User Manual - VOIP GSM Gateways
Contents
1. Aout Tx GND PTTIN CN CP EN EE lm d PTT Adapter Cable Wiring Diagram Jl ET11 6P6C ADJOUT VOUT GND VIN GND ETTOUT 6 pin RJ 11 Plug e Remote Control Wiring Diagram The SWITCH port is a RJ 11 socket with the middle two pins connected to a relay switch It functions as an ON OFF switch for controlling an external device or system www hvbertone com ROIP102 User Manual Setting up the Main Unit RolP 102 i Connect the SWITCH Port to an external system for remote ON OFF control If the relay switch is connected to high voltage load The maximum rating for the internal relay is 500mA 240VAC load current Power Adapter ii Connect the Channel Port to a Radio via the PPT Adapter Cable provided Connect to a PC or Local Ethernet Connect Network to an external Connect to a Router system for Network Switch remote ADSL Cable Modem ON OFF to access external Network iii Connect the WAN Port to a router network switch ADSL Cable Modem for external public network access conrol iv Connect the LAN Port to a local PC or a local Ethernet network LAN This allows the local network to access the external network via the WAN port However this LAN port is intended for device configuration low data traffics applications High data traffics through this port may affect the RolP102 performance 5 Factory Default Settings The table below shows the factory default se2. In the LAN port configuration shown below select Static IP and then fill in the parameters as provided by your network administrator 2 DHCP When the device is installed behind NAT and a DHCP host is available select this mode will enable the device to obtain LAN IP address and other network IPs automatically 3 PPPoE For most ADSL and Cable modem access method the PPPoE dial up is normally used If the RoIP is connected directly to an access LAN Port PPPOE le modem you may need to select the PPPoE Please consult your ISP for further UserName information if needed Fill in the User password fo Name and Password as provided by your ISP to complete this LAN port configuration Another network device can be connected to the PC PC Port StaicIP Le port It offers both Bridge and Static IP modes to meet jp Address 192 168 8 4 your requirements The factory preset is Static IP mode _ with the IP address 192 168 8 1 subnet Mask 299 299 299 0 DHCP Server Enable Disable 1 Bridge Mode Select Bridge mode if your network topology requires the network devices PC or others to be in the same Ending Address 192 1688 120 network segment In this case the device functions 24 DNS optional IT as an Ethernet Switch as well Starting Address 192 168 8 100 PC Port Bridge mode Static IP www hybertone com ROIP102 User Manual 2 Static IP Mode Default Setting Select Stati
3. allows a user to access the RolP s webpage directly from our remote control server www hybertone com ROIP102 User Manual 6 3 2 Network The performance of RolP102 depends greatly on the network bandwidth available Proper network environment is the key to insure RoIP102 for optimal performance High bandwidth leased line network with static public IP is the most preferred network environment for RolP operation Shared network with dynamic public IP assignment PPPoE like ADSL Cable modem router connection is relatively unstable RolP operation is interrupted when link re establishment occurs since the dynamic IP may be changed to a different IP In addition the router gateway in this network environment is required to configure DMZ mode with its IP set to the WAN IP of the Rol P Before configuring the Network settings please first get details of the current network environment In principle it is recommended to use a public IP for the WAN port of the RolP However there are 3 choices for the WAN port setting as described below Network Configuration LAN Port Static IP M PC Port static IP M IP Address IPAddress 192 168 8 1 Subnet Mask Subnet Mask 255 255 255 0 optional Default Route Po DHCP Server Enable Disable Primary DNS Starting Address 192168 8 100 Secondary DNS D E Ending Address 192 166 8 120 optional S S 1 Static IP This mode applies to both public and private IP network environment
