Home

Ultra High Definition LED

1. STX CMD Ex CMD Length Data ETX 1 byte 1 byte 1 byte 1 byte Variable 1 byte Group ID Multi ID Other Data 1 byte 1 byte N byte tisa commanding format to LCD The command will be effective only for the set of the designated ID STX 0x02 Code for initiation It means the beginning of Protocol Fixed value CMD Code for actual command Variable ExCMD Code for expanded code Fixed value 0x01 Length The length of Data area Variable 0 255 Data The areas for ID and the other Data Variable Group Multi ID Code for distinguishing LCD sets Group ID 0x01 Multi ID 0x01 Fixed ETX 0x03 Code for the end of Protocol Fixed value 2 2 Receive From LCD Length Data Check Sum ETX 1 byte 1 byte 1 byte 1 byte Variable 1 byte 1 byte Group ID Multi ID Other Data 1 byte 1 byte N byte Response format to a certain command from the designated set among LCD sets The difference from Send to LCD is Check sum STX 0x02 Code for initiation It means the beginning of Protocol Fixed value CMD Code for actual command Variable ExCMD Code for expanded code Fixed value 0x01 Length The length of Data area Variable 0 255 Data The areas for ID and the other Data Variable ID Code for distinguishing LCD sets Group ID 0x01 Multi ID 0x01 Fixed Check sum Execute Not ope
2. Performance Audio Information L L L i L L i L i L L L 1 L i L i L L L i L L L L 96 99 Click the position of the display of blue color in the Desktop layout part in CCC RADEON a AMDA gt Pinned gt Presets Desktop Management Common Display Tasks AMD Eyefinity Multi Display gt My Digital Flat Panels gt Video Gaming gt Performance gt Audio gt Information Catalyst Control Center Creating and Arranging Desktops Preferences 3 Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware In the group below click the position corresponding to the display lit in blue e Then the other one of 4 displays is turned on with blue color again In the same manner click the position of the display of blue color in the Desktop layout part in CCC again 60 When the display arrangement is completed and the screen is correctly displayed click Done RADEON GRAPHICS Catalyst Control Center AMDA Preferences e Creating and Arranging Desktops 4 7 Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware gt Pinned Presets In the gro
3. aa Ka n NEZ VEN NSEZ 04 Cable Connection e Do not connect or disconnect the signal cables while the display and the peripheral devices are turned on e The power must be turned off before connecting the signal cables or the peripheral devices e The power cord must be firmly inserted to prevent unexpected disconnection IR A S RS232 LAN HDMI2B HDMI1C HDMI2C 2 USB ACINPUT ON OFF DVD player with HDMI out DVD player with HDMI out DVD player with HDMI out DVD player with HDMI out USB Cable Touch Model Only DVD player DVD player DVD player with HDMI out with HDMI out with HDMI out DVD player with HDMI out RS 232 LAN Cable Cross cable LAN Cable Direct cable HUB or Router Ethernet Control PC LAN Cable Direct cable 15 s 05 How to use Remote Controller 1 MENU button OSD MENU will be displayed by pressing MENU button 9 PICTURE BRIGHTNESS CONTRAST SCREEN TINT COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B Ww Ou can s
4. Your displays have been reconfigured Do you want to keep these changes Reverting in 15 seconds e Click the display No 3 in the Display selection part with the right button of your mouse to popup the window and select Duplicate RADEON GRAPHICS Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware To configure a desktop click the triangle W on the desktop below Click and drag desktops to arrange them Common Display Tasks AMD Eyefinity Multi Display _ My Digital Flat Panels em Please select a display 49 When you see the massage Please select a desktop to duplicate on the screen as shown below select the display No 1 in the Desktop layout part RADEON GRAPHICS Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware gt Presets La Please select a desktop to duplicate s Desktop ig Management Common Display Tasks v AMD Eyefinity Multi Display My Digital Flat Panels 08 0 e The screen will be turned off for a moment and turned on After the screen is turned on the following caution window will be displayed Then select Yes Your displays have been reconfigured
5. When SCREEN is selected press MENU button to move to the sub menu HPOSITION V POSITION ASPECT RATIO VIDEO MUTE and SCREEN MODE can be adjusted 3 EXIT MENU Press Exit button to exit from the menu so gt H POSITION gt ASPECT RATIO Configuration e Adjust the horizontal position of the display image on the screen e Adjust screen ratio e FULL All the input will be displayed with the screen ratio of 16 9 1 Select H POSITION from SCREEN menu ASPECT All the input will be displayed with their original screen ratio Adjust H POSITION values with wb buttons after selecting H POSITION 1 Select ASPECT RATIO from SCREEN menu E Move to the sub menu by pressing MENU button after selecting ASPECT RATIO PICTURE H POSITION V POSITION PICTURE H POSITION ASPECT RATIO VIDEO MUTE V POSITION SETUP A eet SCREEN ASPECT RATIO SCREEN MODE SCREEN RESET VIDEO MUTE SETUP B SETUP A SCREEN MODE Vv SCREEN RESET You can see the screen more clearly When you choose a lighter around SETUP B Vv You can see the screen more clearly When you choose a lighter around 2 EXITMENU Press Exit button to exit from the menu 2 Select ASPECT RATIO value 16 9 or 4 3 screen ration can be selected Use ft buttons to move into the sub menu and press MENU button again to gt V POSITION select the screen ratio e Adjust the vertical position of the display
6. HDMIID HDMDD RS232 LAN A S IR ACINPUT ON OFF HDMI1A HDMI2A HDMI1B HDMI2B HDMIIC HDMI2C HDMI2D RS232 LAN A S IR l Fd m E Display input selection e The input mode of the display unit should be configured as described below e If the cable connection was made with the input group 1 HDMI1A HDMI1B HDMI1C HDMI1D then press Group 1 UHD button in the remote controller Press Group 2 UHD button for the input group 2 HDMI2A HDMI2B HDMI2C HDMI2D E Graphic card configuration e Compose one full screen image with 4 separate screens with the graphic configuration software provided by the graphic card makers e Please refer to the user guide of each graphic card maker or contact to the company for detailed usage of the graphic card he configuration for the optional ORION PC is as follows As you connect the output ports of the PC to the input ports in the display you will see the following screen However the screen image may be different due to various cable connection or PC settings In case you do not have the same screen image like following screen image you still configure the display as described below E em e Click the right button of your mouse on the desktop to pop up the menu and select Catalyst Control Center CCC PA a Catalyst Control enter View Ld Sort by d
7. Press Exit button to exit from the menu zn 07 User guide for UHD Graphic e This display supports UHD Ultra High Definition Resolution 3840 X 2160 resolution e This display unit can display UHD images by collecting 4 different FHD Full High Definition Resolution 1920 X 1080 input simultaneously from a PC that can make 4 separate FHD output So it requires a graphic card that has at least 4 FHD output ports and capable to compose one screen image with the 4 separate input e g AMD Eyefinity e You may use any graphic card that satisfies above mentioned condition besides the recommended MSI 7970 However all the output ports must be the same interface e g 4 HDMI ports 4 DVI ports or 4 DP ports etc e Even though the output ports are not same it still can display UHD image but the screen image may not be displayed properly e g 2 DVI ports amp 2 DP ports 9 a hb Mini DP Mini DP DVI D Mini DP Mini DP MSI Radeon HD 7970 R7970 Lightning D5 3GB v E Cable connection e Connect the output ports of the graphic card and the input ports of the display using the input port UHD group 1 HDMI1A HDMI1B HDMI1C HDMI1D or UHD group 2 HDMI2A HDMI2B HDMI2C HDMI2D as shown below Simply 4 outputs from the graphic card should be connected to the input ports in a same group UHD group 1 or UHD group 2 ACINPUT ON OFF X HDMIA HDMI2B HDMIIC HDMI2C
8. Value 0x02 0x80 0x01 0x04 Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Control Value The value for OFF is 0 0x00 and the duration can be selected between 3 0x03 and 10 0x04 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x80 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Br CMD 0x82 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Value 0x02 0x82 0x01 0x03 Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x82 0x01 0x05 Variable Variable Variable Variable Variable 0x03 OSD Turn Off Time OSD Info Display Time 1Byte 1Byte Value Variable Variable Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Control Value The value for Turn OFF is 0 0x00 10 seconds is 1 0x01 20 seconds is 2 0x02 and 30 seconds is 3 0x03 The duration rages for OSD Info Display Time can be selected between 3 0x03 and 10 0x0A and OFF is 0 0x00 Check Sum Execute Not operation after adding all the values in STX Data area SETUP B Command 7 1 Power On Source his
