ViridianX5LGen2Manua.. - Viridian Green Laser Sights
Contents
1. 3 Always practice safe firearms handling techniques when handling a firearm with or without the Viridian 4 Never point a firearm with or without the Viridian attached at anything or anyone that you do not intend to shoot 5 Once the Viridian is attached to a firearm the firearm will be pointed at anything to which the Viridian is directed Do not point the Viridian at anything or anyone that you do not intend to shoot 6 The activation buttons on the Viridian allow you to operate the laser without placing your finger inside the trigger guard Always keep your fingers off the trigger and outside the trigger guard until you are ready to fire the weapon 7 Always verify that the chamber of the weapon is empty or clear before attempting to mount or dismount the Viridian Follow the clearing procedures as set forth in the manual for your firearm SAFETY SUMMARY VIRIDIAN WARNING LABEL Output Power lt 5 mW C DANGER gt Wavelength 532nm Class llla Laser Product LASER RADIATION AVOID DIRECT EYE MAX OUTPUT lt 5MW WAVELENGTH 532nm Z CLASS Illa LASER PRODUCTS BUILT IN THE USA SAFETY SUMMARY CONT DO NOT stare into the green laser beam DO NOT look into the green laser beam through binoculars or telescopes DO NOT point the green laser beam at mirror like surfaces DO NOT shine the green laser beam Into or near anyone s eyes DO NOT point the green laser a2. Congratulations on your purchase of a Viridian the finest and most visible laser sight available Please read and follow the instructions in this manual to get the most out of your Viridian Green Laser Sight YOUR PACKAGE INCLUDES 1 Viridian Green Laser Sight 2 Windage Elevation Adj Hex Wrenches Smaller sized 1 CR123A Battery 3 Volt Lithium 1 Rail Set System 4 Rail Set Screws 3 8 inch 2 Rail Screw Removal Hex Wrenches Larger sized 2 Gun Mounting Screws 1 inch TABLE OF CONTENTS Warnings and Cautions Safety Summary Installing Battery Viridian Diagram Figure A Changing the Rail Set Mounting Dismounting Operation SMARTLASER Technology Operational Modes Table A Zeroing Procedures General Information Maintenance Warranty Service If you experience any problems with your product or are missing parts please contact us for assistance We want to help you SUPPORT VIRIDIANGREENLASER COM OR 1 800 990 9390 WARNINGS 1 Before handling any firearm with a Viridian read and understand the entire contents of your firearm manual provided as well as the Viridian manual especially the safety precautions and procedures for safe firearms handling 2 Failure to follow the correct safety precautions and safe firearms handling techniques outlined in your firearm and Viridian operator s manuals when handling a firearm with the Viridian can result in serious injury damage to property or death
3. TO SEE IF THE CHAMBER OF THE WEAPON IS EMPTY OR CLEAR BEFORE ATTEMPTING TO MOUNT OR DISMOUNT THE VIRIDIAN FOLLOW THE CLEARING PROCEDURES AS SET FORTH IN THE MANUAL FOR YOUR FIREARM BE SURE OF YOUR TARGET AND BACKGROUND BEFORE FIRING WHEN YOU SQUEEZE THE TRIGGER YOU MUST EXPECT THE PISTOL TO FIRE AND YOU MUST TAKE FULL RESPONSIBILITY FOR FIRING IT 1 Set up a target with a clearly visible aiming point 15 2 Mount the Viridian onto the weapon s accessory mounting rail see Mounting procedures 3 Turn ON the Viridian see Operation procedures CAUTION po NOT FORCE WINDAGE AND ELEVATION SCREWS BEYOND THEIR INTENDED TRAVEL 4 While aiming the pistol through the iron sights use one of the two provided adjustment wrenches smaller sized to adjust the visible green point of the Viridian Turn the windage and elevation wrench to superimpose the Viridian s aiming point over the weapon s iron sight aiming point 5 Aim and fire a three round shot group into the center of the target s aiming point 6 Compare the impact point of the shot group to where the Viridian s aiming point was on the target to ensure they line up 7 Make the necessary adjustments to the Viridian to ensure its aiming point and the shot group are aligned 8 Turn the unit OFF An alternative way to align the Viridian is to hold the green aiming point perfectly fixed to the center of the intended target and then adjust
