Ambiance Portable Propane Patio Heater Manual
Contents
1. discoloration are not covered This ONE YEAR Consumer warranty is only applicable for consumer or residential applications We offer a 120 day warranty protection for fire features that are used in a commercial or rental application Commercial warranty does NOT cover emitter grids glass tubes reflectors ignition or burners or component failure caused by abuse transportation or misuse This warranty is valid from the original date of purchase and is transferable Please keep your original sales receipt or invoice Proof of purchase is required to obtain warranty replacement Patio Comfort retail dealers or distributors do NOT have the authority to modify alter or in any way change the product or the terms and conditions of this warranty We will NOT cover the following e Freight charges to our facility in Irvine California Assembly or installation costs Improper assembly or improper hook up Damage or repairs that result from spiders or other insect nesting Damage due to weather conditions or lack of proper maintenance and cleaning Normal maintenance or burner adjustments Cleaning or periodic general maintenance Shipping or freight damage Service provided by an unauthorized agency or service person Overtime weekends and holidays Service visits to correct improper assembly or installation Damages caused by abuse accident acts of nature vandalism transportation or alteration We will not repair rented fire features that have been repu2. Wheel Assembly H Bottom plate a Front Panel O Ceramic Fiber DESCRIPTION QUANTITY DESCRIPTION QUANTITY A Reflector Block Belt 1 B Mesh Gas Hose amp Regulator D TopPlate F G J Replace parts only with OEM parts Please contact Black Silicone Ring servicing dealer or AEI Corporation for exact Control Box Assembly replacement parts Lower Support Short P Protect L6 1 Bhck si La 22 piance REDEFINING THE ART OF FIRE PLEASE NOTE TO INSURE WARRANTY REGISTRATION PLEASE FILL OUT WARRANTY CARD BELOW AND RETURN MAIL AEI CORPORATION WILL NOT SELL OR USE OWNER INFORMATION FOR ANY PURPOSES If you would like you can fax this to us at 949 474 0559 or e mail it to info aeicorporation com Ambiance rire Feature WARRANTY REGISTRATION IMPORTANT Please fill out this Warranty Registration within 10 days of purchase Thank you for purchasing an Ambiance Fire Feature by AEI Corporation Name Address City ST ZIP Phone Date Purchased Where Purchased Dir Name and City Ambiance ModelZPC14SS 3 SS Stainless Steel Serial Number found inside tank enclosure PC14AB Antique Bronze Fuel LPG NAT GAS __ Reason for Choosing a the Ambiance Fire Feature Advertising Quality Price Features Rec by Friend Other please write below SUGGESTIONS
3. direct sunlight other ignition sources or where temperatures exceed 120 degrees F 49 C Propane vapours are heavier than air and can leaks using soapy water Never use a flame _ accumulate in low places If you smell gas leave Use as a heating appliance only Never alter in any the area immediately way or use with any device Never install or remove propane cylinder while fire feature is lit near flame pilot light other ignition sources or while fire feature is hot to touch A The glass tube emitter grid and reflector are red hot E and can uie don cbs too close to the CAUTION burner Keep flammables at least 36 91 cm from T BD sides amp 24 61 cm from top Keep gasoline and other CAUTION indicates an imminently hazardous flammable liquids and vapors well away from fire situation which if not avoided may result in minor or feature moderate personal injury or property damage Store the propane cylinder outdoors in a well ventilated space out of reach of children Never store the propane cylinder in an enclosed area house garage etc If fire feature is to be stored indoors disconnect the propane cylinder for outdoor storage An appliance may be installed with shelter no more inclusive than a With walls on all sides but with no overhead cover b Within a partial enclosure which includes an overhead cover and no more than two side walls These side walls may be parallel as in a breezeway or at ri
