Using the System
Contents
1. Find the brand name of the device in the tables starting on page 4 17 If the brand isn t listed see Scan for Device Codes on page 3 38 Press and hold the mode button until all the other mode buttons light up and then let go of the button The mode button flashes For example hold the TV mode button for a TV until all of the other mode buttons light When you let go the TV mode light will flash If you are repeating this procedure to program a combination device be sure to press the correct mode button for example if you have a TV VCR combination and you have already programmed the remote to control the TV press and hold the VCR mode button as described above For Aux mode only e Press O for a second TV e Press for a second VCR or DVD player e Press 2 for a tuner or amplifier This step is for programming which kind of device that should be programmed in Aux mode If you re not programming in Aux mode skip to step 5 Enter one of the three digit device codes from the table using the number buttons The three digit device code should be for the brand name of your device that you found in step 2 If you want to program limited mode press 1 If not skip to step 7 See Limited Mode for more information Press the Pound button If you entered the code correctly the mode button flashes three times Press the blank Power button to turn off the device If the device does not turn off2. User Guide CONTROL OTHER DEVICES WITH THE REMOTE CONTROLS This section describes how to use Remote Control 1 or Remote Control 2 to control with a TV a VCR or other devices For information on how to use the remote to control the receiver see Using the Remote Controls on page 3 1 You can set up both remote controls to control the satellite TV receiver and up three other devices each These devices can be a TV a VCR or DVD player and a third device Where the word remote is used in the following section it applies to both Remote Control 1 and Remote Control 2 REMOTE CONTROL MODES You can set the remote to four different modes to control the receiver or other devices When you get the remote it s already set up to control the receiver You must set up the remote to control a device like a TV or a VCR See Set Up the Remote to Control Other Devices below Use the remote control s mode buttons Sat satellite receiver TV for a TV VCR for a VCR or a DVD player and Aux auxiliary for a second TV a second VCR a tuner or an audio amplifier to set the remote to the right mode for the device To change the mode press the button for the device you want the remote to control The mode button lights for two seconds to show you ve set the remote to that mode LIMITED MODE You can program your remote control in limited mode to keep from accidentally changing the channel on your TV or VCR When you use the remot
3. ds to show you ve set the remote to TV mode Make sure you keep the remote in TV mode to use the buttons described here Note You can set up the remote to control a second TV in Aux mode the same way it controls the first TV in TV mode See Set Up the Remote to Control Devices beginning on page 3 36 Page 3 39 User Guide TV VIDEO BUTTON TV VIDEO If the TV has video input options use this button to switch the TV video input POWER POWER BUTTON Tr Press the TV Power button to turn the TV on or off MUTE BUTTON Press the Mute button to turn the TV sound on or off VOLUME BUTTON VOLUME Press this button to raise or lower the TV sound volume UP AND DOWN ARROW BUTTONS Use the Up and Down Arrow buttons to change channels on the TV Note These buttons do not change the channels on the TV if the remote control is in limited mode SELECT BUTTON The Select button works as the Enter button for a TV RECALL BUTTON Press the Recall button to go back to the last TV channel you watched ec Press it again to switch between the last two TV channels you watched al D gt p E NUMBER BUTTONS Q a Use the number buttons to directly enter a different channel 6 80 3 5 fo Note These buttons do not change the channels on the TV if the remote ss control is in limited mode 0 0 0 0 0 o fo 6 O 2 N Page 3 40 Using The System Control Other Devices With Th
4. e Remote Controls 3 CONTROL A VCR OR A SECOND VCR OR A DVD PLAYER Only the buttons described here control a VCR or DVD player Some of the buttons described here may not control your VCR or DVD player See the user s manual that came with your VCR or DVD player for information about the features VCR MODE BUTTON You must first set up the remote to control the VCR or DVD player See Set Up the Remote to Control Devices beginning on page 3 36 Then you must press the VCR mode button to set the remote to VCR mode The VCR mode button lights for two seconds to show you ve set the remote to VCR mode Make sure you keep the remote in VCR mode to use the buttons described here Note You can set up the remote to control a second VCR or DVD player in Aux mode the same way it controls the first VCR or DVD player in VCR mode See Set Up the Remote to Control Devices beginning on page 3 36 Note You must set the remote to VCR mode to set it up to control a DVD player TV VIDEO BUTTON TV VIDEO Use the TV Video button to switch the VCR between its TV mode and its VCR mode see your VCR user s manual for information POWER POWER BUTTON Press the blank Power button to turn the VCR on or off PAGE UP AND DOWN ARROW BUTTONS Use the Page Up and Down Arrow buttons to change channels on the VCR Note If you are using the remote control in limited mode the VCR will not change channels RECALL BUTTON Press th