4. cellular phone network Its operation and performance rely on the broadband network connections via private and or public networks and the cellular phone networks Due to the stability and reliability of these networks this product may not be able to link up all the networks connected without any interruptions Therefore it is not recommended to use this product in an emergency system or a communication system with zero failure This product can bridge and extend radio networks all over the world Please consult your local regulations in order to use this product legally This product requires the use of dynamic DNS DDNS service For testing purpose this DDNS service is temporary provided free of charge by Hybertone Technology Hong Kong However this service is not guaranteed without any interruptions Customers are urged to build their own DDNS server or obtain this service from a DDNS provider Free DDNS server software may be obtained freely from your local network service provider Customers and or users are taking full responsibilities and all risks in using this product We are not responsible for any direct or indirect losses caused by but not limited to communication failures as a result of product failure or network problems CUSTOMERS ARE ASSUMED TO HAVE READ AND ACCEPTED WITH FULL UNDERSTANDINGS OF THE IMPORTANT NOTICES STATED ABOVE www hybertone com ROIP102 User Manual 2 Out of the Box Check List Upon unpacking th
5. ready to use Just push the PTT button at one radio terminal voice is transmitted to the other radio terminal automatically If the volume level is not correct please adjust the 2K Potentiometer located at the PTT Interface adapter cable www hybertone com ROIP102 User Manual 7 Specifications Core Design CPU ARM9 RAM 16MB FLASH 4MB DSP 116MHz 16 Bit Bus Firmware WN Linux version 2 6 Network Protocols IP TCP UDP HTTP ICMP DHCP CLIENT amp SERVER NTP TFTP ToS DDNS Telnet SIP v 2 HTML XML2 0 JAVA G 711 a law amp u law G 729A G 729AB G 723 1 GSM Physical amp Operation Conditions 12VDC 500mA 10 100 Base T 10 100 Base T 220VAC input and 500 mA load current VoIP Protocol Configuration GUI Codecs Power Supply WAN Port LAN Port SWITCH Relay 10cm x 6 8cm x 2 5cm 100 g Storage Temperature 40 C 80 C 0 C 40 C Dimension Weight main unit Operating Temperature room PTT Interface PTTIN Active Low lt 0 7V 4 7KQ load PTTIN Active High gt 1 2V PTTOUT High Output 5V 4 7 KQ load PTTOUT Low Output OV SO 750mW 5V P P 6000 Internal Impedance 0 0 6Vp t p Aout gt 5 2KQ Potentiometer ADJOUT on the Adapter Cable PTTIN Circuit Q5 Roo 47K V GND Based on the circuit above the PPT Input level is high when it is open ended www hybertone com ROIP102 User Manual PTTOUT Circuit 107 PTT
6. OUTI www hybertone com
7. P Number as 101 8 Go to the Preference Page and enable the DDNS Enable Disable DDNS feature If the serial number of the DDNS Address RolP102 is R10210120099 then its DDNS address is R10210120099 com DDNS Port Update Interval sgol www hybertone com ROIP102 User Manual 9 10 Next go to Call Settings page and configure it as shown below Call Settings Group 1 Advanced a S T Media Settings gt gt SIP Proxy Register Expiry s AuthenticationID Auto Dial Number ss For Codec Settings choose a law or u law for best voice performance Please make sure that both RoIP102s are using the same codec Group Codec Settings Group 1 Codec g 29 7 11 Next configure the RolP102 at location B as described above with the exception of call settings 12 Configure the Call Settings page of the RolP at location B as follows Please note that it has a different Group SIP Number as the one in location A Please note that the SIP Proxy address is set to the DDNS address of the RolP102 at location A The Auto Dial Number is set to the Group SIP Number of the one at location This means that 102 calls 101 automatically whenever the PTT control is active transmitting voice from 102 to 101 Call Settings Group 1 Advanced Group SIP Number Media Settings gt gt SIP Proxy Register Expiry s 300 AuthenticationID Auto Dial Number 13 At last the two RolPs are setup and
