www.autoobd2.de
Contents
1. top of the white 4 pins connector IMPORTANT the following instructions indicate how to connect and install your SEAS module on the original AdBlue system of the truck The number displayed and the colour of the conductors of the AdBlue system are referred to MAN TGX18 440 year 2009 these details may vary according to different production lots or vehicle equipment Please refer to the schemes layouts supplied with the MAN technical manual to identify the CAN Bus line of the AdBlue system its protection fuse and the power feeding The main working procedure of SEAS modules does not vary MAN_eng doc Pagina 2 di 5 Ver 0 1 ww aut 00bd2 de Installation on the vehicle Before proceeding please make sure that the following conditions are respected e NO faulty codes memorized in the original ECU e AdBlue liquid higher than the reserve level e Vehicle batteries disconnected from the electrical circuit The SEAS module is supplied with 5 conductors e Power feeding activation RED 15 to be connected to a 24 Volt source under key 24 Volt enabled when the engine key is in ON position preferably to the same source that enables the AdBlue system working This connection will supply power to the SEAS module when the engine key is in ON position dashboard ON BLACK earth to be connected to an earth available preferably the same as AdBlue GREY 30 to be connected to a 24 Volt source always avail2. ED is turned on too e After approx 1 minute the YELLOW LED switches off and a GREEN LED will turn on e Switch off the dashboard key OFF After this procedure the SEAS module will be activated whenever the dashboard will be turned on key ON The result will be e lf the F738 fuse is installed the original AdBlue system will be working and the two LED will always be on e lf the F738 fuse is not installed the original AdBlue system will not be working and the SEAS module will be activated the two LED will be flashing All the operations on the F738 fuse have to be performed ONLY with the dashboard switched off key OFF SEAS module diagnostic table of LED Light Emission Diode DASHBOARD YELLOW LED GREEN LED State of the SEAS module KEY OFF No power feeding jen Auto acquiring operations completed Data saved module not activated Not programmed DN UFF Programmed waiting for self learning KEY ON working intermittent Data saved module ACTIVATED MAN_eng doc Pagina 5 di 5 Ver 0 1 ww aut 00bd2 de
3. SEAS INSTRUCTIONS MAN Please read the complete document before starting the installation Brand assignment SEAS add on module is delivered NOT PROGRAMMED therefore a brand MAN in this case must be set with computer and specific program SETUP TRUCK This procedure can be achieved both before and after the installation on the vehicle if after the installation the vehicle power batteries must be disconnected during the operations e Connect the programming cable to the USB port of your PC e Connect the programming cable to the SEAS module by using the white 4 pins connector during this operation the LED Light Emission Diode of the SEAS module will be off e Run the program SimulaCan select it from the list of programs installed on your pc e Proceed as follow ma SETUP TRUK AEK Select Start Wait for next screen displayed the time required can vary according to the quantity of virtual COM installed MAN_eng doc Pagina 1 di 5 Ver 0 1 ww aut 00bd2 de ra SETUP TRUK 15 x If the connection is successfully achieved serial communication recognized and accepted the program will display this page you can now select MAN brand Select Send PROG When the programming operation is completed the yellow LED on your SEAS module will turn on Select Quit to close the program SimulaCan e Disconnect the programming cable of your SEAS module and place the specific cover on
4. able of AdBlue system necessarily BETWEEN the F738 protection fuse and the AdBlue system e CAN Bus line connection The two conductors plaited together must be connected to the CAN Bus line of the AdBlue system WHITE CAN H to be connected to CAN H of the system that must be simulated BROWN CAN L to be connected to CAN L of the system that must be simulated The connections must be made under the box of the connectors locate under the protection covers of radiator driver and passenger side The SEAS module can be fixed in a support external because is completely waterproof or in the fuse box that communicate on the passenger side The 5 conductors of SEAS module must be soldered to the 5 conductors of the AdBlue system SEAS Module MAN AdBlue system CAN L BROWN CAN L Pink 192 CANH H WHITE p GANH H pink 191 pink 191 24 a O always available 30 Activation 30 GREY Between F7amand AUBILE White 90 004 24V under key 15 RED 24V UNDER KEY 15 Pink 15 038 MAN_eng doc Pagina 3 di 5 Ver 0 1 ww aut 00bd2 de 15 15001 30010 30 l dl Fuse F737 G G Fuse F738 7 5 Amp 20 Amp PIN to connect the original AdBlue ECU EARTH MAN_eng doc Pagina 4 di 5 Ver 0 1 www aut 00bd2 de Notes on the Activation signal The SEAS module and the original AdBlue system cannot be both activated at the same time the grey Activation wir
5. e 30 is utilized to enable automatically the SEAS module working For this reason it is extremely important to connect this wire to a 24 Volt source always available battery moreover the soldering operation must be done between the 20 Amp F738 fuse and the AdBlue module Consequently if you want to stop and exclude the original AdBlue system working it is enough to remove the F738 fuse before starting the engine The SEAS module will automatically be activated To reset the original AdBlue system working it is enough to re install the F738 fuse before starting the engine The SEAS module will be de activated IMPORTANT the F738 fuse is located into the fuse amp relay box under the dashboard passenger side It might be identified with a written SCR There might be other fuses with the same written SCR but characterized by a lower value of Ampere these fuses do NOT have to be considered Self learning CAN Bus line Once the SEAS module is fully connected to the electrical circuit of AdBlue system and after the identification of the F738 fuse controlling the power feeding of the AdBlue system the vehicle power batteries can be reconnected The SEAS module acquires inputs from the CAN Bus line the first time the dashboard is turned on key ON but engine still OFF Please make sure that F738 fuse is correctly inserted and placed then follow the procedure e Turn on the dashboard key ON and verify that the YELLOW L
Download Pdf Manuals
Related Search