4. instructions Do not block air flow openings into the combustion chamber into or out of the fire feature Never use the fire feature in spaces which do or may contain volatile or airborne combustibles or products such as gasoline solvents paint thinner dust particles or unknown chemicals During operation this product can be a source of ignition Keep fire feature area clear and free from combustible materials gasoline paint thinner cleaning solvents and other flammable vapors and liquids Do not use fire feature in areas with high dust content Minimum fire feature clearances from combustible materials 36 91 cm from the sides amp 24 61 cm from the top e Carbon Monoxide CO poisoning produces flu like symptoms watery eyes headaches dizziness fatigue and possibly death You can t see it and you can t smell it It s an invisible killer If these symptoms are present during operation of this product get fresh air immediately For outdoor use only e Never use inside house or other unventilated or enclosed areas e This fire feature consumes air oxygen Do not use in unventilated or enclosed areas to avoid endangering your life A DANCI E EXPLOSION FIRE HAZARD SERVICE SAFETY Keep all connections and fittings clean Make sure propane cylinder valve outlet is clean During set up check all connections and fittings for Never store propane near high heat open flames pilot lights
5. than air and leaking propane will settle to the lowest level possible It can ignite by ignition sources including matches lighters sparks or open flames of any kind many feet away from the original leak Use only propane cylinders set up for vapor withdrawal e Store or use propane gas in compliance with local ordinances and codes or with ANS NFPA 58 Turn off propane when not in use A WARNING Alert children and adults to the hazards of high surface temperatures Stay away from these surfaces to avoid burning skin or igniting clothing Carefully supervise young children when in the vicinity of the fire feature Do not hang clothing or any other flammable materials from the fire feature or place on or near the fire feature Replace any guard or protective device removed for servicing the appliance prior to placing back in service Installation and repair should be done by a qualified service person The fire feature should be inspected before use and annually by a qualified service person More frequent cleaning may be required as necessary It is imperative that the control compartment burners and circulating air passageway of the appliance be kept clean Before beginning assembly of product make sure all parts are present Compare parts with package contents list and hardware contents above If any part is missing or damaged do not attempt to assemble the product Contact AEI Customer Service at 949 474 3070 Mo
6. 559 www aeicorporation com or info aeicorporation com 2641 Du Bridge Ave Irvine CA 92606 Caution Always allow fire feature to cool before moving or attempting service 20 Service amp Warranty Information To learn how to service and acquire replacement parts first contact your selling dealer or call us directly at 949 474 3070 or e mail us at info aeicorporation com for assistance Please provide us with the model number and serial number for best possible service and support Please be sure to fill out your Ambiance Warranty card so that we can have the record on file We will not use this information for any marketing activities Our company has been in the quality leisure gas appliance business since 1966 and we want to be sure that you are happy with our products and support services Be sure to use only genuine Ambiance replacement parts for your fire feature Use of unauthorized parts or modification of our parts will void the fire feature warranty and could create personal injury or property damage Always be sure that your fire feature is cool to the touch before attempting any service or maintenance procedures Warranty AEI will Cover Ambiance Fire Features are warranted against any defects in parts for a period of 1 year from the date of purchase with original purchase receipt We will warranty against structural defects all external stainless steel components such as panels for 3 Years from date of purchase Normal scratches wear
7. Owners A n ege Manual OUTDOOR REDEFINING THE ART OF FIRE Fire Feature MODEL PC14SS and PC14AB ADNEJ If you smell gas 1 Shut off gas to the appliance 2 Extinguish any open flame 3 If odor continues keep away from the appliance and immediately call your gas supplier or fire department j il M FE A WARNING WARNING indicates an imminently hazardous situation which if not avoided will result in death or serious injury BAN NAAN SCS yi DDR NI l TSSISIN D ARAN A NU fi al A WARNING Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance A WARNING For Outdoor Use Only A WARNING Improper installation adjustment alteration service or maintenance can cause property damage injury or death Read the installation operation and maintenance instructions thoroughly before installing or servicing this equipment CRN Jl CERT FRE D p ANS Z83 26 2007 CSA 2 37 2007 Gas Fired Outdoor Infrared Patio Heater ANS Z83 26a 2008 CSA 2 3 a 2008 Gas Fired Outdoor Infrared Patio Heater PACKAGE CONTENTS Reflector Emitter Grid LS Glass Tube Fixer B CLA A Top Plate Sr _ _ 3 1 Upper Support Long Protective Guard ea Glass Tube aBoide Panel B Black Silicone
