V100 GNSS RTK System Getting Started - Geo
Contents
1. 63 Schedule2 Key accessories information ee eeee eee eee e ee eene 64 VI HITARGET Product Introduction CHAPTER Product Introduction This chapter describes Hardware structure Power supply system Button operation LED Handheld controller 1Hand20 HITARGET Product Introduction 1 1 Hardware structure The product appearance is divided into three parts upper cover bottom cover and control panel Figure 1 1 1 Y Raised point Figure 1 1 2 HI TARGET V100 GNSS RTK System Getting Started Five pin socket Battery compartment Mini USB socket Protective plug Connection screw Figure 1 1 3 Connection screw for the instrument fixed to the base or the pole Battery compartment for housing lithium battery Five pin socket for external data linking and external power supply Mini USB socket for connection to the host and external devices upgrade firmware and download the static data can also charge or supply electricity to the host Protective plug for dustproof and waterproof Notice If it 1s unnecessary to use five pin socket and USB interface please cover the rubber plug to prevent dust HI gt TARGET Product Introduction 1 2 Power supply system Battery adapter type Name type lithium battery BLP 6300S Power adapter PSAIIOR 050Q Lithium battery HITARGET Figure 1 2 1 Adapter Figure 1 2 2 Recharge V1002. Work Mode an Firmware Version GPS Board Others Expiration Configure Manufacturer Hi Target Console o Type Bluetooth a ku qua m ie A Register connect Bluetooth ls Bluetooth pairing request Bluetooth The paired devices To pair with Type the device s required PIN Usually 0000 or 1234 PIN contains letters or symbols You may also need to type this PIN on the other device Cancel Q Search device 5 Search device 7 When connect to a new receiver 6 Or select the receiver from the list PIN is needed directly 8 Enter 1234 press OK HI TARGET 4 Rover setting m O HPC Others External Device Console Q Data Collector Internet Project Survey 1 Slip to Device tab 3 Press 3 to set Data link 2 Press Rover 4 Select Data Collector Internet mode WAAS Set Rover Mode Datalink Data Collector Internet Parameter O LU The SIM card is not inserted or the SIM card is temporarily unavailable Press here 172 16 21 42 CORS dadana nikah Port 1032 ZHD Configure Other HI TARGET V100 GNSS RTK System Getting Started 5 Make sure your controller has SIM 6 Press to select communication cards installed mode Select the right APN option 7 Select CORS Set Rover Message Type RTCM 3 2 172 16 21 42 9 ype 3 2 Diff Port B Source Node RTCM32 audrate D OBERE TECTUM gt Elevation
3. Road Design Cross section Earthwork Points Calculation Project Device You can add stake point by 4 Enter the point name then search it from list Input the coordinates manually and save the point to the list by ticking the option Select from list Map picking Press OK to confirm and start staking out Save to Stake Pts Lib 50 HI TARGET V100 GNSS RTK System Getting Started Stake interface KOMA 7 Backward Southward Stake Points Config Towards the Right A 00 00 O None y d B 2 0 0 0 ws 55 Eastward Delta H Altitude difference between stake coordinate and actual position Name Name of stake point o Relative precision HD Horizontal Distance 51 HITARGET Work modes Introduction 3 Line staking 1 Stake line from line library Stake Line Config Mapping Stake Road Store Cross Survey section kad Road Design Cross section Earthwork Points Calculation a Q Project Device 1 Press Stake Line 2 Press 2 to expand the list 3 Press 3 to add the line from library Notice You can define the line to be staked out manually or import it from files Please refer to the manual of Hi Survey software to get the procedures 52 HI TARGET 3 2 4 Data Export V100 GNSS RTK System Getting Started Data achievement export supports the following format txt CSV dxf shp File shp and Excel File csv Qe Single
4. section pn py basee N Cross section Earthwork Points Calculation AN NN Project Device aul 1 Slip to Survey tab 2 Press 2 to expand the list Press Detail Survey 43 HITARGET Work modes Introduction 1 Single point collection single point collection means collecting the data of each point by manual operation Y Baas T EO WE Text Detail Survey Config Save Point gt 7 Py 07 27 RTKInt 3 0 2 0 D 48 Name pt Target H 1 8 6 Pole Desc O Station 0 0000 y base8 Status RTK Int N 2567355 2308 E 1360114 5276 Z 35 4187 A B 22 59 00 64262N 0 0 0040 L 113 22 03 49686E 0 0 0060 H 35 4187 0 0 0200 Time 2015 04 28 11 23 49 1 Press D or the same button on 2 Press 2 to select the height type physical keyboard to collect then input the value The information of point including point name target height the first point needs to be measured and this value will be set as the default to the next points and point position description non input optional Click OK to complete the collection of the point 44 HI TARGET 2 Average collection V100 GNSS RTK System Getting Started That is averaging for the multi measurement value of coordinate for each point 5 07 27 d RTKInt v 30 2 0 d 48 N 22752971 6860 E 17634471 0829 Z 26 7912 Name N 22752971 6860 22752971 6860 22752971 6860 22752971 6860 22752971 6860 22752971 6
