Home

Manual

1. 19 Micro USB Port Mobile device connection This maximum transmission distance was tested in a lab environment and is for reference only The maximum operating distance may vary depending on conditions in your immediate surroundings Fly Safe DJI encourages you to enjoy flying your Phantom 3 Professional in a safe responsible and smart way To do this it is important to understand some basic flight guidelines both for your protection and for the safety of those around you 1 Fly in Open Areas Always fly in locations that are free and clear of buildings trees power lines and other obstacles Do not fly above or near people or animals 2 Maintain Control at All Times Even when using DJI autopilot functions such as Auto Takeoff Auto Landing and Auto Return to Home always keep your hands on the Remote Controller and maintain control of your aircraft when it is in flight 3 Maintain Line of Sight Keep your aircraft in sight at all times and avoid flying behind buildings or other obstacles that may block your view 4 Monitor Your Altitude For the safety of full sized aircraft and other air traffic always fly at altitudes less than 400 feet 120 meters above ground level or in line with your local laws and regulations Visit http flysafe dji com no fly for more information on critical safety features such as No Fly Zones e Calibrating the Compass Make sure
2. Check Battery Levels Pressing the Power Button once on either your Intelligent Flight Battery or Remote Controller displays the battery level Be sure to fully charge both batteries before your first flight Low e Battery Level High SN 0 0200 g yy Low e Battery Level High xy 00 0 4 Charging the Batteries e Only use the official DJI Phantom 3 Professional charger Remove the Intelligent Flight Battery from the aircraft before charging e t is recommended that you turn off the Intelligent Flight Battery or Remote Controller before charging e Connect the charger to a suitable power source 100 240V 50 60HZ e Connect the charger to the Intelligent Flight Battery or Remote Controller The LEDs will display the current charge level and when fully charged they will automatically turn off Pale Remove the Intelligent Flight Battery 5 Preparing the Remote Controller Tilt the Mobile Device Holder to the desired position and then adjust the antennas as shown The strength of the Remote Controller s signal will fluctuate depending on the positions of the antennas The transmission signal between the aircraft and Remote Controller will be strongest within the range illustrated here If the signal is weak adjust the positions of the antennas and fly the aircraft closer to achieve optimal signal performance Press the
3. releasing it and then pressing and holding for 2 seconds Insert the Intelligent Flight Battery into your Phantom 3 Professional Turn on the battery by pressing the power button once releasing it and then pressing and holding for 2 seconds Ensure the LED on your Remote Controller is green indicating it is ready to be used Connect your mobile device to the Remote Controller with a USB cable and launch the DJI Pilot app Follow the instructions within the app In the app tap Camera Ensure your Phantom 3 Professional is ready to fly by completing the on screen Checklist Beginner Mode is enabled by default when you launch the DJl Pilot app for the first time The aircraft s altitude and flight distance are restricted when flying in Beginner Mode You can disable Beginner Mode in the Settings Page of the DJI Pilot app Calibrate the compass by tapping the Aircraft Status Bar in the app and selecting Calibrate Then follow the on screen instructions Attach the propellers with a black nut onto the motors with a black axis and spin them counter clockwise to secure Attach the propellers with a gray nut onto the motors with a gray axis and spin them clockwise to secure A e Be sure to match all the propellers to motors with the correct colors and tighten by hand before flying elf you wish to record photos or videos insert a Micro SD card into the Camera s Micro SD Card Slot e The Flight Mode Switch
