VIA VAB-600 User`s Manual
Contents
1. JM3 The jumper settings are shown below n Auto Power On default Figure 25 Power On select jumper Settings Pin1 Pin2 Pn Auto Power On default Open Close Close By power button Close Close Open Table 24 Power On select jumper settings 32 4 Hardware Installation 4 1 Installing 3G Module on Mini Card Slot Step 1 Align the notch of 3G module with the notch on Mini Card slot Then insert the 3G module into the Mini Card slot at 20 degree angle Figure 26 Inserting 3G module Step 2 Gently push down the rear side of the 3G module until the two screw holes on the module have been aligned and seated on the mounting holes of the board Then secure the 3G module with two 6mm screws Figure 27 Securing the 3G module 33 VAB 600 User Manual 4 2 Inserting 3G SIM Card on SIM Card Slot The onboard SIM card slot is automatically enabled when the 3G module without built in SIM card slot has been installed in the Mini Card expansion slot Step 1 Push back firmly the SIM card slot to unlock and open Pull up the slot and place the 3G SIM card Figure 28 Opening and inserting 3G SIM card Step 2 Gently close the slot by pulling down the slot containing the 3G SIM card and then carefully lock the SIM slot 34 VAB 600 User Manual Figure 29 Locking the 3G SIM card slot E 5 Driver Installation 5 1 Android Driver Supp2. 2 x Mini USB 2 0 Type AB ports 1 x Mini HDMI port Type C 1 x RJ 45 LAN port Fast Ethernet 1 x DC In jack 12V 24V o o 0 0 e Supported Operating System o Android 4 0 o Linux Kernel 3 0 8 e Operating Conditions o Operating Temperature e 0 C up to 60 C with heat spreader o Operating Humidity e 0 95 relative humidity non condensing o Storage Temperature Conditions e 20 C up to 70 C 90 e Form Factor o Pico ITX o 10cmx72cm e Compliance o CE o FCC VAB 600 User Manual 1 3 Layout Diagram Figure 1 Layout diagram of VAB 600 mainboard top and bottom view M amp K embedded Description PWR2 DC In connector SIM1 SIM card slot used for 3G module without built in SIM card slot CN3 Battery Charger connector optional BATI RTC Battery connector JM3 Power On Select jumper CN7 Front Panel pin header CN9 GPIO I C pin header SPI1 SPI Interface connector CN11 USB connector for WLAN USB module COM2 COM connector 2 COMI COM connector 1 CN8 Front Audio pin header B CN2 Mini Card expansion slot for USB connectivity 3G module 14 TS1 4 Wire Resistive Touch Screen connector 15 KPADI Key PAD connector 16 CNI CIR connector 17 CN13 Digital Video Output DVO connector 18 VM8950 Cortex A9 Single Core processor 19 4GB eMMC Flash memory 20 1GB DDR3 1066 DRAM memory Table 1 Layout diagram description table of VAB 600 mainboard
3. KT s o e Jala sen 3 1 4 Product Dimensions 3 5 mm hole lt 85 2 mm VAB 600 User Manual lt 67 mm lt 52mm 39 mm i 23 34 mm 11 mm Figure 2 Mounting holes and dimensions of the VAB 600 ge 7 75 mm f 2 21 mm 1 5 Height Distribution Height 7 75 mm Height 4 7 mm Height 5 75 mm Height 6 8 mm re r em Wem Height 2 00 mm Height 2 21 mm Height 1 61 mm Height with heat spreader 2 61 mm Figure 3 Height distribution of VAB 600 mainboard top and bottom side VAB 600 User Manual 2 UO Interface The VIA VAB 600 has a wide selection of interfaces integrated into the board It includes a selection of frequently used ports as part of the external I O coastline 2 1 External I O Ports Figure 4 External rear I O ports Description CN12 DC In jack SD1 Micro SD card slot USB2 Mini USB 2 0 port 2 type AB port USB2 Mini USB 2 0 port 1 type AB port DAWN HDMI1 Mini HDMI port 6 LAN1 RJ 45 Fast Ethernet LAN port Table 2 Layout diagram description table of external rear I O ports 2 1 1 DC In Jack The mainboard comes with a coaxial power connector on the real I O panel adjacent to the Micro SD slot The power connector carriers 12Vpe 24V bc external power input The specifications and pinout of the pow
