manual - PACLITE Equipment
Contents
1. For your own personal protection and for the safety of those around you please read and ensure you fully understand the following safety information lt is the responsibility of the operator to ensure that he she fully understands how to operate this equipment safely If you are unsure about the safe and correct use of the walk behind floor saw consult your supervisor or Paclite Equipment Improper maintenance can be hazardous Read and understand this section before you perform any maintenance service or repairs CAUTION General Safety e The owner of this machine must observe and also train the user of the machine to observe the effective labour protection laws in the country of application e This machine is to be used for is intended application only e This machine must only be operated by well trained personnel e Personal Protective Equipment PPE must be worn by the operator whenever the equipment is being used e Cordon off the work area and keep members of the public and unauthorised personnel at a safe distance e Make sure you know how to safely switch this machine OFF before you switch it ON in case you run into any difficulties e Always switch OFF the engine before servicing it e During use the engine becomes very hot Always allow the engine to cool down before touching it e Never leave the engine running and unattended e Never remove or tamper with any fitted guards they are there for your own protection I2. Engine will not start Blade not turning Excessive noise vibration or wobble from blade No fuel getting to engine Engine switched off Spark plug fouled Engine cold Honda Engine flooded Belts incorrecily tensioned Belts broken Check condition of arbor shaft bearings Check Drive Pin for damage Check tightness of arbor shaft nut Check condition of blade flange Check blade for signs of damage Walk behind Floor Saw Manual Open fuel tap Fill fuel tank Switch engine on Clean check and reset plug gap Close choke Open choke fully open throttle pull recoil starter until engine fires Re tension belts Replace belts Replace as necessary Replace Drive Pin Tighten as necessary Replace as necessary Replace blade 13 Technical Data Model PRECISION CUT 400 m Engine Type 4 Stroke Gasoline Max Power Output Hp kW 13 9 6 9 6 9 Max Engine Speed rpm 3 600 Cutting Depth 14 Walk behind Floor Saw Manual Transportation and Storage Extreme Care must be taken when transporting loading or unloading this machine CAUTION e For long term storage empty the fuel in the carburetor by running the engine with the fuel tap closed e The chemical composition of the fuel will deteriorate after prolonged storage When the machine needs to be stored for a long time remove all the fuel from the fuel tank and the water from the water tank
3. adjust the belt tension after the first 4 hours then as necessary To change the belts Remove the belt guard and loosen screws on drive idler fixing plate which will reduce the belt tension enabling the removal of the drive belt Install the new belt and loosely tighten the plate should still be able to move the screws on the drive idler fixing plate Using a spanner on the tightening screw apply torque to the drive idler so that the drive idler is forced against the drive belt Ideal torque is 50Nm If you have no torque wrench then the belt should deflect around 7 8mm at its slackest point Once the torque of the belt is set tighten the centre slot bolt to hold the position of the idler and then tighten the remaining bolts Re affix the belt guard Water Tank Remove the water tank cap by turning anti clockwise Fill water tank with water only Refit the cap by turning clockwise The flow of water from this machine is designed only to suppress airborne concrete dust and should therefore only be used with DRY cutting diamond blades CAUTION Never fill the water tank with any flammable liquids or gasoline as serious injury or death could occur CAUTION 11 Routine Maintenance Before Each Operation Every 50 Hours of Operation As required Clean Air Filter Element Inspect Belts tension after the first 4 hours then 12 Trouble Shooting Possible Causes Countermeasures Problems
4. rias 2006 42 CE Directiva de Compatibilidade Electromagn tica 2004 108 CEE conforme corrigido pelas 92 31 EEC amp 93 68 EEC O numero de vibra es est de acordo com a directiva 2002 44 CE LB A directiva de baixa voltagem 2006 95 CEE BS EN ISO 12100 1 2 Seguran a da maquinaria e s normas harmonizadas afins se aplic veis As emiss es de ruido respeitam e est o dentro das directivas para m quinas 2005 88 CE Anexo VI artigo 12 sendo o organismo notificado TUV Rheinland Product Safety GmbH Am Grauen Stein D 51105 Koln Germany PRODUCT TYPE TYPE DE PRODUIT TIPO DE PRODUCTO TIPO DE PRODUCTO MODEL MODELE MODELO MODELO SERIAL No N DE SERIE N DE SERIE N DE SERIE DATE OF DATE DE FECHA DE DATA DE MANUFACTURE FABRICATION FABRICACI N FABRIC WEIGHT icones POD Sissi casada PESO unica PESO aa _ A a PACLITE Equipment A A e e y e e e e e e i e e e cm Quality Manager On behalf of Uni corp Europe Directrice de Qualit au nom de Uni corp i Europe S A R L Anita Tan Foreword This manual has been written to help you operate your walk behind floor saw safely lt is intended primarily for dealers and operators of Paclite Equipment walk behind floor saws It is recommended that you keep this manual or a copy of it with the mach