4. V Capacity Voltage Battery Type Energy Net Weight Operating Temperature Max Charging Power X This Quick Start Guide is subject to change without prior notice 4480 mAh 15 2V LiPo 4S 68 Wh 365 g 10 C to 40 C 100 W C 1313 roms E FCC ID SS3 WM3231503 FCCID SS3 GL3001501 This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Preparing Your Phantom 3 Professional Before Flying Read the User Manual and watch the video tutorials in the DJI Pilot app or on the official DJI website www dji com and read the following documents included in the box before using your Phantom 3 Professional for the first time Phantom 3 Professional Quick Start Guide Phantom 3 Professional Advanced Safety Guidelines and Disclaimer Phantom 3 Professional Advanced Intelligent Flight Battery Safety Guidelines In the Box 1 Download the DJI Pilot App 2 Watch the Tutorial Videos Search DJI Pilot on the App Store or Google Play and Watch the tutorial videos on www dji com or in download the DJI Pilot app to your mobile device the DJI Pilot app DJI Pilot app Phantom 3 tutorial videos A e For the best experience use a mobile device that runs OS 8 0 or above or Android 4 1 2 or above 3
5. button on the side of the Mobile Device Holder to release the clamp Place your mobile device into the clamp and adjust it so that the mobile device is held securely in place Connect your mobile device to the Remote Controller with a USB cable Plug one end of the cable into your mobile device and the other end into the USB port on the back of the Remote Controller A e To avoid signal interference do not use other 2 4GHz devices when flying 6 Flight Controls Here are the default flight controls Mode 2 The left stick controls altitude and rotation while the right stick controls the forward backward left or right movements The gimbal dial controls the camera s tilt Left Stick Right Stick Gimbal Dial A e You can customize or change these controls through the DJI Pilot app 7 Getting Ready for Takeoff Remove the gimbal clamp as shown on the right Place your Phantom 3 Professional on a flat surface in an open space with the nose facing away from you Then follow the steps below in this order all ll Toggle the Flight Mode Switch on your Remote Controller to the right P Mode P Mode is Positioning Mode A Mode is ATTI Mode and F Mode is Function Mode Turn on the Remote Controller by pressing the power button once
6. mid flight otherwise the aircraft will crash Only stop the motors when on the ground or as required in emergency situations to reduce the risk of damage or injury e You cannot takeoff if the Intelligent Flight Battery is not sufficiently charged and the Critical Low Battery Warning is active e The Intelligent Flight Battery must warm up if the outside temperature is low A warning will appear in the DJI Pilot app in this scenario e Once spinning the rotating propellers can be dangerous Do not start the motors when there are people nearby and always fly in a wide open area e Power off your Phantom 3 Professional before switching off the Remote Controller after landing e Return to Home 1 Press and hold the Return to Home Button on your 2 The DJI Pilot app will warn you if your Phantom 3 Remote Controller until the LED surrounding the button Professional s battery level falls under a certain level This starts blinking white and starts beeping Your Phantom warning threshold can be set in the app The aircraft will 3 Professional will return to the set Home Point Press land immediately if the battery power reaches a critical the button once to stop the procedure level and the Critical Low Battery Level Warning appears 3 Failsafe The Phantom 3 Professional will enter Return to Home Mode if the signal to the Remote Controller is lost A e While returning home you can still control your Phantom 3 RTH Button The
7. to calibrate the compass at every new flight location The compass is very sensitive to electromagnetic interference which can cause abnormal compass data leading to poor flight performance or even failure Regular calibration is required for optimal performance 1 DO NOT calibrate your compass where there is a chance of strong magnetic interference such as magnetite parking structures and steel reinforcements underground 2 DO NOT carry ferromagnetic materials with you during calibration such as keys or cellular phones 3 DO NOT calibrate beside massive metal objects 4 If the Aircraft Status Indicators are showing solid red then try to calibrate again If they are blinking red and yellow alternately after placing the aircraft on the ground the compass has detected magnetic interference Change your location e Environmental Considerations 1 Do not fly in severe weather conditions This includes high winds speeds of 22 mph or 10 m s or more snow rain and fog 2 Only fly in open areas Tall buildings and steel structures may affect the accuracy of the on board compass and GPS signal 3 Avoid obstacles crowds high voltage power lines trees and bodies of water 4 Minimize electromagnetic interference by avoiding areas with high levels of electromagnetism including mobile phone base stations radio transmission towers or Wi Fi hotspots 5 Aircraft and battery performance are subject to environmental factors such as air d
