User`s Manual - Reliability Direct, Inc.
Contents
1. do not make any voltage measurements that exceed the maximum specified limits 1 Set the Function switch to the 400V AC position 2 Insert the test leads to the meter as follows Red lead to V terminal Black lead to the COM input 3 Connect the test leads to the circuit or device under test 4 Read the ACV value on the LCD DC Voltage Measurements WARNING To avoid electric shock or damage to the meter do not make any voltage measurements that exceed the maximum specified limits 1 Setthe Function switch to the 400V DC position 2 Insert the test leads to the meter as follows Red lead to V terminal Black lead to the COM input 3 Connect the test leads to the circuit or device under test 4 Read the DCV value on the LCD 4 Ver 1 6 03 2005 Advanced Features Relative Measurements 1 Press the ZERO key The displayed reading will zero and the word ZERO will appear on the upper portion of the LCD 2 All subsequent measurements will now be displayed with respect to the zeroed reading For example if a 20A reading is zeroed and a 30A reading is subsequently measured the LCD will display 10A 3 To return to normal operation press and hold the ZERO key for 2 seconds until the word ZERO switches off 4 Note that Relative mode is not available if MIN MAX mode is enabled Data Hold To freeze the current reading on the LCD press the Data Hold key The word HOLD will appear on the LCD while the meter is i2. EXTECH INSTRUCTION MANUAL INSTRUMENTS Model 380942 True RMS AC DC 30A Mini Clamp on Meter ZERO 400mA AC mwa C wi C MAXMIN HOLD AC DC mA CLAMP METER True RMS ZEROA HOLD MAX MIN a UU imi abra d a dad True RMS AC Current and Voltage Measure low current with high resolution to 0 1mA AC and 1mA DC Auto Power Off One touch DCA zero adjust MIN MAX and Data Hold functions 0 9 23mm Jaw diameter Introduction Congratulations on your purchase of Extech s DC AC Clamp Meter This professional meter with proper care will provide years of safe reliable service Specifications General Specifications Display 3 3 4 4000 count Digit LCD with 40 segment bargraph Functions ACA DCA ACV DCV Polarity Minus sign indicates negative polarity Current sensor Hall effect sensor type Overload indication Left blinking digit DCA zero adjust One touch zero key Display rate 2 readings second 20 readings second for bargraph Battery Two 1 5V AA batteries Operating conditions 4 F to 122 F 10 C to 50 C lt 85 Relative Humidity Storage conditions 4 F to 140 F 20 C to 60 C lt 75 Relative Humidity Altitude Operate at less than 2000 meters Indoor use only Power consumption Approximately 10mA DC Weight 6 2 oz 190g including ba
3. ffers repair and calibration services for the products we sell Extech also provides NIST certification for most products Call the Customer Service Department for information on calibration services available for this product Extech recommends that annual calibrations be performed to verify meter performance and accuracy Warranty EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for one year from date of shipment a six month limited warranty applies on sensors and cables If it should become necessary to return the instrument for service during or beyond the warranty period contact the Customer Service Department at 781 890 7440 ext 210 for authorization or visit our website at www extech com click on Contact Extech and go to Service Department to request an RA number A Return Authorization RA number must be issued before any product is returned to Extech The sender is responsible for shipping charges freight insurance and proper packaging to prevent damage in transit This warranty does not apply to defects resulting from action of the user such as misuse improper wiring operation outside of specification improper maintenance or repair or unauthorized modification Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable for any direct indirect incidental or consequential damages Extech s total l
4. iability is limited to repair or replacement of the product The warranty set forth above is inclusive and no other warranty whether written or oral is expressed or implied n ih Support Hotline 781 890 7440 Tech support Ext 200 Email support extech com Repair Returns Ext 210 Email repair extech com Website www extech com Copyright O 2003 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 6 Ver 1 6 03 2005