5. D Plane 2 5 mm 1x10 6D Static rapid static Height 5 mm 1x10 6D accuracy Code difference 0 4m SBAS difference 1 2m Initialization reliability gt 99 9 System configuration Operation system intelligent real time system Boot time Is Data storage built in 8GB storage Built in communication e NEC near field communication e Dual mode Bluetooth communication 20 HI TARGET V100 GNSS RTK System Getting Started Control panel Panel one button Indicator three bi color LED lights External interface e USB socket five pin socket Electric characteristics Battery high capacity lithium 6300mAh 3 7V removable continuously operating time reaches above 7 hours Voltage USB interface DC 4 2 5 5V 1 5A five pin interface DC6 28V 1A Power consumption 3 2W Physical characteristics Core control chip CotexAS built in 16GB Flash memory e Size 127 5mmx57mm Weight lt 700g including battery e Material magnesium alloy 21 HI TARGET Technical parameters Environment characteristics Protection class IP67 protect 2m temporary soaking underwater completely prevent dust Shock proof Anti 2 m natural fall Working temperature 40 C 65 C Storage temperature 40 C 75 C e Relative humidity 100 anti condensation Private cloud service The cloud service supports for 24 hours realizes integrated technique of indoor work and f
6. because it is related to the accuracy of coordinate There are two methods to set the coordinate system 30 HI TARGET V100 GNSS RTK System Getting Started WAAS n 47 0 Coord Params of ae N Currant 4p OA G2 Project Info Project Projection mE Settings Projection m Note A project can have only one TruckPoint A i MZ sa TruckPoint Parameters Points TruckPoint Info RegulatePoint Mapping Data Data Transfer File Transfer RegulatePoint Info gp Device Survey Data Management 1 Click Project Settings Including 2 Settings interface settings of project and coordinate system information 31 HITARGET Work modes Introduction 1 Build a coordinate system Parameters Coord Params of a Predefined List Diirrant m Unnamed Projection WGS84 Note A project can have only one TruckPoint UTM Kertau Zone 47N TruckPoint Malaysia Bong TruckPoint Info testdamfile China 2000 Zone3 30 RegulatePoint China 2000 Zone3 25 RegulatePoint Info Belgium Belge Lambert Belge 1972 new Data Management Predefined User Defined 1 Click D to enter into the setting 2 Select a coordinate system from interface Predefined or build by User Defined Notice Any question about User Defined pleases contact technical support 2 Add existing coordinate system files 32 HI TARGET V100 GNSS RTK System Getting Started Select dam File Coord Params of zh i p s
7. detect the voltage of lithium battery and external power supply and choose the higher voltage power As for external power supply it shall use the special power specified by Hi Target Notice 1 The service time of lithium battery will decrease along with the decrease in temperature and charging discharging times increasing A new 6300mAh lithium battery can be used for 7 hours of static data collection or rove work 2 Please charge the battery within 24 hours after using up to extend the service life of battery or the battery performance will be damaged 3 If the battery won t be used for long times please charge once every month to extend the service life of battery HITARGET Product Introduction 1 3 Button operation Most settings and operations of receiver are completed using a button on control panel Power button Figure 1 3 1 Description of power button operation Operation name Description On Shutdown status long press the button one second to boot all lights are on Off Boot status long press the button three seconds all lights double fast flash release the button Shutdown status long press the button six seconds Automatic setting station all lights double fast flash release the button the instrument will automatically set the base station Double click the button to switch working mode Operating mode switching double click each time to switch between static and RTK mode TF Clic
8. iHand20 Front of handheld controller The front of 1Hand20 handheld controller includes touch screen keyboard and microphone Touch screen AI TARGET Keyboard Microphone Figure 1 5 1 Touch screen Multipoint capacitive touch screen with touch pen which supports Chinese and English input Keyboard Photograph direction control switch between Chinese and English data collection volume control power on power off and other functions 11 HITARGET Product Introduction Microphone Internal microphone can be used for field collection of voice message Reverse side of handheld controller There are camera battery cover belt trumpet etc on the reverse side of 1Hand20 handheld controller Camera Speaker Battery cover NFC module Belt Figure 1 5 2 Camera Used for field collection of image information Battery cover Internal removable lithium battery 12 HITARGET V100 GNSS RTK System Getting Started Belt Connect the belt to prevent sliding down Speaker Conduct real time voice broadcast for the instrument operation and status Side of handheld controller Waterproof amp dustproof rubber cover Audio port Mini USB Figure 1 5 3 Mini USB Used for connecting USB data line and 1Hand20 handheld controller Audio port Used for connecting headphone cable and 1Hand20 handheld controller Warnings In case of not using audio port o