4. Fast Ethernet LED color definition 14 2 3 Onboard Connectors 2 3 1 DC In Connector The mainboard has an onboard DC In 2 pin power connector to connect the DC In power cable The DC In power connector is an optional power connector in addition to the DC In jack on the rear IO panel This provides two methods for delivering 12Vpc 24Vpc to the mainboard The pinout of the DC In connector is shown below Figure 10 DC In connector diagram Pin Signal 1 12Vpc 24Vpe 2 _ GND Table 9 DC In connector pinout 15 2 3 2 SIM Card Slot The mainboard is equipped with a SIM card slot located on the top side of the board which can support a 3G SIM card Using the SIM card slot on VAB 600 requires a 3G module installed in the Mini Card expansion slot to enable the 3G function otherwise the SIM card slot is disabled The SIM card slot is designed only for 3G module without built in SIM card slot on it The SIM card slot is labeled as SIM1 The pinout of the slot is shown below Figure 11 SIM card slot diagram Pin Signal USIM_VCC USIM_RST USIM_CLK GND USIM_VPPSIM 7 USIM_DATA Table 10 SIM card slot pinout OJ Ri WI NH re 16 2 3 3 Battery Charger Connector Optional The mainboard is equipped with an onboard battery charger connector used for connecting the external cable for charging a rechargeable battery The battery charger connector is
5. Figure 15 GPIO and PC pin header diagram Pin Signal Pin Signal 1 VEC33 2 VEC By 3 GND 4 VSUS33 5 GPI20_CH 6 GPIO24_CH GPIO21 8 GPIO25 9 GPIO_22 10 GPIO_26 11 GPIO_23 12 GPIO_27 13 I2COSDA 14 I2COSCL Table 14 GPIO and PC pin header pinout 20 2 3 7 SPI Flash Connector The mainboard has one 8 pin SPI flash connector By connecting to the SPI BIOS programming fixture the SPI Serial Peripheral Interface flash connector can update the SPI flash ROM The connector is labeled as SPI1 The pinout of the connector is shown below Figure 16 SPI Flash connector diagram 5 Signal SFCS1 Reserved SFDO SFDI SFCLK SFCSO GND VPROG_SP1 3 3V Table 15 SPI Flash connector pinout INIA BR Ww dO Re 21 2 3 8 USB Connector The mainboard includes one onboard USB connector designed for connecting the wireless LAN USB module The connector is labeled as CN11 The pinout of the connector is shown below Figure 17 USB connector diagram Pin Signal 5V USBH3 USBH3 GND USB_WIFI_LED 6 GPIO_4 Table 16 USB connector pinout oO BR WwW Nh re 22 2 3 9 COM Connector There are two onboard COM connectors on the top side of the mainboard The COM connectors labeled as COM1 and COM are used to attach additional COM port that supports Tx Rx The pinout of t
6. 33 40 GND 25 MIX Embedded 41 VSUS33 42 LED_WWANI 43 GND 44 LED WLANI 5 46 LED_WPANI ay A8 1 5V 49 50 GND a 52 VSUS33 Table 19 Mini Card slot pinout 26 VAB 600 User Manual 23 12 4 Wire Resistive Touch Screen Connector The mainboard is equipped with a touch screen connector for connecting the 4 wire resistive touch panel The touch screen connector is labeled as TS1 The pinout of the connector is shown below Figure 21 4 Wire Resistive Touch Screen connector diagram Pin Signal 1 TPXP 2 TPYP 3 TPXM 4 TPYM Table 20 4 Wire Resistive Touch Screen connector pinout 27 VAB 600 User Manual 23 13 Key PAD Connector The