F-ZTAT Microcomputer On-Board Purge/Write Tool User`s Manual
Contents
1. 2 2 On Board Writing Tool Information Files The flash memory block information file and user write control program are needed to operate the on board writing tool To use an F ZTAT microcomputer that cannot be used with the provided information files create the flash memory block information file lt device name gt INF and an original user write control program lt device name gt SUB If the operating frequency differs from the default operating frequency of the provided information files a user write control program must also be newly created The same device name must be used for all information files to be created 2 2 1 Flash Memory Block Information Files device name gt INF The flash memory block information file is an ASCII file which specifies the flash memory area to write user data area to load the user write control program RAM emulation block and the corresponding registers Contents of the flash memory block information file for the H8 538F is shown in figure 2 4 To use the on board writing tool with a different device start and end addresses of each block must be edited For more details refer to the device s hardware manual Figure 2 4 Flash Memory Block Information File for the H8 538F HITACHI 7 2 2 2 User Write Control Program device name gt SUB The user write control program is a program that controls how user data that is transferred from the host computer with the on board writing tool2. Windows 95 operating system Microsoft WindowsNT operating system and MS DOS are registered trademarks of Microsoft Corporation in the United States and or other countries 3 IBM PC is a registered trademark of International Business Machines Corporation in the United States HITACHI i Contents eto DE eee 1 FPS ON 1 25 o O 1 1 3 Communication Parameters cccccccccssesssscceeceeeeeeeesessseccessessnseeeeeeeeeeeseseeseeeesseeeaaes 3 E RA breddene eselet 4 Section 2 Operation Pr cedutes iun uas a aie me 5 24 Installation See ak 5 2 2 On Board Writing Tool Information Files ooonnnccnonccinonocnonncnonncnonanonnnnonanccnonccnonaconnnos 7 2 2 1 Flash Memory Block Information Files device name gt INF 7 2 2 2 User Write Control Program device name gt SUB rrrnrrnnrrrnrnnrrnrnnrrrnrnnnnnrr 8 2 2 3 User Write Control Program Source File device name SRC 8 2 3 Installing the On Board Writing Tool sooronvrnonnrnnenrrvnvenenvnrnrrnrnnenvnnenvanenvrnsvensnnnresensene 10 2 4 Selecting the Program Mode esnnrerenvnnenvanennrnrnrnnenvanenvnnenvrnssnrerenranenennenvrnsnnressnresensene 11 2 4 1 Operation in the Boot Mode esnrnnnnvonenvnnenvrnenvrnsvnrnrenvenenvenenvansnnrnsnrnnenvenensene 11 2 4 2 Operation in the User Program Mode srnnenvnnnnvrnnnnrnnnvenenvenenvnnernrnsenrnrenrenensene 13 2 5 Menu for On Board Writing Tool enronenvrnnn
3. Dialog Box erenvrnenvrnennrnrrnvernrernenvnnenvnnenrnssnrenenvenenesvenesneee 13 Main Window Huaral 14 On Board Writing Tool Menu rerenvonenvnnrnnrnnrnrenenvanenvnnenvnnenvrnssnrenenvanenvenenesseee 14 Write Command Setting Dialog BOX ernroronvrnenvrnrnrnrrnrerenvenenvenennrnsrnrnsenrenensene 15 Example of the Write Command Setting Dialog BOX renvrnrrvrnrrnronenvenenvanenvrner 16 Erase Flash Memory Block Specification Dialog Box oonooccnocccconccconcconnnnonannnn 17 Erasing Flash Memory Block Dialog Box rrernvrnrenvonenvnnenvnnernrnrenrerenvenenvenenveneee 18 Transferring Flash Memory Block Dialog Box oooooconocccnonccconccnoncconnnconanccnnncnn 18 RAM Emulation Command Dialog Box eerrvrnrnrorenvonenvnnennrnernrnrenrerenrenenvenenenneee 21 Communication Parameters onvoronvnnenvnnrnnrnnvnrenenvanenvanenvnnenvrnsnrenenvenenvanenesseee 3 Supplicd Els decided 4 HITACHI Section 1 Overview 1 1 Functions The F ZTAT microcomputer on board purge write tool hereafter referred to as the on board writing tool is a program that allows the user to control data write to flash memory of the F ZTAT microcomputer This tool operates under an operating system running on an IBM PC as described in Preface This tool facilitates writing user data in the host computer IBM PC to the flash memory of an F ZTAT microcomputer installed in the user system 1 2 Connection Figure 1 1 shows how to connect the user syst