8. PHANTOM 3 Quick Start Guide V1 0 Phantom 3 Professional It s time to meet your Phantom 3 Professional The Phantom 3 Professional s camera records video at up to AK and captures 12 megapixel photos Review the diagram below for a full list of your Phantom 3 Professional s parts 1 Gimbal and Camera 8 Aircraft Status Indicators 2 Vision Positioning System 9 Antennas 3 Camera Micro SD Card Slot 10 Intelligent Flight Battery 4 Aircraft Micro USB Port 11 Power Button 5 Front LEDs 12 Battery Level Indicators 6 Motors 13 Link Button 7 Propellers 14 Camera Micro USB Port Remote Controller This powerful Remote Controller allows you to pilot and maneuver your Phantom 3 Professional at distances over 6 000 feet 2 km away while putting selected camera controls at your fingertips Built into your Remote Controller is a rechargeable LiPo battery and DJI Lightbridge which when paired with a compatible mobile device gives you a live HD view from the Phantom s camera Power Button Return to Home RTH Button Control Sticks Status LED Battery Level LEDs Power Port Mobile Device Holder o NoN AWON gt Small Device Positioning Tabs such as mobile phone 9 Antennas 10 Handle Bar Folded 11 Gimbal Dial 12 Camera Settings Dial 13 Video Recording Button 14 Flight Mode Switch 15 Shutter Button 16 Playback Button 17 C1 C2 Buttons Customizable 18 USB Port
9. app s RTH Button Professional s altitude to avoid any obstacles Appendix Aircraft Status Indicators Remote Controller Status LED Camera Controls Slowly Safe to fly GPS working Remote Controller is functioning normally e Adjust the camera parameters using gt but is not connected to the aircraft the Camera Settings Dial on the var Xe RN pl Remote Controller is functioning normally Remote Controller or through the DJI y 9 and is connected to the aircraft Pilot app Press the Shutter Button or Slowly P ATTI or ATTI Mode B B B Aircraft Low Battery Level Warning EO O ERDE N photos or record videos Sie or Remote Controller error Quickly Not connected to the Remote Controller 9 B B Remote Controller has been e Adjust the gimbal s tilt using the idle for 5 minutes Gimbal Dial Nis Slowly Low Battery Level Warning e Download photos and videos from e Quickly Critical Low Battery Level Warning ine MicroSD card to your mobile Solid Critical error device through the DJI Pilot app az You can also use a SD card reader z gt Blinking Alternately to export files to your computer Compass calibration required For more information http www dji com phantom3 2015 DJI All Rights Reserved Designed by DJI Printed in China PHANTOM 3 www dji com
10. deo Storage Supported File Formats Supported SD Card Types Operating Temperature Range e Remote Controller Operating Frequency Max Transmission Distance Video Output Port Operating Temperature Range Battery Mobile Device Holder Transmitter Power EIRP Working Voltage e Charger Voltage Rated Power 1280 g 5 m s 3 m s 16 m s ATTI mode no wind 6000 m Approximately 23 minutes 0 C to 40 C GPS GLONASS Pitch 90 to 30 lt 8 m s Altitude 2 m 30 cm 300 cm 30 cm 300 cm Y I O PA S lt y gt KB Y S gt IS I Surface with clear pattern and adequate lighting Lux gt 15 Sony EXMOR 1 2 3 Effective pixels 12 4 M total pixels 12 76 M FOV Field Of View 94 20 mm 35 mm format equivalent f 2 8 100 3200 video 100 1600 photo 8 s 1 8000 s 4000 x 3000 Single shot Burst shooting 3 5 7 frames Auto Exposure Bracketing AEB 3 5 bracketed frames at 0 7EV Bias Time lapse UHD 4096x2160p 24 25 3840x2160p 24 25 30 FHD 1920x1080p 24 25 30 48 50 60 HD 1280x720p 24 25 30 48 50 60 60 Mbps FAT32 exFAT Photo JPEG DNG Video MP4 MOV MPEG 4 AVC H 264 Micro SD Max capacity 64GB Class 10 or UHS 1 rating required 0 C to 40 C 2 400 GHz 2 483 GHz 2 km outdoors and unobstructed USB 0 C to 40 C 6000 mAh LiPo 2S Tablets and smartphones FCC 20 dom CE 16 dbm 12A 74V 17 4V 100 W e Intelligent Flight Battery PH3 4480 mAh 15 2
