EC3-EC4 elektra en.indd
Contents
1. 1 2 Safety instructions for the User This grill is to be operated by competent persons only and only after careful reading of this complete manual The device may not be used for other purposes than it has been designed for Take into account that the grill is very heavy and can become very hot during operation The device is not allowed to be moved during operation Movement is only allowed in cooled condition Never place objects on the grill not even when it is switched off During use the device has to be equipped with a dripping tray Never leave a device in operation unattended Prevent overheating of the power cord Never use damaged cords First disconnect the electrical connections with the device remove the plugs from the sockets before cleaning the grill in the event of defects or failures for repairs and in the event of accidents or calamities if necessary de activate the relevant fuses Repairs and maintenance on the device are to be done by qualified professionals exclusively Insertion and removal of the spit is only allowed when the device has cooled down Also be extremely careful when adjusting the spit position moving the heat shield moving or emptying the dripping tray or dripping drawer and when placing and using the hand cross Protect yourself wear heat resistant gloves Caution after the electric elements have been switched off the Robax ceramic glass wil2. YOU NEED TO COMPLY WITH ALL NATIONAL REGIONAL AND LOCAL REQUIREMENTS AND REGULATIONS DAILY CLEANING REGULAR MAINTENANCE AND PERIODIC INSPECTION OF THIS DEVICE ARE ESSENTIAL 1 SAFETY INSTRUCTIONS 1 1 Safety instructions concerning Installation Connecting and Locating The power supply has to comply with all national regional and local requirements and regulations The grill is for professional use and should only be connected by qualified professionals in accordance with all valid requirements and regulations Before connecting check if the device is suitable for the electricity present The device has to be placed level and on a solid base Make sure the space where the device is placed is appropriately ventilated It is preferable to place the device directly under an extraction system This may be mandatory Consult the appropriate authorities In case the device is placed directly under an extraction system this system has to be sufficiently heatproof and manufactured in non flammable materials The distances and temperature mentioned below are recommendations The guidelines applying in your case may differ from them Consult the appropriate authorities Incase the device is not placed directly under an extraction system make sure there is a free space above the device of at least 100 cm If this is not possible attend to a heat resistant isolation above the device with a minimum of 100 x 100
3. Power Power Power regulator regulator regulator 1 2 3 175 3175 3 175 bob dd Ld d uj MET OT Seeker 1 13 PEN 2 6 2 6 2 6 Plug 1 Electric Electric Electric element element element 13 N 3 Mot n m n om m gm oor M e jme 230 V 400 V 1600 230 V 400 V 1600 230 V 400 V 1600 PE EC O 4 E EC U 4 E 1 1 1 1 un Power Power Power Power regulator regulator regulator regulator 1 2 3 4 3175 3175 3175 3175 tito Heats tit i Poe ou 13 PEN 2 6 2 6 2 6 2 6 Plug 1 LI ma 1i Electric Electric Electric Electric element element element elemert 13 N 4 r A r A r n om n gm m Re n gm Motor M ence me 25 ni 12 13 N 230 V 400 V 1600 230 V 400 V 1600 230 V 400 V 1600 230 V 400 V 1600 PE GENERAL SAFETY REGULATIONS IMPORTANT YOU HAVE TO STUDY THIS MANUAL CAREFULLY BEFORE HAVING THIS DONER KEBAP GRILL CONNECTED AND BEFORE OPERATING THIS GRILL OR ALLOWING IT TO BE OPERATED THIS GRILL IS BE CONNECTED MAINTAINED OR REPAIRED BY QUALIFIED PROFESSIONALS EXCLUSIVELY THE QUALIFIED INSTALLER TOO HAS TO STUDY THIS MANUAL CAREFULLY BEFORE CONNECTING MAINTAINING OR REPAIRING THIS GRILL WHEN YOU LET OTHERS OPERATE THIS GRILL THEY TOO HAVE TO STUDY THIS MANUAL CAREFULLY BEFORE OPERATING THIS GRILL
