THE FLY RBP WIDE SCAN 3D LASER
Contents
1. ESE ESE produces purple cross for checking image Stand alone modes THE FLY laser can operate in stand alone mode one of 2 ways Auto or Sound activated Auto mode e Press the FUNC button and navigate until Aut is displayed e Press ENTER and 4 options are available using the UP and DOWN buttons o Hut Steps through all patterns with red blue and purple colour o Hu I Steps through all patterns with blue colour only o Aue Steps through all patterns with red colour only o Aud Steps through all patterns with purple colour only e Press ENTER to confirm the required mode Sound activated mode e Press the FUNC button and navigate until Sou is displayed e Press ENTER and 4 options are available using the UP and DOWN buttons o Sou Sound activated patterns with red blue and purple colour o So Sound activated patterns with blue colour only o Sog Sound activated patterns with red colour only o So Sound activated patterns with purple colour only e Press ENTER to confirm the required mode 152 763UK User Manual E qtx Microphone sensitivity In sound activated mode the sensitivity of the internal microphone can be adjusted via the control panel To set the sensitivity level do the following e Press the FUNC button and navigate until 5 6 is displayed e Press ENTER and 10 levels are available using the UP and DOWN buttons o 5 O lowest sensitivity 5 9 highest sensitivity e Press ENTER to confirm the required2. A 016 023 080 087 144 151 128 135 L L LJ 200 207 208 215 216 223 224 131 232 239 i O 240 247 a o Q 152 763UK User Manual 024 031 0 088 095 152 159 032 039 096 103 160 167 O 040 047 o 104 111 ke 168 175 048 055 lt S 112 119 A 176 183 E 056 063 120 127 O 184 191 MN 27 E qtx Specifications 3 BSEN60825 1 2007 Troubleshooting Check that mains power is connected correctly No power or output Check that power indicator is on and mains fuse is OK If fuse continually blows refer to qualified service personnel Check that laser aperture is not covered Ensure safety key switch is set to on Check remote power connector if in use E burner Check if in DMX mode without DMX signal Check if set to sound activated without any sound to trigger Check DMX settings reduce strobe effects if necessary If ambient temperature is low wait up to 30 mins for warm up Laser output very dim If necessary carefully clean the aperture glass with alcohol Reduce distance to projected surface Check if set to sound activated without any sound to trigger Laser on but no movement Check if in DMX mode without motion command from DMX If ambient temperature is low wait up to 30 mins for warm up Adjust DMX controls manually to check motion commands If necessary carefully clean the scanner mirror with alcohol Check DMX start address is set correctly Check DMX leads con
3. and or mirrors must be carried out periodically to optimise light output Cleaning frequently depends on the environment in which the fixture operates damp smoky or particularly dirty surroundings can require cleaning fluid Always dry the parts carefully Clean the external optics at least every 20 days 152 762UK User Manual E qtx Front panel lt _ O 4 N Laser aperture Power LED I R remote receiver Music LED ad i 5 DMX input 6 DMX output 7 Safety lock 8 9 Safety eyebolt Remote power connector 10 Control panel 11 Internal microphone 12 Cooling fan do not cover 13 Power switch 14 Mains fuse holder 13 1415 15 IEC mains inlet Control panel BBB o o ooo DOWN ENTER FUNC UP The control panel and display allow the user to adjust settings as follows e Press FUNC to navigate through the options e Press ENTER to select an option and adjust value using UP and DOWN buttons e Press ENTER again to confirm setting 152 762UK User Manual E qtx Control panel options Display Mode Press ENTER for setting press FUNC to exit Aut Aut RBP Au I blue Aue red Au purple Sou Sou RBP 5o blue Soc red 503 purple S O minimum to 5 9 maximum Oot DMX start address DO to5 10 SLA direct slave mode mimics master unit SLA Slave mode SL 0 2s delay 5L5 1 0s delay En handheld IR remote controlled
4. E qtx THE FLY RBP WIDE SCAN 3D LASER Order ref 152 763UK User Manual www avsl qtx com an ens group brand E qtx A Caution Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty Introduction Thank you for choosing THE FLY laser as part of your effects lighting equipment This product has been designed to project unique 3D geometric patterns in 3 colours across a wide area Please read and retain this manual in order to achieve the best results from your purchase and avoid damage through misuse True 3D moving effects Large area scanning through wide angle aperture 0 22W total laser power Red 100mW Blue 120mW Auto sound activated modes 10 channel DMX operation Master slave mode Supplied with I R remote control Easy digital display to set the mode of operation Key controlled for laser safety We recommend that this product is used within the guidelines HSG95 152 762UK User Manual E qtx CAUTION e Please read this manual fully before installing or operating this product as it contains important safety information relating to its installation and operation e This Class 3B laser product emits hazardous levels of optical radiation and will cause injury to the eyes if viewed directly e This product is not suitable for projection directly at audiences or other personnel e This product must not be used for any form of au
