Smoke Alarm User`s Manual IMPORTANT SAFETY INFORMATION
Contents
1. Hush Button on any other alarm will not cancel the alarm 2 The unit will reset to normal sensitivity at the end of the silenced period If additional silenced time is required simply push the Test Hush button again MAINTENANCE AND CLEANING In addition to weekly testing this smoke alarm requires yearly battery replacement and periodic cleaning to remove dust dirt and debris BATTERY REPLACEMENT Replace battery at least once a year or immediately when the low battery signal sounds once a minute Batteries should be replaced regularly as necessary Replace the batteries of the escape light if not on when being tested WARNING Do not use any other type of battery other than as specified in this manual Do not use rechargeable batteries CAUTION If the battery is incorrectly replaced the smoke alarm will not operate and may cause damage Please use high quality batteries to ensure long term performance 1 Turn smoke alarm counterclockwise to detach it from the mounting plate 2 Gently pull down smoke alarm 3 Remove battery from the compartment 4 Insert a new 9 volt battery to connector NOTE THE POLARITY OF CONNECTIONS Ensure the metal tab is fully depressed when the battery has been fitted 5 Using the Push to Test button test the smoke alarm to verify the 9V DC battery See TESTING THE SMOKE ALARM 6 Re attach the smoke alarm to the mounting plate by turning smoke alarm clockwise until it snap2. provided it is returned personally or by prepaid delivery with a copy of proof of purchase Do not post This warranty does not cover damage resulting from accidents misuse or abuse or lack of reasonable care of the product The purchaser s attention is drawn to rights it may have under the Trade Practices Act 1974 and similar state and territory legislation which cannot be excluded Subject to those non excluded rights and provisions and the above warranty Master Distributors Pty Ltd will not be liable for any injury to persons or damage to property or for any special direct or indirect or consequential loss or damage whatsoever and whether as a result of negligence or fault on the part of Master Distributors Pty Ltd or its servants agents suppliers and contractors or otherwise arising out of or resulting from whether directly or indirectly the use installation or maintenance of the smoke alarm and any warranties or representations are excluded unless given by Master Distributors Pty Ltd in writing The 9 volt battery included with this Smoke Alarm is excluded from the Master Distributors Pty Ltd 3 year Limited Warranty If this Smoke Alarm is installed for use by others please leave this document or a copy for the end user 1 Remove smoke alarm from mounting plate and check that battery is properly attached to connector 2 Clean the smoke alarm Smoke alarm beeps about once a Replace the battery See battery replacement in
3. drained or improperly connected DO NOT use any other kind of battery except as specified DO NOT connect this smoke alarm to any other type of smoke alarm or auxiliary device except those listed in this manual 2 The Test button accurately tests all smoke alarm functions Do not use any other test method Test smoke alarm weekly to ensure proper operation 3 DO NOT remove or disconnect battery to quiet unwanted alarms This will remove your protection Open windows or fan the air around smoke alarm to silence it 4 This smoke alarm may be installed by a licensed qualified electrician Observe and follow all local and national electrical and building codes for installation 5 This smoke alarm is designed to be used inside a single unit only In buildings with several units each individual living unit should have its own smoke alarms Do not install in non residential buildings This smoke alarm is not a substitute for a complete alarm system 6 Install a smoke alarm in every room and on every level of the home Smoke may not reach the smoke alarm for many reasons For example if a fire starts in a remote part of the home on another level ina chimney wall roof or on the other side of a closed door smoke may not reach the smoke alarm in time to alert household members A smoke alarm will not promptly detect a fire except in the area or room in which it is installed 7 Smoke alarms may not alert every household member