9. You can see the screen more clearly When you choose a lighter around 3 EXIT MENU Press Exit button to exit from the menu o gt SCREEN RESET Adjustment Initialize the values of SCREEN MENU 1 Select SCREEN RESET from SCREEN menu Press MENU button to display OSD Use amp ft buttons to move to SCREEN RESET and press MENU button PICTURE H POSITION V POSITION it ASPECT RATIO VIDEO MUTE SETUPA SCREEN MODE SCREEN RESET SETUP B Vv You can see the screen more clearly When you choose a lighter around 2 Initialize the previously adjusted values Select YES or NO for initializing SCREEN menu Use amp ft buttons to move to YES and press MENU button to initialize the value z PICTURE H POSITION V POSITION ASPECT RATIO VIDEO MUTE SCREEN MODE SCREEN RESET SETUP B You can see the screen more clearly When you choose a lighter around 3 EXIT MENU Press Exit button to exit from the menu a E SETUP A Configuration gt AUTO POWER Configuration AUTO POWER DISPLAY MODEL FIRMWARE VERSION LAN SETTING SERIAL The display set can be turned on automatically as the power is on SETTING OSD and SETUP A RESET can be adjusted in SETUP A MENU ON Select the function for automatic turn on OFF Deselect the function 1 Select AUTO POWER from SETUP A menu Use amp ft buttons to select ON or OFF Move to ON and press
10. 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tripod bracket or table specified by the manufacturer or sold with the apparatus When a cart is used use e caution when moving the cart apparatus combination to avoid injury from tip over 13 Unplug this apparatus during lightning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped The symbol in figure 21 shall be shown adjacent to the text of item 12 above Content 01 4 Cautions for System UOT eire tele 4 BF E E E 5 CAUTION 6 gt Do not cover the vent hole for the 7 RISK
11. PICTURE AUTO POWER DISPLAY MODEL SCREEN FIRMWARE VERSION LAN HPOSITION r SETUP A ERAI VPOSITION INFO DISPLAY OFF OSD TRANSPARENCY OFF SETUP B SETUP A RESET Vv You can see the screen more clearly When you choose a lighter around 2 20 OSD POSITION Configuration e H POSITION Select the horizontal position of OSD e V POSITION Select the vertical position of OSD 1 Select OSD H POSITIION Use mbbuttons to adjust OSD H POSITION value PICTURE AUTO POWER DISPLAY MODEL SCREEN FIRMWARE VERSION TURN OFF OFF LAN HPOSITION E p SETUP A VPOSITION INFO DISPLAY OFF OSD TRANSPARENCY OFF BAUDRATE SETUP A RESET You can see the screen more clearly When you choose a lighter around 2 Select OSD V POSITIION Use buttons to adjust OSD V POSITION value PICTURE AUTO POWER DISPLAY MODEL SCREEN FIRMWARE VERSION TURN OFF OFF LAN HPOSITION VPOSITION ES INFO DISPLAY OSD TRANSPARENCY OFF BAUDRATE SETUP A RESET can see the screen more clearly When you choose a lighter around 3 EXIT MENU Press Exit button to exit from the menu c INFO DISPLAY Configuration INFO DISPLAY Select the duration time of INFO OSD 1 Select INFO DISPLAY Turn on or off INFO DISPLAY OSD and select display duration time Use amp ftbuttons to select ON or OFF Press MENU button
12. T 5 5 tISISISISIS S SmSISISIS vele z gjz g s zjz s s g js g s E EJS S S EIE S S ES O JO a ee aS en DEX EX EX EX G amp X EX E EX S Se EX 2 EX EX amp amp x Ex Cx D D D D D D D D D D D D D D D D D D D D D D D D Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Control If DHCP configuration is deselected it is 0 0x00 If it is selected it is 1 0x01 The length of IP Address Subnet Mask Default Gateway DNS Primary and DNS Secondary is 4Bytes respectively Check Sum Execute Not operation after adding all the values in STX Data area 6 7 Get MAC Address hisis the command for checking MAC Address CMD 0x76 2 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Value 0x02 0x76 0x01 0x03 Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x76 0x01 0x09 Variable Variable Variable Variable Variable 0x03 Mac Address Mac Address Mac Address Mac Address Mac Address Mac Address 1Byte 1Byte 1Byte
13. Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD STX CMD Ex CMD Length Data Group ID Multi ID Mode Control 23Bytes Check Sum ETX Value 0x02 OxB9 0x01 Variable Variable Variable Variable 0x03 Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode version 20Bytes Value 0x02 OxF9 0x01 0x17 Variable Variable Variable ceses Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Version e g 0 80 01A 020121116BT 20 Byte 0x30 Ox2E 0x38 0x30 Ox2E 0x30 0x31 0x41 Ox2E Ox4F 0 8 0 0 1 A O Year 2012 Nov 16th Revision Beta Test Release First A A A 0x02 0x00 0x01 0x02 0x01 0x01 0x01 0x06 0x52 Ox56 RV 0x42 0x54 BT 0x52 Ox46 RF Check Sum Execute Not operation after adding all the values in STX Data area 6 4 DHCP This is the command for selecting or deselecting automatic Network IP configuration CMD 0x73 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 0x73 0x01 0x04 Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write S
14. 16 383 W X 16 383 D Active Display Area H Xv 1860 48 X 1046 52mm Aspect Ratio 1659 Response Time oms to 25ms depending on conguration Typical response time 15ms Number of pixels 3840 H X 2160 V Glass Transmission Better than 8596 with glass Thickness omm Tempered Glass Option AG AR Pixel Pitch 0 4845 X 0 4845 mm Display Colors 1 06Billon Colors Optics Quantity 326 H X 183 V pairs Viewing Angle Response Time Gto G H 178 V 178 amsec Typ Touch Intensity Over 60 000 000 single point touch Environmental Temperature SC a0 6 condition Humidity 39 7596 Support OS Windows Vista Windows 7 Windows 8 32bit and 64bit Windows CE Linux Mac OS No device driver required HDMI VGA SVGA XGA SXGA UXGA WXGA True Multi Touch Detects up to 6 points HDCP Available 480p 576p 720p 50 60 1080i 50 60 1080p 50 60 Frequency 75kHz V2 00 60 Hz Input port HDMI x 8 RS 232C x 1 LAN x1 A S x 1 IR x 1 Input Signal Product design and specification can be changed for quality improvement without prior notice Lamp Life Time Typ 50 000Hrs Ta 25 2 C Dimension W XH XD 1917x 1103 x 95mm 1977 2 x 1163 2 x 1043mm 1917x 1103 x 95mm Weights 72Kg 0 5Kg 120Kg 0 5Kg 72Kg 3 0 5Kg Landscape Portrait Installation Landscape only X P
15. Execute Not operation after adding all the values in STX Data area 5 2 V Position hisis the command to control the vertical position of the image within the Display area of the LCD CMD 0x37 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 0x37 0x01 0x04 Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Control Value 0x00 0 0x64 100 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX Group ID Multi ID Mode Control Value 0x02 0x37 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Value Ox00 0 0x64 1 00 Check Sum Execute Not operation after adding all the values in STX Data area 5 3 Aspect Ratio Aspect ratio can be selected or changed to 16 9 or 4 3 CMD 0xB6 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 OxB 0x01 0x04 Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Control Value 0x01 1 for 1
16. Ox15 HDMI2A 0x16 HDMI2B 0x17 HDMI2C 0x18 HDMI2D 0x31 UHD 1 0x32 UHD 2 his is the command for controlling the brightness of LCD back light Check Sum Execute Not operation after adding all the values in STX Data area Itis available only during Power On Operative status CMD 0x1D 7 2 Get Power On Source Data Send To LCD This is the command for checking the configuration of the input source that should be detected with the first priority at the time of Power On Data tis available only during Power On Operative status STX CMD Ex CMD Length ETX CMD 0x56 Group ID Multi ID Mode Control Send To LCD Value 0x02 Ox1D 0x01 0x04 Variable Variable Variable Variable 0x03 STX CMD Ex CMD L h iis ETX X engt Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Sree pNP mee Biggs Mode Read Get 0x00 0 Write Set 0x02 2 Value 0x02 0x66 0x01 0x03 Variable Variable Variable 0x03 Control Value The range of Control value is from 0x00 0 OxFF 255 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Receive From LCD Mode Read Get 0x00 0 Data Receive From LCD STX CMD Ex CMD Length Check Sum ETX Group Multi ID Mode Control Data STX CMD Ex CMD Length Check Sum ETX Value 0x02 0x1D 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID Mode Control Value 0x02 0x66 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group Mu
17. 1Byte 1Byte 1Byte Value Variable Variable Variable Variable Variable Variable Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Control Value The range of each value is from 0 0x00 to 255 xFF Check Sum Execute Not operation after adding all the values in STX Data area 6 8 Baud Rate his is the command for configuring the Baud Rate for LCD communication It is available only during Power On Operative status CMD lt 0x78 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 0x78 0x01 0x04 Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set 0x02 2 Control 9600 1 0x01 14400 2 0x02 19200 3 0x03 38400 4 0x04 57500 5 0x05 115200 6 0x06 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x78 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set Response 0x02 2 Control 2600 1 0x01 14400 2 0x02 19200 3 0x03 38400 4 0x04 57500 5 0x05 115200 6 0x06 Check Sum Execute Not operation after adding all the values in STX Data area 6 9 Get Baud Rate Data This is the command for checking the configuration of the Baud Rate for LCD communicatio
18. 3 4 Information a SENG TOLED Data tis the command for displaying the information of LCD set status STX CMD Ex CMD Length ETX It is available only during Power On Operative status Group ID Multi ID Mode Control CMD 0x1A Value 0x02 0x21 0x01 0x04 Variable Variable Variable Variable 0x03 Send To LCD w Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed ara Mode Read Get 0x00 0 Write Set 0x02 2 STX CMD Ex CMD Length ETX 3 Group ID Multi ID Mode Control 0x00 0 0x64 100 Value 0x02 0x01 0x03 Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set 0x02 2562 250 Receive From LCD Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed 68 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 E m D Control 0x00 0 0x64 10