5. e recall button to go back to the last VCR channel you used m Press it again to switch between the last two VCR channels you used RECALL Page 3 41 User Guide VCR BUTTONS e Press the Left arrow button to rewind a videotape or DVD e Press the down arrow button to pause a videotape or DVD Press this button or the Play button to go back to playing the tape or DVD e Press the right arrow button to fast forward a videotape or DVD e Press the up arrow button to stop playing or recording on a videotape or DVD e Press the Record button to record on a videotape or DVD e Press the select button to play or to go back to playing a videotape or DVD NUMBER BUTTONS Use the number buttons to enter channel numbers Note If you are using the remote control in limited mode the VCR will not change channels Page 3 42 T H E M E 5 B R W 5 E RECORD no 0 0 0 0 0 0 0 0 Z 3 a lt 3 D o oO O 6 2 ea 5 Using The System Control Other Devices With The Remote Controls 3 CONTROL A TUNER OR AMPLIFIER Only the buttons described here control a tuner or amplifier Some of the buttons described here may not control your tuner or amplifier Please see the user s manual that came with your tuner or amplifier for more information AUX MODE BUTTON You must first set up the remote to control the device See Set Up the Remote to Control Devices beginning on page 3 36 Then you must press t
6. e to control your TV in limited mode you will only be able to use the Power Mute and Volume buttons Also when you use the remote to control your VCR in limited mode you will only be able to use the power and VCR function buttons The section Setting Up the Remote to Control Other Devices has a step that tells the remote control to go into limited mode Note You can use Limited Mode for TV and VCR codes programmed in AUX mode SET UP THE REMOTES TO CONTROL OTHER DEVICES Over the next few pages we tell you how to use the remote to control a TV a VCR a DVD player a tuner or an amplifier To use the remote to control other devices you must first program it to control these other devices You can do this by either following the instructions in Set Up the Remote Control below or the Scan for Device Codes procedure described on page 3 38 If you are programming the remote to control a combination device such as a TV VCR or a VCR DVD program the remote control in one mode and then repeat the procedure in the other mode For example to program the remote to control a TV VCR using code 748 Follow the instructions to program the remote to control the TV using code 748 and then repeat the instructions for the VCR using the same code Page 3 36 Using The System Control Other Devices With The Remote Controls 3 SET UP THE REMOTE CONTROL Turn the device on Use the device s front panel buttons or its remote control
7. each digit of the device code with a pause between the groups of flashes A quick flash is for zero For example if the code is 570 the mode button flashes five times pauses flashes seven times pauses and flashes once quickly 3 For AUX mode only The first group of flashes tells you what the Aux mode controls A quick flash zero before the three digit code is for a TV one regular flash is for a VCR or DVD player and two flashes is for a tuner or amplifier For example if the TV code is 570 the Aux mode button flashes once quickly indicating 0 for TV pauses flashes five times pauses flashes seven times pauses and flashes once quickly REMOTE CONTROL BUTTONS CONTROL THE RECEIVER When you get the remote it s already set up to control the receiver However you must set up the remote to control the TV before you can use the Mute and Volume buttons For information on the remote buttons that control the receiver see Using the Remote Controls on page 3 1 CONTROL A TV OR A SECOND TV Only the buttons described here control a TV Some of the buttons described here may not control your TV Please see your TV user s manual for information about the TV s features TV MODE BUTTON You must first set up the remote to control the TV See Set Up the Remote wv to Control Other Devices beginning on page 3 36 Then you must press the TV mode button to set the remote to TV mode The TV mode button lights for two secon