5. re fuelling use a proper funnel and avoid spilling over the engine e When re fuelling DO NOT smoke or allow naked flames in the area e Spilt fuel must be made safe immediately by using sand If fuel is spilt on your clothes change them e Store fuel in an approved purpose made container away from heat and sources of ignition Health amp Safety Fuel Do not ingest fuel or inhale fuel vapors and avoid contact with your skin Wash fuel splashes immediately If you get fuel in your eyes irrigate with copious amounts of water and seek medical attention as soon as possible Exhaust Fumes The exhaust fumes produced by this machine are highly toxic and can kill Make sure the work area is adequately ventilated WARNING PPE Personal Protective Equipment Suitable PPE must be worn when using this equipment i e safety goggles gloves ear defenders dust mask and steel toe capped footwear with anti slip soles for added protection Wear clothing suitable for the work you are doing Always protect skin from contact with concrete dd did Component Material In order to protect the AY environment please recycle any ES discarded apparatus or accessories The table beside provides you with a list of the machine s components and their respective materials Take the discarded apparatus to the relevant recycling facilities Walk behind Floor Saw Manual Machine Description Precision Cut 400 Operation Handle Wat
6. retighten knobs once handles are positioned e Be sure cutting line is well defined e Move the saw into operating position Starting the Engine e Check to be sure blade is raised not in contact with the slab surface and blade guards are in place e If wet cutting open water valve for the sprinkler system Check to be sure water flows freely to the blade Water should be visible on the ground around the blade e Make sure you have an adequate supply of water e Open throttle and allow engine to reach operating speed Starting and Controlling the Cut e Engine must be at FULL THROTTLE e When manoeuvering the walk behind floor saw make sure the blade is raised high enough so it does not strike the ground Blade damage may occur if the blade strikes the ground while manoeuvering e Do not manoeuver the machine on inclined surfaces with the manual push engaged or by lifting drive wheels from the ground Loss of braking control will cause the machine to freewheel down the incline e To move the Slot Depth Control Hand Wheel into place slowly turn hand wheel in the DOWN direction until the blade comes in contact with the slab surface e Do not allow the blade to drop onto the pavement surface blade damage will result e Set the Depth Gauge at ZERO e Continue turning the hand wheel until the blade has penetrated the slab to the desired depth NOTE Depth Gauge is an approximate measurement it is not exact Never cut deeper t
7. Also remove the fuel from the float chamber of the carburetor by draining the fuel out from the drain plug e Wash away asphalt concrete accumulated on the walk behind floor saw Clean the engine mounting plate Apply a light coat of oil on arbor shaft blade retaining cap and backing plate to prevent rust formation Cover the machine and store it in a dry place e Always use the lifting hook for hoisting purposes Use proper hoisting equipment and techniques e Remove the blade before transporting or hoisting Serious personal injury or damage to the equipment can result Do not transport the machine with the engine running e Be certain the area surrounding the machine is clear of personnel before hoisting 15 Warranty Your new Paclite Walk behind Floor Saw is warranted to the original purchaser for a period of one year 12 months from the original date of purchase The Paclite Equipment warranty covers defects in design materials and workmanship The following are not covered under the Paclite Equipment warranty 1 Damage caused by abuse misuse dropping or other similar damage caused by or as a result of failure to follow assembly operation or user maintenance instructions 2 Alterations additions or repairs carried out by persons other than Paclite Equipment or their recognised agents 3 Transportation or shipment costs to and from Paclite Equipment or their recognised agents for repair or assessment against a warranty c
