Instruction Manual - Davis Instruments
Contents
1. appears on the LCD replace the meter s 9V battery The battery compartment is located on the bottom of the meter s handle Open the compartment by sliding the battery compartment cover off in the direction of the arrow Replace battery and re install the battery compartment cover You as the end user are legally bound Battery ordinance to return all used batteries and accumulators disposal in the household garbage is prohibited You can hand over your used batteries accumulators at collection points in your community or wherever batteries accumulators are sold Disposal Follow the valid legal stipulations in respect of the disposal of the device at the end of its lifecycle Copyright 2009 Extech Instruments Corporation All rights reserved including the right of reproduction in whole or in part in any form 4 Model 42530 EU V2 4 5 092. thermometer will emit an audible warning and the OVER icon will be displayed on the LCD 3 Model 42530 EU V2 4 5 09 Field of View The meter s field of view is 8 1 meaning that if the meter is 20 3cm from the target the diameter of the object under test must be at least 2 54cm Other distances are shown below in the field of view diagram Refer to the chart printed on the meter for more information Diameter of Spot 10 1cm 5 08cm Laser Beam Sensor Beam e BLLQCM ainei Distance to Object Measurement Notes 1 The object under test should be larger than the spot target size calculated by the field of view diagram see diagram on previous page or on side of the meter 2 Ifthe surface of the object under test is covered with frost oil grime etc clean before taking measurements 3 Ifan object s surface is highly reflective apply masking tape or flat black paint before measuring 4 The meter may not make accurate measurements through transparent surfaces such as glass 5 Steam dust smoke etc can obscure accurate measurements 6 The meter compensates for deviations in ambient temperature It can however take up to 30 minutes for the meter to adjust to extremely wide ambient temperature changes 7 To find a hot spot aim the meter outside the area of interest then scan across in an up and down motion until the hot spot is located Battery Replacement When the low battery symbol E
3. User s Manual EXTECH INSTRUMENTS A FLIR COMPANY High Temperature InfraRed Thermometer with Laser Pointer MODEL 42530 CE Introduction Congratulations on your purchase of the Model 42530 IR Thermometer This thermometer makes non contact infrared temperature measurements at the touch of a button The built in laser pointer increases target accuracy while the backlit LCD and handy push buttons combine for convenient ergonomic operation Proper use and care of this meter will provide years of reliable service Safety e Use extreme caution when the laser pointer beam is on e Do not point the beam toward anyone s eye or allow the beam to strike the eye from a reflective surface CAUTI 0 N e Do not use the laser near explosive gases or in other TASER RADIATION potentially explosive areas DO NOT STARE INTO BEAM DIODE LASER lt 1mW Output at 675nm CLASS II LASER PRODUCT Specifications Infrared Thermometer Specifications Range Resolution 50 to 538 C 58 to 1000 F 0 1 C F lt 200 1 C F gt 200 Accuracy 2 of reading or 2 C 4 F whichever is greater Note Accuracy is specified for the following ambient temperature range 18 to 28 C 64 to 82 F General Specifications Display 3 digit backlit LCD display with function indicators Display rate 1 second approx Operating Temperature 0 to 50 C 32 F to 122 F Operating Humidity Max 80 RH Power S
4. upply 9V battery Automatic Power Off oe shuts off automatically after 7 seconds Weight 180g 6 35 oz Size 211 x 89 x 38mm 8 3 x 3 5 x 1 5 2 Model 42530 EU V2 4 5 09 Meter Description LCD Display Function Buttons Handle Grip Laser Pointer IR Sensor Measurement Trigger No a pon gt Battery Compartment Operating Instructions Hold the meter by its Handle Grip and point it toward the surface to be measured Pull and hold the red Trigger to turn the meter on and begin testing The display will light if the battery is good Replace the battery if the display does not light While measuring the SCAN display icon will appear in the upper left hand corner of the LCD While continuing to pull the Trigger a Push the red Laser button to turn on the laser pointer When the laser is on the laser icon will appear on the LCD over the temperature Aim the red beam approximately a half inch above the point of test pressing the Laser button again turns the laser off b Select the temperature units C or F using the blue C and F buttons c Push the yellow Backlight key to turn on the LCD backlighting function Release the Trigger and the HOLD display icon will appear on the LCD indicating that the reading is being held The meter will automatically power down after approximately 7 seconds after the trigger is released Overrange Indicator If the temperature being measured exceeds 538 C 1000 F the
Download Pdf Manuals
Related Search