8. go to step 10 If the code works the device should turn off Turn the device back on and try some other appropriate buttons to make sure they work If the code works for other buttons stop here Sometimes the blank Power button works when other buttons don t 10 If the code doesn t work redo steps 3 through 9 with another device code from the tables Try every code listed for you brand until one works for your device 11 If you can t find a code that works try Scan for Device Codes that follows Page 3 37 User Guide SCAN FOR DEVICE CODES If the code for your device is not listed in the tables starting on page 4 17 use this procedure to scan the remote control s memory for the device code 1 Turn the device on Use the device s front panel buttons or its remote control 2 Press and hold the mode button until all the other mode buttons light up and then let go of the button The mode button flashes For example hold the TV mode button for a TV until all of the other mode buttons light When you let go the TV mode light will flash 3 For Aux mode only e Press O for a second TV e Press 1 for a second VCR or DVD player e Press 2 for a tuner or amplifier This step is for programming which kind of device that should be programmed in Aux mode If you re not programming in Aux mode skip to step 4 4 For Aux mode only Press the Star button 5 Press the blank Power button This puts
9. he Aux mode button to set the remote to Aux mode The Aux mode button flashes once to show you ve set the remote to Aux mode Make sure you keep the remote in Aux mode to use the buttons described here Refer to TV Mode Button and VCR Mode Button as appropriate for the buttons available for use in AUX mode POWER BUTTON Press the blank Power button to turn the tuner or amplifier on or off MUTE BUTTON pos Press the mute button to turn the sound off or on VOLUME BUTTON Press the volume button to raise or lower the volume UP AND DOWN ARROW BUTTONS Use up and down arrow buttons to change channels on the tuner or amplifier ae SELECT BUTTON The select button works as the Input Select button for the tuner or amplifier Page 3 43 User Guide OTHER REMOTE CONTROL FEATURES SWITCH BETWEEN TV AND AUX DEVICE VOLUME CONTROL When you set up the remote to control a TV the mute and volume buttons control the TV volume However if you want to use the Aux mode to control a tuner or amplifier and the device has a volume setting you can set up the remote to control the device s volume instead of the TV volume To set the remote to control the device s volume Remote Buttons Menu Options Press and hold the Aux mode button for three seconds and then release it The aux mode button will blink search Press the Pound button Press the plus side of the Volume button Pres
10. s the 0 number button Press the Pound button The AUX mode button flashes three times Press the sat mode button Press the plus and minus sides of the _ volume button The device s volume changes and the aux mode button lights instead of the TV mode button Page 3 44 Using The System Testing The System 3 To set the remote back to control the TV volume Remote Buttons Menu Options Press and hold the TV mode button for three seconds and then release it The TV mode button will blink Press the Pound button Press the plus side of the Volume button Press the 0 number button Press the Pound button The TV mode button flashes three times Press the sat mode button Press the plus and minus sides of the ss volume button The TV s volume changes and the TV mode button lights instead of the AUX mode button
11. your remote in the scan mode 6 Press the up or down arrow button repeatedly until the device turns off As you press the up or down arrow button the remote is trying each code in the memory to see if it can turn off your device When the device turns off you have found a code that might work Note The mode button for the device will flash rapidly eight times when you ve scanned all the codes for that device 7 Press the Pound button This stores the code you found 8 Turn the device back on and try some other appropriate buttons to make sure they work Press the blank Power button to turn the device back on Try some other buttons to make sure they work Sometimes the blank Power button works when other buttons don t 9 Repeat this procedure until you ve tried all the codes You may need to repeat the scan to find the best code for your device Page 3 38 Using The System Control Other Devices With The Remote Controls 3 CHECK THE DEVICE CODES You can find out what device code you ve set for each remote control mode 1 Press and hold the mode button until all the other mode buttons light up and then let go of the button The mode button flashes For example hold the TV mode button for a TV until all of the other mode buttons light When you let go the TV mode light will flash 2 Press the Pound button twice Watch the mode light to determine your code The mode button flashes the number for
Download Pdf Manuals
Related Search