5. n the Data Hold mode To release the Data Hold function and return the meter to normal operation press the Data Hold key again The word HOLD will switch off MIN MAX Readings Pressing the MIN MAX key allows the meter to display the highest and then the lowest readings encountered Press the MIN MAX key once to view the minimum reading press it again to view the maximum reading Note that the meter will only change its displayed reading when a measurement is taken higher than the previous MAX or lower than the previous MIN readings The HOLD display icon along with the MIN or MAX icon will appear on the LCD in MIN MAX mode Pressing the MIN MAX key a 3 time returns the meter to normal operation Auto Power Off To extend battery life the meter will auto power off after 30 minutes of operation To resume operation either turn the meter OFF and then ON again or press the HOLD button To disable the auto power off function press down the HOLD key while turning the meter on 5 Ver 1 6 03 2005 Maintenance Battery Replacement 1 When the low battery symbol appears on the LCD the batteries must be replaced 2 3 4 Power down and remove the rear battery compartment Phillips screw Lift off the battery compartment cover and replace the two 1 5V AA cells Replace compartment cover and secure the screw Cleaning Caution Use only a dry cloth to clean the plastic case Calibration and Repair Services Extech o
6. ttery Dimensions 7 2 x 2 5 x 1 4 183 x 63 6 x 35 6mm HWD Jaw opening 0 9 28mm Standards IEC 1010 Category III 300V Category Il 600V Range Specifications Function Range Resolution Accuracy Overload protect DC Current 4000mA 1mA 2 0 3d 40A DC 30A 10mA 100A DC AC Current 50 60Hz 40 to 100Hz True RMS 400mA 0 1mA 1 5 5d 2 0 5d 40A AC 50 60Hz 40 to 1kHz 4000mA 1mA 2 5 5d 3 0 5d 40A AC 30A 10mA 2 0 5d 2 5 5d 100A AC DC Voltage 400V 0 1V 1 0 2d 1000V DC AC Voltage 50 60Hz 40 to 1kHz True RMS 400V 0 1V 1 5 4d 2 0 5d 800V AC Specification Notes AC Voltage and Current Crest Factor lt 3 AC DC Voltage Input Impedance 10MQ Ver 1 6 03 2005 Meter Description 1 Current sense jaw 6 One touch DCA ZERO key 2 Measurement Trigger 7 LCD Display 3 Function switch 8 Positive input terminal for V HZ and Q 4 Data HOLD key 9 COM terminal 5 MAX MIN key 1 2 345 6 7 Safety Symbols and Information N Caution Refer to the explanation in this Manual A Caution Risk of electric shock L Earth Ground This meter has been designed to be safe in use but the operator must use caution in its operation The rules listed below should be carefully followed for safe operation 1 NEVER apply voltage or current to the meter that exceeds the specified maxim
7. um 2 USE EXTREME CAUTION when working with high voltages 3 DO NOT measure voltage if the voltage on the COM input jack exceeds 600V above earth ground 4 ALWAYS turn off the power and disconnect the test leads before opening the back to replace the fuse or batteries 5 NEVER operate the meter unless the back cover and the battery fuse door are in place and fastened securely 3 Ver 1 6 03 2005 Operation AC Current Measurements True RMS WARNING To avoid electric shock disconnect the test leads from the meter before making current measurements 1 Set the Function switch to the 400mA 4000mA or 30A AC range 2 Press the jaw trigger and clamp around fully enclosing a single conductor Do not allow a gap between the two halves Yes of the jaw Refer to the diagram at right for the correct way to enclose a single conductor 3 Read the ACA value on the LCD No DC Current Measurements WARNING To avoid electric shock disconnect the test leads from the meter before making current measurements Set the Function switch to the mA or 30A DC range N Press the DCA zero key to null the meter display 99 Press the Trigger to open the current sense Jaw Fully enclose the conductor to be measured Do not allow a gap between the two halves of the jaw 5 Read the DCA value on the LCD A AC Voltage Measurements True RMS WARNING To avoid electric shock or damage to the meter
Download Pdf Manuals
Related Search