8. ROIP102 User Manual Cross Network Gateway Radio VOIP Public Announce User Manual Model ROIP102 Version 1 0 2011 07 13 To save the environment please view this manual electronically and only print the pages as required www hybertone com ROIP102 User Manual Contents BN e ie ele gint Led Le 3 2 COUT ORCAS BOX CS A AIS en es he a nn 4 OV eee eee oe ne ee ee ee eee eer ee ee 5 gt a let eeh OCU Oy oars ae src eee D bee nd eee 5 3 2 Typical Application TODO ORY E 6 3 3 MOGELINOMENClA EURE ne a annee eee en eric ie tes aie ni 6 Aa A Ce E d e E a a et te ie le oo a ei 6 Se OC ON De A ES SE suaceneinavecseaeaaneseienceseae A 8 6 Device Configuration Via Built in Web Server 9 6 1 WED EEr LOE Mereeee error E Eco Meo oer ee ere ne re ere eee eee ne 9 6 2 Eed 9 6 3 COMBO a a eee ee 10 OS LE PPS a a a ae A 10 Dis INS NOR ee a a E ese tes E E E A T 11 ZK CS gn 12 Ee E PET E a 13 Caa p 618 0 gel EE 14 SE E E ee e ge E gl E 14 Sere GROUP COUSCOUS a 14 OS SNS CS ne ee ene ee eee ee eee eee 14 6 4 TOO E 15 GR OnE DEAR a et uen ent ee tete na ae eee 15 fe ey CEE PASS e nee ete bee ete ne ae tete ed ae cn 15 6A RSC OO eee E E E ata eemacenu cems 15 OR D ele a en ae a a de dit 15 6 5 EREECHEN 15 KEE 9 19111 6 2 ge a ee ere ace err ee eee 18 www hybertone com ROIP102 User Manual 1 1 2 4 Important Notices This product is used to link up the civilian radio networks internet and
9. TT Input for Rx and Output for Tx Difference radio terminals may have different requirement on the PTT control signals Please consult the User Manual of your radio terminal for more information 1 Input Active Level defines the active level for the PTT Input Select 1 if the PTT Input is active when the electrical level is high 5V Select 0 if the PTT Input is active when the electrical level is low OV 2 Output Active Level defines the active level for the PTT Output Select 1 if the PTT Output is active when the electrical level is high 5V Select O if the PTT Output is active when the electrical level is low OV 3 PTT Output Expiry s defines the maximum duration in second for the PTT Output to be active This means that the maximum transmit time for a voice channel is limited by the PTT Output Expiry This method is used to prevent a radio terminal to occupy the voice channel indefinitely The minimum value is 30 www hybertone com ROIP102 User Manual 6 3 5 Recorder Settings The recording settings define the address of the recording server Please refer to the RolP Voice Recording User Manual for more information Recorder Settings Group 1 6 3 6 Broadcasting Settings Broadcasting Settings PS OR Password Expiry Lr Password The RolP102 provides a relay switch output to control an external system for broadcasting or other applications A radio user in the group can
10. c IP mode for a new network segment on PC port The device now becomes a network router as well Enter an IP address PC Port Static IP in IP Address field with a new segment address mp Address that is different from the one used in the LAN port Enter the subnet mask in Subnet Mask uPnet Mask 295 299 255 0 field accordingly A commonly used value is 255 255 255 0 Enable the DHCP Server to set the device as a DHCP Server Enable Disable DHCP host to assign IP Addresses to network Starting Address 192 168 8 100 devices that are attached to this new network segment Ending Address 192 168 8 120 Static DNS optional ____ Specify the Starting Address Ending Address and Static DNS accordingly 6 3 3 Call Settings Group 1 Advanced gt Group SIP Number _ Media Settings gt gt Register Expiry s 300 AuthenticationID Password fs Auto Dial Number In order for RolPs to communicate with each other they need to know their IPs and group relationship This can be achieved via the following two methods 1 An external SIP Server In this configuration each RolP registers to the SIP Server which handle all communications among all RolPs registered Commands are sent to the SIP Server for processing and then relay to the designated device Please program the call setting parameters as described below Group SIP Number the SIP number created in the SIP Server for this R
11. control this relay switch by dialing DTMF digits on the dialing keypad When the Broadcasting On Password DTMF Tones is received in the audio stream the relay switch is turn on When the Broadcasting Off Password is received the relay switch is turned off The Broadcasting On Expiry is used to prevent the relay switch from being turned on indefinitely When the turn duration reaches the Expiry time the relay switch is shut off automatically 6 3 7 Group Codec Settings Group Codec Settings Group 1 Codec g729 Voice codec is commonly used in voice over IP communications It enables voice to be compressed in order to save the transmission bandwidth The higher the compression rate is the low the transmission bandwidth is required However