mainboard is equipped with a Key PAD connector for connecting the keypad device The connector is labeled as KPAD1 The pinout of the connector is shown below Figure 22 Key PAD Connector diagram Pin Signal 1 VCC33 2 KPADROWO 3 KPADROW1 4 KPADROW2 5 6 KPADROW3 KPADROW4 4 GND Table 21 Key PAD connector pinout 28 VAB 600 User Manual 2 3 14 CIR Connector The mainboard provides a CIR Consumer Infrared Receiver connector on the top side of the board The CIR connector is used to connect the infrared receiver module to enable infrared wireless interface The pinout of the CIR connector is shown bel
7. 5 854 South Korea TEL 82 2 571 2986 FAX 82 2 571 2987 Email embedded via korea com
8. M amp K embedded USER MANUAL VAB 600 Pico ITX Cortex A9 Board 1 03 11272014 175300 Copyright Copyright 2014 VIA Technologies Incorporated All rights reserved No part of this document may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means electronic mechanical magnetic optical chemical manual or otherwise without the prior written permission of VIA Technologies Incorporated Trademarks All trademarks are the property of their respective holders Disclaimer No license is granted implied or otherwise under any patent or patent rights of VIA Technologies VIA Technologies makes no warranties implied or otherwise in regard to this document and to the products described in this document The information provided in this document is believed to be accurate and reliable as of the publication date of this document However VIA Technologies assumes no responsibility for the use or misuse of the information including use or connection of extra device equipment add on card in this document and for any patent infringements that may arise from the use of this document The information and product specifications within this document are subject to change at any time without notice and without obligation to notify any person of such change VIA Technologies Inc reserves the right the make changes to the products described in this manual at any time
9. a 25 2 3 12 4 Wire Resistive Touch Screen Connector 27 23 13 Key PAD COnMe Ctl E 28 23 14 e TU E 29 2315 OVO COMMS OR sunnum a E aana il 30 VAB 600 User Manual 3 Jumper 32 3 1 Power On Select Jumper 32 4 Hardware Installation aaaaaanaaaaaavaaavnnasnnannannnaannannnannanannananananaanaa 33 4 1 Installing 3G Module on Mini Card Slot 33 4 2 Inserting 3G SIM Card on SIM Card Slot 34 5 Driver Installati n E 36 5 1 Android Driver Support 36 5 2 Linux Driver ee E 36 Appendix A Mating Pin Header and Connector Vendor Lists 37 A L VAB 600 MainbOard 45 sinp ele a nat 37 vi VAB 600 User Manual Lists of Figures Figure 1 Layout diagram of VAB 600 mainboard top and bottom view 5 Figure 2 Mounting holes and dimensions of the VAB 600 7 Figure 3 Height distribution of VAB 600 mainboard top and bottom side 8 Figure 4 External rear I O ports 9 Figure 2 lr Jok EISE geseet 10 Figure 6 Micro SD Card slot diagram cee eee ee eset aee eaaa aee eaaa 11 Figure 7 Mini USB port diagram cee nnrir 12 Figure 8 Mini HDMI patologia 13 Figure 9 Fast Ethernet port diagram 14 Figure 10 DC in connector diagramas nanadusl sassksa tia s s a skik aaa 15 Figure 11 SIM card slot diagram eisiiissseeieiiesssertiissssrrresessrrrreessserrrrrersee