11. ecorded when the GPS Note that the Vision Positioning system may not work properly when Signal icon in the DJI Pilot app is either yellow or green the Phantom 3 Professional is flying over water over surfaces without The aircraft will return to the Home Point automatically in the a clear pattern or in a low light environment following scenarios all require a strong GPS signal Smart RTH When the RTH button on the Remote Controller E x EEE or in the DJI Pilot app is pressed Low Battery RTH A notification will appear in the DJI Pilot Return to home app requesting the pilot to take action when the battery level falls under a certain level y Failsafe RTH When the Remote Controller s signal is lost 6 e While returning to the Home Point the aircraft s altitude can be adjusted to avoid obstacles Tall buildings may affect the Remote Controller s signal The Failsafe Return to Home procedure will be triggered if the signal is lost Be sure to fly higher than any nearby buildings to avoid crashing Appendix e Aircraft Weight Including Battery Max Ascent Speed Max Descent Speed Max Speed Max Flight Altitude Max Flight Time Operating Temperature Range GPS e Gimbal Controllable Range e Vision Positioning Velocity Range Altitude Range Operating Range Operating Environment e Camera Sensor Lens ISO Range Electronic Shutter Speed Image Max Size Still Photography Modes Video Recording Modes Max Bitrate of Vi
12. ensity and temperature Be very careful when flying 19 600 feet 6 km or more above sea level as battery and aircraft performance may not be at peak efficiency 6 The Phantom 3 Professional cannot operate in P Mode or use GPS at polar latitudes Only ATTI Mode and the Vision Positioning system will be operational e P Mode 1 In this mode the Phantom 3 Professional can use GPS and the Vision i P GPS Positioning Q Positioning system allowing it to hover accurately in position indoors and out When GPS is available a Home Point will be locked so that the Phantom 3 Professional can Return to Home if the Remote Controller signal is lost E E To enable P Mode toggle the Flight Mode Switch to the P position 9 feet 10 inches Vision Positionin There are three states in P mode 9 Altitud P GPS GPS works best when outdoors and in a wide open area Your SE Phantom 3 Professional uses GPS to hover in place when there is a strong GPS signal foot P OPTI If GPS is not available the aircraft can use the Vision Positioning i l system to hover accurately e Return to Home P ATTI Neither GPS nor the Vision Positioning system are available When there is a strong GPS signal the aircraft will be able to The aircraft will only use its barometer for altitude and other on board ecord a Home Point and return to that Home Point when sensors for attitude stabilization required The Home Point location is r
13. is locked in P Mode by default Refer to the User Manual to learn how to unlock the switch and change to other modes e When not in P mode the Phantom 3 Professional will only maintain altitude not position and will drift with wind or user input Return to Home is not available in F mode 8 Flight Before taking off make sure the Aircraft Status Bar in the DJI Pilot app Safe to Fly GPS indicates Safe to Fly GPS or Safe to fly non GPS if flying indoors e Auto Takeoff and Landing Your Phantom 3 Professional can automatically takeoff and land at the tap of a button in the Camera screen of the Dul Pilot app hover at 4 feet 1 2 meters Tap and slide to confirm automatic takeoff The aircraft will automatically takeoff and The aircraft will automatically land Tap and slide to confirm automatic landing ciji e Manual Takeoff and Landing Stick configurations are for MODE 2 Start the motors by pulling both control sticks to the bottom To land gently pull the left stick throttle stick inside or outside corners Release the sticks once the down to lower the aircraft until it touches the motors start Slowly push the left stick throttle stick up to ground Then pull both sticks to the bottom inside takeoff corners to stop the motors Start Stop the motors Left stick up Slowly Left stick down Slowly aAA Ae K M y A e Never stop the motors

Manual

Contents

Download Pdf Manuals

Related Search

Related Contents