pressing the STAY or EXIT key The system must always be disarmed using a 4 or 6 digit code The LED keypad includes up to 35 lights and a built in electronic sounder These provide specific information relating to the status of the security system which is described in the booklet Understanding what the lights and sounds mean will help you to easily operate your system Keep in mind the level of security you will obta
20. the light will go off denying access to partition 2 Refer to chart shown below LIGHT PARTITIONS ASSIGNED Partition 1 Partition 2 Partition 3 m 1 2 3 6 8 Step 8 When the partitions are assigned press the x key This returns you to Step 3 previously mentioned At this point you may enter another user number to assign authority level Repeat Steps 4 8 until you have assigned authority levels to all user numbers Step 9 Press the key to exit the Assigning Authority Level Program NX 108 116 124E User manual Page 13 10 11 05 Downloaded from www Manualslib com manuals search engine N Networ g OTHER KEYPAD FUNCTIONS Setting the keypad tone Step 1 Press the x key Step 2 Press the 0 key Keypad is now in the Adjust Tone mode Step 3 Pressing the 1 key will make the keypad sounder go to higher tones pressing the 2 key will make the keypad sounder go to lower tones Step 4 When the desired tone is reached press the key to set this tone and exit from the Adjust Tone mode Change partition optional Step 1 Press the k key Step 2 Press the 1 key Step 3 Press a NUMBER key between 1 and 8 to change partitions momentarily Step 4 If no other key is pressed it will go back to its standard partition in ten seconds Step 5 If another key is pressed the system will remain in the new partition until no keys have been pressed for 60 seconds View al
21. thority levels Your system must be in the disarmed state to change user code authority levels Step 1 Press k 6 Step 2 Entera Master Arm Disarm Code NOTE Someone changing the authority of another person can only add or remove partition authorization for partitions to which they have access Step 3 The ready light will flash Step 4 Enter the 2 digit applies to NX4 6 8 or 3 digit applies to NX8E user number Always use leading zeros when necessary i e 004 for user number 4 Step 5 Lights illuminated indicate the authority levels assigned to this code An explanation of the lights is listed below You may toggle turn on off the authority level by pressing the number for that authority level LIGHT AUTHORITY LEVELS IF LIGHT 8 IS OFF Reserved Note Do not change if on 1 3s 5 Ambsm 6 wsos 8 If this light is on this code is programmed as a function code Do not change Press 1t to exit Step 6 Press the k key The ready light will flash This moves you to the partition enable The user has access in partitions that are illuminated Step 7 The illuminated numbers indicate each partition where the user has access To change any of the partitions where the user has access press numbers corresponding to areas where you want to give the user access or deny access Example If zone light 2 is lit then the user is assigned access to partition 2 By pressing the 2 key
22. until the central station has received the cancel report NOTE The cancel feature must be enabled See Cancel Abort Feature Chime Light The chime light is on when the chime feature is on off otherwise Exit Light The exit light is on during the exit delay Please note that the light will flash during the last 10 seconds of the exit delay as a warning that the time is running out The user may want to disarm the system if the exit light is flashing in order to prevent an alarm The user may then re arm the system and exit before the delay expires Fire Light A steady fire light means a fire zone has been faulted A rapidly flashing fire light means that a fire zone is in a trouble condition NX 108 116 124E User manual Page 6 10 11 05 Downloaded from www Manualslib com manuals search engine w Metwo ry g Power Light The power light is on if the primary power is on The power light will flash if the system has a low battery condition Ready Light The ready light is on when the system is ready to arm and flashes if ready to force arm The ready light is off when the system is not ready to arm because of a zonels being faulted Stay Light The stay light is illuminated when all interior zones are bypassed Service Light The service light will be on if the security system requires service If the service light is on press the key followed by the 2 key to determine the service condition One or m
23. vided into multiple areas in which its own user or users control each area Perimeter The outer edge of the protected area Quick Arm An option that allows you to turn on ARM the security system by pressing either the STAY or EXIT key on the keypad control for ARMING only as programmed by the installing company User Code A four 4 or six 6 digit entry code used to arm or disarm the system NX 108 116 124E User manual Page 5 10 11 05 Downloaded from www Manualslib com manuals search engine gt Networ g KEYPAD DISPLAY amp LED s Understanding the lights Ready Light Power Light Service Light Armed Light z Instant Light nd a 5 6 Fire Light 9 e d e 85 C9 Numeric code entry keys E I Pull out zone ID Tab Bypass D E Cancel E 3k ji Zone Lights m a y 5 function keys 3 emergency activation keys Armed Light The armed light is on when the system is armed The armed light is off when it is disarmed The armed light will flash when there has been an alarm during the previous arm cucle Bypass Light The bypass light is on when any zone in this keypad s partition is bypassed If the bypass light is off no zones are bypassed Cancel Light The cancel light will flash during an abort delay time Entering a code followed by the CANCEL key during or after an alarm report to the central station will cause the cancel light to come on It will stay on
Download Pdf Manuals
Related Search