4. figure 2 2 is then displayed Set Destination Path and Communication Port Number Select Destination Path and Communication Port Number Path K Fort Number Figure 2 2 Dialog Box for Installation HITACHI 5 a Enter a directory name in which the on board writing tool is to be copied in Path If the specified directory does not exist the installation program creates the directory to which the on board tool is copied b Enter the RS 232C port number that is used for communication with the user system as a numerical value in Port Number The default value is I COM1 c Selecting OK copies the on board writing tool files to the specified directory 5 When copying is completed the message shown in figure 2 3 is displayed When OK is selected the FLASH groups and the on board writing tool icon are registered to the program manager and installation is terminated When Cancel is selected the installation is canceled without registering the group and the icon tration Icon Registration Group and Icon Y Cancel Figure 2 3 Group and Icon Registration Confirmation Message Note The installer provided with this version will unconditionally overwrite all files listed in table 1 2 Supplied Files except for SETUP EXE and SETUP INF to the specified directory Before installation confirm the directory contents and make sure to specify the correct directory name 6 HITACHI
5. flash memory block in the Erase flash memory block list by clicking with the mouse and select Delete not to erase the memory block 16 HITACHI 3 Selecting OK in the erase flash memory block specification dialog box shown in figure 2 13 displays the erasing flash memory dialog box shown in figure 2 14 and starts to erase the flash memory block When Cancel is selected the flash memory block is not erased the dialog box is closed and the system returns to the main window Figure 2 14 Erasing Flash Memory Block Dialog Box 4 When erasing the flash memory block is completed the transferring user data dialog box shown in figure 2 15 is displayed and user data transfer is started Figure 2 15 Transferring Flash Memory Block Dialog Box HITACHI 17 5 When the user data transfer is completed and the write to the flash memory is completed without an error the transferring flash memory dialog box is closed When Stop is selected user data transfer is aborted and the dialog box is closed and the system returns to the main window 18 HITACHI 2 5 2 Mode Switchover Function Switches the program mode Operation Selecting File Mode from the menu displays the initiation dialog box shown in figure 2 5 The program mode can be selected in Mode Selection HITACHI 19 2 5 3 RAM Emulation Function Initiates the RAM emulation function for the F ZTAT microcomputer For details on RAM emulation re
6. hereby under any patents copyrights or other intellectual property rights of Renesas Electronics or others You should not alter modify copy or otherwise misappropriate any Renesas Electronics product whether in whole or in part Descriptions of circuits software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples You are fully responsible for the incorporation of these circuits software and information in the design of your equipment Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the use of these circuits software or information When exporting the products or technology described in this document you should comply with the applicable export control laws and regulations and follow the procedures required by such laws and regulations You should not use Renesas Electronics products or the technology described in this document for any purpose relating to military applications or use by the military including but not limited to the development of weapons of mass destruction Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture use or sale is prohibited under any applicable domestic or foreign laws or regulations Renesas Electronics has used reasonable care in preparing the information included in this document but Re
7. that when the menu is selected after the RAM emulation menu has been executed the default is the flash memory block end address selected when RAM is emulated In the list box the end address of each flash memory block is displayed d In Offset specify the offset of the write address This specification is used to modify the write address without changing the user data load address The default is 0 e Figure 2 12 shows an example of the write command setting dialog box to extract the addresses 0x10 to Ox5F from the user data and transfer them to the F ZTAT microcomputer Figure 2 12 Example of the Write Command Setting Dialog Box HITACHI 15 2 When OK is selected in the write command setting dialog box in the user program mode the erase flash memory block specification dialog box shown in figure 2 11 is displayed In the boot mode or when RAM emulation is selected the flash memory block is not erased and user data is transferred When Cancel is selected the dialog box is closed and the system returns to the main window without performing erase or transfer Figure 2 13 Erase Flash Memory Block Specification Dialog Box a The flash memory block in which the user data is to be installed is displayed in Erase flash memory block list The displayed flash memory block is to be erased b If a flash memory block that does not need to be erased is displayed select the corresponding block from the displayed