the voice quality is degraded as the compression rate goes higher In general a law u law and G 729 are commonly used The transmission rate of a single voice channel is about 82Kbps for a law or u law and about 26Kbps for G 729 However when a radio station is required to transmit voice data only a law or u law codec should be selected to minimize the loss in voice quality It is important to note that all users in the group must use the same codec 6 3 8 Save Changes To save all changes made click on Save Changes icon on the left panel The web server will not remind you to save changes when you exit www hybertone com ROIP102 User Manual 6 4 Tools The Tools menu offe
12. e admin for the 55e connection login user name and admin for the password ILE E Please make sure to save the configurations click E Remember my password on Save Changes after configuring the device o 1 ce 6 2 Status This is the default page when you first login to the device web server It consists of three columns and it is important to understand the information shown in this page in order to debug or report a device problem Status Status Phone Information Network Information Configurations Serial Number R10210120099 Lan Port 192 168 2 139 Firmware Version RolP 1 01 18 Lan MAC 00 11 BE 03 DC 30 Tools Hardware Version RolP 1 PC Port 192 168 8 1 Group 1 Status LOGOUT PPPoE Disabled Default Route 192 168 2 1 DNS Server 210 0 128 250 www hybertone com ROIP102 User Manual 6 3 Configuration The page contains all configuration settings for the RolP It is subdivided into various sections pages for the ease of configuration The sub pages include Preference Network Call Settings PTT Settings GSM Settings Recorder Settings Broadcasting Settings Group Codec Settings and Group Settings 6 3 1 Preference The Preference page consists of the common settings for the device and is shown below Preference Language English M Auto Reboot Time Zone GMT 8 Reboot Time 04 00 Time Server DONS DONS Address voipddns net DDNS Port Update Interval 600 Re
13. e RolP102 package please check the content carefully against the list below Please report immediately to the supplier for any missing items amp 7 1 x AC DC Adapter Input 110 220VAC Output 12VDC 500mA 3 x PTT Adapter Cables 1 x Ethernet Cable www hybertone com ROIP102 User Manual 3 Overview The fundamental of RolP Radio over IP technology is to convert the audio and PTT signals in a radio terminal into IP packets and then transmit the data via the IP networks The challenge in this technology is to insure that the audio is transmitted in real time and the PPT control signal is securely transmitted The radio range is general limited by the restricted transmitting power the antenna sensitivity and other environmental factors The successful deployment of this technology extends the coverage of a radio network without using expensive repeaters by linking up multiple radio networks in the world In addition this technology can also link up the radio networks to the VoIP networks and the cellular networks It truly makes voice communications across multiple networks possible RolP102 series Cross Network Gateway is designed as a compact and practical device to bridge voice communication between Radio and VoIP networks only It comes with one standard PTT port for interfacing with only one Radio network No GSM module is embedded for GSM termination It simply converts voice signals from a Radio terminal to IP packets and the
14. erface of the radio terminal GM300 with the PTT Interface Cable as shown in the diagram below Connect the RJ 11 plug of the PTT Interface Cable to the PTT port 2K Potentiometer RARE RE PTTout GND GND PTT Interface Cable PTT Interface Cable with Radio Terminal 2 Connect the RolP102 LAN port to an Ethernet port of the ADSL Router 3 Assign a fixed IP to the RolP102 LAN port This fixed IP must be in the same segment as the LAN port of the ADSL Router For example if the LAN of the ADSL Router has an IP 192 168 1 1 then the LAN port RolP102 could be set to 192 168 1 101 4 Configure the DMZ mode of the ADSL Router to fixed IP assigned to the RolP302 LAN port For DMZ configuration please refer to the User Manual of your Router 5 Login to the RolP Webpage and program the Network Settings as shown below Please note that the DNS addresses should be programmed as provided by from your local ISP Network Configuration LAN Port PC Port IP Address IP Address aa 265 255 266 0 Subnet Mask 255 255 255 0 Default Route 192 168 1 1 DHCP Server Enable Disable Primary DNS 202 96 134 133 Starting Address 192 168 8 100 Secondary DNS IT Ending Address 192 166 8 120 optional a Static DNS optiona ne er page and set both PTT wpm Input and Output to MputActive Level 0 x active low as shown Hihi Level 0 PRE N below 7 Assign the RolP102 at Location A to be the Host with the Group SI