19. CMD Length ETX Value 0x02 Variable 0x01 0x04 Variable Variable Variable Variable 0x03 Group ID Multi ID Mode Control Value 0x02 OxBO 0x01 0x04 Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set 0x02 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Control The controllable range of Gain RGB and Offset RGB is from 0 0x00 to 200 0xC8 respectively Mode Read Get 0x00 0 Write Set 0x02 2 Control Panel Key Lock Off 0x00 0 Panel Key Lock On 0x01 1 s Receive From LCD Receive From LCD Data Data STX CMD Ex CMD Length Check Sum ETX STX CMD Ex CMD Length Check Sum ETX Group ID Multi ID Mode Control Group ID Multi ID Mode Control Value 0x02 Variable 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Value 0x02 0xB0 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Panel Key Lock Off 0x00 0 Panel Key Lock On 0x01 1 Check Sum Execute Not operation after adding all the values in STX Data area 270 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set Response 0x02 2 Control The controllable range of Gain RGB and Offset RGB is from 0 0x00 to 200 0xC8 respe
20. Do you want to keep these changes Reverting in 15 seconds e Click the display No 4 in the Display selection part with the right button of your mouse to popup the window and select Duplicate RADEON GRAPHICS Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware To configure a desktop click the triangle W on the desktop below Click and drag desktops to Desktop arrange them Management Common Display Tasks AMD Eyefinity Multi Display My Digital Flat Panels Disable Identify Display Duplicate 51 Since the display No 1 is left to duplicate the window for selecting the display for duplication will not be popped up and the following caution window will be displayed Then select Continue he screen will be turned off for a moment and turned on After the screen is turned on the following caution window will be displayed Then select Yes Your displays have been reconfigured Do you want to keep these changes Reverting in 15 seconds 5 All the displays are duplicated as the display No 1 RADEON AMD Tasks AMD Eyetinity Muliti Display My Digital Flat Panels Information Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate d
21. Each value can be adjusted by 4 mb buttons BRIGHTNESS CONTRAST POLYCOM SCREEN TINT COOL USER RO OC USER G O COLOR SETUP A VIDEO MODE USER B O USER R USERG USERB PICTURE RESET SETUP B Vv ose 8 lighter around gt PICTURE RESET Initialize the values of PICTURE NENU 1 Select PICTURE RESET from PICTURE menu Press MENU button to display OSD Use amp ft buttons to move to PICTURE RESET and press MENU button SCREEN SETUP A SETUP B BRIGHTNESS CONTRAST TINT COLOR VIDEO MODE PICTURE RESET 2 Initialize the values Select YES or NO for initializing PICTURE RESET menu Use amp f buttons to move to YES and press MENU button to initialize the value marem SCREEN SETUP A SETUP B 3 EXIT MENU BRIGHTNESS CONTRAST TINT COLOR VIDEO MODE PICTURE RESET Press Exit button to exit from the menu after reset ES E SCREEN ADJUSTMENT Group 1 Group 2 COD um ecco e H POSITION V POSITION ASPECT RATIO VIDEO MUTE SCREEN MODE and SCREEN RESET can be adjusted in the SCREEN MENU 1 Press MENU button Press MENU button to display OSD MENU on the screen PICTURE H POSITION V POSITION ASPECT RATIO VIDEO MUTE SETUPA SCREEN MODE SCREEN RESET SETUP B Vv ore clearly 2 Select SCREEN menu Use amp f buttons to move SCREEN menu
22. Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware To confiqure a desktop click the triangle W on the desktop below Click and drag desktops to arrange them Desktop N Advanced Display settings Desktop Color Common Display Tasks wv AMD Eyefinity Multi Display My Digital Flat Panels Please select a display Disable Identify Display om gt Information Display selection part 46 cue When you see the massage Please select a desktop to duplicate on the screen as shown below select the display No 1 in the Desktop layout part RADEON Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware Please select a desktop to duplicate ew m 9 d Management Creating and Arranging Desktops Desktop Properties Advanced Display Settings Desktop Color l Common Display Sis ax AMD Eyetinity Mutti Display My Digital Flat 2 Panels m o 208 Then you will see the following window for caution Select Continue s he screen will be turned off for a moment and turned on After the screen is turned on the following caution window will be displayed Then select Yes Catalyst Control Cente
23. Length 0x03 Group ID Variable Multi ID Variable Mode Variable ETX 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 2 72 CMD 0x74 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 0x74 0x01 0x17 Variable Variable Variable Variable 0x03 IP Address Subnet Mask Default Gateway DNS Primary DNS Secondary 4Byte 4Byte 4Byte 4Byte 4Byte S 5 5 5 S m SIS SISIS SIS vue s s8 s s s8 8 s S E S S S S S S S O O mE EX ODE DOER DOORS 0 SES S X qp pp Xm mx mx D XS D EE D OE D D D D D D D D D D D D D D D D D D D D ZOO OXF Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX Group ID Multi ID Mode Control Value 0x02 0x74 0x01 0x17 Variable Variable Variable Variable Variable 0x03 IP Address Subnet Mask Default Gateway DNS Primary DNS Secondary 4Byte 4Byte 4Byte 4Byte 4Byte ee he e We oe eee eae Me e oe Wee ei ee me he vele z z sz g s x z s s slslsl ls EQE S EQE S O qme OJOJOO EE xD e DERE EOS EE S S Se SS D D D D D D D D D D D D D D D D D D D D Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set 0x02 2 Control Value The range
24. MENU button to select and move to OFF and press MENU r3 button to deselect PICTURE AUTO POWER 1 Press MENU button Press MENU button to display OSD MENU on the screen PICTURE AUTO POWER DISPLAY MODEL SCREEN FIRMWARE VERSION DISPLAY MODEL LAN SCREEN FIRMWARE VERSION da SETUP A ECT LAN OSD SETUP A SETUP B BAUDRATE SETUP A RESET OSD Group1 Group2 CD uu 07 umb screen more clearly When you choose a SETUP B SETUP A RESET Vv ore clearly When you choose a lighter around DD SSD 2 selectsETUP A a e C Use amp 3 buttons to move to SETUP A menu 2 EXIT MENU Press MENU button to move into the sub menu AUTO POWER LAN SETTING SERIAL SETTING and OSD menu can be adjusted DISAPLAY MODEL and FIRMWARE VERSION also can be checked Press Exit button to exit from the menu DISPLAY MODEL Configuration e It displays the model information 3 Each sub menu can be configured Use amp f buttons to move to the sub menus you want to adjust To configure the sub menu move to the sub menu and press MENU button to 1 Select DISPLAY MODEL from SETUP A menu enter Move to DISPLAY MODEL and press MENU button to check current model name 4 EXIT MENU PICTURE AUTO POWER Press Exit button to exit from the menu DISPLAY MODEL SCREEN FIRMWARE VERSION LAN OSD SETUP B SETUP A RESET Vv e screen more clearly When you choo
25. No user serviceable part inside Refer servicing to qualified service personnel 2 Supplied Accessories Y User s Manual HDIM Cable 4EA Power Cable RS 232C Cable Remote Control Battery IR Receiver AAA X2 Ultra High Definition LCD A FA D in b d Cable tie Cable tie base Monitor clip Form strip Class A digital device Notice to users It is a device designed for business purpose with a safety certificate for electromagnetic interference which user should be mindful of Important Safety Instructions Head these instructions NO _ M00 SA M00 M00 MM T Keep these instructions Go Heed all warnings 4 Follow all instructions O1 Do not use this apparatus near water 6 gt Clean only with dry cloth Do not block any ventilation openings Install in accordance with the manufacturer s instructions CO Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9 Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A grounding type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet
26. OF ELECTRIC SHOCK LSPS AVG MaintenarniCE E i DO NOT OPEN O NOT O 02 Safety Precautions ttt ttti 8 03 10 CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK aah eer een c er 10 DO NOT REMOVE COVER OR BACK ROI 10 NO USER SERVICEABLE PARTS INSIDE P Input Ports 11 REFER SERVICING TO QUALIFIED SERVICE PERSONNEL a1 0 i p nonus RN CHE DU RC RM E ICM EU DE oU DDR lo This symbol is intended to alert the user to the presence of uninsulated dangerous 04 Cable 14 voltage within the product s enclosure that may be of sufficient magnitude to E bet dec fe chock 05 How to use Remote Controller 16 06 Configuration 18 isse eil OPUS TIVIEI NT EE 17 This symbol is intended to alert the user to the presence of important operating and e ca Plc eeen R 19 maintenance servicing instructions in the literature accompanying the appliance gt TINT ADJUSTMENT m CTR ADIUS TAMEN T Me 20 PIDE dE SEPSC TEM oes tette aaa Ee re SOT rene PEND a Ud 2 22 m 24 RU 2
27. Refresh Paste Faste shortcut New k Screen resolution Gadgets Personalize 45 1 Duplicating Display e Click the display No 2 in the Display selection part with the right button of your mouse to popup the window and select Duplicate e Select Creating and Arranging Desktops from the menu bar on the left after executing CCC The upper part of the Creating and Arranging Desktops window is Desktop layout part and the lower part is Display selection Part The basic display No 1 2 3 and 4 will be displayed as shown below RADEON But the layout may vary due to the cable connection Catalyst Control Center AMD Preferences Creati d Arranging Desktops Following process is duplicating the display No 2 3 and 4 as the display No 1 In case you do not have the same display layout like following AIL KAUF LEM SL eA screen image you still duplicate the displays as described below Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware To configure a desktop click the triangle W on the desktop below Click and drag desktops to arrange them Management Creating and Arranging Desktops Desktop Properties Advanced Display settings Desktop Color Common Display Tasks v Multi Display My Digital Flat Panels RADEON Catalyst Control Center AMD Preferences Creating and Arranging Desktops w 7