8. To our customers Old Company Name in Catalogs and Other Documents On April 1 2010 NEC Electronics Corporation merged with Renesas Technology Corporation and Renesas Electronics Corporation took over all the business of both companies Therefore although the old company name remains in this document it is a valid Renesas Electronics document We appreciate your understanding Renesas Electronics website http www renesas com April 1 2010 Renesas Electronics Corporation Issued by Renesas Electronics Corporation http www renesas com Send any inquiries to http www renesas com inquiry ENESAS 8 10 11 12 Notice All information included in this document is current as of the date this document is issued Such information however is subject to change without any prior notice Before purchasing or using any Renesas Electronics products listed herein please confirm the latest product information with a Renesas Electronics sales office Also please pay regular and careful attention to additional and different information to be disclosed by Renesas Electronics such as that disclosed through our website Renesas Electronics does not assume any liability for infringement of patents copyrights or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or technical information described in this document No license express implied or otherwise is granted
9. check the contents of the flash memory block information file RAM EMULATION REGISTER ERROR The RAM could not be emulated due to an invalid register value sent from the terminal Refer to the hardware manual of the device and check the contents of the flash memory block information file NO MEMORY A write could not be performed due to insufficient memory on the host computer Quit other applications and retry HITACHI 23 Index Boot mode 11 12 Connection 1 Data bit 3 Erase flash memory block specification dialog box 17 Flash memory block information 7 Flash memory block information file 7 Initiation dialog box 10 Installation 5 Mode switchover 20 Offset 16 Communication parameters 3 Parity 3 Program mode 11 20 RAM emulation 21 RAM emulation block information 7 Supplied files 4 Synchronization method 3 Termination menu 22 Transfer rate 3 User program mode 11 13 User write control program 8 Write command setting dialog box 15 16 24 HITACHI
10. em to the host computer via the RS 232C cable User system na CKIIIIITIIIITITO a Qor O HIO Host computer IBM PC Figure 1 1 Connection between User System and Host Computer HITACHI 1 Connecting to the IBM PC The RS 232C cable connects the IBM PC to the user system on which the F ZTAT microcomputer is installed Connect the RS 232C cable to the RS 232C port on the IBM PC Some IBM PCs support more than one RS 232C port Specify the port number at initiation For more details refer to section 2 1 Installation Figure 1 2 shows the physical connections between the IBM PC and the user system User system Host computer IBM PC Connector pin number Note It is assumed that the above signals are connected to the serial port of the F ZTAT microcomputer Figure 1 2 Connection between IBM PC and User System For details on connecting to the F ZTAT microcomputer refer to the F ZTAT microcomputer hardware manual 2 HITACHI 1 3 Communication Parameters The operating conditions of the host computer are listed in table 1 1 This on board writing tool operates correctly only under these conditions Set up the serial ports on the host computer according to the operating conditions The transfer rate depends on the operating frequency of the F ZTAT microcomputer used For more details refer to the F ZTAT microcomputer hardware manuals Table 1 1 Communication Parameters Item Specificati
11. fer to the F ZTAT microcomputer hardware manuals Operation 1 Selecting RAM Emulation from the menu displays the RAM emulation command dialog box shown in figure 2 16 In the Flash memory block list box the start and end addresses of each flash memory block are displayed Select the memory block for RAM emulation To cancel RAM emulation select Cancel from the list box Figure 2 16 RAM Emulation Command Dialog Box 2 Selecting OK closes the dialog box and sends the RAM emulation command to the F ZTAT microcomputer Selecting Cancel closes the dialog box 20 HITACHI 2 5 4 Termination Function Terminates the on board writing tool Operation Selecting File Quit from the menu terminates the on board writing tool HITACHI 21 2 6 Error Messages Error messages of the on board writing tool are the following e FILE INSTALL ERROR The flash memory block information file file name lt device name gt INF or user write control program lt device name gt SUB is not installed Reinstall the program e PORT OPEN ERROR The port specified at installation could not be opened Check whether the port is used by another application e FLASH WRITE ERROR Write could not be made to flash memory Erase data in the flash memory and try write again e FILE FORMAT ERROR The user write control program lt device name gt SUB or specified user program is not st