9. lithium battery should be charged by PSAIIOR 050Q adapter about 7 hours of charging time 4 HITARGET V100 GNSS RTK System Getting Started Warning 1 Only the battery and charger configured by the manufacturer can be used the battery must not be thrown into fire or used in metal short circuit electrode 2 Stop using when the battery is heating deformation liquid leakage smelling or other abnormal reactions please exchange new battery 3 Stop using when the battery s working time has been significantly reduced the battery 1s aged please exchange new battery Battery installation and removal 1 Push up the battery cover button open battery cover Battery cover button Figure 1 2 3 2 Align battery pole with battery compartment pole push the battery to the end and the mental button will upspring HI TARGET Product Introduction Metal button Battery pole HITARGET Figure 1 2 4 Figure 1 2 5 3 Close the battery cover Removal Push up the battery cover button to open it then press the metal button and remove battery HI TARGET V100 GNSS RTK System Getting Started Power supply Power supply Power supply mode Internal lithium battery Power supply mode External USB Five pin socket External power supply USB socket DC power 4 2 5 5V 1 5A request Five pin socket DC power 6 28V 1A When external power supply the host will automatically
10. to turn off turn on the screen backlight APP Quick start of Hi Survey software press button APP for a long time for the Road popup then select Hi Survey Road and click Ok And the software selected this time can be started quickly only by pressing button APP next time Cautions When installing Hi Survey Road for the first time it is necessary to press button APP for 3s for software quick start selection settings Otherwise corresponding software cannot be started quickly by only pressing button APP 16 HI TARGET V100 GNSS RTK System Getting Started P oim A 1 Bs Software selection Software selection P Figure 1 5 9 Fn button Press Fn button for 3s and popup interface of software switching so as to achieve fast switch of input method In case of physical button input method only press Fn button to switch over input methods of Chinese Pinyin strokes digitals and letters under input status Collect button Collect data by manual operation Camera button Press it for a short time to enter into photograph interface Press it for 3s on the non camera interface to start up shut down flashlight function Screenshot Press VOL and power button simultaneously for 3s screen capture will be kept in the file of Mobile phone storage Pictures Screenshots Cautions 1 When the iHand20 handheld controller is not used in the work please turn off the backlight for saving electric quantity and prolonging t
11. 00 kama Project Info Project Settings Parameters Points Device Survey 1 Press Data Transfer Projection Raw Data File Transfer Stake Point Control Point Exchange Types 9 Export Import Directory storage sdcard0 ZHD Out E m 12011 ce File csv 2 Press 2 to select data type 3 Press 3 to select exchange type 4 Choose the path to output 5 Name the file 6 Select the format Press OK to confirm 53 HITARGET Work modes Introduction 3 2 5 Auto backup and quickly recover Project is auto restored in Hi Survey External SD card is used for important data backup Including Raw data project file coordinate system or encryption code file zl amp Current Project Project Info Projection Name demo Points 4 ag Projection Lithuania LKS94 d Time 2015 11 2011 08 36 Parameters Available SD 1 55G Repeat PtName Support Mapping Data Data Transfer File Transfer t seven chau demo test P e M N M demo x Device Survey 1 Press Data Transfer 2 Press to enter into project recovery configuration interface 54 HI TARGET V100 GNSS RTK System Getting Started 3 Turn on the Auto backup Recovery Project Data 4 Select the project to be Data backup directory storage sdcard o List recovered from the list t 5 Press Start Recovery Unnamed Notice OERULUTM The path of backup f