28. USB For touch sensor Only Touch Model 7 A S Service port for firmware upgrade 4 HDMI Group 1 1A 18 1C 1D 8 IR Group 2 2A 2B 2C 2D Remote controller input port 10 Ai KEY PAD Gp 0000000 C srcmope gt lt ENT RR 0 0909 O 1 PWR Power 5 ENT Enter Turn on or off the display 2 SRC Input source selection Select HDMI input 3 MODE MENU Turn on or off the menu or select adjust menu 4 Direction up down left and right Move up down left or right direction on the menu screen Select adjustment 6 IR IR Reception Receive the IR signal from remote controller 7 Power Indication Lamp Indicate the power status Remote Controller POWER ON POWER OFF Turn on the display Turn off the display EXIT INFO Exit from MENU amp Configuration Display the resolution ent yt MENU Movement MENU Display OSD MENU on the screen amp ENTER UHD UHD Select HDMI 2 CHANNEL for UHD SCREEN MODE Select HDMI 1 CHANNEL for UHD SCREEN MODE HDMI 1A HDMI 2A Select HDMI 1A for Input source Select HDMI 2A for Input source HDMI 1B HDMI 2B Select HDMI 1B for Input source Select HDMI 2B for Input source HDMI 1C HDMI 2C Select HDMI 1C for Input source Select HDMI 2C for Input source HDMI 1D HDMI 2D Select HDMI 1D for Input source Select HDMI 2D for Input source mien IR Reception
29. be adjusted Each ofthe value can be adjusted by pressing 4 buttons 4 Exitfrom the MENU Press EXIT button to getting out of OSD MENU 18 When PICTURE item is selected press MENU button to move into the sub menu BRIGHTNESS ADJUSTMENT e Screen brightness can be adjusted The brightness of black color at the dark side of the screen can be adjusted 1 Select BRIGHTNESS from PICTURE Menu Select BRIGHTNESS and move mb buttons to adjust the value PICTURE BRIGHTNESS init CONTRAST SCREEN TINT COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B 2 EXITMENU Press Exit button to exit from the menu after adjusting the value CONTRAST ADJUSTMENT The brightness of white color at the bright side of the screen can be adjusted 1 Select CONTRAST from PICTURE menu Select CONTRAST and move mb buttons to adjust the value le gt PICTURE BRIGHTNESS CONTRAST SCREEN TINT COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B 2 EXIT MENU Press Exit button to exit from the menu after adjusting the value o gt TINT ADJUSTMENT e Adjust Red and Green color of the screen 1 Select TINT from PICTURE Menu Select TINT and move buttons to adjust the value 2 PICTURE BRIGHTNESS ut CONTRAST SCREEN TINT COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B 2 EXITMENU Press Exit button to exi
30. dust oil smoke or steam It may cause failure f you do not want to use the product Do not put any heavy object on it for a long time keep the power plug It may cause failure unplugged to save electricity near the equipment and be easily accessible Install the product on safe and flat surface Do not put candles on the product If the liquid flows inside the product It may cause electric shock or fire Do not ride or step on the product It may When moving it disconnect the connecting cable Otherwise it may damage the cable to cause fire or electric shock cause breakage when fallen down Do not touch product s front surface with Do not poke the front screen with sharp hand Otherwise the image quality can material It may damage the screen and be lowered may cause malfunction of the product 03 Names Front gt Input Ports 8 E gt S S S O E gt A S IR LAN o9 9 RS232 e HDMI2B HDMI2C HDMIID 2 USB HDMI1B HDMI1C ACINPUT ON OFF HDMI1A 0 1 AC Input 5 RS 232C AC 100V 240V 50 60Hz Display control via COM port or firmware upgrade D Sub 9pin 2 ON OFF Switch Turn on or off the display 6 LAN Display control via Ethernet RJA5 3
31. exit from the menu 38 250 gt SETUP B RESET Configuration Initialize the previously adjusted values of SCREEN B MENU gt FACTORY RESET Configuration Initialize the previously adjusted values of the set to the factory level Every configuration will be initialized 1 Select SETUP B RESET from SETUP B menu Press MENU button to display OSD 1 Select FACTORY RESET from SETUP B menu Use amp f buttons to move to SETUP B RESET and press MENU button Press MENU button to display OSD Use f buttons to move to FACTORY RESET and press MENU button PICTURE POWER ON SOURCE KEY LOCK PICTURE POWER ON SOURCE SCREEN SETUP B RESET KEY LOCK FACTORY RESET SCREEN SETUP B RESET SETUP A FACTORY RESET SETUP A p gt SETUP B SETUP B 2 Initialize the previously adjusted values Select YES or NO for initializing SETUP B menu 2 Initialize the previously adjusted values Use amp f buttons to move to YES and press MENU button to initialize the value PICTURE SCREEN SETUP A and SETUP B menus can be initialized to the factory level jr Select YES or NO for initialization hohe Use amp ft buttons to move to YES and press MENU button to initialize the value KEY LOCK SCREEN SETUP B RESET a FACTORY RESET PICTURE POWER ON SOURCE SETUP A KEY LOCK SCREEN SETUP B RESET F SETUP B FACTORY RESET SETUP A 3 EXITMENU Press Exit button to exit from the menu 3 EXITMENU abs
32. image on the screen 1 Select V POSITION from SCREEN menu Adjust V POSITION values with buttons after selecting V POSITION PICTURE H POSITION V POSITION ASPECT RATIO PICTURE SETUP A SETUP B You can see the screen more clearly When you choose a lighter around 2 EXIT MENU Press Exit button to exit from the menu H POSITION V POSITION ASPECT RATIO VIDEO MUTE SCREEN MODE SCREEN RESET DE 3 VIDEO MUTE SETUPA SCREEN MODE SCREEN RESET SETUP B Vv You can see the screen more clearly When you choose a lighter around EXIT MENU Press Exit button to exit from the menu ae gt VIDEO MUTE e Display the input image on the screen e ON Display on the screen e OFF No screen display Black screen 1 Select VIDEO MUTE from SCREEN menu Configure VIDEO MUTE value by pressing MENU button after selecting VIDEO MUTE PICTURE H POSITION V POSITION ASPECT RATIO VIDEO MUTE SETUPA SCREEN MODE SCREEN RESET SETUP B You can see the screen more clearly When you choose a lighter around 2 Select VIDEO MUTE value Use amp f buttons to move to ON or OFF To select VIDEO MUTE move to ON and press MENU button Move to OFF and press MENU button to deselect VIDEO MUTE PICTURE H POSITION V POSITION Lam SCREEN ASPECT RATIO VIDEO MUTE SETUP A SCREEN MODE SCREEN RESET SETUP B Vv
33. is the command for selecting and configuring the input source that should be detected with the first priority at the time of Power On Itis available only during Power On Operative status CMD 0x63 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 0x63 0x01 0x04 Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set 0x02 2 Control Input Source configuration 0x10 is for the last input source at the time of the last Power Off 0x1 1 HDMI1A 0x12 HDMI 1B 0x13 HDMI1C 14 HDMIT1 D 0x15 HDMI2A 0x16 HDMI2B 0x17 HDMI2C 0x18 HDMI2D 0x31 UHD 1 Ox32 UHD 2 Receive From LCD STX CMD Ex CMD Length Data Group ID Multi ID Mode Control Check Sum ETX Value 0x02 0x63 0x01 0x04 Variable Variable Variable Variable Variable 0x03 J Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed 8 Factory Control Command Mode Write Set Response 0x02 2 Control Input Source configuration 0x10 is for the last input source at the time of the last Power Off 0x11 HDMI1A 0x12 HDMI1B 0x13 HDMI1C 14 HDMI1D 8 1 Dimming Control
34. 0 STX CMD Ex CMD Length ate Check Sum Execute Not operation after adding all the values in STX Data area GroupID Multi ID Mode Control Value 0x02 0x21 0x01 0x04 Variable Variable Variable Variable Variable 0x03 4 9 Video Mode Color Temperature Mode ID Multi ID P 5G ID 0x01 Multi ID 0x01 Fixed This is command to adjust the color temperature of the entire screen A WARM 6500K will make the screen reddish roup ulti ID range Program Group ID 0x ulti ID 0x01 Fixe l Mode Read Get Response 0x00 0 Write Set Response 0x02 2 A COOL 1000K will make the screen bluish A Natural is the color temperature of the typical panel without any adjustmen A Polycom is the Control 0x00 0 0x64 100 requested color temperature of buyer If COLOR TEMPERATURE needs further adjustment CUSTOM must be showing as the Video Mode Check Sum Execute Not operation after adding all the values in STX Data area selection Color temperature is 8000K for Polycom mode 10000K for Cool mode and 6500K for Warm mode Natural Mode is the color temperature of the 4 3 Color Control typical panel without any adjustment User can control the color temperature with Custom mode Itis available only on Power On Operative status This is the command to adjust the color depth of the screen The adjusted value cannot be applied for Stand By or No input status So it can be applied when LCD is in operating condition with t
