Cost-effective HD IR Waterproof Fixed Network Camera User`s Manual
Contents
1. network camera address to check connection is OK or not 5 2 Login and Main Interface Open IE and input network camera address in the address bar See Figure 5 1 Blank Page Windows Internet Explorer gt e gtettsek e we de btenkPage H Input your IP en address here Internet R100 Figure 5 1 IP address The login interface is shown as below See Figure 5 2 Please input your user name and password Default factory name is admin and password is admin Note For security reasons please modify your password after you first login 15 IP Camera Username Password Figure 5 2 Web login If it is your first time to log in system pops up warning information to ask you whether install web plug in or not after you logged in for one minute For detailed plug in installation please refer to the Web Operation Manual included in the resource CD After you logged in you can see the main window See Figure 5 3 16 IP Camera fh Substream E Figure 5 3 Web monitoring window Please refer to the Web Operation Manual included in the resource CD for detailed operation instruction 17 I can not boot up the device or operate properly The water leakage occurred IR video is poor Please click RESET button for at least five seconds to restore factory default setup The unauthorized front or rear cap remove many result in2. 100 Activation event video storage image snapshot log email function and etc Record Priority Manual gt Video detect gt Schedule Storage Support display local storage status Management ice eon 1 channel wire Ethernet port 10 100 Base T Ethernet Standard HTTP TCP IP ARP IGMP ICMP RTSP RTP UDP RTCP Network Protocol SMTP FTP DHCP DNS DDNS PPPOE UPNP NTP Bonjour SNMP Remote Monitor system setup file download log information maintenance Operation upgrade and etc Restore Default Reset button Setup IR light pe 20 30M Power DC 12V power and PoE 6W MAX Consumption Working Temperature Working sil Humidify 10 90 Dimensions mm 62 9 64 3 146 8 Weight 370G Excluding box Installation Support bracket installation 10 C 60 C 1 4 Factory Default Setup Please refer to the following sheet for factory default setup information SUONIPUOI m III Setup OSpIA Default Setup Hem IPC HFW2100 Series BLC Mode Off Mirror Off Flip Off Profile Management Normal lt Bit stream S type General T Encode mode H 264 4 Resolution 720P 1280 720 D 2 Frame Rate PAL 25 FPS NTSC 30 Main Stream Bit Rate Type CBR Recommende PAL 1536 6124 Kb S d Bit NTSC 2048 6144Kb S Bit Rate 4096 Frame PAL 50 interval NTSC 60 Watermark DigitalCCTV character Enable Enable Bit stream G
3. Duration 8 minutes GER 5 seconds Disk Full Overwrite Record Mode Automatic Default Setup IPC HFW2100 Series Record Stream Main Stream Device Name Device factory SN Language English Video Standard Date Format Y M D Time Format 24H Time Zone GMT 08 00 Local Host PAL Current Time Sync DST Enable Disable DST Type Date Date and time Start Time 00 00 00 January 17 End Time 00 00 00 January 2 Synchronize with NTP NTP Server clock isc org Disable Port 123 Update Period Anonymous e Auto Reboot Enable Tuesday 02 00 Auto Maintenance Auto Delete gt Old Files SES 10 minutes 2 Structure 2 1 Multiple function Combination Cable You can refer to the following figure for multiple function combination cable information See Figure 2 1 Figure 2 1 Multiple function combination cable eet refer to the aa sheet for detailed information No PortName Name Function Function Connection Note 0 Connection woe 7 o Network port n Connect to standard Ethernet cable Ca DC12V Ee DER Power input port Input DC 12V 2 2 Framework and Dimension Please refer to the following two figures for dimension information The unit is mm See Figure 2 2 and Figure 2 3 Figure 2 2 Dimension illustration 1 146 8 Figure 2 3 Dimension illustration 2 10 3 Device Installation Important Please make sure t