4. the kind of meat the thickness and height of the meat on the spit the position of the spit vertical or horizontal the distance of the meat from the Robax ceramic glass the electric elements One or more elements may be switched on After use all the elements must be switched off O position Caution after the electric elements have been switched off the Robax ceramic glass will remain very hot for some time 5 PLACING THE SPIT 5 1 Placing the Spit Model EC O top spit drive mechanism Read the instructions below completely and carefully before placing a spit with meat in the grill for the first time Refer to the drawings on page 4 and 5 Place the dripping tray 15 under the bottom guide column 12 Slide the bottom spit holder 14 towards you for the first time preferably to the end stop 13 and fasten the adjusting knob 14 Slide the upper spit holder 7 towards you for the first time preferably to the end stop 6 and fasten the adjusting knob 8 Slide the heat shield 2 backwards and fasten the adjusting knob 2 Place the spit 9 with meat in the bottom spit holder 14 Lift the upper guide column 1 Place the upper spit point 9 below the upper spit holder 7 Lower the guide column 1 so that the upper spit holder 7 slides over the spit 9 Move the bottom spit holder 14 and or the upper spit holder 7 to place the spit with meat in the desired grill positio
5. the device Never use a water jet The grill may not be immersed 7 2 Cleaning the Robax Color High Trans Ceramic Glass Always use only soft clean lint free cloths Never use for example abrasive sponges Always use only a specially developed cleaning agent for ceramic hob plates The manufacturer of your ceramic glass has tested and approved the following products Cera fix Ceraclen or Vitroclen When used regularly these approved products will form an invisible protective coating on the ceramic glass reducing the ability of food remnants to stick to the surface and also making daily cleaning easier Never use chemical or aggressive agents such as for example detergents abrasives oven sprays grill cleaners or spot removers These agents leave the ceramic glass unprotected and may cause permanent damage such as scratches discolouration and dullness For persistent dirt a special scraper may be carefully used for example Cera quick You should always read carefully the relevant instructions before using a cleaning agent CAUTION Prior to connecting the grill Make sure that the ceramic glass has been cleaned before switching on the electric elements for the first time clean the ceramic glass with a damp cloth and rub it dry then apply a special cleaner to provide a protective coating After using the grill After the electric elements have been switched off the ceramic glass will remain very hot for some tim
6. DONER KEBAP GRILLS MODELS EC O AND EC U ELECTRIC VERSION INSTALLATION OPERATION AND MAINTENANCE INSTRUCTIONS READ THIS MANUAL CAREFULLY BEFORE HAVING THIS GRILL INSTALLED BEFORE OPERATING THIS GRILL EC O 3 E EC O 4 E Model EC O has a top motor ur a 0 it I ai 1l T x EC U 3 E EC U 4 E Model EC U has a bottom motor Naomi Grills Subject to modifications Naomi Grills B V TECHNICAL SPECIFICATIONS Type EC O 3 E EC O 4 E Number of electric elements 3 4 Mains 230V 400V 50Hz 3 N PE Current 3x16A Power consumption 4 8 kw 6 4 kW Heating surface w x h 24 x 63 cm 24 x 80 cm Max meat weight 60 kg 80 kg Dimensions w x d x h 56 5 x 81 0x 98 5 cm 56 5 x 81 0x 115 0 cm incl power regulators Weight 32 kg 35 kg Type EC U 3 E EC U 4 E Number of electric elements 3 4 Mains 230V 400V 50Hz 3 N PE Current 3x16A Power consumption 4 8 kW 6 4 kW Heating surface w x h 24 x 63 cm 24 x 80 cm Max meat weight 60 kg 80 kg Dimensions w x d x h incl power regulators Weight 40 kg 45 kg 56 5 x 66 5 x 98 5 cm 56 5 x 66 5 x 115 0 cm Motor 230 V 50 Hz 3 5 W 1 Revolution per minute Switch positions off clockwise Il counter clockwise TABLE OF CONTENTS DRAWINGS DESCRIPTIONS Models EC O page 4 5 Models EC U page 6 7 Electrica
7. ans Ceramic Glass power cord motor insert nut motor housing cord guide upper guide column hinge socket Model EC U top motor Placing the spit 9 DRAWINGS DESCRIPTIONS Models EC U bottom motor 1 eee E 4 5 back B 000 oom Anu ooo ooo nam 7 Cin a N 7 1 upper guide column 2 upper spit holder with adjusting knob 3 end stop 4 locking for spit 5 spit 6 power cord motor 7 spit board 8 motor in housing 9 motor switch 0 off clockwise ll counter clockwise 10 dripping tray with outlet 11 dripping drawer 12 ball spit drive mechanism 13 14 15 16 17 18 19 20 21 22 23 10 bottom spit holder A locking pin for bottom spit holder B locking pin for spit board guide rails for the housing of the electric elements with adjusting knob power cord electric elements power regulator housing of the electric elements heating surface Robax Color High Trans Ceramic Glass socket bearing fitting for motor motor Placing the spi Model EC U bottom motor 7 ELECTRICAL DIAGRAMS EC O 3 E EC U 3 E 11 12 I3 N