8. Ring M m M a _ 222322 9 zzzz2u ontrol Box Assembly 3 a S f popopo tatt TTD M Lower Support Short it 1 NDURN Ju Gas Hose Assb js Wheel Assb tj V Bottom Plate B Front Panel e ue oa Ceramic Fiber PART DESCRIPTION DESCRIPTION QUANTITY Reflector Block Belt A B EmiterGid M Gas Hose amp Regulator N D jTopPate Fo om G Black Silicone Ring Protective Guard Q Ceramic Fiber HARDWARE CONTENTS shown actual size OO OO O pm pm Wing nut Small Flat Stud M5 x 12 mm Screw Bolt Qty 3 Washer Qty 3 Qty 35 Qty 8 Qty 6 Ol a Om e Knob M4 x 10 mm Chain Fixing Qty 1 Bracket Qty 1 Screw D Q e Long Stem Lighter Wrench Qty 1 Qty 1 Qty 1 A This manual contains important information about the assembly operation and maintenance of this patio fire feature General safety information is presented in these first few pages and Is also located throughout the manual Keep this manual for future reference and to educate new users of this product This manual should be read in conjunction with the labeling on the product Safety precautions are essential when any mechanical or propane fueled equipment is involved These precautions are necessary when using storing and servicing this patio fire feature Using this equipment with the respect and caution demanded will r
9. ZARD For outdoor use only Never use inside house or other unventilated or enclosed areas This fire feature consumes air oxygen Do not use in unventilated or enclosed areas to avoid endangering your life Caution Do not attempt to operate until you have read and understand all General Safety Information in this manual and all assembly is complete and leak checks have been performed Before Turning Gas Supply ON 1 Your fire feature was designed and approved for outdoor use only Do NOT use it inside a building garage or any other enclosed area 2 Make sure surrounding areas are free of combustible materials such as wood fabric plants gasoline and other flammable vapors or liquids 3 Make sure that there is no obstruction to air ventilation Be sure all gas connections are tight and there are no leaks 4 Be sure the cylinder housing is clear of debris Be sure any component removed during assembly or servicing is replaced and fastened prior to starting Before Lighting NOTE 1 Ambiance Fire Feature should be thoroughly inspected before each use and by a qualified service person at least annually Always wait at least 5 minutes before attempting to relight a hot Ambiance Fire Feature 2 Inspect the hose assembly for evidence of excessive abrasion cuts or wear Suspected areas should be leak tested If the hose leaks it must be replaced prior to operation Only use the replacement hose assembly specified by AEI C
10. and Propane Installation Code Your local library or fire department should have this book Storage of an appliance indoors is permissible only if the cylinder is disconnected and removed from the appliance A cylinder must be stored outdoors ina well ventilated area out of the reach of children A disconnected cylinder must have dust caps tightly installed and must not be stored in a building garage or any other enclosed area The maximum inlet gas supply pressure 250 PSI The minimum inlet gas supply pressure 5 PSI is required for purpose of input adjustment The fire feature must have a minimum output rating of 16 000 BTU hr when it is not working at full capacity The pressure regulator and hose assembly supplied with the appliance must be used The installation must conform with local codes or in the absence of local codes with national fuel gas code ANS Z223 1 NFPA54 natural gas and propane Installation Code CSA B149 1 or propane storage and handling code B149 2 NOTE we have provided three tabs at the base of the fire feature where it can be secured to a patio If installed in a windy area or where it may be bumped or tipped fasteners are not included we strongly recommend securing Ambiance to patio 12 ASSEMBLY INSTRUCTIONS Warning A dented rusted or damaged propane cylinder may be hazardous and should be checked by your propane supplier Never use a propane cylinder with a damaged valve connec