10. anging eaoin 11 Table 5 Mini USB 2 0 port piNOUt iii 12 Table 6 Mini HDMI port Ginet 13 Table 7 Fast Ethernet port pinoUt ssori iersinii i i 14 Table 8 Fast Ethernet LED color definition unala alas l alls taS Klassi 14 Table 9 DC In connector GDinout s sieeiieeiieesiessiiesiiesiieriiesitssitesittsitssrttrirtsirennrtns 15 Table 10 SIM tara Slot DING sasana inaa naga iaia aa 16 Table 11 Battery Charger pinout essiensa 17 Table 12 RTC Battery connector pinoUt sssrinin 18 Table 13 Front Panel pin header PiNOUt aasssaeian sangkan iak a meg anah Lk ka 19 Table 14 GPIO and PC pin header Ginout 20 Table 15 SPI Flash connector pinOUt iii 21 Table 16 USB connector PINOUt sawana panga anaa gayeng bema naak neg ragangane 22 Table 17 COM Connector pinout 1n 1 un uuadsisiissalksnsansudnnusnnndumuu 23 Table 18 Front audio pin header Pinout cece ii 24 Table 19 Mini Card slot pinout as tssseiiinsnrienisiniensa o 26 Table 20 4 Wire Resistive Touch Screen connector pinout 27 Table 21 Key PAD connector Dinout iii 28 Table 22 CIR connector ln EE 29 Table 23 DVO connector el 31 Table 24 Power On select jumper settings iaanana eee eset eaaa aee 32 Table 25 VAB 600 pin header and connector vendor lists 37 viii VAB 600 User Manual 1 Product Overview VIA VAB 600 is an ultra compact Pico ITX and highly in
11. e damage or electrical shock Do not place anything over the power cord Do not cover the ventilation holes The openings on the enclosure protect the equipment from overheating VAB 600 User Manual Box Contents VAB 600 1 x VAB 600 embedded board with WM8950 Cortex A9 processor 1 x DC In cable 1 x Front Panel cable 1 x Front Audio cable 1 x COM connector cable 1 x USB cable for optional WLAN USB module OOOOOO VAB 600 User Manual Table of Contents 1 Product OverviewW 1 1 1 KeyFeatures i ca 1 1 2 Product SpecificatiONS ii 3 1 3 Layout Diagram R rang baga bena an naga add mane elica 5 1 4 Product Dimenslons reinan 7 15 Elei e 8 2 VO dur Ee EE 9 2 1 External NO POS erer e Lia Saar 9 2 1 1 DOM ACK sisanne naga a aaa aaa a a an a naa ba a aaa ahs le 10 2 2 Micro SD Card Slot a isan csi ae nt eine eee nisi 11 2 2 1 Mini OSB ZO POPE nn ees ces GA DASA aa NAK a SADE SETA a AE oa 12 2 2 2 Mini HDMI Port 13 2 2 3 RJ 45 LAN port Fast Ebenen 14 23 Onboard Gonnectors ai a 15 2 3 1 DC In Connector 15 2 3 2 EE KI 16 2 3 3 Battery Charger Connector Optional 17 2 3 4 RTC Battery Connector eerste nahi kanga pena sa mapaga nai ger raganira 18 2 3 5 Front Panel Pin Header 19 2 3 6 GPIO and PC Pin Header 20 2 3 7 SPI Flash Connector 21 2 3 8 DUSEL 22 2 3 9 COM COMME COR E 23 2 3 10 Front Audio Pin Header 24 23 11 Mini Card Slot aaa eci aLaa
12. efined in the HDMI specification The Mini HDMI port is for connecting to HDMI displays The pinout of the Mini HDMI port is shown below Figure 8 Mini HDMI port diagram Pin Signal Pin Signal 1 GND 2 LCD1DO2 3 LCD1DO2 4 GND 3 LCD1IDO1 6 LCD1DO1 Vi GND 8 LCD1DO0 9 LCD1DO0 10 GND 11 LCD1CLK 12 LCD1CLK 13 GND 14 HDMI_CECIN 15 DDESEL 16 DDCSDA 17 18 VCC_5V 19 HPD Table 6 Mini HDMI port pinout Aa VAB 600 User Manual 2 2 3 RJ 45 LAN port Fast Ethernet The integrated 8 pin Fast Ethernet port is using an 8 Position 8 Contact 8P8C receptacle connector commonly referred to as RJ 45 The Fast Ethernet ports are controlled by VIA VT6113 10 100 Base TX PHY chip controller The pinout of the Fast Ethernet port is shown below Figure 9 Fast Ethernet port diagram Pin Signal TD TD RD REGOUT REGOUT RD GND 8 GND Table 7 Fast Ethernet port pinout NICI HSN Bag The RJ 45 port has two individual LED indicators Located on the front side to show its Active Link status and Speed status Link LED Active LED Left LED on RJ 45 connector Right LED on RJ 45 connector Link Off Off Off Speed_10Mbit The LED is always On in dark color Flash in Yellow or Orange color Speed_100Mbit The LED is always On in Red color Flash in Yellow or Orange color Table 8