35. 4 NOTIC E tht Impp 23 bru 26 1 To disconnect the apparatus from the mains the plug must be pulled out from the mains socket gt SCREEN RESET 74 therefore the mains plug shall be readily operable gt AUTO POWER Configuration cccecssssssssssssssssssssssssssssssssssssssseccscseessssecseccssssssssssessssssessssssssssssssssssssssisssssssssssssssveeeeeeeeeeeeen 25 gt DISPLAY MODEL COnfigurationnuccccccccssssssssssssssssssssssssssssscescescecssesesseccesssssssssessssssessssssssssssssssssssssissssssssssssssssssveeeeeeeeeeeee 29 2 WARNING To Reduce The Hisk Of Fire Or Electric Shock Do Not Expose This Appliance To FIRMWARE Configuration 30 Rain Or Moisture 30 3 Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids such BAUD RATE Configuration A as vases shall be placed on the apparatus 32 SETUP ARE i ddp EEA RETN 36 4 Use only a properly grounded plug and receptacle P POWERON SOURCE 38 Warning CAUTION These servicing instructions are for use by qualified service personnel only B KEY LOCK Configuration 39 To reduce the risk of electric shock do not perform any servicing other than that contained in the gt SETUP B RESET Configurati
36. 6 9 0x02 2 for 4 3 Receive From LCD Data STX CMD Ex CMD Length N Check Sum ETX GroupID Multi ID Mode Control Value 0x02 OxB 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Value 0x01 1 for 16 9 0x02 2 for 4 3 Check Sum Execute Not operation after adding all the values in STX Data area 5 4 Video Mute tisthe command for selecting Video Mute User can select blank screen CMD 0xB7 70 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 OxB7 0x01 0x04 Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Control Blank 0x00 0 Unblank 0x01 1 Receive From LCD Data STX CMD Ex CMD Length AN Check Sum ETX GroupID Multi ID Mode Control Value 0x02 OxB7 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Blank 0x00 0 Unblank 0x01 1 Check Sum Execute Not opera
37. IPIM PPY 5104 1401 YIPIM UAS Yyd10d 1268 Polarity H V Standard Type 640 480 60 20 175 NO DMT 800 600 50 30 750 CVT 800 600 60 40 000 DMT 1024 576 50 34 750 VESA Blanked 1024 576 60 46 500 VESA 1024 768 60 65 000 DMT 1280 768 60 79 500 CVT 1280 960 60 1280 1024 50 108 000 88 500 CVT 1280 1024 60 108 000 1360 768 50 69 000 1360 768 60 85 500 1400 1050 60 121 790 1600 900 50 96 500 1600 900 60 118 250 1600 1200 50 131 000 1600 1200 60 162 000 480p 27 000 576p 720p50 27 000 720p60 1080150 1080i60 1080p50 148 500 1080p60 148 500 11 Specification gt Product Model Name OLS 8410NL OLS 8410T6LG OLS 8420NL Touch Item Description Back Light Type LED Power Supply AC100V 240V 50 60H2z Touch Technology PulselRTM Technology Power Max 470W Touch Method Finger gloved hand or Any other pointer Stylus minimum 8mm Consumption Typical 440W Stand By 0 45W Touch Activation Force No pressure required Luminance of White 350 ca 7 m Max 5000 cd m Max Position Accuracy Typical centroid accuracy 2mm Contrast ratio Dark Room 1 600 1 Typical Resolution
38. ORION CO LTD www oriondisplay net Address 257 6 Gongdan dong Gumi si Gyeongsangbuk do Korea Tel 82 2 6678 8533 Fax 82 2 6678 8599 2013 05 31 tra High Definition LED User s Manual Thank you for purchasing this product Please read this manual thoroughly prior to install the product for your safety 4 E Features gt Enjoy a wide flat screen with high brightness and high quality gt Easy to install and move due to its thin design gt Enjoy your favorite programs with various split screen features simultaneously presenting several programs EEE UGB L UGGLH IAG OLL AIL LAALILLLLDLL GEelLALUHL 4 80LLCL O LS 4 Thank you for purchasing this product This manual describes how to use the product and notes in use Please read the manual carefully before using it After reading this manual please retain for future reference If you have any questions or a problem occurs please contact either the company you purchased this product from or an authorized service center X Displaying static picture for an extended period of time may cause an burn in effect X Burn in effect and the faults in brightness and picture elements caused by fixed images are not subject to the warranty coverage 9 If you fail to comply with the regulations for safety and proper use fire or N Warning injury may be caused To prevent electric shock Do not remove cover A Warn ng
39. Turn Off This is the command for configuring the duration time for OSD Menu It is available only during Power On Operative status CMD 0x7D Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 Ox7D 0x01 0x04 Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set 0x02 2 Control The value for Turn OFF is 0 0x00 10 seconds is 1 0x01 20 seconds is 2 0x02 and 30 seconds is 3 0x03 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x7D 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set Response 0x02 2 Control The value for Turn OFF is 0 0x00 10 seconds is 1 0x01 20 seconds is 2 0x02 and 30 seconds is 3 0x03 Check Sum Execute Not operation after adding all the values in STX Data area 6 11 OSD Info Display Time This is the command for selecting Info OSD display on the screen and configuring the duration Itis available only during Power On Operative status CMD 0x80 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control
40. Z lt X Note Moving picture or black pattern is strongly recommended for screen saver 2 Operating methods to minimize burn in image due to long term static information display Suitable operating time under 12 hours a day Periodical display contents change from static image to moving picture Periodical background color and character image color change DEPARTURE DEPARTURE Time Gate 2 KE732 1210 Leen 8 Flight No ate Change the images of little luminance difference between the background and characters periodically DEPARTURE gt 1120 02 5 not recommended to display the images of huge luminance difference between the background and characters or the images of grey tone A x Scroll the characters periodically DEPARTURE nEDADTIIDE DEPARTURE Whole Screen Scroll zs lt G Clearance for Ventilation When you install product make sure there is at least 20cm clearance for effective ventilation and do not seal off MLCD sets If MLCD sets are installed at the locations of bad ventilation the inner temperature can be raised rapidly and it can cause frequent malfunctions and rapid reduction of the product life X Ventilation space in front of product must be furnished for heat dispersion If the front space of MLCD has to
41. after selecting ON or OFF PICTURE SCREEN f SETUP A SETUP B AUTO POWER DISPLAY MODEL FIRMWARE VERSION TURN OFF OFF LAN HPOSITION BAUDRATE VPOSITION amp OSD TRANSPARENCY OFF SETUP A RESET Vv u can see the screen more clearly When you choose a lighter around 2 EXIT MENU Press Exit button to exit from the menu TRANSPARENCY Configuration e TRANSPARENCY Select the transparent percentage of OSD 1 Select TRANSPARENCY The transparency of OSD can be adjusted Use amp ft buttons to select ON or OFF Press MENU button after selecting ON or OFF PICTURE SCREEN rf SETUP A SETUP B AUTO POWER DISPLAY MODEL FIRMWARE VERSION TURN OFF LAN HPOSITION VPOSITION INFO DISPLAY BAUDRATE OSD SETUP A RESET Vv 21 can see the screen more clearly When you choose a lighter around Move Enter 2 EXITMENU Press Exit button to exit from the menu 35 gt SETUP A RESET Configuration Initialize the previously adjusted values of SETUP A RESET MENU 1 2 3 Select SETUP A RESET from SETUP A menu Press MENU button to display OSD Use amp ft buttons to move to SETUP A RESET and press MENU button PICTURE AUTO POWER DISPLAY MODEL SCREEN FIRMWARE VERSION LAN MORSU A BAUDRATE OSD SETUP B SETUP A RESET Vv e screen more clearly When you choose a Initialize the previously adjuste
42. be sealed there must be consideration for the heat dispersion in the rear side of MLCD Do not cover the vent hole for the fan Carefully install product not to cover the fan air holes with any structural object If the holes are covered with anything the inner temperature can be raised rapidly and it can cause malfunctions Installation structure FAN DEAE ETE FED TEE TE TLTETE TTE I De CHE A ET RS CL ae eg a VI OE De TE ITA ae zZ Z lt Ae De ee hd Se DITE DD TO eT eh ITE Dee en TTS TT LEE TERRE PD eo Teg TEE TER AR TEO T TREE CETERIS TET UD ACTOS Te TE TE Cleaning and Maintenance Regularly clean off the vent holes in the back of product sets If the vent holes and the fan air holes are clogged with dust it prevents the air flow inside of product sets It can cause rapid increase of the inner temperature and may cause malfunctions Clean off the vent holes and the fan air holes with a vacuum cleaner regularly Vacuum Cleaner 02 Safety Precautions f it operates abnormally stop using it immediately tt t Please refer to a specialized construction company for installing stand or wall mount unit Otherwise damage injury may be caused Do not place any liquid containing Do not put any foreign mat
43. clearly When you choose a lighter around Menu Move Enter 2 Press MENU button to move into the sub menu of BAUD RATE Use amp ft buttons to adjust values Press MENU button to select a value PICTURE SCREEN p r SETUP A SETUP B AUTO POWER DISPLAY MODEL FIRMWARE VERSION 9600 LAN 19200 38400 57600 OSD 115200 BAUDRATE SETUP A RESET Vv screen more clearly When you choose a lighter around 3 EXIT MENU Press Exit button to exit from the menu o gt OSD Configuration 2 Select the sub items of TURN OFF It configures OSD menu Select the duration time for OSD CONTRON MENU or TURN OFF 1 Select OSD from SETUP A menu A PICTURE AUTO POWER Move to OSD and press MENU button DISPLAY MODEL SCREEN FIRMWARE VERSION PICTURE AUTO POWER 10 SEC LAN HPOSITION 3 20 SEC ety 30 SEC p at SETUP A SE V POSITION INFO DISPLAY 050 TRANSPARENCY DISPLAY MODEL SCREEN FIRMWARE VERSION LAN SETUP B SETUP A RESET Vv amp s SETUP A BAUDRATE You can see the screen more clearly When you choose a lighter around Move Enter OSD STE SETUP A RESET Vv 3 EXIT MENU Press Exit button to exit from the menu You can see the screen more clearly When you choose a lighter around TURN OFF Configuration TURN OFF Select the duration time of OSD on the screen 1 Select TURN OFF Move to TURN OFF and press MENU button