15. mote Control lt Remote Serer fs Remote Server Port Po Remote Server ID fs Remote Server Key fs The mains settings in this page include 1 Language This specifies the language for the webpage and the voice prompts Currently only English and Simplified Chinese are supported Time Zone and Time Server Time Zone is specified as GMT or a fixed value RolP acquires the standard GMT time from the Time Server specified Auto Reboot This option reboots the device automatically at the time specified DDNS When the RolP is installed in a network environment with dynamic public IP and a SIP DONS Enable Disable server is not used customer can choose to Use DDNS Address our free DDNS service or DDNS offered by other ee DDNS Port 39980 service provider Enable this option to connect to our DDNS service as shown on the right The Update Interval 600 current settings are set to connect to our DDNS server voipddns net using port 39980 and the update time is 600 seconds Please note that the DDNS Address cannot be set to other DDNS server this setting only works with our own DDNS server Once this service is used the DDNS address for the RolP is then lt serial number gt com The serial number is shown on the bottom label For example if the serial number of the device is R10210120099 then the DDNS address of this device is R10210120099 com Remote Control This option
16. n communicates with a host RolP302 to form a group with multiple networks as shown in the Basic Network Configuration below In addition the built in relay enables RolP102 to function as a remote control switch User can control the built in relay to switch on or off devices such as an alarm a light a public announce system an electronic lock etc To simplify network setup and configuration a DDNS client is implemented in RoIP102 to resolve the issue of dynamic public IP addresses with most home and some office network connections 3 1 Theory of Operation The diagram below shows the concept of how RolP bridges the voice communications between two radio terminals at two different locations At each location a radio terminal is connected to a RolP via the PTT Interface Cable provided Tx is the transmitted audio signal and Rx is the received audio signal Please note that the Tx signal at RolP terminal is connected to the Rx signal at radio terminal and vice versa for the Rx signal at RoIP terminal The PTT signals are the control signal for transmitting and receiving audio signals and they should be connected as shown below The two RolPs are connected via internet or intranet in order to create a virtual connection between the two radio terminals PTT PTT Interface Interface Cable Wirtual Cable Connections E PTTin PTT PT Tout GND GND Radio Terminal PTT Interface Radio Terminal PTT Interface Network Con
17. nection Wia Intranet or Internet E RolP302M Gs RolP102 Location Location B www hvbertone com ROIP102 User Manual 3 2 Typical Application Topology The network diagram below shows a basic topology for interconnecting radio terminals at multiple locations A ROIP302M is used at location A as a centralized point of the interconnection ROIP102 is used at the other three locations to interface with the local radio terminal and interconnect with the ROIP302M at location A Radio terminals at these two locations now are interconnected User in any one of the radio channel can now talk with users at in the other three channels RolP320GM H Location pu L INTERNET 2 RolP102 eg R Location D WA K RolP102 re Location B Ze Sa Se x reneeeaeeaneegeeggtff 3 3 Model Nomenclature RoIP 102 Model Name PTTx1 RJ45 x 2 4 Installation a Back Panel CT Es LI www hvbertone com ROIP102 User Manual CHANNEL 6 pin RJ11port for PTT Adapter Cable 2 SWITCH Remote control Relay switch 220VAC input and 500 mA load current access access POWER 12VDC 500mA b LED Indicators LED Label RUN Device status Not connected to RolP302M when flashing at 4 times sec fast jp Connected to RolP302M when flashing at twice per seconds slow c Channel Port Pin Assignment The channel port is a 6 pin RJ 11 Socket PTTOUT GND Vin Rx
