Home

User-Manual

1. Low Profile Universal TV Mount 32 to 65 Installation Instructions Fixed Flat Screen TV Wall Mount Material Cold Rolled Steel Plate s 50 kes Important If you have difficulty following or understanding these installation instructions please consult a qualified installation specialist ZX Caution Prior to installation of this product the installation instructions should be read and completely understood The installation instructions must be read to prevent personal injury and property damage Keep these installation instructions in an easily accessible location for future reference This mount contains small parts which can act as a choking hazard if swallowed CAUTION The maximum load capacity is 110 Ibs Use with products exceeding the maximum load capacity may cause serious injury See apparatus instructions Thewall structure must be capable of supporting at least five 5 times the maximum load capacity as indicated If not the wall must be reinforced Recommended mounting surfaces wood stud and solid flat concrete brick If the mountis to be installed on any surface other than wood studs solid concrete orbrick use suitable hardware not included but commercially available Donot install on a structure that is prone to vibration movement or chance of impact Failure to do so could result in damage to the display and or damage to the mounting surface Donotinstall near heater fireplace air
2. Mount 32 to 65 is shipped with the proper installation hardware and parts Make sure that none of the items are missing or damaged before starting the installation If there are any missing and or damaged parts please stop the installation and contact your place of purchase Tools Required Electronic stud finder for wood stud installation Phillips head screw driver Socket and or wrench set Electric drill 3 16 5mm drill bit for wood stud installation 3 8 10mm masonry drill bit for concrete brick wall installation Step 1 Wall Plate Installation A Wood Stud Installation NOTE For secure wood stud mounting the wall plate must be mounted to two studs atleast 16 apart 1 Use a high quality electronic stud finder commercially available to locate dead center of two adjacent wood studs and mark the location with an awl or pencil Figure 1 a Attach the Bubble level to the wall plate and with the help of an assistant ensure the wall plateis level position the wall plate against the wall in the desired mounting location figure 1 b 3 Mark the right upper and lower and the left upper and lower positions of the small horizontal slots that are in alignment with the wood studs 4 You should mark four positions total Take 1b down the wall plate 5 Next pre drill a 3 16 hole to a depth of 3 in the wood stud at each marked location figure 1 0 6 Position the wall plate against th
3. conditioning in direct sunlightor any other heat producing source Failure to do so may result in damage to the display and could increase the risk of fire Make sure no water or natural gas lines are present where the mount is to be installed Cutting or drilling into water or natural gas lines could cause personal injury or property damage When mounting to wood studs it is recommended thata maximum 5 8 particle board be used When mounting to a wall that contains wood studs confirm the dead center of the wood stud prior to installation itis recommended that the wood studs be a minimum of 16 apart if applicable Proper installation procedure by yourself or a qualified service technician as outlined in the installation instructions must be adhered to Failure to do so could result in serious personal injury This productis intended for indoor installation use only Premature product failure or serious personal injury could occur if this product is used outdoors tis recommended that two people perform the installation Injury and or damage can result from dropping or mishandling the display If you don t understand these installation instructions please consult an installation Hardware Kit x4 Bolt x4 x4 Washer x4 Retinal QOQ y w y x4 Spacer et M5x90 ey MBs way Mean 1 J K xd M6x15 x4 M8x30 x4 M8x15 x1 Bubble level Important The Low Profile Universal TV
4. e wall and line up the mounting slots with the drilled holes Check the bubble level to verify that the wall plate is level 7 For each location insert Bolt A and Washer C into the wall figure 1 d 8 Tighten each bolt with an open ended wrench or socket wrench by turning clockwise until tight Rp Fm CAUTION Do not over tighten the bolts doing so may cause unnecessary damage to the wall Avoid excessive torque CAUTION Do not release the wall plate until it is properly mounted and secured to the wall B Concrete Brick Wall Installation Note The Plastic Anchors must be used for concrete and brick wall installation 1 Attach the Bubble level to the wall plate with the help ofan assistant place the wall plate into position against the wall using the bubble level to ensure it is level figure 1 e Mark four holes to be used for securing the mount and place the wall plate aside Locate be the holes directly into the concrete or brick never into the mortar between the blocks Drill holes using an electric drill and 3 8 masonry drill bit to a depth of 2 at the positions you marked Insert a Plastic Anchor B into each hole figure 1 f If necessary a hammer can be used to lightly tap each Plastic Anchor into place so that they are flush with the wall Onceall of the Plastic Anchors arein place move the wall plate back into position Check the bubble level to verify that t