8. CE Aromen PACLITE Equipment ei EC DECLARATION OF CONFORMITY DECLARATION CE DE CONFORMITE DECLARACI N DE CONFORMIDAD CE DECLARA O 000 Signed by Signature CE DE CONFORMIDADE We Uni corp Europe 33 Avenue Pierre Brossolette 94048 Creteil Cedex France hereby certify that if the product described within this certificate is bought from an authorised Paclite dealer within the EEA it conforms to the following directives Machinery Directive 2006 42 EC Electromagnetic Compatibility Directive 2004 108 EC as amended by 92 31 EEC 93 68 EEC The physical agent vibration conforms with the directive 2002 44 EC The low voltage directive 2006 95 EC BS EN ISO 12100 1 2 Safety of machinery and associated harmonised standards where applicable Noise emissions conform to directive 2005 88 EC Annex VI for machines under article 12 the notified body is TUV Rheinland Product Safety GmbH Am Grauen Stein D 51105 Koln Germany Nous soussignons Uni corp Europe 33 Avenue Pierre Brossolette 94048 Cr teil Cedex France certifions que si le produit d crit dans ce certificat est achet chez un distributeur de la marque d pos e Paclite au sein de la EEA celui ci est conforme aux norms CEE ci apr s Norme de la machine 2006 42 CE Norme compatible pour l lectromagn tisme 2004 108 CE modifie par 92 31 CEE et 93 68 CEE Le nombre de vibrations est en accord avec la directive 2002 44 CE Caract ristiques basse
9. air filter is clean Excessive dirt dust accumulation within the filter element will cause erratic engine operation Clean the air filter element when it is contaminated See Service amp Maintenance Section 6 Check for fuel and oil leaks Start and Stop Procedure Improper operation can be hazardous Read and understand this section before you start the machine CAUTION Before starting the engine make sure that the Safety Switch is in the ON position and the Throttle Lever is set to the idle position 1 Verify the correct blades for the job have been chosen and that they are properly installed Inspect the blades carefully for damage Never use any questionable blades Check to be sure the blades are free of obstructions and the area is clear for operation Visually inspect the walk behind floor saw Check that all fasteners are secured and mechanical parts are in proper working order Before Starting Gasoline Engine 1 Check the oil in the engine crankcase Be sure to maintain the proper level per the engine manufacturer specifications If the oil is dirty and in need of changing follow the Engine User Manual instructions 2 Check the fuel supply Refer to Engine User Manual Walk behind Floor Saw Manual Operation Before Starting the Engine e Visually check to be sure that the blades are free of obstructions and the area is clear for operation e Adjust the handles for operator comfort and safe operation Be sure to
10. er Tank Cap Lifting Hook Water Tank Alignment Marker Blade Guard Blade Belt Guard 9 Engine A po E E ic 10 Emergency Stop Button 11 Slot Depth Gauge 12 Slot Depth Control Hand Wheel 13 Throttle Lever 14 Tachometer also with hour meter 15 Locking Mechanism Please note Due to improvements and changes in the equipment the illustrations shown may be different from the actual machine Intended Use This walk behind floor saw is intended to be used in the wet or dry sawing of old and new concrete and asphalt Not to be used for dry cutting in the EU as it is not equipped with a dust port Pre Start Checks The following pre start inspection must be performed before the start of each work session or after every four hours of use whichever is first Please refer to the service amp maintenance section for detailed guidance lf any fault is discovered the walk behind floor saw must not be used until the fault is rectified 1 Thoroughly inspect the machine for signs of damage Make sure all guards are in placed and secured 2 Check hoses filler openings drain plugs and any other areas for signs of leakage Fix any leaks before operating 3 Check the engine oil level and top up as necessary Use proper engine oil with the proper viscosity SAE 10W 30 recommended 4 Check the engine fuel level and top up as necessary Use clean fuel Use of contaminated fuel may damage the fuel system 5 Check the
11. f they are damaged or missing DO NOT USE THE MACHINE until the guard has been replaced or repaired e Never use a wet blade without an adequate supply of water to the blade e Never touch or try to stop a moving baled with your hand e Do not cut deeper than 2 5cm per pass with a dry blade e Never touch a dry diamond blade immediately after use Blades require several minutes to cool the machine has been switched off e Always switch OFF the engine before transporting it moving it around site or servicing it e Do not operate the machine when you are ill feeling tired or when under the influence of alcohol or drugs e This machine is designed to eliminate the possible risks arising from the use of it However risks DO reside and these residual risks are not clearly recognisable and may cause personal injury or property damage and possibly death If such unpredictable and unrecognisable risks become apparent the machine must be stopped immediately and operator or his supervisor must take appropriate measure to eliminate such risks lt is sometimes necessary that the manufacturer must be informed of such an event for future counter measuring Fuel Safety Fuel is flammable lt may cause injury and property damage Shut down the engine extinguish all open flames and do not smoke while filling the fuel tank WARNING Always wipe up any spilled fuel e Before re fuelling switch off the engine and allow it to cool e When