4. YOUR FINGER AWAY FROM THE TRIGGER UNTIL YOU ARE READY TO FIRE DISMOUNTING 1 To dismount the Viridian from your weapon loosen and remove the Mounting Screw in a counterclockwise direction Store your Mounting Screw in a secure place such as your original Viridian packaging 2 Your Viridian is now ready to be removed from your handgun Slide the Viridian forward and away from the trigger guard to remove it from your weapon Slight loosening of both Rail Set Screws may ease removal of unit Always take great care to NEVER put your hand in front of the muzzle of your firearm WARNING ALWAYS MARE SURE THE WEAPON IS CLEAR AND ON SAFE BEFORE ATTEMPTING TO MOUNT OR DISMOUNT VIRIDIAN FROM YOUR WEAPON NEVER PUT YOUR HAND IN FRONT OF THE MUZZLE OF A FIREARM ALWAYS KEEP YOUR FINGER AWAY FROM THE TRIGGER UNTIL YOU ARE READY TO FIRE i OPERATION SMARTLASER TECHNOLOGY The Viridian X5L has unprecedented user programmability options never seen before in a commercially available weapon mounted device Your Viridian s activation is completely ambidextrous Simply press either right or left button to activate or deactivate your Viridian X5L in any of its modes Holding either button in for longer than 3 4 second will activate your Viridian in momentary mode In this case your Viridian will turn off upon release of the button In the event your Viridian is accidentally left on it will shut down in approximately 10 m
5. each Rail Set by pulling upward 3 Insert new Rail Set on each side of Viridian 4 Lightly tighten each Rail Set Screw premature tightening of Rail Set Screws may prevent Viridian installation onto rail of your firearm YOU ARE NOW READY TO INSTALL YOUR VIRIDIAN ONTO THE RAIL OF YOUR FIREARM Once your Viridian is properly mounted onto your firearm full tightening of Rail Set Screws will further ensure a rock solid hold DO NOT OVERTIGHTEN RAIL SET SCREWS DOING SO MAY RESULT IN STRIPPED RAIL SET SCREW HEAD MOUNTING 1 Align the grooves within the Rail Set of your Viridian with the grooves on the rail of your firearm and slide rearward until your Viridian reaches the front of your firearm s trigger guard 2 Due to multiple hole positions on the pre installed Rail Set one set of holes within the sides of the Rail Set should align with the cross slot of the accessory rail under your firearm It is OK to slide your Viridian slightly forward away from the trigger guard to achieve this alignment 3 Insert the Mounting Screw and turn it clockwise until firmly tightened A flat head screw driver or coin can be used here If possible install both mounting screws to ensure absolute tightness WARNING ALWAYS MAKE SURE THE WEAPON IS CLEAR AND ON SAFE BEFORE ATTEMPTING TO MOUNT OR DISMOUNT VIRIDIAN FROM YOUR WEAPON NEVER PUT YOUR HAND IN FRONT OF THE MUZZLE OF A FIREARM ALWAYS KEEP
6. to repair or replace at Laser Aiming System s option shall be the purchaser s sole and exclusive remedy under this warranty Warranty does not cover battery leakage contact battery manufacturer in this event This warranty extends only to the original owner For service or repair return unit UPS prepaid with a copy of the sales receipt to Laser Aiming Systems Corporation 20 NOTES SERVICE DO NOT RETURN THIS PRODUCT TO THE STORE For service or repair please call or email before returning unit Send to Viridian Green Laser Sights 5929 Baker Road Suite 440 Minnetonka MN 55345 ATTN Service Repairs