44. ctively Check Sum Execute Not operation after adding all the values in STX Data area 79 09 Before calling for service Before calling for any repair check the following and then refer to a near A S center gt Tick sound from the main body e f there is no problem with the screen or sound the tick sound is likely to result from the cabinet lightly shrinking with the change of room temperature The sound does not affect product s performance gt No image at upper and lower part of the screen for a screen which is over 16 9 in width such as cinema sized one no image may be displayed at upper and bottom part of the screen gt Speckles or white lines on the screen e Check whether the problem is caused by vehicle streetcar high voltage cable or neon sign which emitting interference wave or electromagnetic induction Avoid any interfering object gt Light leakage can be found at the edge areas around the screen e If the light leakage is not detected at 1m from the screen the panel is considered as no defect SAMSUNG LCD applies the same inspection standard minimize the light leakage the MLCD sets should be installed with high accuracy in horizontal and vertical position ES Resolution Horizontal Pixels 10 Applicable signals Vertical Lines YIPIM APPY Y10d 1401 1 5104 1209 Y
45. d values Select YES or NO for initializing SETUP A menu Use f buttons to move to YES and press MENU button to initialize the value PICTURE AUTO POWER DISPLAY MODEL SCREEN FIRMWARE VERSION LAN pa SETUP A BAUDRATE OSD ai is SETUP A RESET screen more clearly When you choose a lighter around EXIT MENU Press Exit button to exit from the menu 36 E SETUP B Adjustment e INFORMATION POWER ON SOURCE SETUP B RESET and FACTORY RESET can be Group 1 Group 2 D um um A C A 6 D B D adjusted in SETUP B MENU 1 Press MENU button Press MENU button to display OSD MENU on the screen PICTURE POWER ON SOURCE KEY LOCK SCREEN SETUP B RESET FACTORY RESET SETUP A Select SETUP B menu Use amp ft buttons to move to SETUP B Press MENU button to move into the sub menu POWER ON SOURCE SET UP B RESET and FACTORY RESET can be adjusted Current display configuration can be displayed by INFORMATION function Sub menus can be configured Use amp f buttons to move to the menus you want to adjust To configure the sub menu move to the sub menu and press MENU button to enter EXIT MENU Press Exit button to exit from the menu Eey gt POWER ON SOURCE Configuration KEY LOCK Configuration Select the default input source for power on Default HDMI 1A It restricts key strokes to prevent any of exp
46. ea 4 4 Tint Control 9 Screen Adjustment Command hisis the command to adjust the tint of the screen Itis available only on Power On Operative status 9 1 H Position The adi lied f Jte Soi e eet value cannot be applied for Stand By or No input status So it can be applied when LCD is in operating condition with the input s Thisiethe command te contral the horizontal mos mo f the agente Disbllavares Sethe ED Nov CMD 0x36 Send To LCD Send To LCD Data Data STX CMD Ex CMD Length ETX STX CMD Ex CMD Length A ETX Group ID Multi ID Mode Control Group ID Multi ID Mode Control Val 0x02 0x36 0x01 0x04 Variabl Variabl Variabl Variabl 0x03 Value 0x02 0x24 0x01 0x04 Variable Variable Variable Variable 0x03 i i i aa eats oe i T Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed ID aes Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 ode Read Get Ox00 0 Write Set 0x02 2 Control Value 0x00 0 0x64 100 Control 0x00 0 0x64 100 Receive From LCD Receive From LCD Data Data STX CMD Ex CMD Length Check Sum ETX STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control GroupID Multi ID Mode Control Val 0x02 0x36 0x01 0x04 Variabl Variabl Variabl Variabl Variabl 0x03 Value 0x02 0x24 0x01 0x04 Variable Variable Variable Variable Variable 0x03 a P i cua m a mE Bm Control Value 0x00 0 0x64 1 00 Check Sum
47. ected set activities OFF Display the input source right before power off ON Key buttons will not work OFF Key butt ill k 1 Select POWER ON SOURCE from SETUP B menu dba Use V 4 buttons to move to POWER ON SOURCE 1 Select KEY LOCK from SETUP B menu Use amp ft buttons to move to KEY LOCK and press MENU button PICTURE POWER ON SOURCE KEY LOCK PICTURE POWER ON SOURCE KEY LOCK SCREEN SETUP B RESET SCREEN SETUP B RESET FACTORY RESET SETUPA FACTORY RESET SETUP A F SETUP B F SETUP B Vv can see the screen more clearly When you choose a lighter around v 2 Press MENU button to move into the sub menu 2 Adjust KEY LOCK Select the input source mode to detect at the time of power on Use amp f buttons to move to ON or OFF Use amp f buttons to move to the item you want to select and press MENU Move to ON and press MENU button to activate KEY LOCK button o deactivate KEY LOCK move to OFF and press MENU button OFF PICTURE POWER ON SOURCE PICTURE POWER ON SOURCE KEY LOCK HDMI 1B KEY LOCK HDMI 1C SCREEN SETUP B RESET HDMI 1D HDMI 2A SCREEN SETUP B RESET FACTORY RESET FACTORY RESET HDMI 2B HDMI 2D SETUP A UD 1 F SETUP B 02 mi Vv Ww u can see the screen more clearly When you choose a lighter around 3 EXIT MENU 3 EXIT MENU Press Exit button to exit from the menu Press Exit button to
48. ee the screen more clearly When you choose a lighter around Move Enter 2 2 Direction buttons for movement amp f Use mb buttons or MENU button to adjust menu items Use amp f buttons to move to adjust sub menu items 3 EXIT button Press EXIT button to exit from the MENU after adjustment 4 INFO button The display information for the screen at the moment is displayed at the upper left corner of the screen ex Input HDMI 1A Ex UHD HDMI 1A HDMI 1B 640 X 480 640 X 480 HDMI 1A 60 HZ 60 HZ 640 X 480 HDMI 16 HDMI 1D 60 HZ 640 X 480 640 X 480 POLYCOM 60 HZ 60 HZ FULL VIDEO MODE POLYCOM E 5 UHD button Input A Input B Input C and Input D will be displayed on the screen simultanesously 6 A B C D button Selected input will be displayed on the whole screen e 06 Configuration m PICTURE Adjustment e BRIGHTNESS CONTRAST TINT COROR VIDEO MODE and PICTURE RESET can be adjusted in the PICTURE MENU 1 Press MENU button Press MENU button to display OSD MENU on the screen PICTURE BRIGHTNESS Summi CONTRAST SCREEN TINT COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B Vv Group 1 Group 2 COD uu umb e e 2 Select MENU A C A C o o OP Use f buttons to move to PICTURE MENU B D B D 3 Adjust the value BRIGHTNESS CONTRAST TINT COLOR and VIDEO MODE can
49. electing or deselecting Automatic Power On CMD 0x64 dU Send To LCD STX CMD Ex CMD Length Data Group ID Multi ID Mode Control ETX Receive From LCD 0x02 0x64 0x01 0x04 Value Variable Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Control Deselect Auto Power On 0x00 0 Select Auto Power On 0x01 1 Receive From LCD STX CMD Ex CMD Length Group ID Data Multi ID Mode Control Check Sum ETX Value 0x02 0x64 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Deselect Auto Power On 0x00 0 Select Auto Power On 0x01 1 Check Sum Execute Not operation after adding all the values in STX Data area 6 2 Get Display Model hisis the command for getting display information Itis available only during Power On Operative status CMD XxB9 SendToLCD STX CMD Ex CMD Length Data Group ID Multi ID Mode ETX Value 0x02 OxB9 0x01 0x03 Variable Variable
50. erial into the product It may cause a failure or shorten the life span container on it If the inside is wet it may cause electric shock or fire Do not touch the device when lightning Do not install in an unstable location strikes It may cause injury Avoid any action to damage the power cord or power plug It may cause fire or electric shock Do not alter or disassemble the product It may cause electric shock since high voltage is flowing inside Do not pull out the power plug with a wet Do not exceed ratings of AC outlet or extension cords It may cause failure hand It may cause electric shock Do not install the product where it may Make sure the product is not covered be exposed to direct sunlight or near with any object If the ventilation hole is any heating device It may shorten the blocked the inside temperature may rise product s life span or a eae to cause overheating resulting in fire Do not pull out or hang down the connection cable It may damage the cord to cause fire or electric shock Pull out the power plug by holding the plug Otherwise it may damage the power cord to cause fire or electric shock Ww O M The socket outlet should be installed Do not lean against the product or keep Do not put it at any place with much itleaned It may cause injury or failure humidity
51. esktops or create AMD Eyefinity display groups on supported hardware To configure your desktop click the triangle W on the desktop below Please select a display 53e 2 Eyefinity Configuration e This is the Eyefinity configuration for combining the desktop as one screen e Click the right button of the mouse on the display 1 in the Desktop layout part for the popup menus and select Display Group Create Group Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware To configure your desktop click the triangle W on the desktop below Common Display Tasks AMD Eyefinity Multi Display My Digital Flat Rotate b Bansi Identify gt gt Information gt Information iaga i zb e Then you will have the window for selecting layout as shown below You can select 4displays 4X1 or Adisplays 2X2 Select 4displays 2X2 and click Accept Select Layout 0 Eyefinity allows you to make a single desktop span a group of displays Please select a layout for the display group e The desktop is combined after the screen is turned off and on again Check the arrangement whether the screens are arranged in an orderly manner e If it is correct the desktop will be the following screen image