11. ator connection CRITICAL LEAK TEST LOCATION Regulator Cylinder connection 1 Make 6 8 oz of leak check solution one part liquid dish washing detergent and three parts water 2 Make sure tank valve is OFF and valve to Ambiance Fire Feature is in OFF Position 3 Apply several ounces of solution where hose attaches to regulator 4 Apply several ounces of solution where regulator connects to cylinder apply the soapy solution to all hose amp valve connections 5 Turn tank cylinder valve ON If bubbles appear at any connection there is a leak follow instructions below 1 Turn cylinder valve OFF 2 If leak is at hose regulator connection Tighten accordingly with wrenches The fittings are flare to flare and tape of sealant should not be used If bubbles continue appearing the hose should be returned to the place of purchase or contact AEI Corporation at 949 474 3070 3 If leak is at regulator cylinder valve connection disconnect reconnect and perform another leak check Apply the soapy solution to all hose amp valve connections If you continue to see bubbles after several attempts cylinder valve or regulator fitting is defective and should be returned to cylinder s place of purchase If NO bubbles appear at any connection the connections are secure NOTE Whenever gas connections are loosened or removed you must perform a complete leak test 14 OPERATION INSTRUCTIONS DANGER CARBON MONOXIDE HA
12. d intact and operable o alterations have been made All gas connections are secure and do not leak Outside temperature is adequate Please note that wind velocity is below 10 mph Unit will operate at reduced efficiency below 40 F Fire feature is outdoors outside any enclosure There is adequate fresh air ventilation CON OOR WN gt 17 OPERATION INSTRUCTIONS 9 Fire feature is away from gasoline or other flammable liquids or vapors 10 Fire feature is away from windows air intake openings sprinklers and other water sources 11 Fire feature is located at least 24 top 36 sides from combustible materials 12 Fire feature is on a hard and level surface 13 There are no signs of spider or insect nests 14 All burner passages are clear 15 All air circulation passages are clear 16 Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition 17 Young children should be carefully supervised when they are in the area of the fire feature 18 Clothing combustible materials or other protective material should not be hung from the fire feature or placed on or near the fire feature 19 Any guard or other protective device removed for servicing the fire feature must be replaced prior to operating the fire feature 20 Any repair of this fire feature should be done by a qualified service person The fire feature should be
13. educe the possibilities of personal injury or property damage The following symbols shown below are used extensively throughout this manual Always follow these precautions as they are essential when using any mechanical or fueled equipment Ames DANGER indicates an imminently hazardous situation which if not avoided will result in death or serious Failure to comply with the precautions and instructions provided with this fire feature can result in death serious bodily injury and property loss or damage from hazards of fire explosion burn asphyxiation and or carbon monoxide poisoning Only persons who can understand and follow the instructions should use or service this fire feature CARBON MONOXIDE HAZARD This appliance produces carbon monoxide which has no odor Using it in an enclosed space can kill you Never use this appliance in an enclosed space such as a camper tent or home A A DANGER A YNNE CARBON MONOXIDE HAZARD e EXPLOSION FIRE HAZARD e This fire feature is a combustion appliance All Keep solid combustibles such as building combustion appliances produce carbon monoxide materials paper or cardboard a safe distance away CO during the combustion process This product is from the fire feature as recommended by the designed to produce extremely minute non hazardous instructions amounts of CO if used and maintained in accordance e Provide adequate clearances around air with all warnings and