5. he wall plate is level Insert Bolt A and Washer C into each Plastic Anchor B and tighten Do not fully tighten until all bolts are in place figure 1 8 Step 2 Display Bracket Installation The installation kit includes screws of various diameters and lengths to ensure optimal installation 1 Place your TV screen down on a soft flat surface and locate the threaded mounting points that are located on the back of the display 2 Determine which screw F G H 1 K is of the correct length by carefully inserting a straw or toothpick and mark how deep the mounting point is 3 According to the size of the display s hole choose the corresponding screw and hole on the Rectangular washer D then thread them in line figure 2 a 4 If your display has a curved back or recessed thread mounting point place Spacer E between the display bracket and display and then choose screw F G H I J K to match figure 2b See a Fg OD F G H T J K Step 3 Final Installation and Adjustment 1 Hook the display bracket over the top of the wall plate figure 3 a 2 Rotate theboltat the bottom of the display bracket to tighten and secure the TV to the wall plate figure 3 b 3b Maintenance Check the mounting screws every two months for tightness Technical Support and Warranty QUESTIONS SIIG s Online Supporthas answers Simply visitour websiteat wa siig comand click Supp
6. operly packtheproductforshipping Allsoftware cable s and any other accessories thatcame with the original package must be included Clearly writeyourRMA number on thetopofthereturned package SUG wll refuse toacceptany shipping package nd willnot be responsible fora product returned withoutan RMA number posted on the outside of the shipping carton Youare responsible for the cost of shipping toil SUG Inc 6078 Stewart Avenue Fremont CA 94538 3152 USA RMA SIIG will ship the repaired or replaced product via Ground in the U S and International Economy outside ofthe US atnocost tothe customer Ship the product to the following address About SIIG Inc Founded in 1985 SUG Inc isa leading manufacturer of T connectivity solution including Serial ATA and Ultra ATA Controllers Fire Wire SB and legacy I O adapters tat ridge he connection between Desktop Notebook Systems and external peripherals SIG continues to grow by adding A V and Digital Signage connectivity Solutions togurextensive portfolio Allgentered around the distribution and switching of A V signalsoverCAT3 these products include matra switches distribution amplifiers extenders converters spillers cabling and SIGisthe premier one stop sourceof upgrades andiscommitted to providing high quality products while keeping Sra aa He E a eel Below deectveretunk Fatesin the industry Our produci offercomprehensive user manuals user friendly features and most produc
7. ort Our online support database is updated daily with new drivers and solutions Answers to your questions could be just a few clicks away You can also submit questions online and a technical support analysts will promptly respond SllG offers a 3 year manufacturer warranty with this product This warranty covers the original purchaser and guarantees the product tobe free of any defects in materials or workmanship for three 3 years from the date of purchaseof the product SIG will at our discretion repair or replace with an identical product or product having similar features and functionality the productifdefectivein materials or workmanship This warranty gives you specific legal rights and you may alsohave other rights which vary from statetostate Pleasesee our website for more warranty details Ifyou encounter any problems with this product please fallow the procedures below A Ifitis within the store s return policy period please return the product tothe store where you purchased i B Ifyourpurchasehas passed thestor s return policy period please follow thesestepstohavethe productrepaired orreplaced Step1 Submit your RMA request Go to www siig com click Support then Request A Product Replacement to submit a request to SUGRMA or faxa request to 510 657 5962 Your RMA request will be processed if the productis determined tobe defective an RMA number willbe issued Step2 After obtaining an RMA number ship the product Pr
8. ts arebacked bya etime warranty ie product can be found in many computer retail stores mail order catalogs and e commerce sites in the Ameficas aswellaethrough major distributors system integrators and VARS Low Profile Universal TV Mount 37to65 isatrademark ofSIIG Inc SIG and theSIIG logoareregistered trademarks ofSIIG Inc Allothernamesused inthispublicationareforidentification only anc maybetrademarksoftheir respective March 2015 Copyright 2015 by SIIG Inc Al rights reserved

User-Manual

Contents

Download Pdf Manuals

Related Search

Related Contents