13. er connector are shown below 3 7 mm 1 3 mm Figure 5 DC In jack diagram Physical Specifications Outer Diameter 3 7 mm Inner Diameter 1 3mm Barrel Depth 8 25 mm Electrical Specifications Input Voltage 12V 24V Table 3 DC In jack specifications 10 2 2 Micro SD Card Slot The Micro SD card slot is located on the rear I O panel it offers expandable storage Figure 6 Micro SD Card slot diagram 5 Signal SDODATA2 SDODATA3 SDOCMD VDD 3 3V SDOCLK GND SDODATAO SDODATA1 9 SDO CD Table 4 Micro SD Card slot pinout D Jill ki Ww N 11 2 2 1 Mini USB 2 0 Port VAB 600 User Manual There are two integrated Mini USB 2 0 ports Located on the rear I O panel The Mini USB 2 0 interface port gives complete Plug and Play and hot swap capabilities for external devices and it complies with USB UHCI rev 2 0 Each Mini USB port uses the USB Type AB receptacle port connector The pinout of the typical Mini USB port is shown below Figure 7 Mini USB port diagram USB1 USB2 Pin Signal Pin Signal 1 VCC 5V 1 VCC 5V 2 USBH1 2 USBH2 3 USBH1 3 USBH2 A ID GND 4 ID GND 5 GND 5 GND Table 5 Mini USB 2 0 port pinout 12 VAB 600 User Manual 2 2 2 Mini HDMI Port The integrated 19 pin Mini HDMI port uses an HDMI Type C receptacle connector as d
14. he COM connectors are shown below Figure 18 COM connector diagram COMI COM2 Pin Signal Pin Signal 1 TXDO 1 TXD2 2 RXDO 2 RXD2 3 GND 3 GND 4 N A 4 N A 5 N A 5 N A Table 17 COM connector pinout 23 VAB 600 User Manual 2 3 10 Front Audio Pin Header The mainboard has a front audio pin header for connecting the Line Out and Mic In jacks The pin header is labeled as CN8 The pinout of the pin header is shown below Figure 19 Front audio pin header diagram Pin Signal Pin Signal 1 N A 2 GND 3 N A 4 MICIN1 5 LINEOUT_R 6 MICIN2 7 LINEOUT_L 8 HP_DET Table 18 Front audio pin header pinout 24 SE Mini Card Slot VAB 600 User Manual The VAB 600 mainboard is equipped with a Mini card expansion slot labeled as CH The Mini card slot is used to attach the USB connectivity 3G module to provide 3G function The pinout of the slot is shown below Figure 20 Mini Card slot diagram Pin Signal Pin Signal 1 2 VSUS33 3 4 GND 5 6 1 5V Fi 8 USIM_VCC 9 GND 10 USIM_DATA 11 12 USIM_CLK 13 14 USIM_RST 15 GND 16 USIM_VPP 17 18 GND 19 20 W_DISABLE_1 21 GND 28 PEX1_RST 23 24 VSUS33 25 26 GND 27 GND 28 1 5V 29 GND 30 I2COSCL 31 32 I2COSDA 33 34 GND 35 GND 36 USBHD_0 37 GND 38 USBHD_0 39 VSUS
15. i USB 2 0 ports 1 2 Product Specifications e Processor o WonderMedia WM8950 Cortex A9 Single Core 800MHz e System Memory o Onboard 1GB DDR3 SDRAM 1066 e Graphics o Built in 2D 3D Graphics Engine to support OpenGL ES2 0 o Built in Video Multi standard Decoder to support MPEG2 MP HL H 264 BP MP HP L4 0 VC 1 SP MP AP VP8 and JPEG MJPEG Decoding e Flash Storage o Onboard 512KB SPI Flash ROM for Boot Load o Onboard 4GB eMMC Flash memory e Ethernet o VIA VT6113 10 100 base TX PHY Chip e Audio o VIA VT1603A DS Audio Codec e WiFi module o Optional VIA VNT9271B6050 WLAN module shared with one USB port e Onboard I O Connectors 1 x DVO connector for TTL or LVDS display corresponding daughter card is required 2 x COM connectors supports Tx Rx 1 x Micro SD card slot 1 x RTC Battery connector 1 x USB 2 0 connector for wireless LAN USB module 1 x SPI connector for programming SPI flash ROM 1 x Mini Card expansion slot for USB connectivity 3G module 1 x SIM card slot used for 3G module without built in SIM card slot 1 x Key PAD connector 1 x CIR connector 1 x Front Audio pin header 1 x Front Panel pin header o oo 0 0 0 0 0 oo 0 0 1 x 4 Wire Resistive Touch Screen connector through VT1603A 1 x GPIO and BC pin header for one DC pair and eight GPIOs 1 x 12V 24V DC In onboard connector 1 x Battery charger connector with Smart Battery function manufacturing option o o o 0 e Back Panel I O