GREEN LASER SIGHTS 1 800 990 9390 VIRIDIANGREENLASER COM Service OViridianGreenLaser com Fax 1 952 224 4097 X5L705 5 11 NOTES VIRIDIAN IS A REGISTERED TRADEMARK OF LASER AIMING SYSTEMS CORPORATION AND RAIL SET ARE TRADEMARKS OF LASER AIMING SYSTEMS CORPORATION ITIS TO ASCERTAIN AND OBEY ALL APPLICABLE LOCAL STATE FEDERAL AND INTERNATIQR SALE OF ANY ITEM MANUFACTURED OR SOLD BY LASER AIMING SYSTEMS CORPORA TO CHANGE WITHOUT NOTICE PRODUCTS MAY VARY FROM THOSE PICTURED 2011 LASER AIMING SYSTEMS CORPORATION i k D MSM EC NOLOGY VERSA LOK Ces OF THE BUYER NOT THE SELLER IN REGARD TO THE POSSESSION USE AND ATIONS ARE APPROXIMATE AND SUBJECT
7. windage and elevation so that your green aiming point is brought to the center of your previous shot grouping The gun and the Viridian must remain in a fixed position while making these adjustments WARNING never PUT Y0UR HAND IN FRONT OF THE MUZZLE OF A FIREARM ALWAYS KEEP YOUR FINGER AWAY FROM THE TRIGGER UNTIL YOU ARE READY TO FIRE ALWAYS MAKE SURE THE WEAPON IS CLEAR AND ON SAFE BEFORE MAKING WINDAGE ELEVATION ADJUSTMENTS GENERAL INFORMATION Separate modes allow for individual laser recognition in tactical team situations Constant beam mode will give you the maximum laser visibility however using one of the laser pulsing modes will maximize battery life Battery life with laser on only will increase from approx 7 hours in constant to 10 hours in the pulsing modes With laser and tactical light on high output battery life will be approximately 60 minutes Your Viridian green laser is equipped with APC circuitry This maintains constant laser power output for a consistently bright aiming point In the event of excess internal heat buildup you may temporarily experience reduced laser power output This is by design and will not damage your 17 laser This condition may be more prevalent with heavy use of the LED while the laser is on or in extremely hot environments MAINTENANCE Front Lens Cleaning Use a moistened cotton svvab to periodically clean the front lens of gun powder residue This step is im
8. inutes after a brief warning period If you wish to keep the power on simply press either button This will reset the power down timer The Viridian X5L has a total of 6 unique user modes See Table A To cycle through these modes simply press and release both right and left buttons at the same time while the unit is on For those that desire even more user programmed versatility hold down both buttons for 3 seconds to engage Deep Programming Mode This will allow customized frequencies of pulse rates of both light and laser as well as adjustable LED lumen output MODE LASER 1 Constant Constant Constant Pulse Pulse LIGHT Constant Strobe Constant Constant DEEP PROGRAMMING NA TABLE A X5L LIGHT DIMMER Starts at highest lumen steps down to medium then low then back to high each step is approx Y second LIGHT FREQUENCY OF STROBE Starts at an ideal 20Hz steadily proceeds upward until peak of 40Hz second pause jumps to bottom at 1Hz second pause then proceeds up to ideal 20Hz second pause and then repeats LASER FREQUENCY OF PULSE Starts at ideal 10Hz steadily proceeds upward until peak of 20Hz Y second pause jumps to bottom at 1Hz then proceeds up to ideal 10Hz second pause and then repeats LIGHT DIMMER Starts at highest lumen steps down to medium then low then back to high each step is approx Y second LIGHT DIMMER Starts at highest l