12. 16 9575 1360114 6789 1360114 6879 1360114 5222 1360114 5287 1360114 5276 displayed in this interface 47 Q Search Set All the collected points will be HITARGET Work modes Introduction 3 2 3 Stake out 1 Import the stake point 1 Add the point manually E 5 SES A vy Een Qe Single 0 0 i ge kane Project Info Project Projection Settings MEINE Parameters i Raw Data Mapping Data Data Transfer File Transfer n Device Survey Q Search Os Add tk Set 1 Press 1 to add the point 2 Press 2 to add point to the list manually 48 HI TARGET V100 GNSS RTK System Getting Started You can add stake point by 3 Enter manually 4 Get from receiver 5 Select from list 6 Map picking Press OK to confirm Desc x Cancel 2 Import the points lines from file Support Dxf file to be staked Exchange Types Export 9 import Project Info Project l Settings Directory storage sdcard0 ZHD Out i m t s se 2010_stup 2007_stup 2004_stup ava dubra ava_dubra ava_dubra Parameters Points 10_stupav a_dubravy File Transfer All Device Survey 1 Press D to import the points 2 Slip to Stake Point from file 3 Select mport 4 Choose the file you uploaded 49 HITARGET Work modes Introduction 2 Point Staking Stake Points Config 00 27 RTD v ao A T uy 4 Mapping Stake Road Store Cross Survey section a kad
13. 860 0 0 0000 0 0 0000 0 0 0000 E gt 17634471 0829 17634471 0829 17634471 0829 17634471 0829 17634471 0829 A FixPos 1763278 0829 Crm 1 Press 1 to collect 2 Press OK to save the point 3 Press here to change the configuration 3 Automatic collection Point measurement will be recorded automatically according to the configured record condition 45 HITARGET Work modes Introduction AO A w T7 Text Detail Survey Config 5 07 27 4 RTKInt Y 3 0 T 0 5 48 Prefix pt FixP Axo 1 Press 1 to start automatic 2 Select the mode and enter the collection interval 3 Press OK to start collecting Y Detail Survey Config i e D t9 00 30 A FixPos T C7 i5 A 0 0 21 N 22752988 6306 0 0 0000 E 17634453 5128 0 0 0000 Z 32 9692 0 0 0000 1 44 cm 4 All the points will be auto saved Press here to end collecting 46 HI TARGET 4 View all collected points Project Info Parameters Project Settings Projection Mapping Data Data Transfer File Transfer Q i Device Survey 1 Press D to view all collected points Press 2 to manage the raw data V100 GNSS RTK System Getting Started F Stake Control Name 4 N E ptt pt pt6 pt5 pt4 pt3 pt2 pt1 dL CQ E ww aJ dL Tid 25b 355 2376 2567355 2266 2567354 1453 2567355 1295 2567354 9076 2567355 2386 2967355 2394 2967355 2378 ee 1360114 5285 1360114 5233 13601
14. ARGET V100 GNSS RTK System Getting Started 4 1 Registration procedure Register ihand20 step I Run the Auth Code App which icon is like a lock You can find it on the desktop or the Apps Listing iHand 20 amp device 11440643 mo active time 2015 07 03 a idi e pan F lt a Please enter valid code Camera Gallery Hi SUrVey Figure 4 1 1 Step 2 Enter the registration code in the input box then click submit Step 3 Registration should be successful If failed please check the code and try more times Register GNSS receiver via Hi Survey App Step 1 Power on your GNSS receiver then run the Hi Survey App and click the Device 1con 59 HITARGET Trouble Shooting Survey Figure 4 1 3 Step 2 Connect your GNSS receiver first and then click the Register 1con Input the 24 bit registration code press OK step5 Device Register Singl a EM o 11800021 Work Mode Rover Mode Firmware Version 1 0 V100 Receiver GPS Board 4 93 Expiration 2015 12 22 Configure Manufacturer Hi Target Type Bluetooth A Register X Disconnect Figure 4 1 4 Step 3 Registration should be successful If failed please check the code and try more times 60 HI TARGET V100 GNSS RTK System Getting Started 4 2 Firmware upgrade The receiver can upload data like U disk it need Mini USB data cable one end of Mini USB data cable is connected to computer USB p
15. D20150010B Hi Target Surveying _ 64
16. V100 GNSS RTK System Getting Started HI TARGET Hi Target Surveying Instrument Co Ltd All Rights Reserved Manual Revision File number u Revision en Revision Date Description Level 2015 11 30 V100 GNSS RTK System User Manual HI TARGET V100 GNSS RTK System Getting Started Preface Introduction Welcome to use Hi target V100 receiver this introduction is applicable to Hi Target V100 products The introduction describes how to install set and use V100 products Experience Requirement In order to help you use Hi Target series products better Hi Target suggests you carefully reading the instruction If you are unfamiliar with V 100 products please refer to www hi target com cn Tips for safe use Notice The contents here generally are special operations needing your special attention Please read the contents carefully Warning The contents here generally are very important Such wrong operation may make the machine damaged make the data lost even breaks down the system and endangers personal safety HITARGET Profe Exclusions Before using the products please carefully read the operating instruction and it will help you better use the product Hi Target Surveying Instrument Co Ltd will not assume the responsibilities if you fail to operate the product according to the requirements in operating instruction or operate the product wrongly because of failing to understand the operating