52. et 0x02 2 Control Deselect DHCP Disable 0x00 0 Select DHCP Enable 0x01 1 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 x64 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Deselect DHCP Disable 0x00 0 Select DHCP Enable 0x01 1 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Control Value Model Name 10 characters It is displayed as ASCII value Ex OLS 84 10NL Ox4F 0x53 0x2D 0x38 0x34 0x31 0x30 Ox4E Serial Num 13 Characters The range of the each character is 0x00 0 0x09 9 Check Sum Execute Not operation after adding all the values in STX Data area 6 3 Get Firmware Version This is the command for getting firmware version information Itis available only during Power On Operative status s CMD3 XF SendToLCD Check Sum Execute Not operation after adding all the values in STX Data area 6 5 LCD Network IP This is the command for configuring IP Address DHCP Disable Subnet Mask Default Gateway DNS Primary and DNS Secondary to allocate the Network IP directly for LCD Data Value STX 0x02 CMD OxF9 Ex CMD 0x01
53. he input Itis available only on Power On Operative status signal CMD 0x25 CMD 0x26 Send To LCD Send To LCD STX CMD Ex CMD Length siis ETX Data x a STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Group ID Multi ID Mode Control Value 0x02 0x25 0x01 0x04 Variable Variable Variable Variable 0x03 Value 0x02 0x26 0x01 0x04 Variable Variable Variable Variable 0x03 eee ID ipa e Multi ID 0x01 Fixed Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 ontrol Ux0U 0 Uxe4 100 Control Polycom 0x0 1 Cool 0x02 Normal 0x03 Warm 0x04 Custom 0x05 Receive From LCD Receive From LCD STX CMD ExCMD Length a Check S ETX Data 5 eng om STX CMD ExCMD Length CheckSum ETX Group ID Multi ID Mode Control Group ID Multi ID Mode Control Value 0x02 0x25 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Value 0x02 0x26 0x01 0x04 Variable Variable Variable Variable Variable Ox03 ae ID 0x01 Multi x PE Fixed Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed ode Read Get Response 0xUU U Write SeDResponse 0x02 2 Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control 0x00 0 0x64 100 Control TBD Check Sum Execute Not operation after adding all the values in STX Data area Check Sum Execute Not operation after adding all the values in STX Data ar
54. ion Temperature 9 35 C Humidity 35 75 Suitable operating time under 12 hours a day Do not install the set at the air tight condition Itis recommended to install the set with good ventilation Do not install the set at the place of direct sunlight or excessive exposure to lightings X Blackening stains or burning effect on the screen can be occurred by improper installation or use against the above recommended conditions gt Consideration for easier service When you design the exterior design for product system consider easier disassembly for possible service occasion in the future The sliding Universal Unit of ORION is recommended for easier service If service people can step into the backside of product system it can greatly reduce time and effort for service In case of higher locations consider the installation location and exterior design for easier service Application information If static images are displayed on the screen for a long time it causes burn in image Please keep the following instruction to optimize the lifetime and functions of the product Operating condition Temperature 20 15 C Humidity 59 20 96 Display pattern moving picture or regular switchover display Environmental condition Well ventilated place is recommended Power off and screen saver Periodical power off or screen saver is needed after long term static display zZ
55. lti ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Control Input Source configuration 0x10 is for the last input source at the time of the last Power Off 0x11 HDMI1A 0x12 HDMI11B 0x13 HDMI1C 0x14 HDMI1D 0x15 HDMIZ2A 0x16 HDMI2B 0x17 HDMI2C 0x18 HDMI2D 0x31 UHD 1 0x32 UHD 2 Check Sum Execute Not operation after adding all the values in STX Data area 7 3 KEY LOCK Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Value The range of Control value is from 0x00 0 to OxFF 255 Check Sum Execute Not operation after adding all the values in STX Data area 8 2 White Balance Control This is the command for adjusting the values for Gain RGB or Offset RGB of White Balance Since the adjusted values cannot be applied while Stand by status or without input signal LCD must be in operating condition with input signal CMD 0x27 Gain Red 0x28 Gain Green 0x29 Gain Blue OX2A Offset Red Ox2B Offset Green Ox2C Offset Blue t prevents the unexpected change for panel or set configuration Send To LCD CMD OxB0 Data Send To LCD STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Data STX CMD Ex
56. n Itis available only during Power On Operative status CMD Og Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Value 0x02 0x79 0x01 0x03 Variable Variable Variable 0x03 Ei Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Control Value The value for OFF is 0 0x00 and the duration can be selected between 3 0x03 and 10 0x04 Check Sum Execute Not operation after adding all the values in STX Data area 6 12 Get OSD Control Data This is the command for checking the OSD related configuration such as OSD Turn Off Time or OSD Info Display duration Itis available only during Power On Operative status Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x79 0x01 0x04 Variable Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Control 9600 1 0x01 14400 2 0x02 19200 3 0x03 38400 4 0x04 57600 5 0x05 115200 6 0x06 Check Sum Execute Not operation after adding all the values in STX Data area 6 10 OSD
57. ol This is the command to adjust the overall image and background brightness Itis available only on Power On Operative status Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed The adjusted value cannot be applied for Stand By or No input status So it can be applied when LCD is in operating condition with the input Mode Read Get Response 0x00 0 Write Set Response 0x02 2 signal Control Power Off 0x00 0 Power On 0x01 1 CMD 0x20 Check Sum Execute Not operation after adding all the values in STX Data area SendToLCD 3 3 Input Source Data P STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control hisis the command for changing the input source CMD 0xD1 Send To LCD Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Data Control 0x00 0 0x64 100 STX CMD Ex CMD Length ETX Group ID Multi ID Mode Input Source Receive From LCD Value 0x02 OxD1 0x01 0x04 Variable Variable Variable Variable 0x03 Data STX CMD Ex CMD Length heck ETX Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed j pu GroupID Multi ID Mode Control oc Mode Read Get 0x00 0 Write Set 0x02 2 l l l l Input Source 0x1 1 HDMI1A Ox12 HDMI1B 0x13 HDMI1C 0
58. on 40 operating instructions unless you are qualified to do so gt FACTORY RESET Configuration 41 6 Warning CAUTION These servicing instructions are for use by qualified service personnel only 07 User guide for UHD Graphic EAA A A EEE 42 To reduce the risk of electric shock do not perform any servicing other than that contained in the 08 PROTOCOL 2 operating instructions unless you are qualified to do so 09 Before calling for service iiit 80 M A 10 Applicable signals 81 if as l oh cored 0 a eee tere ree eee ee 82 12 Dimension ttt 84 01 Cautions gt Cautions for System installation gt Environmental condition for installation Since product panel is very sensitive for physical impact installation requires considerable caution Minimum clearance 20cm must be secured for smooth ventilation See page 6p 7p 5 45 nstallation must avoid air tight or near air tight places Improper ventilation causes malfunction and shortens product lifetime by rapid internal temperature rise If product has to installed at the improper ventilation additional ventilation openings or fans must be provided to keep the internal temperature between 0 35 C 5 lt G For ground of product and application devices it should be connected as frame ground Considering product Max power consumption check the main electric specification gt Recommended Operating Condit
59. ration after adding all the values in STX Data area ETX 0x03 The end of the code Fixed value c Communication Sequence Wait for 50msec for response after sending the command If there is no response it is recommended to resend the command Do not send the other command or change input resolution during command transmission T Te Command Transmission 2 Response Transmission Basic Command 3 1 Status This is the command for checking the current status of LCD Itis available only during Power On status CMD 0x87 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Value 0x02 0x87 0x01 0x03 Variable Variable Variable 0x03 Group ID Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Status Value 0x02 0x87 0x01 0x1C Variable Variable Variable ee Variable 0x03 Group ID Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Check Sum Execute Not operation after adding all the values in STX Data area Status 25 Byte No Data Length Explanation Ex OLS 8410NL Display Maag IO Byte OxAF OxAC 0x53 Ox2D 0x38 0x34 0x31 0x30 OxAE 2 Firmware Version 10 Byte ee Ex 192 168 00 04 0xCO OxA8 0x00 0