5. dience scanning application and is for professional use only Important information This product is a Class 3B laser and should only be installed and used by personal who are trained in the management of laser radiation and are able to operate in accordance within the guidance given by the Health and Safety Executive HSE in HS G 95 The Radiation Safety of Lasers used for Display purposes Copies of this guide can be downloaded from the HSE website WWw hse gov uk pubns priced hsg95 pdf This product contains no user serviceable parts Under no circumstances should any attempt be made by the user to dismantle or modify it in any way 152 762UK User Manual E qtx Installation instructions This product must be securely mounted with adequate fixings to hold the weight If mounted at height use a safety wire attached to the eyebolt and a secondary fixing point Position the aperture so that its emission is always directed away from people and objects that are able to reflect the emission towards people In this regard the separation distances of 3 metres vertically and 2 5 metres horizontally cited in HS G 95 and shown below must be observed Vertical bird s eye view Laser projection should be Balcony at least 3m above audience and should be below balcony level Laser projector Audience exclusion zone r 152 763UK User Manual E qtx Vertical cross sectional view ene json a AN as ave E K gt
6. ith an independent fixing Use the integral mounting bracket with a suitable clamp for stand or truss being fixed to When mounting directly to ceiling surfaces be sure to use adequate fixings for the supporting material 152 763UK User Manual E qtx Connecting to mains earth wire ground must be connected Use the supplied IEC lead to connect to the main power supply as follows L Brown Live DO me eai For your safety please kindly pay attention to all of the warnings below Always plug in the power plug last and disconnect from the mains when the device is not in use or before cleaning Do not install and operate the device in rain or extreme heat moisture or dusty environments This device is for indoor use only and in a dry environment Do not switch on immediately Wait until the unit reaches room temperature Do not shake the device and avoid brute force when installing or operating Do not use the device during thunderstorms and please disconnect the power Do not use solvents or aggressive detergent to clean the device Use a soft and clean cloth Do not modify the device or the connected power cord without authorisation Do not stare into the aperture This product emits hazardous levels of optical radiation and will cause serious injury to the eyes if viewed at close range This product should be securely mounted so that its output emission is always directed away from people a
7. nator Solder a 120 Ohm resistor between PIN 2 and PIN 3 into a 3 pin XLR plug and plug it in the DMX output of the last fixture 152 763UK User Manual E qtx DMX parameters Channel Parameter Value Function Z Z o o Auto mode blue S 056 083 Auto mode blue 084 111 Auto mode red Auto modered SS DMXmode S O 252 255 DMX mode CH2 Pattern 000 255 32 Patterns as shown in PATTERN LIST _ 000 049 RBP 075099 rae o ooo Colour Alternate red purple Alternate blue purple Color roling ooo 225 255 Color rolling CH4 Colour speed a 255 Stop then slow to fast 000 127 127 100 5 Size 128 169 Zooming in Zoom 170 209 Zooming out oa 255 Zooming in amp out 000 127 127 X axis ETE 191 Clockwise rotation e255 255 Anticlockwise rotation 000 127 127 ET 191 128283 255 CH7 Y axis 000 127 127 Y axis roll oa 191 102255 255 128 different fixed position on X 128 different fixed position on Y Clockwise rotation Anticlockwise rotation 0 359 degree fixed Y axis rolled Clockwise rolling Anticlockwise rolling 000 127 127 0 359 degree fixed X axis rolled X axis roll 128 191 Clockwise rolling E 255 Anticlockwise rolling 000 127 127 0 359 degree fixed Z axis rotation 128 191 Clockwise rotation 128 255 Anticlockwise rotation CH10 Z axis 152 763UK User Manual E qtx Patterns Value pattem 000 007 064 071 i 008 015 072 079 aa ZX 136 143
8. nd at objects that are able to reflect emission towards people In this regard the separation distances cited in HS G 95 should be observed The symbol ile mf determines the minimum distance from lighted objects The minimum distance between light output and the illuminated surface must be more than 0 5m 152 762UK User Manual E qtx Replacing the fuse First disconnect from the mains power supply then remove the fuse holder above the IEC Socket to reveal the fuse Replace with the correct fuse rating as stated on the product or in the user manual Then lock the fuse holder cover back into place General maintenance Be sure to power off the fixture before conducting maintenance To maintain optimum performance and minimise wear fixtures should be cleaned frequently Usage and environment are contributing factors in determining frequency As a general rule fixtures should be cleaned at least twice a month Dust build up reduces light output amp performance as well as overheating This can lead to reduced life and increased mechanical wear Unplug fixture from power Use a vacuum or air compressor and a soft brush to remove dust collected on external vents and internal components Clean all glass when fixture is cold with a mild solution to the cloth or tissue and drag dirt and grime to the outside of the lens Gently polish optical surfaces until they are free of haze and lint The cleaning of internal and external optical lenses