18. olP SIP Proxy IP address or Domain address of the external SIP Server Authentication ID the SIP login ID usually this is the same as the SIP Number Password the login password for the SIP login ID VV VV Y Auto Dial Number the Group SIP Number for the RolP to dial when establishing a call connection 2 Peer to Peer Connection In this configuration any one of the RolPs can be a Host which allows other RolPs to register to The host needs to registers to itself as well Each device www hybertone com ROIP102 User Manual needs to have an unique number as an identification for communicating with each other The table below shows the parameter settings for both Host and Terminal configurations Calling Settings for Peer to Peer Configuration Group SIP Number an unique number assigned an unique number assigned arbitrary for RolP identification SIP Proxy Host IP address or DDNS Host IP or DDNS address if address if enabled Authentication ID Blank Not Required Blank Not Required Blank Not Required Blank Not Required Auto Dial Number Blank Not Required Designated RolP Group SIP Number for establishing a voice connection pressing the PTT control for voice transmit 6 3 4 PTT Settings PTT Settings PTT Input Active Level 0 Output Active Level D e PTT Output Expiry s 60 This section defines the PPT Signal settings RolP102 supports only one PTT port which consists of two control signal P
19. rs the following utilities Online Upgrade Change Password Reset Config and Reboot 6 4 1 Online Upgrade Please check regularly with your supplier or our website for the latest firmware release Copy the upgrade link address to the Upgrade Site and then click Start to begin firmware upgrade Please make sure that the power is not interrupted during firmware upgrade in order to avoid memory corruption If memory corruption occurs the RolP will fail to boot up and will need to return for repair Online Upgrade Last Upgrade Time 2010 07 23 11 36 06 Current Version RolP 1 01 15 Upgrade Site 118 142 51 162 update ROIP 1 01 15 pkg Start 6 4 2 Change Password The webpage login passwords for both admin and user IDs can be modified here Please make sure that you keep the new password securely If you lose the password you will need to reset the device to factory defaults by pressing the 6 4 3 Reset Config Click on the Reset Config Icon to restore the device to the factory default settings as described in section 5 6 4 4 Reboot Click on the Reboot icon will perform a device cold boot and this will takes a few minutes to complete 6 5 Application Example Environment 1 Linking up two MOTO GM300 Radio terminals 2 Using two RolP102s 3 Using PTP Connection 4 Using ADSL Router for Network Access www hybertone com ROIP102 User Manual Setup Procedures 1 Connect the PTT Int
20. ttings There are two ways to reset to the factory default settings i Press the RESET switch for more than 15 seconds ii Inthe Configuration page select Tools and then Reset Config Factory Default ee FE Login ID user Login Password admin 1234 Programmable eee characters in the ASCII table WAN Port Setting DHCP oO LAN Port Setting 192 16881 o PTT State 0 is active o is active low 1 is active high PTT maximum duration Less than 600 seconds Jitter Delay 60 milliseconds 20 220 milliseconds www hybertone com ROIP102 User Manual 6 Device Configuration Via Built in Web Server The built in web server provides a comprehensive way to configure the device manually 6 1 Web Server Login Follow the following procedures to access the RolP102 via the LAN port The WAN port is set to DHCP and its IP is obtained from a local DHCP host automatically It may not be convenient to find out its IP and it would be easier to access the webpage via the LAN port via the following procedures 1 Connect the LAN port of the RolP102 to a computer a local Ethernet network 2 Configure the computer IP to 192 168 8 x x 2 to 254 The server 192 168 2 139 at Please Login requires a username and password 3 Type 192 168 8 1 which is the factory preset IP for ER net da SETVET IS TE LUSemame an the RolP102 LAN port password be sent in an insecure on Dos ave 4 In the web login window typ
Download Pdf Manuals
Related Search