16. ini Card slot 52 DRAGONSTATE 0710A0BA68B SIM1 SIM Card slot 7 FOI 7111S2015X02LF CN8 Front Audio pin header 8 PINREX 22W 97 04GB21 COM 1 amp 2 COM connectors 5 ACES 85204 0500L CN11 USB connector 6 ACES 87213 0600G SPIL SPI Flash connector 8 ACES 87213 0800G CN9 GPIO C pin header 14 PINREX 22W 97 07GB21 CN7 Front Panel pin header 6 PINREX 22W 97 03GB21 CN3 Battery Charger connector 5 ACES 50299 00501 001 CN13 DVO connector 50 ACES 50501 05040 001 JM3 Power On Select jumper k NELTRON 2199SA 03G 301523 BAT1 RTC Battery connector 2 NELTRON 1251R 02 SM1 TR F5 Table 25 VAB 600 pin header and connector vendor Lists 37 Taiwan Headquarters 1F 531 Zhong Zheng Road Xindian Taipei 23148 Taiwan TEL 886 2 2218 5452 FAX 886 2 2218 5453 Email embedded via com tw China Tsinghua Science Park Bldg 7 No 1 Zongguancun East Road Haiden District Beijing 100084 China TEL 86 10 59852288 FAX 86 10 59852299 Email embedded viatech com cn USA 940 Mission Court Fremont CA 94539 USA TEL 1 510 683 3300 FAX 1 510 687 4654 Email embedded viatech com Japan 3 15 7 Ebisu MT Bldg 6F Higashi Shibuya ku Tokyo 150 0011 Japan TEL 81 3 5466 1637 FAX 81 3 5466 1638 Email embedded viatech co jp E Europe Zei KA In den Dauen 6 53117 Bonn Germany TEL 49 228 688565 0 FAX 49 228 688565 19 Email embedded via tech eu Korea 2F Sangjin Bldg 417 Dogok Dong Gangnam Gu Seoul 13
17. labeled as CN3 The connector pinout is shown below Figure 12 Battery Charger connector diagram Pin Signal d Voltage detect 2 I2COSCL 3 I2COSDA 4 GND Temperature Detect Table 11 Battery Charger pinout 17 2 3 4 RTC Battery Connector The mainboard is equipped with an onboard RTC battery connector used for connecting the external cable battery that provides power to the 32 768KHz crystal oscillator for Real Time Clock RTC The RTC battery connector is labeled as BAT1 The connector pinout is shown below Figure 13 RTC Battery connector diagram Pin Signal 1 VBAT 2 GND Table 12 RTC Battery connector pinout 18 2 3 5 Front Panel Pin Header The front panel pin header block consists of 6 pins It provides access to the system power LED power switch and shut down switch The front panel pin header is labeled as CN7 The pinout of the pin header is shown below Figure 14 Front Panel pin header diagram Pin Signal Pin Signal 1 Pop LED 2 GND 3 PWRBTN 4 GND 5 RESET1 6 GND Table 13 Front Panel pin header pinout 19 VAB 600 User Manual 2 3 6 GPIO and PC Pin Header The GPIO and BC combination pin header block labeled as CN9 is used for connecting the PC device and eight General Purpose Input and Output The pinout of the combination pin header is shown below lo