9. nections and polarity are OK MPERA eee Check DMX leads are not running close to high voltage cables Test DMX with alternative controller Important This product conformed to Laser amp LED Safety standard BSEN60825 1 2007 incorporating corrigendum 2008 Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life X Disposal The Crossed Wheelie Bin symbol on the product means that the product is classed as Electrical or C mm The goods must be disposed of according to your local council guidelines Errors and omissions excepted Copyright 2013 AVSL Group Ltd 152 763UK User Manual
10. s O e ni gi Audience exclusion zone ee a A e 2 E as U Oe ats 5 on should be ee seat project e Laser projector gt 3 metres Audience allowed in this zone re A eu ALAN q Fiy LAN 4 gt fy z A gt q t pi 4 Pp gt q i CIAL lem NESEY Te i q es Unpacking Please check the contents to ensure that the product has been received in good condition LR remote control x 1pc IEC Power Lead x 1pc Safety Keys x 2pcs If you find any accessory is missing or the product has arrived with any problems please contact your retailer at once This product contains no user serviceable parts so make no attempt to try to fix or modify this item yourself as this will invalidate the warranty We recommend you keep the original package and proof of purchase for any possible replacement or returned demand 152 762UK User Manual E qtx Setting up pa 1 Unpack the laser ensuring all packaging and tape is removed 2 Always test the laser before fixing in a permanent location 3 4 Insert the safety key and turn to a quarter turn clockwise At this point ensure that no Connect the IEC mains plug and switch the rear power switch on one is exposed to laser radiation Select which mode you want to operate the laser in Leave the laser to run for 10 minutes before installing in its location Installation When mounting at height attach a safety wire to the eyebolt w
11. sensitivity level Master Slave mode One or more THE FLY lasers can be operated simultaneously in slave mode from a master unit operating in auto or sound activated mode To set up a master slave chain connect a DMX lead from the DMX output of the master unit and connect to the DMX input of the slave unit Further slave units can be connected from the first slave unit via DMX in the same manner To enable slave mode on the unit s to be controlled e Press the FUNC button until SLA is displayed e 6 options are available using the UP and DOWN buttons o SLA Mimics the master unit exactly SL Mimics the master unit with a 0 2 second delay Sto Mimics the master unit with a 0 4 second delay SLJ Mimics the master unit with a 0 6 second delay SLY Mimics the master unit with a 0 8 second delay o 5L5 Mimics the master unit with a 1 0 second delay e The slave mode is only active when a master signal is received via DMX O O O 152 763UK User Manual E qtx Remote control mode THE FLY laser can be operated using the supplied handheld infra red remote control To use this remote control firstly remove the plastic tab at the bottom of the remote to activate the internal battery If necessary this can be replaced with a standard CR2025 button cell The Remote mode for the laser unit is set via the control panel as follows e Press the FUNC button until E is displayed and press ENTER e Direct the handheld remote con
12. trol toward the I R receiver on the front panel e See the remote control options below for operation Remote handset Auto mode Sound activated Laser On Off Colour Pause effect Pattern select Sound Sensitivity Fixed patterns wh o 2 Pattern repeat Laser Remote Note When sound activated mode is selected from the remote control Press Sound activated then B then a number from 1 to 9 to set microphone sensitivity Test mode THE FLY laser can produce a fixed cross pattern for testing size and projection against a surface for adjustment and positioning To enter the test mode press the FUNC button until the display shows ESE and press ENTER 152 763UK User Manual E qtx DMX mode The fixture is equipped with 3 pin XLR connectors for DMX input and output These connectors are wired in parallel Only use a shielded twisted pair cable designed for 3 pin XLR plugs and connectors in order to connect the controller with the fixture or one fixture with another DMX output DMX input XLR mounting sockets rear view XLR mounting plugs rear view 1 Shield 2 Signal 3 Signal Building a serial DMX chain lt DMX 512 Controller operation a Master slave operation Caution At the last fixture the DMX cable has to end with a termi
Download Pdf Manuals
Related Search