12. h Control Hand Wheel anti clockwise d Use a spanner to loosen and remove the 4 M8 bolts that fix the blade guard latch plate Remove the blade guard latch plate e Lift up the blade guard front f Loosen and remove the blade shaft nut that secures the outer flange in position Remove outer flange g Remove the old blade h Ensure the blade shaft arbor inner flange and outer flange are clean and free of foreign objects If they are not clean them so that they are i Fit the new blade onto the shaft arbor The direction of rotation should be shown by the arrows on the blade and blade guard front j Affix outer flange to the blade shaft arbor Ensure that the locking pin passes through the blade and into the inner flange k Rotate the out flange and blade in the opposite direction of the blade rotation to remove the slack Affix the blade shaft nut m Lower blade guard front n Re affix and tighten blade guard latch plate 10 Walk behind Floor Saw Manual Check Engine Oil before Each Operation Refer to the Engine User Manual for specific instructions Change Engine Oil Every 50 Hours of Operation sooner if necessary Inspect Belts Remove the belt guard then check the belt tension by placing light finger pressure on the top of the belt as near as possible to the centre between the engine drive and gearbox pulley The belt should deflect by between 7mm 10mm On new machines after installation of new belts
13. han the maximum depth of cut for the blade being used Only cut in a forward direction Always cut with the engine at full throttle CAUTION e Machine speed is controlled by using the throttle lever e Actual cutting speed is determined by type of blade material to be cut and depth of cut e Do not force the blade while cutting Use proper forward speed and allow the blade to cut and not climb out of the cut or stall in the cut NOTE If while cutting the front wheels start to lift reduce forward speed For positioning the saw the maximum forward speed is 60mm per minute For safety reasons when in reverse move at a slow walking pace DO NOT FORCE IT TO GO FASTER CAUTION e Always cut in a straight line Do not force a turn in the cutting line as blade warpage or breakage may result If the blade stalls in the cut and stops power source e Raise the blade completely out of the cut e Check the blade flanges and nut bolt to be sure they are tight e Remove open guard and secure To Stop Cutting e Stop moving the machine forward e Raise the blade in the UP direction to be clear of the cut e Turn off the water valve e Return the Throttle Lever to the idle position and allow to cool e Shut off the engine e Do not leave the machine until the blade has completely stopped e Make sure you choke the wheels to prevent the machine from rolling Parking the Walk behind Floor Saw The parking brake on the right hand side rea
14. ine so that it is readily available for reference Before you operate or carry out any maintenance on this machine YOU MUST READ and UNDERSTAND this manual Should you have ANY QUESTIONS about the safe use or maintenance of this machine after reading this manual ASK YOUR SUPERVISOR or CONTACT Paclite Equipment on 65 6756 7688 Paclite Equipment reserves the right to change machine specification without prior notice or obligation Directions with regard notations Text in this manual to which special attention must be paid are shown in the following way This CAUTION sign indicates a potential hazard which if ignored could result in injuries to the operator and or those close by as well as damaging the machine CAUTION This WARNING sign indicates a potential hazard which if ignored could result in the DEATH of the operator and or those close by WARNING Contents a po IP em dane ee demandas 2 a 3 4 E o DR RE cases 4 Machine DE SCE LO rascar or 5 Pre Start Checks iii nn nn nn nana anna R RR nn anna anna erra acena anna ce rera renan anaaao 6 SA And SON POUR atenas 6 ODA P O 7 8 Service and Maintenance oooocccnnnccccccononccnnnnnnononnnnncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnrnnnnnnnrnnnnnnrrnnnnnnnnnnnnas 9 12 TOUDE STO o ig 6 RAR ed iaa 13 lie e M DAN PR E e ECO EA 14 Transportation and SION a ei inercia D a e ii E 15 MVEA AAA O Po POP E OU O 16 Walk behind Floor Saw Manual Safety Information