14. ght angles to each other c Within partial enclosure which includes an overhead cover and three side walls as long as 30 percent or more of the horizontal periphery of the enclosure is permanently open A SAFETY INFORMATION ANNE California Proposition 65 Combustion by products produced when using this product contain chemicals known to the State of California to cause cancer birth defects and other reproductive harm A WARNING BURN HAZARD Never leave fire feature unattended when hot or in use Keep out of reach of children Certain materials or items when stored under the fire feature will be subjected to radiant heat and could be seriously damaged A WARNING We cannot foresee every use which may be made of our fire features Check with your local fire safety authority if you have questions about fire feature use Other standards govern the use of fuel gases and heat producing products for specific uses Your local authorities can advise you about these In Canada installation must conform to local codes If no local codes exist follow the current National standards of CANADA CAN CGA B 149 2 PREPARATION This product is fueled by propane gas Propane gas is invisible and flammable An odorant is normally added to help detect leaks and can be described as a rotten egg smell The odorant can fade over time so leaking gas is not always detectable by smell alone Propane gas is heavier
15. inspected before use and at least annually by a qualified service person 21 More frequent cleaning may be required as necessary It is imperative that control compartment burner and circulating air passageways of the fire feature be kept clean After Operation be Certain Gas control is in OFF position Gas tank Valve is OFF Disconnect Propane gas cylinder CARE AND MAINTENANCE A MENNE FOR YOUR SAFETY Do NOT touch or move fire feature for at least 45 minutes after use Reflector is hot to touch Allow reflector to cool before touching To enjoy years of outstanding performance from your fire feature make sure you perform the following maintenance activities on a regular basis 1 Keep exterior surfaces clean Use warm soapy water for cleaning Never use flammable or corrosive cleaning agents While cleaning your unit be sure to keep the area around the burner and pilot assembly dry at all times Do not submerge the control valve assembly If the gas control is submerged in water do NOT use it It must be replaced 2 Keep the appliance area clear and free from combustible materials gasoline and other flammable vapors and liquids 3 Do not obstruct the flow of combustion and ventilation air 4 Keep the ventilation opening s of the cylinder enclosure free and clear from debris 5 Air flow must be unobstructed Keep controls burner and circulating air passageways clean 6 Regularly replace AA Batter
16. n Fri 7 a m to 4 p m PST for replacement parts or service questions Estimated Assembly Time 90 minutes Tools Required for Assembly 2 Phillips screwdriver w medium blade part LL M6 Wrench part KK Leak Detection Solution not included ASSEMBLY INSTRUCTIONS 1 Insert the hoods of bottom plate O to the lower holes of the three lower supports K Insert the hoods of control box assembly J to the upper holes of the three lower support K Note Make sure to align the side of bottom plate O with the holes to accommodate front plate P with the side of control box assembly J with the magnet Note Bottom Plate with tank retention hole has folded edges facing up 2 Insert three upper supports E to the three lower supports K Please note be sure that the upper support E slide down completely into the lower supports K before attempting to install screws ASSEMBLY INSTRUCTIONS 3 Use Phillips screwdriver LL to fasten the control box assembly J and the bottom plate O with M5 x 12 mm screws DD Hardware Used EE Mex tomm Screw f x9 Phillips m Screwdriver 4 Use Phillips screwdriver LL to secure the top plate D to the upper supports E with M5 x 12 mm screws DD Hardware Used DD M5 x 12 mm Screw oons x6 Phillips Screwdriver ASSEMBLY INSTRUCTIONS 5 Using wrench KK to assemble the wheel assembly N to the bottom plate O with M6
17. n t light Q O U B S o 2 9 lt Q gt 3 3 5 D lt D Ll E o Q D j D 5 O C a c D m c aw 9 D nan Zz D Oo c OQ O O o lt O Oo D B l i Outdoor temperature is less than 40 F and urner frame IS IOW hank is less than 1 4 full Use a full cylinder Check burner and orifices for debris Blockage clean w compressed air Clean reflector glass amp burner screen Blockage in burner Remove blockage and clean burner inside and outside Adjust the position of control box assembly Clean burner and orifices w compressed air Carbon build up Thick black smoke Gas odor with extreme yellow tipping of flame Fire feature glow is excessively uneven Bad regulator Change the regulator Spiders and insects Clean burner and orifices Clean burner and orifices replace ceramic burner if damaged Fire feature makes popping noises J o D o o cio EIE 2 5 XE em S o 2 6 o do o En p o 2 o 3 5 gt 5 2 IO O a2 o J o 5 5 F mai E oz 77 o amp o o CD gt O Oo O D T 77 o O O F S e 2 lt O O A Q D O Q 5 Q T O 3 a i D o T o c B D D 3 5 D p lt O CARE AND MAINTENANCE Keep area in and around Ambiance Fire Feature Free from insects P opiders and other small insect are attracted to the odorant found in gas e Spiders and insects can nest in burner or orifices This dangerous co