17. an collect static data Relative operations are as below 1 Set up receiver on a control point centering and leveling strictly 2 Measure the height of receiver for three times on condition that the difference of each measuring 1s less than 3mm and the final height of the receiver should be the average height Below is the schematic Measurement reference bench Height measurement point 130mm Figure 3 1 HITARGET Work modes Introduction Notice 1 Instrument height should be measured from control point to the height measurement point of the measurement reference bench 2 The measurement reference bench radius 1s 0 130 meter 3 Record point name receiver S N receiver height beginning time 4 Press power button to power on and double click power button to set static collecting mode Notice The satellite LED flashing means the receiver is searching the satellites The satellites are fixed once the satellite LED stays light on Network LED flashes due to your collection interval set which means an epoch will be collected every flash 5 Turn off the receiver after static data collected and record the turn off time 6 Download and post process static data Caution 1 Don t move the tri branch or change the collecting set while the receiver 1s collecting data 2 V100 GNSS receiver doesn t support recording Rinex format data 26 HI TARGET V100 GNSS RTK System Getting Started 3 1 2 Stati
18. b 6 Password BD2 CH RTCM1021 RTCM1023 GLONASS GEL Configure Other Configure Datalink 8 Enter the IP amp Port value got from 12 Select the Message Type same as the CORS operator the node you selected 9 Press Set to get and select mount points nodes 13 Set the needed Elevation 10 Enter the username amp password 11 Tick RTCM1021 RTCM 1023 if your CORS service operator provides this type of message Press Set to finish setting 37 HITARGET Work modes Introduction 5 Floating box Semester tories tie Satellites Tracked Satellites _ E 30 RTKInt 5 1 0 E Ex eceiver power Ex Coreen Er ull Figure 3 5 Solution state It is mainly divided into the following several modes except for fixed coordinate precision is arranged from high level to low level The given point refers to fixed coordinate Base RTK fixed solution RTK float solution RTD solution single point positioning no solution type indicates no GNSS data Correction latency Refers to calculating time after Rover receives the signal from Base PDOP value Intensity factor of space geometry where the satellite 1s distributed Generally the better the satellite distribution 1s the smaller the PDOP value is Generally the value is less than 3 as the more ideal state Number of visible satellites Number of satellite received by receiver at least 5 satellites required by RTK work Number of pu
19. blic satellites Base hasn t it and only Rover has it after receiving the difference data It refers to the satellite used for calculation when the Base and Rover participate in the searching of ambiguity of whole cycles at 38 HITARGET V100 GNSS RTK System Getting Started the same time which are generally more than 5 so as to ensure normal work Click the satellite icon in the floating window to rapidly check detailed information of current connected receiver satellite 1 Position information s Coo To sia Figure 3 6 Press here to display position information of current point including position speed solution state and time etc RTK Int Diff Age 2 0 RTK Int Diff Age 2 0 A F os Base Coord I OUII4 0Z242 Z 34 4227 B 22 59 00 64280N L 113 22 03 49682E HRMS 0 0042 H 36 5135 VRMS 0 0100 Azi 216 31 46 46998 Velocity 0 09718 UTC 2015 04 28 11 12 56 Baseline 2 0948 Length Azimuth 113 22 47 20560 Reset RTK Reset Antenna Connect Net Disconnect Net Base Station Location Info 39 HITARGET Work modes Introduction 2 Stellar map a 28 30 4 RTKIn 13 1 0 Figure 3 7 E 51 Distribution situation of projection position of satellite can be viewed by pressing here Roundness refers to GPS satellite and SBAS satellite square refers to GLONASS and BDS satellite GPS Prn value is 1 32 GLONASS Prn value is 65 96 BDS Prn value is 161 197 mm View elevatio
20. c data storage and download Collected GNSS static data 1s stored 1n static disk that SGB internal storage of V 100 receiver effective storage space is 6 6GB includes two folders log and gnss log folder stores log information the data format storage in gnss folder is gns You can connect the receiver to computer through USB data cable copy static data to your computer like using a U disk Figure 3 2 Notice N When the receiver storage space is less than 10MB data light red fast flash and it stop recording data the existing data files will not be overwritten The receiver can download data like U disk it need Mini USB data cable one end of Mini USB data cable is connected to computer USB port and the other end is connected to Mini USB port of receiver It will appear static disk after being connected then 27 HITARGET Work modes Introduction open the disk copy the collected static files to computer s hard disk UPDATE H Figure 3 3 The steps of modify point name and antenna height of downloaded static file are 1 Choose GNS files and double click the mouse 2 Modify point name and input antenna height in the popping up dialogue of file edit and then click OK E File Editor Marker Name T less than 4 charactors Antenna Slant Height 2 0000 m Figure 3 4 Caution N It only supports copy procedure when connected to computer Deleting static files and formatt