60. roduct design and specification can be changed for quality improvement without prior notice 82 Eee 12 Dimension gt OLS 8410NL OLS 8420NL gt OLS 8410T6L 1917 1977 2 25 55 3 25 55 3 1103 1163 2 25 5 25 593 95 1977 2 104 3 50 5 600 60 3 L1 Af VEN MN 331 6 10 M8 TAP Mounting Hole 10 M8 TAP Mounting Hole 1103 1163 2 400 SK 431 6 84 85 Memo 86
61. s of each 1Byte of IP Address Subnet Mask Default Gateway DNS Primary or DNS Secondary are from 0 0x00 to Group ID Multi ID range Program Group ID Mode Write Set Response 0x02 2 0x01 Multi ID 0x01 Fixed Control The ranges of each 1Byte of IP Address Subnet Mask Default Gateway DNS Primary or DNS Secondary are from 0 0x00 to 255 xFF Check Sum Execute Not operation after adding all the values in STX Data area 6 6 Get LCD Network IP This is the command for checking the configuration for LCD Network IP such as DHCP settings IP Address Subnet Mask Default Gateway DNS Primary and DNS Secondary CMD 0x75 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Value 0x02 0x75 0x01 0x03 Variable Variable Variable 0x03 Group Multi ID Range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x75 0x01 0x18 Variable Variable Variable Variable Variable 0x03 DHCP ON OFF IP Address Subnet Mask Default Gateway DNS Primary DNS Secondary 1Byte 4Byte 4Byte 4Byte 4Byte 4Byte
62. s55 e If it is not correct the screen can be arranged in disorder as shown below The following screen image is e Concurrently CCC window will be displayed as shown below an example and the incorrect arrangement can be vary If the arrangement is correct select Yes Select No for incorrect RADEON GRAPHICS Catalyst Control Center AMDA Preferences Creating and Arranging Desktops dX 7 Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware Presets r ff Is the display arrangement correct Desktop ik Management Display lt a AMD Eyefinity mum 4 L L 8 L L 8 t 96 Ey In case you select No follow the display arrangement procedure as shown below e Simultaneously one of 4 displays is turned on with blue color RADEON GRAPHICS Catalyst Control Center AMA Preferences P lt Creating and Arranging Desktops 7 gt Pinned Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware Presets Le In the group below click the position corresponding to the display lit Undo Done in blue Desktop Management Common Display Tasks AMD Eyetinity Multi Display My Digital Flat Panels Video gt Gaming
63. se a 2 EXIT MENU Press Exit button to exit from the menu 26 290 gt FIRMWARE Configuration e t displays the firmware version information 1 Select FIRMWARE from SETUP A menu Move to FIRMWARE and press MENU button to check current firmware version PICTURE SCREEN SETUP A SETUP B 2 EXIT MENU AUTO POWER DISPLAY MODEL FIRMWARE VERSION LAN BAUDRATE OSD SETUP A RESET Vv more clearly When you choose a lighter around Press Exit button to exit from the menu gt LAN Configuration It configures the IP address of the set to control via Ethernet 1 Select LAN from SETUP A menu Move to LAN and press MENU button to check current LAN configuration Configurations for DHCP ENABLE or DISABLE IP ADDRESS SUBNET MASK DEFAULT GATEWAY DNS PRIMARY amp SECONDARY and PORT can be checked PICTURE SCREEN da SETUP A SETUP B 2 EXIT MENU AUTO POWER DISPLAY MODEL FIRMWARE VERSION LAN BAUDRATE OSD SETUP A RESET Vv more clearly When you choose 8 Press Exit button to exit from the menu s BAUD RATE Configuration t adjusts the communication rate to control the set via RS 232C 1 Select BAUD RATE from SETUP A menu Move to BAUD RATE and press MENU button PICTURE SCREEN p SETUP A SETUP B AUTO POWER DISPLAY MODEL FIRMWARE VERSION LAN BAUDRATE OSD SETUP A RESET Vv ore
64. t from the menu after adjusting the value COLOR ADJUSTMENT e Adjust the depth of the screen color e The depth of color will be thicker as the value goes higher As the value goes lower the depth of color will be getting thinner and go to black and white 1 Select COLOR from PICTURE Menu Select COLOR and move mbbuttons to adjust the value 9 PICTURE BRIGHTNESS CONTRAST SCREEN TINT COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B 2 EXIT MENU Press Exit button to exit from the menu after adjusting the value 0 gt VIDEO MODE SELECTION e Adjust the color temperature of the screen 1 Select VIDEO MODE from PICTURE Menu Select VIDEO MODE and move f buttons to select a VIDEO MODE of your choice among POLYCOM COOL NATURAL WARM and CUSTOM f6 PICTURE BRIGHTNESS CONTRAST SCREEN TINT COOL NATURAL WARM VIDEO MODE CUSTOM COLOR SETUP A PICTURE RESET SETUP B CUSTOM configuration 1 Select CUSTOM from VIDEO MODE Detailed values for RGB can be controlled by pressing MENU button after selecting CUSTOM 0 PICTURE BRIGHTNESS CONTRAST POLYCOM SCREEN TINT COOL _ NATURAL WARM COLOR SETUP A VIDEO MODE PICTURE RESET SETUP B 2 Adjust values USER R O USER G O and USER B O mean OFFSET RED OFFSET GREEN and OFFSET BLUE respectively USER R USER G and USER B are GAIN RED GAIN GREEN and GAIN BLUE
65. tion after adding all the values in STX Data area 5 5 Get Screen Control Data Get the adjusted data for Horizontal and Vertical Position Aspect Ratio Video Mute Blank Unblank and Panel Key Lock Key Lock Unlock CMD 0x92 Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Value 0x02 0x93 0x01 0x03 Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x93 0x01 0x08 Variable Variable Variable Variable Variable 0x03 H Position V Position Aspect Ratio Video Mute Panel Key Lock 1Byte 1Byte 1Byte 1Byte 1Byte Value Variable Variable Variable Variable Variable Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Control each data is 1 Byte and the rages of H Position is 0 0x00 100 0x64 V Position is 0 0x00 100 0x64 For the Aspect Ratio 1 0x01 is 16 9 and 2 0x02 is 4 3 For the Video Mute 0 0x00 is Blank and 1 0x01 is Unblank For the Panel Key Lock 0 0x00 is Unlock 1 0x01 is Key Lock Check Sum Execute Not operation after adding all the values in STX Data area 6 SETUP A Command 6 1 Auto Power This is the command for s
66. up below click the position corresponding to the display lit in blue Desktop Management w Common Display AMD Eyefinity Mult Display My Digital Flat Panels gt Video 2 gt Gaming he o gt Performance gt Audio gt Information A The next procedure is Bezel Compensation Since it is not a necessary procedure click No Then all configurations for CCC are completed The desktop with UHD resolution will be displayed as shown below RADEON GRAPHICS Catalyst Control Center Preferences Creating and Arranging Desktops Enable arrange duplicate and rotate desktops or create AMD Eyefinity display groups on supported hardware Do you want to compensate for the bezels around the edges of your displays Common Display Tasks 4 AMD Eyefinity Multi Display My Digital Flat Panels 62 63 08 PROTOCOL Introduction This document contains the communication PROTOCOL between LCD and its control devices for better use t focuses on the brief functional explanation and communication protocol without detailed technical matters 1 Communication Setting Transmission type Asynchronous Serial Communication Baud Rate Select one rate among 9600bps 14400bps 19200bps 38400bps 57600bps or 115200 bps Parity bit None Stop bits 1 2 Protocol Format 2 1 Send To LCD
67. x04 3 IP Address 4 Byte 0x00 Ox2E 0x38 0x30 Ox2E 0x30 0x31 0x41 Ox2E Ox4F 0x11 HDMI 1A 0x12 HDMI 1B 0x13 HDMI 1C 0x14 HDMI 1D 4 Input Source 1 Byte 0x15 HDMI 2A 0x16 HDMI 2B 0x17 HDMI 2C 0x18 HDMI 2D 0x31 URDAI 0x32 UAD 2 3 2 Power On Off Power On Off Power On command is available only during Power Off Stand by status Power Off command is available only during Power On Operative status CMD 0x10 65 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX Group ID Multi ID Mode Value 0x02 0x01 0x03 Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Write Set Response 0x02 2 Check Sum Execute Not operation after adding all the values in STX Data area Picture Control Command Send To LCD Data STX CMD Ex CMD Length ETX Group ID Multi ID Mode Control Value 0x02 0x10 0x01 0x04 Variable Variable Variable Variable 0x03 Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get 0x00 0 Write Set 0x02 2 Control Power Off 0x00 0 Power On 0x01 1 Receive From LCD Data STX CMD Ex CMD Length Check Sum ETX GroupID Multi ID Mode Control Value 0x02 0x10 0x01 0x04 Variable Variable Variable Variable Variable 0x03 4 1 Brightness Contr
68. x14 HDMI1D 0x15 HDMI2A 0x16 HDMI2B 0x17 HDMI20 Value 0x02 0x20 0x01 0x04 Variable Variable Variable Variable Variable 0x03 0x18 HDMI2D 0x31 UHD 1 0x32 UHD 2 Receive From LCD Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed Mode Read Get Response 0x00 0 Write Set Response 0x02 2 ET d Data T Control 0x00 0 0x64 100 X engt eck Sum ETX x Not l l in CTX GroupID Multi ID Mode Contrel Check Sum Execute Not operation after adding all the values in STX Data area Value 0x02 OxD1 0x01 0x04 Variable Variable Variable Variable Variable 0x03 4 2 Contrast Control Group ID Multi ID range Program Group ID 0x01 Multi ID 0x01 Fixed This is the command to adjust the image brightness in relationship to the background Mode Read Get Response 0x00 0 Write Set Response 0x02 2 Itis available only on Power On Operative status Input Source 0x11 HDMI1A 0x12 HDMI1B 0x13 HDMI1C 0x14 HDMI1D 0x15 HDMI2A 0x16 HDMI2B 0x17 HDMI2C 2 The adjusted value cannot be applied for Stand By or No input status So it can be applied when LCD is in operating condition with the input 0x18 HDMI2D 0x31 UHD 1 0x32 UHD 2 x T i signal Check Sum Execute Not operation after adding all the values in STX Data area CMD 0x21

Ultra High Definition LED

Contents

Download Pdf Manuals

Related Search

Related Contents