4. device list interface you can view device IP address port number subnet mask default gateway MAC address and etc Device List SR IP Address Port 1 Subnet Mask Default Gateway Mac Address 1 192 168 1 108 3TTTT 255 255 255 0 192 168 1 1 90 02 a9 7b 50 al m gt Tip You can click login button directly and then input corresponding information to login faa EN Upgrade Refresh Login Logout Figure 4 1 Search interface Select one IP address and then right click mouse you can see an interface is shown as in Figure 4 2 Select the Open Device Web item you can go to the corresponding web login interface Device List SN IP Address IECH lt f We Tip You can click login button directly and then input corresponding information to login Ju si Upgrade Refresh Login Logout Figure 4 2 Search interface 2 13 If you want to modify the device IP address without logging in the device web interface you can go to the configuration tool main interface to set In the configuration tool search interface Figure 4 1 please select a device IP address and then double click it to open the login interface Or you can select an IP address and then click the Login button to go to the login interface See Figure 4 3 In Figure 4 3 you can view device IP address user name password and port Please modify the corresponding information to login Please note the port informa
5. water leakage The glass front cap has sustained heavy push or strike The waterproof plug of the rear cap becomes loosen Do not use the proper supplying power The IR light can not turn on completely The object is out of the IR distance range of current device IR CUT does not turn to the night mode The photosensitive chip of the front end can not sense the IR light I can not upgrade the device via network When network upgrade operation failed you can use port 3800 to continue upgrade I can not login the client end or the WEB For Windows OS 98 or Windows ME user if you can not install the client end or can not view after the installation We recommend the win2000sp4 OS or install the client end of the low version The Active X control is blocked The display card version shall be dx8 1 or higher Network connection error occurred Invalid network setup Invalid user name or password I can not play the download file To guarantee setup update Power adapter There is no player There is no DX8 1 or higher For the MEDIA PLAYER there shall be Div X503Bundle exe plugin if you play the AVI file For Windows XP user you need to install the plugin DivX503Bundle exe and ffdsho 2004 1012 exe After you modified the important setup please reboot the device via the software to make sure the setup has been updated to the storage medium The general power adapter can work ranging from 0
6. C to 40 C The device may result in unstable power supply when the temperature exceeds the working temperature Please replace an industry level power adapter if you are using in the harsh environments 18 Appendix Toxic or Hazardous Materials or Elements Toxic or Hazardous Materials or Elements Component Name Pb Hg Cd Cr VI PBB PBDE Circuit Board E A 5 2 e S Component Device Case o o o o o o Wire and Cable o o o o o o Packing x i S J WR 5 Components Accessories o o o o o o O Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is below the relevant threshold of the SJ T11363 2006 standard X Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ T11363 2006 standard During the environmental friendly use period EFUP period the toxic or hazardous substance or elements contained in products will not leak or mutate so that the use of these substances or elements will not result in any severe environmental pollution any bodily injury or damage to any assets The consumer is not authorized to process such kind of substances or elements please return to the corresponding local authorities to process according to your local government statutes Note This user s manual is for reference only Slight difference may be found in
7. Cost effective HD IR Waterproof Fixed Network Camera User s Manual Version 4 0 0 Welcome Thank you for purchasing our network camera This user s manual is designed to be a reference tool for your system Please read the following safeguard and warnings carefully before you use this series product Please keep this user s manual well for future reference Important Safeguards and Warnings 1 Electrical safety All installation and operation here should conform to your local electrical safety codes The power shall conform to the requirement in the SELV Safety Extra Low Voltage and the Limited power source is rated 12V DC in the IEC60950 1 Refer to general introduction Please note Do not connect these two power supplying sources to the device at the same time it may result in device damage We assume no liability or responsibility for all the fires or electrical shock caused by improper handling or installation We are not liable for any problems caused by unauthorized modification or attempted repair 2 Transportation security Heavy stress violent vibration or water splash are not allowed during transportation storage and installation 3 Installation Do not apply power to the camera before completing installation Please install the proper power cut off device during the installation connection Always follow the instruction guide the manufacturer recommended 4 Qualified engineers needed All the exam