12. flash memory block information file to be used 2 Set the timeout period to detect no response when communicating with the user system in Timeout The default is five seconds The modification must be made in units of seconds 3 Select the program mode in Select Program Mode The default is the boot mode For details refer to section 2 4 Selecting the Program Mode HITACHI 9 2 4 Selecting the Program Mode Two program modes are available for writing data For details on these program modes refer to the F ZTAT microcomputer hardware manual Boot Program Mode In the boot program mode the user data is transferred to the flash memory after the user write control program is transferred to the RAM on the F ZTAT microcomputer In this case the transferred user write control program receives the user data and writes data to the flash memory on the F ZTAT microcomputer User Program Mode A program on the ROM RAM on the F ZTAT microcomputer receives the user data and writes it to the flash memory on the F ZTAT microcomputer For details on how the program in the ROM RAM works in the user program mode refer to the F ZTAT microcomputer hardware user s manuals 241 Operation in the Boot Mode 1 When the boot mode is selected in the initiation dialog box shown in figure 2 5 the boot mode dialog box shown in figure 2 6 is displayed Figure 2 6 Boot Mode Dialog Box 10 HITACHI 2 By setting the F ZTAT microcomputer to the b
13. is written to the flash memory on the F ZTAT microcomputer The user write control program must be transferred to the F ZTAT microcomputer in the boot program mode before transferring the user data 2 2 3 User Write Control Program Source File device name gt SRC The user write control program provided with this tool is a sample program assuming that the user system operating frequency is the operating frequency shown in table 1 2 Supplied Files Therefore when using an F ZTAT microcomputer with a different operating frequency the user write control program source file also provided with this tool must be modified to create a new user write control program Note that when the operating frequencies of the user write control program and F ZTAT microcomputer differ a timeout error or erase error will occur An example of modifying the operating frequency is shown below Ex Modification of symbol MHZ In the user write control program source file lt device name gt SRC symbol MHZ is defined as follows MHZ EQU H 10 16MHz a MHZ EQU H 0A IOMHz b When the operating frequency of the F ZTAT microcomputer is 16 MHz as in the above example modification is not needed However for other operating frequencies modify the value of symbol MHZ to match the operating frequency For example when the F ZTAT microcomputer operates at 10 MHz add a semicolon to the beginning of statement a and delete the semicolon at the beginning of state
14. ment b as shown below MHZ EQU H 10 16MHz a MHZ EQU H OA 10MHz b When using the source file with modification other than operating frequency or when creating an original user write control program execute the following modification of user write control program source file for the H8 538F to create the user write control program Note that the correct operation of this tool is not guaranteed if any modifications are made The following operations must be performed under MS DOS e Assemble the user write control program source file C gt ASM8A538 SRC RET e Create an absolute load module C gt LNKA538 0BJ RET e Create an S type load module C gt CNVSA538 ABS RET e Change file name to make sure that the on board writing tool is recognized as the user write control program C gt RENAMEA538 MOTA538 SUB RET 8 HITACHI 2 3 Installing the On Board Writing Tool The on board writing tool is installed by double clicking the FLASH icon within the FLASH group in the program manager When the on board writing tool is initiated the main window is first displayed and then the initiation dialog box shown in figure 2 5 is displayed Figure 2 5 Initiation Dialog Box 1 The flash memory block information file INF on the directory in which this on board writing tool is installed is displayed in the Flash memory block information file Select the