18. ndition can damage fire feature and render it unsafe for use Clean burner holes by using compressed air burner is fragile handle with care when cleaning e Carbon deposits may create a fire hazard to clean remove the emitter grid mesh assembly take down one side of protective guards Then take the glass tube UP AND THEN OUT from the Ambiance Fire Feature wash and clear After that reassemble the glass tube and the rest of parts Note In a salt air environment such as near an ocean corrosion occurs more quickly than normal Frequently check for corroded areas and repair them promptly TIP Use high quality automobile wax to help maintain the appearance of your fire feature Apply to exterior surfaces from upper support long down Do not apply wax to emitter grid glass tube or reflector Storage Transporting or during periods of extended inactivity Between uses e Turn control knob OFF e Disconnect LP cylinder eStore fire feature upright in an area sheltered from direct contact with inclement weather such as wind rain sleet hail snow dust and debris e f desired cover fire feature to protect exterior surfaces and to help prevent build up in air passages Note Wait until fire feature is completely cooled off before moving or covering Service Only a qualified service person should repair gas passages and associated components Contact AEI Corporation for OEM parts at Ph 949 474 3070 Fax 949 474 0
19. orporation for Ambiance Lighting Note This fire feature is equipped with a pilot light that allows for safer startups and shutdowns Pilot must be lit before main burner can be started 1 Turn the control knob to the OFF position 2 Fully open LP cylinder valve 3 Push control knob in and rotate to pilot position Figure 1 Note For initial start or after any cylinder change hold control knob in at PILOT position for up to 1 minute to purge air from gas lines before proceeding Igniter Variable control knob Figure 1 Figure 2 15 OPERATION INSTRUCTIONS 4 Push and release the igniter button until pilot flame is visible through the glass tube 5 Once the pilot is lit continue to depress the control knob for 30 seconds 6 If the pilot does light or does not stay lit repeat steps 4 to 6 7 If after repeating steps 4 to 6 pilot does not light then check battery first Push in control knob and turn counterclockwise to PILOT Figure 3 As you are depressing the control knob you can manually light with a long stem lighter Figure 4 Igniter Variable control knob Figure 3 Figure 4 Figure 5 8 Push in and turn the control knob to the HIGH then release control knob If you want a lower temperature push in the control knob and turn counterclockwise to the LOW position Figure 5 Note lf pilot fails to remain lit all valves should be closed and a waiting period of at least 5 minutes sho
20. rchased for residential use We will not cover normal wear and tear such as discoloration to the finish scratches chips abrasion or fading from exposure to sunlight or other atmospheric conditions Your Legal Rights e CONSEQUENTIAL DAMAGES INCIDENTAL DAMAGES OR EXPENSES INCLUDING DAMAGES TO PROPERTY SOME STATES PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU WE WILL NOT BE RESPONSIBLE FOR ANY COSTS RELATING TO LOST REVENUE BUSINESS INTERRUPTION OR ANY LEGAL THEORY UPON WHICH ANY CLAIM MAY BE BASED e PURCHASER ASSUMES ALL RISK IN THE ASSEMBLY AND OPERATION OF THIS APPLAINCE FAILURE TO FOLLOW THIS MANUAL S WARNINGS AND INSTRUCTIONS CAN RESULT IN SEVERE PERSONAL INJURY DEATH OR PROPERTY DAMAGE This warranty is for all Ambiance Fire Features purchased and used in the 50 US states The District of Columbia and Canada This warranty applies even if you should move during the warranty period Should you sell the product during the warranty period the warranty protects the new owner as well This warranty provides you with specific legal rights You may also have other rights that vary from state to state How to obtain service For most product or assembly related problems your selling dealer can provide you with help The product has been designed to be as trouble free and maintenance free as possible and requires minimal assembly Should yo