21. he working time 2 Only the image collection interface supports the shortcuts operation In order to avoid the input conflict of input box the 17 HITARGET Product Introduction text interface does not support shortcuts operation 1 Average collection shortcut is Button 7 2 Indirect measurement shortcut is Button 8 Data download 1 Connect handheld controller to computer by USB data line and pull down the notice column and click USB computer connection open USB storage 2 If it is required to synchronously operate handheld controller or install and use third party software to debug data on the computer USB debugging function shall be ticked Turn on the handheld controller and click System Settings Developer options USB debugging on the desktop menu 3 In the popup debugging window click OK to complete the connection between handheld controller and computer 4 In the computer file operations between handheld controller and computer can be conducted by Portable Devices 18 HI TARGET V100 GNSS RTK System Getting Started CHAPTER Technical parameters 19 HITARGET Technical parameters GNSS configuration Table 1 GNSS configuration International first class PCC new efficient intelligent System core real time core DS PS B1 B2 Channel ASC II NMEA 0183 and binary Trimble GSOF RTK positioning Plane 8mm 1x 10 D accuracy Height 15 mm 1x 10
22. ield work remote manage serve and support equipment It manages team project shares parameters and control points post backs real time verify and note track of result data by cloud background After the user s authorization terminal servers can remotely provide customers with technical support including system version upgrading system registration remote debugging and other services Environmental Requirements The receiver shall operate in dry working environment regardless 22 HI TARGET V100 GNSS RTK System Getting Started of waterproof materials In order to advance the stability and service cycle of receiver the receiver shall be prevented from extreme environment such as Moisture Temperatures above 65 degrees centigrade e Below 40 degrees centigrade Corrosive liquids or gases Electronic Jamming The receiver shall not be installed in the place near to strong electric power and interference signal such as Oil duct spark plugs e Television and computer display Generator Battery operated motor cycle DC AC power supply changeover equipment Fluorescent lamp Power supple 23 HITARGET Work modes Introduction CHAPTER Work Modes Introduction This chapter describes B Static Mode B Network Rover Mode B Base Mode with External Radio 24 HITARGET V100 GNSS RTK System Getting Started 3 1 Static Mode 3 1 1 Static data collection V100 GNSS Receiver c
23. ile External SD card ZHD Bak Project Road Notice 1 External SD card is necessary before users backup project file 2 All the backup operations are over version 1 0 2 55 HITARGET Work modes Introduction 3 3 Base Mode with External Radio When connected with an external radio V100 GNSS receiver can also work as a GNSS base Set Base Antenna Device Antenna V100 GNSS Antenna iQ B arget H 2 0000 Demo HPC Others Pole Vertical Slant Ground Point 9 7 9 c Name X B111914 Console 22 59 00 76703N T Configur Datalink Other 1 Connect to V100 GNSS receiver 2 Select the height type and input then press Base the Target Height 3 Set the coordinates of base by 3 Input manually 4 Smooth from receiver Select from point library 56 HITARGET V100 GNSS RTK System Getting Started Diff Mode Message Type RTCM 3 2 Diff Port Baudrate Q Data Collector Internet Bn CH Configur Receiver Datalink 6 Set Datalink 7 Select the correction message Select External Device type 8 Set the Elevation angle Press Set to confirm Notice For the details of Radio which is supported and how to configure the connection please refer to the related documents on Hi Target website www hi target com cn 57 HI TARGET Trouble Shooting This chapter describes B Registration procedure B Firmware upgrade B Reset operation 58 Trouble Shooting CHAPTER HIT