9. portant to prevent any degradation in the quality of the green aiming point and or beam Exterior Of Unit Clean the Viridian by wiping with a soft damp cloth Standard gun cleaning solvents may be used to clean stubborn areas Electrical Contacts For cleaning of all electrical contacts use a cotton swab dipped in alcohol To remove heavy build up on the contacts carefully rub with a standard pencil eraser be sure to thoroughly remove eraser residue WARNINGS AtWAYS CHECK TO SEE THAT THE CHAMBER OF THE WEAPON IS EMPTY OR CLEAR BEFORE ATTEMPTING TO MOUNT OR DISMOUNT THE VIRIDIAN FOLLOW THE CLEARING PROCEDURES AS SET FORTH IN THE MANUAL FOR YOUR FIREARM MAKE SURE THE WEAPON IS CLEAR AND ON SAFE BEFORE PROCEEDING PRIOR TO CLEANING DISMOUNT THE VIRIDIAN FROM YOUR WEAPON AND REMOVE THE BATTERIES IT IS RECOMMENDED THAT YOU CLEAN YOUR ACCESSORIES PERIODICALLY TO ENSURE PROPER WORKING CONDITION CAUTION po NOT USE ACIDIC OR FLAMMABLE CLEANING COMPOUNDS LASER AIMING SYSTEMS CORPORATION 12 MONTH LIMITED WARRANTY Laser Aiming Systems Corporation warrants for 12 months after purchase that its products will be free from defects in material and workmanship Laser Aiming Systems Corporation will repair or replace at its option any product or part with the exception of the battery which is found to be defective under normal use and service without charge Laser Aiming Systems Corporation s obligation
10. t any person animal or moving vehicle including aircraft INSTALLING BATTERY 4 To secure battery into place line up the threading of the Tactical Light Lens 1 Your Viridian s CR123A battery resides and turn clockwise until it reaches its within the housing located behind the stopping point Tactical Light Lens on your Viridian This battery design allows you to change CAUTION TEST VIRIDIAN your battery without removing your PERIODICALLY DURING PERI0DS Viridian from your firearm OF NON USAGE TO ENSURE See Figure A ADEQUATE BATTERY LEVELS 2 To access the Battery Compartment simply turn the Tactical Light Lens counterclockwise and remove 3 Slide the CR123A Battery 3 Volt Lithium into the housing positive side first Once the battery is in place the positive side should be to the back and the negative side to the front of your Viridian 8 FIGURE A Mounting Screw VIRIDIAN DIAGRAM Windage Adjustment Screw Elevation Adjustment Screw Rail Set Rail Set Screw Aircraft Grade Aluminum Housing Rail Set Screw 5mW Green Laser Tactical Light Lens High Output LED CHANGING THE RAIL SET For more information or to purchase Viridian Rail Sets for harder to fit weapons such as HK USP or S amp W Sigma please visit us online at www ViridianGreenLaser com Using larger sized hex wrench unscrew Rail Set Screw on each side of Viridian 2 Remove
11. umen steps down to medium then low then back to high each step is approx Y second To change modes press and release both buttons at the same time while the unit is on To enter Deep Programming mode hold down both buttons for greater than 3 seconds Continue to hold down both buttons to observe these Deep Program ming changes Release both buttons to lock in your Deep Programming change Hz or Hertz is a unit of frequency and is defined as the number of cycles per second As used here it is the number of pulses per second whether light or laser lt The Y second pause is to allow you a moment to release both buttons so you know you are at either the bottom ideal or top frequency Your Laser Light mode selections and Deep Programming setting will always be stored for the next use of your Viridian Removing the battery will return your Viridian to factory default settings Mode 1 Constant Laser Only WARNING never PUT YOUR HAND IN FRONT OF THE MUZZLE OF A FIREARM ALWAYS KEEP YOUR FINGER AWAY FROM THE TRIGGER UNTIL YOU ARE READY TO FIRE ALWAYS MAKE SURE THE WEAPON IS CLEAR AND ON SAFE BEFORE MOUNTING OR DISMOUNTING ANY ACCESSORY ONTO YOUR FIREARM ZEROING PROCEDURES WARNINGS BEFORE HANDLING ANY FIREARM WITH THE VIRIDIAN READ AND UNDERSTAND THE ENTIRE CONTENTS OF YOUR FIREARM MANUAL AND THE VIRIDIAN MANUAL ESPECIALLY THE SAFETY PRECAUTIONS AND PROCEDURES FOR SAFE FIREARMS HANDLING ALWAYS CHECK
Download Pdf Manuals
Related Search