15. n use conditions Further Renesas Electronics products are not subject to radiation resistance design Please be sure to implement safety measures to guard them against the possibility of physical injury and injury or damage caused by fire in the event of the failure of a Renesas Electronics product such as safety design for hardware and software including but not limited to redundancy fire control and malfunction prevention appropriate treatment for aging degradation or any other appropriate measures Because the evaluation of microcomputer software alone is very difficult please evaluate the safety of the final products or system manufactured by you Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product Please use Renesas Electronics products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances including without limitation the EU RoHS Directive Renesas Electronics assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations This document may not be reproduced or duplicated in any form in whole or in part without prior written consent of Renesas Electronics Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics
16. nesas Electronics does not warrant that such information is error free Renesas Electronics assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein Renesas Electronics products are classified according to the following three quality grades Standard High Quality and Specific The recommended applications for each Renesas Electronics product depends on the product s quality grade as indicated below You must check the quality grade of each Renesas Electronics product before using it in a particular application You may not use any Renesas Electronics product for any application categorized as Specific without the prior written consent of Renesas Electronics Further you may not use any Renesas Electronics product for any application for which it is not intended without the prior written consent of Renesas Electronics Renesas Electronics shall not be in any way liable for any damages or losses incurred by you or third parties arising from the use of any Renesas Electronics product for an application categorized as Specific or for which the product is not intended where you have failed to obtain the prior written consent of Renesas Electronics The quality grade of each Renesas Electronics product is Standard unless otherwise expressly specified in a Renesas Electronics data sheets or data books etc Standard Computers office equi
17. ng Tool Menu HITACHI 13 2 5 1 User Data Write Function e Transfers user data to the F ZTAT microcomputer If an address range is specified the specified range is extracted from the user data and transferred to flash memory e Before transferring the user data to the F ZTAT microcomputer whether or not to erase the corresponding flash memory block must be confirmed only in the user program mode When the memory block is to be erased the user data is transferred after erasing the memory block Operation 1 When WRITE is selected from the menu the write command setting dialog box shown in figure 2 11 is displayed Figure 2 11 Write Command Setting Dialog Box 14 HITACHI a In File name specify the file name in which the user data to be written is stored If the directory in which the file exists is not found select Reference to display the file reference dialog box to select the file in which the user data is stored b In Start address specify the start address of the write The default is the start address of the flash memory Note however that when the menu is selected after the RAM emulation menu has been executed the default is the flash memory block start address selected when RAM is emulated In the list box the start address of each flash memory block is displayed c In End address specify the end address of the write The default is the end address of the flash memory Note however
18. nrnnnnrnnenvenenvnnennrnsvnrnnenvnnenvenennrnsvnrnsenreseneene 14 25 1 Us r Data Write iia id 15 2 9 2 Mode SWItehov er nassarnsssas e rn o ke e 20 253 RAM Emul tion sss sse Severo ei esb enio sv 21 eo LINK Ko naii KILO y OREA TTT A TTTTTTTTTESTI I 22 2 6 Error Messages so entenejigo funebo nn bebon krenker 23 Dex a de 25 ii HITACHI Figures Figure 1 1 Figure 1 2 Figure 2 1 Figure 2 2 Figure 2 3 Figure 2 4 Figure 2 5 Figure 2 6 Figure 2 7 Figure 2 8 Figure 2 9 Figure 2 10 Figure 2 11 Figure 2 12 Figure 2 13 Figure 2 14 Figure 2 15 Figure 2 16 Tables Table 1 1 Table 1 2 Connection between User System and Host Computer coooccconccconcnonocncnonncinnnan n 1 Connection between IBM PC and User SysteM ooooccccocccconccnoncconnnnonconccnanananccnnne 2 Installation Start Message ernrrnvrnrrnrnnnnrnnenvnnenvnrnrenrnrvrnrsnrenenrenenvanenenressnresenesenee 5 Dialog Box for Installation ooooorvrnrrnroronvonenvnrnrvnrnnenvennrnnenvenenvanenvnsesenresenvenene 2 Group and Icon Registration Confirmation Message seeeisieesesicci 6 Flash Memory Block Information File for the H8 538F 7 Initiation Dialog BOX nense a r A E aT a a a 10 Boot Mode Dialog BOX rrnrrrrnnnnrrrnrnnrrnrnnrrrrrnnnnnrrrnnnnrrernnnessrnnserernnnnssrsnrnnssennnr 11 Sending User Write Control Program Dialog BOX ocoocononccnonccconancnnonnanccnonac nno 12 User Program Mode