8. cm to limit the ceiling temperature to a maximum of 70 C The distance between the top of the device and the ceiling has to be at least 50 cm in this case The device can be placed apart from in between or adjacent to other devices The available space left and right has to measure at least 20 cm Keep a space of at least 10 cm at the back of the device Keep space available at the front with a minimum of 100 cm measured from the heating surface the ceramic glass The device may under no circumstances be placed in the vicinity of flammable walls curtains furnishings decorations or other flammable materials Therefore the device also may not be placed on flammable support such as for example plastic or wood use for example stainless steel o The heat is intensive Make sure that flammable materials are removed to a safe distance from the device around the device Fire regulations must be scrupulously observed Always take care of optimum fire prevention the appropriate extinguishing materials and of adequate knowledge of how to deal with fires The appliance must be placed on a robust structure IF the appliance will be used in a closed area always use a hood for air ventilation min 100 cm min 20 cm min 1O cm min 60 cm J lt Ss se CES E max 85 cm
9. e wait until it has cooled down completely 8 MAINTENANCE It is essential to maintain the grill regularly considering hygiene reliability in operation and safety Depending on the frequency of use and the age of the device it should be checked entirely at least every two years considering operation and safety Have maintenance exclusively done by qualified professionals 9 GUARANTEE This grill s guarantee is completely taken over by the dealer where the new device was bought Without the original receipt of this purchase all guarantee obligations expire All obligations also expire if non qualified professionals installed maintained or repaired this grill if any part of this grill has been replaced by non original Naomi Grills B V parts if the grill is not operated professionally or used for purposes other than for which it is intended if any instruction from this manual has not been observed The guarantee conditions have to be supplied by the dealer in question Naomi Grills IMPORTANT NAOMI GRILLS B V DISCLAIMS ANY LIABILITY FOR DAMAGE OR BODILY INJURIES RESULTING FROM THE FAILURE TO OBSERVE CAUTION OR CAREFULNESS EVEN IF NOT DESCRIBED Subject to modifications Naomi Grills B V Naoni Grills B V Anton Philipsweg 9 11 e 1422 AL Uithoorn The Netherlands Telephone 31 297 560 170 Telefax 31 297 560 187 email info naomi grills com www naomi grills com Naomi Grills 11 2010
10. ing the spit with meat in the grill Slide the upper spit point 5 in the upper spit holder 2 and lock it 4 Move the upper spit holder 2 to bring the spit with meat in the desired vertical or diagonal position and fasten the adjusting knob 2 Move the housing 19 to place it at the required distance from the meat and fasten the adjusting knob 16 6 REPLACING THE MOTOR 6 1 Model EC O top spit drive mechanism Delivery options for defect motor 1 Complete set of motor in housing switch spit holder power cord with plug or 2 Separate motor Replacement of the motor has to be done by a qualified professional Consult the dealer where the new device was bought 6 2 Model EC U bottom spit drive mechanism Replacement of the motor has to be done by a qualified professional Consult the dealer where the new device was bought 7 CLEANING 7 1 Cleaning General Before cleaning the grill first disconnect the electrical connections with the device remove the plugs from the sockets and wait until the grill has cooled down completely Daily clean the entire grill very thoroughly after use Avoid corrosive abrasive or other aggressive agents using for example for the stainless steel special grill cleaner Do not use hard sharp or scratching objects Do not allow water or other fluids to penetrate
11. l diagrams page 8 TECHNICAL SPECIFICATIONS page 2 GENERAL SAFETY REGULATIONS page 9 1 SAFETY INSTRUCTIONS page 10 1 1 Safety instructions concerning Installation Connecting and Locating page 10 11 1 2 Safety instructions for the User page 12 2 CONNECTING page 13 2 1 Connecting General page 13 2 2 Heat shield Models EC O page 14 2 3 Cord guide Models EC O page 14 3 INITIAL USE page 14 4 USING THE ELECTRIC ELEMENTS page 15 5 PLACING THE SPIT page 16 51 Models EC O page 16 5 2 Models EC U page 17 6 REPLACING THE MOTOR page 18 6 1 Models EC O page 18 6 2 Models EC U page 18 7 CLEANING page 18 7 1 Cleaning General page 18 7 2 Cleaning Robax Ceramic Glass page 18 8 MAINTENANCE page 19 9 GUARANTEE page 19 9 DRAWINGS DESCRIPTIONS Models EC O top motor 1 upper guide column 2 heat shield with adjusting knob 3 motor in housing 4 motor switch 0 off clockwise ll counter clockwise 5 ring for manual spit operation 6 end stop 7 upper spit holder 8 adjusting knob motor upper spit holder 9 spit 10 spit board 11 locking pin for spit board 12 13 14 15 16 17 18 19 20 21 22 23 bottom guide column end stop bottom spit holder with adjusting knob dripping tray with perforated cover power cord electric elements power regulator heating surface Robax Color High Tr