18. opriate battery specified for this product Do not re use recharge or reheat an old battery Do not attempt to force open the battery Do not discard used batteries with regular trash Discard used batteries according to local regulations Safety Precautions OOO OTEO CE OOOO Always read the safety instructions carefully Keep this User s Manual for future reference All cautions and warnings on the equipment should be noted Keep this equipment away from humidity Lay this equipment on a reliable flat surface before setting it up Make sure the voltage of the power source and adjust properly 110 220V before connecting the equipment to the power inlet Place the power cord in such a way that people cannot step on it Always unplug the power cord before inserting any add on card or module If any of the following situations arises get the equipment checked by authorized service personnel e The power cord or plug is damaged Liquid has penetrated into the equipment The equipment has been exposed to moisture e e e The equipment has not worked well or you cannot get it work according to User s Manual e The equipment has dropped and damaged e The equipment has obvious sign of breakage Do not leave this equipment in an environment unconditioned or in a storage temperature above 60 C 140 F The equipment may be damaged Do not leave this equipment in direct sunlight Never pour any liquid into the opening Liquid can caus
19. ort The VIA VAB 600 mainboard is compatible with Android 4 0 operating systems The latest drivers can be downloaded from the VIA Embedded website at www viaembedded com 5 2 Linux Driver Support The VIA VAB 600 mainboard is highly compatible with Linux Kernel 3 0 8 Support and drivers are provided through various methods including e Drivers provided by VIA e Using a driver built into a distribution package e Visiting www viaembedded com for the latest updated drivers e Installing a third party driver For OEM clients and system integrators developing a product for Long term production other code and resources may also be made available Contact VIA Embedded to submit a request 36 MIX Embedded VAB 600 User Manual Appendix A Mating Pin Header and Connector Vendor Lists The following tables listed the mating pin headers and connectors vendor Lists A 1 VAB 600 Mainboard Label Function Pins Vendor Part No CN12 DC In jack 2 KYOYAKU KYP 020 06MB PWR2 DC In connector NELTRON 2317RJ 02 SD1 Micro SD card slot KTS C40KDH 081T 12DL USB 1 amp 2 Mini USB AB Type ports NELTRON 5075ABMR 05 SM CR HDMI1 Mini HDMI port 19 FREEPORT 60U019S 354N A1 LAN1 RJ 45 Fast Ethernet port 8 UDE RS3 26401D1F CNI CIR Receiver Module connector 3 ACES 88460 0301 KPADI Key PAD connector 7 ACES 88460 0701 TSI Touch Screen connector 4 ACES 50500 00441 001 CN2 M
20. ow Figure 23 CIR connector diagram Pin Signal 1 VSUS33 2 GND 3 CIR Table 22 CIR connector pinout 29 2 4 LA DVO Connector VAB 600 User Manual The DVO Digital Video Output connector works as an interface for multi display devices This connector allows the mainboad to connect an additional daughter card which is required for a certain display such as TTL or LVDS display The DVO connector is labeled as CN13 The pinout of the connector is shown below EE EE Figure 24 DVO connector diagram Pin Signal Pin Signal i VEC33 26 LD15 2 VCC33 27 GND 3 VCC33 28 LD16 4 5VIN 29 LD17 5 5VIN 30 LD18 6 5VIN 31 LD19 7 VIN DC In Battery 32 LD20 8 VIN DC In Battery 35 LD21 9 GND 34 LD22 0 LDOO 35 LD23 1 LDO1 36 GND 12 LD02 37 DVP1CLK 3 LD03 38 GND 4 LD04 39 DVPHS 5 LDOS 40 DVPVS 6 LD06 41 DVPDE Fi LD07 42 PWMOUTO 18 GND 43 TTL_RST 30 VAB 600 User Manual 19 LD08 44 I2COSCL 20 LDO9 45 I2COSDA 21 LD10 46 DVO_CLK 22 LD11 47 DVO_DATA 23 LD12 48 LVDSENBL 24 LD13 49 LVDSENVDD 25 LD14 50 GND Table 23 DVO connector pinout EN VAB 600 User Manual 3 Jumper 3 1 Power On Select Jumper The Power On Select jumper is used to enable or disable the auto power On function when plug in the power adaptor The jumper is labeled as