19. nsibility for failure or damage when used beyond the guaranteed ranges Even within the guaranteed ranges consider normally foreseeable failure rates or failure modes in semiconductor devices and employ systemic measures such as fail safes so that the equipment incorporating Hitachi product does not cause bodily injury fire or other consequential damage due to operation of the Hitachi product This product is not designed to be radiation resistant No one is permitted to reproduce or duplicate in any form the whole or part of this document without written approval from Hitachi Contact Hitachi s sales office for any questions regarding this document or Hitachi semiconductor products Preface e READ this user s manual before using the F ZTAT microcomputer on board purge write tool e KEEP the user s manual handy for future reference Do not attempt to use the F ZTAT microcomputer on board purge write tool until you fully understand its mechanism This manual describes how to use Hitachi s tool for controlling data write to flash memory of the F ZTAT microcomputer This tool operates under the Microsoft Windows 95 operating system or Microsoft WindowsNT operating system which runs on an IBM personal computer IBM PC or a compatible machine hereafter collectively referred to as IBM PC Notes 1 F ZTAT Flexible Zero Turn Around Time is a trademark of Hitachi Ltd 2 Microsoft Windows Microsoft
20. on Transfer rate 38400 19200 9600 4800 2400 bps Synchronization method Asynchronous method Data bits 8 Stop bit 1 Parity None bps Bits per second HITACHI 3 14 Supplied Software The product number of the on board writing tool is HS6400FWIW3SF Programs will be supplied on 3 5 inch 2HD floppy disks 1 44 Mbyte formatted double sided high density and double track Table 1 2 lists the files that constitute this tool Table 1 2 Supplied Files File Type File Name in 3 5 inch FD Installer SETUP EXE Installation information file SETUP INF F ZTAT MCU on board writing tool FLASH EXE Flash memory block information file device name gt INF User write control program lt device name gt SRC User write control program source file lt device name gt SUB For details refer to the Supplement of F ZTAT Microcomputer On Board Purge Write Tool User s Manual 4 HITACHI Section 2 Operation Procedures 2 1 Installation 1 Insert the floppy disk for the on board writing tool into the floppy disk drive of the IBM PC to be used 2 Initiate the SETUP EXE file on the floppy disk 3 The message shown in figure 2 1 is displayed Select OK to continue installation or select Cancel to abort installation F ZTAT Micro Computer ON Board Purge write Tool Setup This program will install F ZTAT Micro Computer ON Board Purgefwrite Tool Cancel Figure 2 1 Installation Start Message 4 The dialog box shown in
21. oot mode and selecting OK the sending the user write control program dialog box shown in figure 2 7 is displayed and the user write control program is sent The sending status is indicated by the percentage number When Cancel is selected in the boot mode dialog box the on board writing tool is terminated and the system returns to the main window Figure 2 7 Sending User Write Control Program Dialog Box 3 After the user write control program has been sent the user data can be sent to the F ZTAT microcomputer When Stop is selected user write control program sending is aborted and the initiation dialog box shown in figure 2 5 is displayed HITACHI 11 2 4 2 Operation in the User Program Mode 1 When user program mode is selected in the initiation dialog box shown in figure 2 5 the user program mode dialog box shown in figure 2 8 is displayed Set Baud rate lists the baud rates Select the appropriate baud rate Figure 2 8 User Program Mode Dialog Box 2 When OK is selected in the user program mode dialog box shown in figure 2 8 user data is sent to the F ZTAT microcomputer When Cancel is selected the system returns to the main window 12 HITACHI 2 5 Menu for On Board Writing Tool The main window is shown in figure 2 9 Figure 2 9 Main Window The menu is listed in figure 2 10 Note Items enclosed in parentheses show the shortcut menu Figure 2 10 On Board Writi