21. tion The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U S Department of Transportation DOT or the standard for cylinders soheres and tubes for transportation of dangerous goods and commission CAN CSA B339 Standard 20 Ib The cylinder must have a listed opd overfilling prevention ey device The cylinder must have a connection device compatible with the connection for the appliance The cylinder used must include a collar to protect the cylinder valve Never connect an unregulated propane cylinder to the fire feature Use only Ambiance approved replacement parts These can be ordered through your dealer or directly from AEI Corporation 949 474 3070 M F 7 a m to 4 p m PST e Do not store a spare LP gas cylinder under or near this appliance e Never fill the cylinder beyond 80 percent full e Place the dust cap on the cylinder valve outlet whenever the cylinder is not in use Only install the type of dust cap on the cylinder valve that is provided with the cylinder valve Other type of caps or plugs may result in leakage of propane 13 OPERATION INSTRUCTIONS Leak Check A WARNING Perform all leak tests outdoors Extinguish all open flames NEVER smoke while carrying out the leak test Do not use the fire feature until all connections have been leak tested and do not leak CRITICAL LEAK TEST LOCATION Hose Regul
22. u have a problem with missing parts please contact your selling dealer or contact us directly at 949 474 3070 We exercise extreme care in the assembly and manufacturing process but we know errors can be made and we want to take care of them as quickly and painlessly as possible Since product improvement is an ongoing process we reserve the right to change this products materials specifications or design without notice We know that you and your family will enjoy your Ambiance Fire Feature product for many years to come and that it will be a welcome addition and important ingredient to your outdoor entertainment and activities 21 Replacement parts available from servicing dealer or AEI CORPORTION REPLACEMENT PARTS LIST www aeicorporation com 949 474 3070 e mail info aeicorporation com PO Box 16097 Irvine CA USA 92606 or 2641 DuBridge Ave Irvine CA 92623 6097 ny Reflector D i p oa Emitter Grid Glass Tube Fixer 5 ay Top Plate f amp 559 9 Upper Support Long ii aum zh Protective Guard i WM VIN i fem Glass Tube MM Yj Wy 14 V Yi 7 p aie Vy iN a NYY CE Wy Side Panel Black Silicone Ring Control Box Assembly Lower Support Short m S h aa S f popopo tint TIL Block Belt eT B Bi P oJ Rs Gas Hose amp Ke
23. uld be allowed before attempting to light WARNING If you attempt to relight the pilot without waiting you will get a flash that could cause bodily harm and property damage If you experience any ignition problem please consult Troubleshooting on page 19 Caution Avoid inhaling fumes emitted from the fire feature s first use Smoke and odors from the burning of oils used in manufacturing will appear Both smoke and odor will dissipate after approximately 30 minutes The fire feature should NOT produce thick black smoke Note The burner may be noisy when initially turned on To eliminate excessive noise from the burner turn the control knob to the PILOT position Then turn the knob to the level of heat desired Note In normal conditions the height of flame is 2 3 height of glass tube in HIGH position The height of flame is 1 3 height of glass tube in LOW position The flame is stable and bright No noise nor black smoke the presence of these elements indicate a problem Pleaser consult Troubleshooting section on page 19 Actual Flame can be much higher if set on HIGH Normal Abnormal 16 OPERATION INSTRUCTIONS A WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this fire feature Holding in the control knob for more than 20 seconds before igniting the gas will cause a ball of flame upon ignition When fire feature is ON The flame should be blue with straight yello
24. utt x 1 Chain Philips screwdriver _ 9099 10 ee e cm cm oo eae gt eo wm ASSEMBLY INSTRUCTIONS 11 Assemble the protective guard and mesh by inserting the hooks of protective guard F E to the holes of upper supports E Put the mesh B on the top plate D Make sure the screw holes align the holes of top plate D Use Phillips screwdriver LL to secure the mesh B and protective guard F to the top plate D with M5 x 12 mm screws DD and fixing bracket FF Hardware Used ut INN Hi DD M5 x 12 mm Screw x3 Q Fixing Bracket at a Phillips Screwdriver 12 Carefully lean the assembly and attach reflector A to mesh B with studs CC small flat washers BB on either side of reflector A and then wing nuts AA Gently return the assembly to the upright position Hardware Used AA Wing Nut C IU o Small Flat x6 Washer D Stud CO we 11 ASSEMBLY INSTRUCTIONS 13 Connect regulator to cylinder Install cylinder and secure with the propane block belt tightly Complete installation Note The propane gas and cylinder are sold separately Warning Use a standard 20 Ib propane cylinder only Use this fire feature only with a propane vapor withdrawal supply system See chapter 12 of the standard for storage and handling of liquefied petroleum gas ANS NFPA 58 or CSA B149 1 Natural Gas