21. rrrrr t 16 Figure 12 Battery Charger connector diagram 17 Figure 13 RTC Battery connector diagram iii 18 Figure 14 Front Panel pin header diagram 19 Figure 15 GPIO and PC pin header diagram 20 Figure 16 SPI Flash connector diagram eee eset etnies 21 Figure 17 USB connector diagram 22 Figure 18 COM connector diagram i 23 Figure 19 Front audio pin header diagram eee eset eaaa aee eaaa 24 Figure 20 Mini Card slot diagram cece tees eset eaaa eee eaaa naen 25 Figure 21 4 Wire Resistive Touch Screen connector diagram 27 Figure 22 Key PAD Connector diagram 28 Figure 23 CR connector dagr aM saanak kana sla AK ANAA BANA kaba kan gg USR 29 Figure 24 DVO connector diagram 30 Figure 25 Power On select JUMPEN sasapan ana 32 Figure 26 Inserting 3G MOduUle iii 33 Figure 27 Securing the 3G MOGUL asana aaa biangane nan an asa aa skam 33 Figure 28 Opening and inserting 3G SIM Card 34 Figure 29 Locking the 3G SIM card Slot 35 vii VAB 600 User Manual Lists of Tables Table 1 Layout diagram description table of VAB 600 mainboard 6 Table 2 Layout diagram description table of external rear I O ports 9 Table 3 DC In jack specifications ee ee eea eaaa eaaa eee aee eaaa 10 Table 4 Micro SD Card Slot PinOUte cece anana aga eea gi
22. tegrated ARM based board measuring 10 cm x 7 2 cm Powered by 800MHz WM8950 Cortex A9 single core processor with built in 3D 2D graphics engine and video multi standard decoder It is also compatible with Android 4 0 and Linux Kernel 3 0 8 operating systems and provides an impressive rear and onboard I O in a compact form factor The ultra compact VAB 600 mainboard is optimized for both performance and power to meet the high end demands of advanced industrial in vehicle and multimedia applications while offering extremely low power consumption It suits with various domain applications such as Tablet PC Industrial PC Digital Signage Thin Client and etc 1 1 Key Features e Powered by WM8950 Cortex A9 Single Core 800MHz processor e Integrated graphics processing GPU for 3D 2D graphics acceleration e Compatible with Android 4 0 and Linux Kernel 3 0 8 operating system e Small form factor and low power design e Fanless and ultra low power consumption e Accept wide range of DC power input 12V 24V e 4GB onboard eMMC Flash memory e Onboard DVO Digital Video Output for TTL or LVDS display e Support 4 wire resistive touch screen interface connector e Support Mini Card expansion slot for USB connectivity 3G module VAB 600 User Manual e Support SIM card slot for 3G SIM card used for 3G module without built in SIM card slot e Support Micro SD Card slot for expandable storage e Support RJ 45 LAN Fast Ethernet Mini HDMI and Min
23. without prior notice Regulatory Compliance FCC A Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a class A digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his personal expense Notice 1 The changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to o perate the equipment Notice 2 ielded interface cables and A C power cord if any must be used in order to comply with the emission Limits n Notice 3 The product described in this document is designed for general use VIA Technologies assumes no responsibility for the conflicts or damages arising from incompatibility of the product Check compatibility issue with your Local sales representatives before acing an order go Tested To Comply With FCC Standards FOR HOME OR OFFICE USE Battery Recycling and Disposal OOOOO Only use the appr
Download Pdf Manuals
Related Search