22. ored as S type records Recreate the S type load module e FLASH INFORMATION FILE ERROR The flash memory block information file lt device name gt INF contains an error or the user write control program is out of the range of the user program area information specified by the flash memory block information file Refer to the hardware manual of the device and check the contents of the flash memory information file e TIMEOUT ERROR No response was received from the F ZTAT microcomputer in a specified time Restart after checking if the F ZTAT microcomputer is operating correctly if the cable connection is correct if the same port number specified at installation is used if the correct device name has been selected in the initiation dialog box or if the Stop button has been clicked during user data transfer e FLASH ERASE ERROR Data in the flash memory cannot be erased Check the device e DEVICE ERROR User write control program cannot be sent to RAM Check the device 22 HITACHI FLASH NO WRITE DATA The user program to be written to the flash memory is outside the address range of the file specified at data write Check if the S type records of the specified file correctly match the range specification RAM EMULATION ERROR An attempt was made to emulate the RAM with a device that does not support RAM emulation Refer to the hardware manual of the device and
23. pment communications equipment test and measurement equipment audio and visual equipment home electronic appliances machine tools personal electronic equipment and industrial robots High Quality Transportation equipment automobiles trains ships etc traffic control systems anti disaster systems anti crime systems safety equipment and medical equipment not specifically designed for life support Specific Aircraft aerospace equipment submersible repeaters nuclear reactor control systems medical equipment or systems for life support e g artificial life support devices or systems surgical implantations or healthcare intervention e g excision etc and any other applications or purposes that pose a direct threat to human life You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics especially with respect to the maximum rating operating supply voltage range movement power voltage range heat radiation characteristics installation and other product characteristics Renesas Electronics shall have no liability for malfunctions or damages arising out of the use of Renesas Electronics products beyond such specified ranges Although Renesas Electronics endeavors to improve the quality and reliability of its products semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certai
24. products or if you have any other inquiries Note 1 Renesas Electronics as used in this document means Renesas Electronics Corporation and also includes its majority owned subsidiaries Note 2 Renesas Electronics product s means any product developed or manufactured by or for Renesas Electronics To all our customers Regarding the change of names mentioned in the document such as Hitachi Electric and Hitachi XX to Renesas Technology Corp The semiconductor operations of Mitsubishi Electric and Hitachi were transferred to Renesas Technology Corporation on April 1st 2003 These operations include microcomputer logic analog and discrete devices and memory chips other than DRAMs flash memory SRAMs etc Accordingly although Hitachi Hitachi Ltd Hitachi Semiconductors and other Hitachi brand names are mentioned in the document these names have in fact all been changed to Renesas Technology Corp Thank you for your understanding Except for our corporate trademark logo and corporate statement no changes whatsoever have been made to the contents of the document and these changes do not constitute any alteration to the contents of the document itself Renesas Technology Home Page http www renesas com Renesas Technology Corp Customer Support Dept April 1 2003 LENESAS Renesas Technology Corp C 7 D me T lt D D LENESAS F ZTAT Microcomputer On Board Purge Write Tool User
25. s Manual HS6400FWIW3SE Renesas Microcomputer Support Software Renesas Electronics www renesas com Cautions Hitachi neither warrants nor grants licenses of any rights of Hitachi s or any third party s patent copyright trademark or other intellectual property rights for information contained in this document Hitachi bears no responsibility for problems that may arise with third party s rights including intellectual property rights in connection with use of the information contained in this document Products and product specifications may be subject to change without notice Confirm that you have received the latest product standards or specifications before final design purchase or use Hitachi makes every attempt to ensure that its products are of high quality and reliability However contact Hitachi s sales office before using the product in an application that demands especially high quality and reliability or where its failure or malfunction may directly threaten human life or cause risk of bodily injury such as aerospace aeronautics nuclear power combustion control transportation traffic safety equipment or medical equipment for life support Design your application so that the product is used within the ranges guaranteed by Hitachi particularly for maximum rating operating supply voltage range heat radiation characteristics installation conditions and other characteristics Hitachi bears no respo
Download Pdf Manuals
Related Search