8. eneral type Encode H 264B mode Resolution CIF 352 288 352 240 Frame Rate PAL 25 S FPS NTSC 30 Stream Bit Rate Type CBR Recommend 192 1024Kb S ed Bit Bit Rate 512 Frame PAL 50 interval NTSC 60 SE Genera ype Image Size 720P 1280 720 SE Quality Better Bit Rate Main stream Interval 1s Privacy Mask Disable Video Overlay Channel Title Enable Setup YIOMION Default Setup Hem IPC HFW2100 Series Time Title Enable Snapshot C PictureDownload Path Path Record Path C RecordDownload Host Name IPC Ethernet Card Wire Default Mode Static Device MAC address when it is shipped out of the Mac Address factory IP Version IPV4 IP Address 192 168 1 108 Subnet Mask 255 255 255 0 Default TCP IP Gateway 192 168 1 1 Preferred DNS 8 8 8 8 Alternate DNS 8 8 8 8 Enable ARP Ping set device IP Enable address service Max Connection 19 TCP Port 37777 UDP Port 37778 Connection HTTP Port 80 RTSP Port 554 HTTPs On Disable HTTPs Port 443 Enable Disable PPPoE Username none Password N A Server Type Disable CN99 DDNS Server Address www 3322 0rg DDNS Domain in Name Username none Password ie Setup Item IP Filter SMTP Email UPnP SNMP Bonjour Main Stream Multicast Extra Stream IEEE802 Default Setup IPC HFW2100 Series Oe 10 minutes Trusted Sites Disable SMTP Server none Port 25 Anonymity Di
9. he installation surface can min support the 3X weight of the camera and the bracket Please follow the steps listed below to install the device Please refer to Figure 3 1 and Figure 3 2 for reference Paste the installation map on the surface of the wall or the ceiling Dig the installation holes according to the installation map Open the accessories bag and then take the expansion bolt out Insert the expansion bolt into the installation holes Take the screws from the accessories bag and then use them to secure the device on the installation surface of the wall or the ceiling Connect the corresponding cables No Name IPC Unit Installation Screw Installation Map Ceiling or Wall i Zi 3 Expansion Bolt H 5 Figure 3 1 Device installation illustration 1 Use the cross head screwdriver to loosen the adjust screw Turn the device in different directions to make it suitable for the monitor position Use the cross head screwdriver to fix the adjust screw firmly 11 Figure 3 2 Device installation illustration 2 4 Quick Configuration Tool 4 1 Overview Quick configuration tool can search current IP address modify IP address At the same time you can use it to upgrade the device Please note the tool only applies to the IP addresses in the same segment 4 2 Operation Double click the ConfigTools exe icon you can see an interface is shown as in Figure 4 1 In the
10. ination and repair work should be done by the qualified service engineers We are not liable for any problems caused by unauthorized modifications or attempted repair 5 Environment This series network camera should be installed in a cool dry place away from direct sunlight inflammable explosive substances and etc Please keep it away from the electromagnetic radiation object and environment Please make sure the CCD CMOS component is out of the radiation of the laser beam device Otherwise it may result in CCD CMOS optical component damage Please keep the sound ventilation Do not allow the water and other liquid falling into the camera Thunder proof device is recommended to be adopted to better prevent thunder The grounding studs of the product are recommended to be grounded to further enhance the reliability of the camera 6 Daily Maintenance Please shut down the device and then unplug the power cable before you begin daily maintenance work il Do not touch the CCD CMOS optic component You can use the blower to clean the dust on the lens surface Always use the dry soft cloth to clean the device If there is too much dust please use the water to dilute the mild detergent first and then use it to clean the device Finally use the dry cloth to clean the device Please put the dustproof cap to protect the CCD CMOS component when you do not use the camera Dome enclosure is the optical component do not touch the enclos