24. ing disk can be only operated by handheld software 28 HI TARGET V100 GNSS RTK System Getting Started 3 2 Network Rover Mode Pair with the powerful surveying software Hi Survey the intelligent VIOO GNSS receiver will turn into a portable network rover The main operating procedures in brief B Project setting B Data collecting B Staking out B Data exporting 3 2 1 Project setting lt New project lt Project settings lt Device connecting lt Rove setting 1 New project After new project is built before the measurement the collected data 29 HITARGET Work modes Introduction will be saved in the project When building new project relevant setting needs to be conducted for example setting of project information and coordinate system etc eor Recov Project Info amp Current Project Project Projection Name demo Settings l Points 2 Projection WGS84 Time 2015 11 16 15 33 59 Parameters Points Available SD 1 58G Repeat PtName Support History Mapping Data Data Transfer File Transfe t t seven chau demo test A ee oo Device Survey 1 New project can be built and the 2 Input project name existing project can be opened or Note The name of new project deleted shall not be the same as the name of old projects 2 Project settings Project settings include coordinate system and other parameters settings For measurement coordinate system must be configured
25. instruction Hi Target is committed to constantly perfect product functions and performance improve service quality and reserve the rights to change the contents in operating instruction without separate notice We have checked the consistency between contents in instruction and software amp hardware without eliminating the possibility of deviation The pictures in operating instruction are only used for reference In case of inconformity with products the products shall prevail IV HI TARGET V100 GNSS RTK System Getting Started Technology and Service If you have any technical issues you can call Hi Target technology department for help we will answer your question in time Relevant Information You can get this introduction in the following ways 1 After purchasing hi target V100 receiver there will be V100 GNSS RTK System User Manual in the instrument container to guide you how to operate instrument 2 Log in hi target official website download the electronic version introduction in Download Center Manual Surveying Products Advice If you have any advice or suggestion on V100 please call us or Dial the national hotline 86 400 678 6690 Your feedback information will improve the production quality Content Content CACO T NA NANANG E III unir m M VI Product EBLEOQUHCEIOTE osaera E E S 1 1 1 Hardware structu
26. k power button power LED flashing times Status inquiry displays power Boot status long press the button more than 6 Reset motherboard seconds all lights flash at the same time release the button it will reset motherboard HITARGET V100 GNSS RTK System Getting Started 1 4 LED In different setting mode it displays the different LED status Network LED Satellite LED Power LED Figure 1 4 1 LED Function Description LED Meaning Power LED Conin Full battery Green IEEE power ya Long term Full battery voltage internal battery gt 3 9V 100 Yellow lighting power Long term fies 990 ihing Normal voltage 6 internal battery power lt 99 Slow flash Low voltage internal battery lt 5 Power indication 1 4 flash per minute under the Power LED direction of electricity Red 026 2596 Fast flash 25 50 1 2 3 5076 7576 4 75926 10026 Long term Green eats RTK mode HI gt TARGET Product Introduction 1 RTK mode flash as difference data interval Network LED Slow flash 2 Static mode flash as sampling interval Red Static mode storage space lt l1OMB Long term Satellite LED ug Satellite lock lighting Green Slow flash satellites are lost Satellite LED Network LED Power LED all fast Three LEDs Fast flash flash at the same time when release power button the motherboard will be reset 10 HI TARGET V100 GNSS RTK System Getting Started 1 5 Handheld controller
27. n cut off 2f 1 8 angle of GNSS satellite and click Set to set the elevation cutoff angle of receiving satellite v PME Bers go qoos 10 8 Status SAT Info 40 HITARGET V100 GNSS RTK System Getting Started PDOP Elevation Click Status and give Se the color according to L1 carrier signal to noise ratio of satellite Orange lt 15 yellow lt 35 green gt 35As shown in the 12 14 18 22 25 26 31 32 65 66 67 fh T following figure SATView SAT Info 3 Signal to noise ratio figure of satellite Prn refers to number of satellite Azi refers to azimuth angle of satellite Ele refers to satellite elevation L1 refers to signal to noise ratio of L1 and L2 refers to signal to noise ratio of L2 41 HITARGET Work modes Introduction Sats PDOP Elevation Click SAT Info and Prn 28 1 9 19 refers to number of n 12 40 24 Y signal to noise ratio of 18 L1 L2 refers to signal to 22 noise ratio of L2 25 26 31 SATView Status 42 HI TARGET V100 GNSS RTK System Getting Started 3 2 2 Data collection Single point mode lt Average mode lt Automatic mode After the settings for the above project and Base as well as Rover being completed successfully enter into data collection interface for collection Corresponding collection methods can be selected according to different demands 5 07 26 RTKInt 7 a T Te 48 Stake Road Store Cross