25. w tops If excessive yellow flame is detected turn off fire feature and consult Troubleshooting on page 19 Re lighting Note For your safety control knob cannot be turned OFF without first depressing control knob in PILOT position and then rotating it to OFF 1 Turn control knob to OFF 2 Wait at least 5 minutes to let gas dissipate before attempting to relight pilot light Failure to follow this warning could cause a flash ignition or explosion 3 Repeat the Lighting steps on prior page A WARNING FOR YOUR SAFETY Fire feature will be hot after use Do not touch or move the fire feature until it is completely cooled approx 45 minutes Shut Down 1 Turn control knob clockwise to PILOT Normally burner will make a slight popping sound when extinguished Burner will extinguish but PILOT will remain ON 2 To extinguish PILOT depress control knob and continue to turn it clockwise to OFF 3 Turn cylinder valve clockwise to OFF and disconnect regulator when fire feature is not in use Note After use some discoloration of the emitter grid and reflector is normal Operation Checklist For a safe and pleasurable heating experience perform this check before each use Before Operating Ambiance Fire Feature is affected by wind Do not use is breeze is greater than 10 Miles Per Hour User is familiar with entire owner s manual and understands all precautions noted All components are properly assemble
26. x 12 mm bolts EE Hardware Used e M6 x 12 mm Bolt mm Q Wrench s X 6 Use Phillips screwdriver LL to secure the block belt L to the lower supports K with M5 x 12 mm screws DD Hardware Used DD M5 x 12 mm Screw 2 Phillips Screwdriver ASSEMBLY INSTRUCTIONS 7 Carefully install the glass tube with rubber ring at the bottom G between the center of top plate D and control box After the glass tube G is installed be sure to wipe off all fingerprints with a clean dry cloth 8 Inserting the glass tube C Insert the ceramic fiber Q to the quartz tube fixer Press the glass tube fixer to the glass tube Make sure the ceramic fiber is outside of glass tube Use Phillips screwdriver LL to secure the glass tube fixer C to the top plate D with M5 x 12 mm screws DD Hardware Used e M5 x 12 mm Screw Ant x3 Phillips e x 1 Screwdriver ASSEMBLY INSTRUCTIONS 9 Use Phillips screwdriver LL to install side panels H to bottom of assembly with M5 x 12 mm screws DD Note Do not cover the panel where the magnet is Hardware Used e M5 x 12 mm Screw eins 12 Phillips x 1 Screwdriver MTM LUTTE 10 Install the knob GG to M4x10 screw HH Hang the chain Il to the hole on the control box assembly J and put the pothook of front panel to the holes of bottom plate Hardware Used Knob X x 1 Screw M4 X 10
27. y behind ignitor button as needed 7 Remove and thoughouly clean control box assembly using compressed air annually if Ambiance Fire Feature pilot fails to light or as needed 18 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Open valve Insure fuel in tank Clean with compressed air or replace orifice or pilot tube Open gas line and bleed it pressing control knob in for no Pilot won t light Air in gas line more than 1 2 minutes or until you smell gas fully open cylinder i New igniter and replace leak check ing correctl Replace thermocouple Anti tilt switch could be faulty or wires not connected Replace anti tilt switch Connect wire properly properly Wait until the propane cylinder warms up and becomes unfrosted Blockage in main burner orifice Clear blockage with compressed air Turn control knob to ON Turn cylinder valve OFF and replace Cylinder with filled cylinder Note Fire feature operates at reduced efficiency below 40 F 5 C Pilot won t stay lit Q 1 EE s 2 8 2 8 Eo o Cdl Oo 9V Sic m z3 25 0 9 5 3 3 ole a Q c Ry 2o EZ S T Q 2 O O IC UO na lt C Ip 5 0 o FE 5 sab 5 2 slo 3 D lt o IO ols lt f Q D z5 zle la o 3 O s O18 co s D Q 2 lo O 2 D O oizls gt D e w Q Q O 2 Q x z o S 2 gQ Co lt T 2 D C lt C D 2 D lt pi 3 Q lt D El B o O m 3 So Z Main Burner wo
Download Pdf Manuals
Related Search