12. l remain very hot for some time 2 Eur 2 1 Connecting general Before connecting the device electrically refer first to the specifications on the type plate on the device the technical specifications on page 2 and the electrical diagram on page 8 Check whether a 400 V electricity supply is available for connecting with the device All electrical supplies to the device must be grounded Ifthe available electrical supplies are not suitable contact an accredited installer and or your electricity supply company The device must be connected by plug connection and therefore not by permanent direct connection Have connections and modifications only done by qualified professionals including the attachment of plugs Specification of electric elements Number of electric elements EC O 3 E EC U 3 E 3 EC O 4 E EC U 4 E 4 Mains 230 V 400 V 50 Hz 3 N PE Power consumption EC O 3 E EC U 3 E 4 8 kw 1 6 kW per element EC O 4 E EC U 4 E 6 4 kW Current 3x 16A Motor specifications Mains 230 V 50 Hz Power consumption 3 5W Revolutions 1 Revolution per minute Switch positions 0 off clockwise Il counter clockwise Cables a grounded cable for the electrical elements without plug to be fitted to be connected to a grounded 400 V electrical socket Model EC O a grounded silicon cable with plug suited for 40 to 180 C to be connected to a grounded 230 V elect
13. n vertically or diagonally closer to the heating surface 18 the Robax ceramic glass or further from the heating surface Attention Always loosen one spit holder first move it and fasten it again Only turn to the other spit holder after completion of the previous steps Place the heat shield 2 in the desired position and fasten the adjusting knob 2 All actions mentioned above can be done with running non running motor this makes no difference at all tg 5 2 Placing the Spit Model EC U bottom spit drive mechanism Read the instructions below completely and carefully before placing a spit with meat in the grill for the first time Refer to the drawings on pages 6 and 7 Put the motor in the off position 10 Slide the housing of the electric elements 19 backwards as far as possible and fasten the adjusting knob 16 Place the upper spit holder 2 at correct distance from the housing 19 considering the thickness of the spit with meat and fasten the adjusting knob 2 Open the locking 4 of this spit holder 2 Place the spit 5 with the bottom spit holder 14 on the ball 13 Attention Make sure the bottom spit holder 14 has already been fastened to the spit 5 by means of the locking pin 15A before plac
14. rical socket Model EC U a grounded cable with plug to be connected to a grounded 230 V electrical socket 2 2 Heat shield only for Models EC O The movable heat shield protects the motor better against overheating Always take care of placing the shield in an optimum position to ensure that the motor is as well protected as possible at all times 2 3 Cord guide only for Models EC O The heat shield is fitted with a spiral The electrical cable of the motor has to be fed through this spiral to prevent that the cable comes nearby the burners Make also sure that the cable does not come into contact with other parts of the grill that may become extremely hot Warning Make sure all the packing materials and foil are removed before the electric elements are switched on for the first time Make sure that the Robax ceramic glass is cleaned before the electric elements are switched on for the first time refer to chapter 7 2 4 USING THE ELECTRIC ELEMENTS The grill is fitted with electric elements that are located directly behind the Robax Color High Trans Ceramic Glass Each element is separately regulated by its own power regulator A positions are stipulated on the power regulator 0 1 2 and 3 Between the O position off and the 3 position full every desired position may be set continuously By selecting the appropriate position the meat may be grilled quickly or slowly or kept warm taking into account
Download Pdf Manuals
Related Search