28. ort and the other end is connected to Mini USB port of receiver It will appear UPDATE disk after being connected then open the disk copy the firmware files to it Remove it and disconnect USB cable restart GNSS receiver The receiver will upgrade the firmware automatically The new firmware can be downloaded from www hi target com cn STATIC G Figure 4 2 1 61 HITARGET Trouble Shooting 4 3 Reset operation When the Bluetooth is not connected satellite searching fails and network connection fails the operation can be conducted in case that instrument restarting does not work Reset receiver In power on status long press power button gt 6s when LED begins flashing release power button to reset and then restart the receiver 62 HI TARGET V100 GNSS RTK System Getting Started Schedulel factory default parameters Table 2 Factory default parameters Options content The factory default parameters System Working mode Rover parameters Data link Data collector internet Differential mode RTK Correction format RTCM 3 2 Elevation angle 10 GPS Enable BDS Enable GLONASS Enable Static collection interval 5s Static elevation angle 10 Others none 63 HI TARGET Appendix Schedule2 key accessories information Table 3 key accessories information name version manufacturer Main performance index Motherboard 220channels Antenna Small measuring Hi Target Surveying 51dB Databoard ZH
29. r Mini USB please close the rubber cover so as to be waterproof and dustproof 13 HITARGET Product Introduction Handheld controller accessories Charger Figure 1 5 4 Battery Lithium battery 3 7V 6300mAh HI gt PTARGET Figure 1 5 5 Data line Figure 1 5 6 Connect to the USB port of computer and used for download of data Connect to the USB port of charger and used for charging 14 HI TARGET V100 GNSS RTK System Getting Started handheld controller gt ai Figure 1 5 7 Touch pen In case of using touch pen to operate the handheld controller it is required to start the function of handwriting pen and open the handheld controller s system setting auxiliary function check handwriting pen Operation of handheld controller Keyboard Most settings and operations of Hi Target iHand20 handheld controller can be completed by the touch pen and commonly used operations can be completed by Keyboard Appearance and functions of Keyboard are introduced briefly as follows 15 HITARGET Product Introduction Home Menu APP Collect Fn OK Space Enter Shift Camera Power Figure 1 5 8 Keyboard include Back OK Power APP Fn Collect Camera etc on button board of 1Hand20 Back Delete or exit the operation of current window OK Confirmation Power Press it for above 3s for power on power off Under the power on status press power button for 1s
30. re 2 0 0 0 cccccccccccccsssssseeeeeeeeceeaeeeseeeeeeeeeenaas 2 1 2 Power supply System ccccccccccceccesseeccceceeeeeeceessaeeseees 4 1 3 Button operation seeeeeeeeeeeananenenenanana anana nenen anna 8 FT 0 9 1 5 Handheld controller iHand20 11 Technical parameters cce eie sapa a aana a a BE Wa D ING TEN EDANE WE KN GENE ADA Na Ya KUD EH GENTONG Kak 19 Work Modes Introduction s oce aan Ha HEREIN NA INA DEDE NUNGGANG INGGA EINE EP QUU PEU 24 IL Slane Molt S 25 3 1 1 SILAT ACOE O e N 25 GAWA Static data storage and download 27 3 2 Network Rover Mode eeeeeere 20 Dadak PEOIGCDSe HII D ooo em a aka a E I A ere aa aaa ana TUE 29 689 902 TAA SONGGON oett IE vero IEEE 43 Du ANGADU M E 48 3 2 4 D EO e e A E aa Ag aaa anaa 53 0 298 Auto backup and quickly recover ssssse 54 3 3 Base Mode with External Radio 56 TFOUDICSBOOUHS oo oiii II Ir AA AANE A 58 4 1 Registration procedure eeeeeeeeeeeeeeee 50 4 3 Firmware upgrade ssseessssseeeeeeermmenns 61 4 3 ROSOLODOEOUIOBR ooi canted oU PMII EDEN HEPIMIUMM MEE 62 Schedulel factory default parameters
31. torage sdcard0 ZHD GeoPath1 DMiirrant Projection t 3 BJ54 dam China 200 Note A project can have only one TruckPoint 0 Zone3 TruckPoint 0 F China 200 WGS84 da UTM 0 Zone3 2 m WGS84 TruckPoint Info China 200 UTM UTM RegulatePoint 0 Zone3 Provisiona Provisiona RegulatePoint Info Belgium Ralna 1 Click D to add an existing datum 2 Select a datum system file be system file imported before Notice The dam file can be built with HGO post processing software or be output by User Defined Copy it to the Geopath folder then it can be loaded by software 3 Device connecting NFC Near Field Communication NFC is used to quickly establish Bluetooth connection On condition that the handheld controller or smart phone supports NFC function 33 HITARGET Work modes Introduction The application of NFC combined with new intelligent handheld a light touch will realize automatically connecting to receiver and run the software through Bluetooth Compared to the past complicated connection process V100 GNSS receiver is more convenient and efficient A APPKEY NFC Software selection d d 1 Long press APP button on 3 Take ihand20 NFC response area keyboard Press NFC select close to receiver s NFC response Hi Survey Road area 2 Press OK Bluetooth connection The receiver can also be connected by Bluetooth manually 34 HI TARGET 5 10pm Device
Download Pdf Manuals
Related Search