11. network directly without any auxiliary device This series network camera uses standard H 264 video compression technology which maximally guarantees the video quality It supports the IR night vision function In the night environments the device can use the IR light to highlight the object which is suitable for the surveillance function in the low illumination environments The waterproof design conforms to the IP 66 level It has the sound waterproof function suitable for use in the outdoor environments It can be used alone or used in a network area When it is used lonely you can connect it to the network and then use a network client end Due to its multiple functions and various uses this series network camera is widely used in many environments such office bank road monitor and etc 1 2 Features User Different user rights for each group one user belongs to one group The user right shall not exceed the group right Management Support central server backup function in accordance with your configuration Storage and setup in alarm or schedule setting l l Support record via Web and the recorded file are storage in the client end Function Support network storage function such as FTP Network camera supports one channel video data transmit to network terminal and then decode Delaying time is within 270ms network bandwidth support needed ce Max supports 20 connections Adopt the following
12. sable Username anonymity Password Se Sender none ES SEH Title IPC Message Attachment Enable Mail Receiver N A Interval 0 Second Health Mail Disable interval 60 Seconds Enable UPnP Disable SNMP Port 161 es ial publie SC prato Trap Address N A Trap Port 162 SNMP vi Disable SNMP v2 Disable SNMP v3 Disable Enable Enable Server Name SN It depends on the device Enable Enable Multicast Address 239 255 42 42 Port 36666 Enable Disable Multicast Address 239 255 42 42 Port 36667 Enable Disable Setup TELE ofge oe Hem QoS lt Qa D Motion Detect CH Video Masking gt oO 3 Disconnection 3 lt IP Conflict no O Ed Holiday Schedule D CO D H v D FTP Record Control Authenticatio n Default Setup IPC HFW2100 Series PEAP Username None Password Kees Real time 0 Monitor Command 0 Enable Disable Anti dither 5 seconds Record Enable Record Delay 10 seconds Send Email Disable Snapshot Disable Enable Disable Channel Enable Record Delay 10 seconds Send Email Disable Snapshot Disable Enable Disable Record Enable Record Delay 10 seconds Enable Disable Record Enable Record Delay 10 seconds Record Disable Snapshot Disable Enable Disable Address JWA Port 21 User Name anonymity Password N A Directory ee Pack
13. stics log and software version Image Sensor 1 3 inch CMOS Pixel 1280 H 960 V Day Night Support color to black Gain Control Fixed Auto White Balance Manual Auto BLC Exposure Mode Video Compression Standard Video Rate Frame Video Bit Rate Off BLC WDR 1 100 HLC anti flicker is outdoor and is valid only when exposure mode is auto with range 1 100 Manual Auto PAL It ranges from 1 3 to 1 10000 NTSC It ranges from 1 4 to 1 10000 H 264 H 264H H264B MJPEG PAL Main stream 1280 960 15fps extra stream 352 288 15fps Main stream 1280 720 25fps extra stream 352 288 25fps NTSC Main stream 1280 960 15fps extra stream 352 240 15fps Main stream 1280 720 30fps extra stream 352 240 30fps H 264 56Kbps 6144Kbps H 264H 16Kbps 6144Kbps H 264B 56Kbps 6144Kbps MJPEG is adjustable and bit rate is adjustable Support customized setup Support mirror So ally Support flip function Snapshot Max 1f s snapshot File extension name is JPEG Privacy Mask Supports max 4 privacy mask zones Video Setup Support parameter setup such as bright contrast GE Channel title time title motion detect camera masking Lens 3 6mm 6mm 8mm Fixed focus Lens Interface M12 Lens is the default accessories JO OWILIL B19U95 396 18 22 detection zones sensitivity level ranges from 0 to 100 Motion Detect area threshold ranges from 0