15. laim on any machine Materials and or labour costs to renew repair or replace components due to fair wear and tear The engine air filter and the engine spark plug Paclite Equipment and or their recognised agents directors employees or insurers will not be held liable for consequential or other damages losses or expenses in connection with or by reason of or the inability to use the machine for any purpose Warranty Claims All warranty claims should firstly be directed to Uni corp Europe either by telephone by fax by email or in writing For warranty claims Uni corp Europe S A R L Paclite Equipment 33 Avenue Pierre Brossolette 94048 Cr teil Cedex FRANCE Tel 33 0 1 4981 6955 Fax 33 0 1 4898 4088 Email sales paclite equip com 16 NOTE A TUVRheinland Precisely Right PACLITE Equipment Uni corp Europe S A R L Paclite Equipment 70 Avenue du G n ral de Gaulle 94000 Cr teil FRANCE 33 0 1 4981 69 55 33 0 48 98 40 88 Y sales paclite equip com B paclite equip com
16. of round arbor holes Do not use any questionable in r r Id r It WARNING blades since serious injury and or damage to property could result e Do not use warped twisted or out of balance blades e Unbalanced blades will wear excessively vibrate and damage both arbor shaft and bearings For safety reasons Paclite Equipment does not recommend the use of abrasive blades Abrasive blades can break and cause serious personal injury to the operator and or bystanders If abrasive blades are used by choice only use WARNING those which are marked as reinforced abrasive blades e Make sure you have the proper blade for the job Determine the proper hardness and composition of the slab Give your dealer complete information including the desired depth of the cut and the length of the cut If in doubt contact the blade manufacturer Never exceed the maximum operating speed of the blade Do not remove or lift the blade guard unless the blade has stopped completely and the engine is off WARNING Blade Will Not Cut Blade is glazed or too hard for job Cracked Segments Segment Loss and or Core Usually insufficient Wrong blade for the job water Arbor Hole Out Of Round Blade not properly tightened or seated on arbor Figure 1 Possible Diamond Blade Problems Changing Blades a Open front cover b Set engine start switch to the OFF position c Raise the blade to its highest position by turning the Slot Dept
17. r wheel is designed to hold the machine on a slope of not more than 10 degrees with the rear wheels facing downhill maximum weight should be on the braked wheels Engaging the Parking Brake e Pull the lever toward the centre of the machine and rotate upwards 180 degrees Disengaging the Parking Brake e Pull the lever toward the centre of the machine Then rotate downwards 180 degrees and release to lock in position Walk behind Floor Saw Manual Service and Maintenance Before carrying out any maintenance on this machine ensure the engine has been switched off The engine should also be allowed to cool as parts of the CAUTION engine become hot during use The Paclite Equipment Walk behind Floor Saws are designed to give many years of trouble free operation It is however important that the simple regular maintenance listed in this section is carried out It is recommended that an approved Paclite Equipment dealer carry out all major maintenance and repairs Always use genuine Paclite Equipment replacement parts the use of spurious parts may void your warranty Before any maintenance is carried out on the machine switch off the engine and disconnect the HT lead from the spark plug Always set the machine on level ground to ensure any fluid levels will be correctly read Only use recommended oils Before Changing Blades Inspect all blades carefully before installing Check for cracks loose segments and oversized worn or out
18. tension 2006 95 CEE BS EN ISO 12100 1 2 Norme de s curit des machines et des crit res associ s et configur s si applicable Les missions debruit sont conformes la directive 2005 88 CE Annexe VI pour machines article 12 L objet mentionn est TUV Rheinland Product Safety GmbH Am Grauen Stein D 51105 Koln Allemagne La Sociedad Uni corp Europe 33 Avenue Pierre Brossolette 94048 Cr teil Cedex France por el presente documento certifica que si el producto descrito en este certificado es comprado a un distribuidor autorizado de Paclite en la EEA este es conforme a las siguientes directivas 2006 42 CE de la CEE Directiva 2004 108 CEE sobre Compatibilidad Electromagn tica seg n enmiendas 92 31 CEE y 93 68 CEE El numero de vibraciones esta de acuerdo con la Directiva 2002 44 CE Directiva sobre Bajo Voltaje 2006 95 CEE BS EN ISO 12100 1 2 de Seguridad de Maquinaria y Niveles armonizados est ndares asociados donde sean aplicables Emisi n de Ru dos conforme a la Directiva 2005 88 CE Anexo VI para m quinas bajo articulo 12 la mencionada unidad est TUV Rheinland Product Safety GmbH Am Grauen Stein D 51105 Koln Germany O signat rio Uni corp Europe 33 Avenue Pierre Brossolette 94048 Cr teil Cedex France pelo presente declara que se o produto descrito neste certificado foi adquirido a um distribuidor autorizado do Paclite em qualquer pais da EEA est em conformidade com o estabelecido nas seguintes directivas comunit
Download Pdf Manuals
Related Search