14. tion here shall be identical with the port value you set in TCP port in Web Network interface Otherwise you cannot login the device If you are using device background upgrade port 3800 to login other setups are all invalid IP Address 192 168 1 108 User Name oto Password Port 37777 Figure 4 3 Login prompt After you logged in the configuration tool main interface is shown as below See Figure 4 4 NetWork Parameter PPPOE System Information System Upgrade General Parameter DHCP Enable lipv4 IP Address 192 168 1 108 Subnet Mask 255 255 0 0 Gateway fio 15 0 1 Mac Address 90 02 a9 7f d8 21 Figure 4 4 Main interface For detailed information and operation instruction of the quick configuration tool please refer to the Quick Configuration Tool User s Manual included in the resources CD 14 5 Web Operation This series network camera products support the Web access and management via PC Web includes several modules Monitor channel preview system configuration alarm and etc 5 1 Network Connection Please follow the steps listed below for network connection Make sure the network camera has connected to the network properly Please set the IP address subnet mask and gateway of the PC and the network camera respectively Network camera default IP address is 192 168 1 108 Subnet mask is 255 255 255 0 Gateway is 192 168 1 1 Use order ping
15. ure when you are installing the device or clean the enclosure when you are doing maintenance work Please use professional optical clean method to clean the enclosure Improper enclosure clean method such as use cloth may result in poor IR effect of camera with IR function 7 Accessories Be sure to use all the accessories recommended by manufacturer Before installation please open the package and check all the components are included Contact your local retailer ASAP if something is broken in your package Accessory Name Amount Network Camera Unit 1 Quick Start Guide 1 CD 1 Installation Accessories Bag 1 ill Table of Contents Mis CRS eI HE eege 1 1 1 OVCE Wesa e EE E E 1 1 2 POAC eh eege eege eren eege ii alii ai 1 1 3 Specificato NS ae an oak ege ee 2 1 4 Factory Default Setup SE 3 i Ee 9 2 1 Multiple function Combination Cable 9 2 2 Framework and Dimension EE 9 o ee TE E e aaa 11 4 Quick Configuration Ee 13 4 1 TEEN ante a ee we ee Sener Er en ar eege Pe DI dala DIA Dir iii pra rie cre rere eee er adi 13 4 2 Kee eet eet 13 bc Web le EE 15 5 1 Network Connection EE 15 5 2 Login and Main Interface 15 B FAQ RE 18 Appendix Toxic or Hazardous Materials or Elements 19 1 General Introduction 1 1 Overview This series network camera integrates the traditional camera and network video technology It adopts video data collection transmission together It can connect to the
16. user interface All the designs and software here are subject to change without prior written notice All trademarks and registered trademarks mentioned are the properties of their respective owners If there is any uncertainty or controversy please refer to the final explanation of us Please visit our website for more information 19
17. video transmission protocol HTTP TCP UDP MULTICAST RTP RTCP RTSP and etc Support web access Network Realize network camera configuration and management via Ethernet Management Support device management via web or client end External power adapter DC 12V Support PoE Power Warning Do not connect these two power supplying sources to the device at the same time it may result in device damage Log function Support system resource information and running status real time display Day Night mode auto switch Assistant Support picture parameter setup such as electronic shutter and gain setup Function Support motion detect Backlight compensation screen auto split to realize backlight compensation to adjust the bright Support video watermark function to avoid vicious video modification Built in IR light Support IR night vision The enclosure conforms to the IP 66 protection Has the waterproof function 1 3 Specifications Please refer to the following sheet for network camera performance specification Model Parameter w S S 49 QWEJEd 0 PIA Main Processor IPC HFW2100 Series TI Davinci high performance DSP OS Embedded LINUX System Resources Support real time network local record and remote operation at the same time User Interface Remote operation interface such as WEB DSS PSS System Status Bit stream stati
Download Pdf Manuals
Related Search