4. Family First PHOTOELECTRIC SMOKE ALARM MODEL FFP9VHEL Smoke Alarm User s Manual Please read and save this manual Photoelectric smoke alarms are generally more effective at detecting smoldering fires which can smolder for hours before bursting into flame Sources of these fires may include cigarettes burning in couches or bedding MAIN FEATURES gt DC operated photoelectric type smoke alarm gt Photoelectric sensor for slow smoldering fires gt Insect proof gt Self Test button gt Environmentally friendly non radioactive technology gt High and stable sensitivity gt With quick fix mounting bracket for easy installation gt Fitting and battery tamper resist feature gt LED operation indicator gt Extra loud alarm sound over 85 dB gt Low battery and battery missing warning indicator gt Auto reset when smoke clears SPECIFICATION gt Model Number FFP9VHEL gt Detection Type Photoelectric Chamber gt Power Source 9V DC Battery gt Standby Current 15UA max gt Alarm Current 700mA max gt Alarm Sound Level 85 Decibels at 3 meters gt Operation Temperature 5 C to 45 C gt Ambient Humidity 10 90 gt Sensitivity to Smoke 3 0 6 0 Obs m IMPORTANT SAFETY INFORMATION 1 This smoke alarm requires constant working 9 volt battery to operate properly This smoke alarm WILL NOT work if DC power is not connected or has failed or been interrupted for any reason AND the battery is removed
5. ace before you start investigating Check the house carefully in case there is a small fire smoldering somewhere Check whether there is some source of smoke or fumes for example cooking fumes being drawn past the smoke alarm by an extractor If there are frequent nuisance false alarms it may be necessary to re locate the device away from the source of the fumes If for some reason the alarm continues to sound without smoke or heat being present due to insect infestation or contamination build up for example the units can be silenced by disconnecting the mains power and removing the unit If cleaning the alarm does not correct the problem it can be returned to the manufacturer for repair or replacement HUSH FEATURE This smoke alarm has a combined Test Hush button to help you control nuisance false alarms 1 To cancel a false alarm press the Test Hush button located on the cover The alarm will automatically switch to a reduced sensitivity condition very large levels of smoke from a nearby fire will override the Hush on the smoke alarms This condition allows unwanted alarms to be silenced for a period of approximately 10 minutes The unit will flash the red light every 10 seconds instead of the normal 40 seconds to indicate the sensitivity is reduced On interconnected alarms pressing the Test Hush button on the one sensing smoke i e the one with the red light flashing every second will silence all alarms Pressing the
6. eekly and replace every 10 years Note For best protection we recommend that you install a smoke alarm in every room SMOKE ALARM PLACEMENT Typical single story home Install a smoke alarm on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area If a bedroom area hallway is more than 30 feet long install a smoke alarm at each end If there is a basement Install a smoke alarm on the basement ceiling at the bottom of the stairwell KITCHEN O DINING ROOM O BEDROOM LIVING ROOM SINGLE STORY RESIDENCE APARTMENT MOBILE HOME Typical Multi story or split level home Install a smoke alarm on the ceiling or wall inside each bedroom and in the hallway outside each separate sleeping area If a bedroom area hallway is more than 30 feet long install a smoke alarm at each end Please install a smoke alarm on the top of a first to second floor stairwell O A LIVING ROOM KITCHEN r af ter KEY MULTI STORY RESIDENCE Minimum required smoke alarm locations O Recommended additional smoke alarm locations N Smoke alarms with hush features recommended for additional protection IMPORTANT SMOKE ALARM PLACEMENT AND EXCEPTION INFORMATION 1 As close to the centre of the ceiling as possible or at least no closer than 300mm to any wall or corner 2 Install a minimum of two smoke alarms in every home no matter how small the home 3 Install a smoke alarm in each room that is di
7. every time The alarm sound is loud in order to alert individuals to a potential danger However there may be limiting circumstances where a household member may not hear the alarm i e outdoor or indoor noise sound sleepers drug or alcohol usage the hard of hearing etc If you suspect that this smoke alarm may not alert a household member install and maintain specialty smoke alarms Household member must hear the alarm s warning sound and quickly respond to it to reduce the risk of damage injury or death that may result from fire If a household member is hearing impaired install special smoke alarms with lights or vibrating devices to alert occupants 8 Smoke alarms can only sound their alarms when they detect smoke Smoke alarms detect combustion particles in the air They do not sense heat flame or gas This smoke alarm is designed to give audible warning of a developing fire However many fires are fast burning explosive or intentional Others are caused by carelessness or safety hazards Smoke may not reach the smoke alarm QUICKLY ENOUGH to ensure safe escape 9 Smoke alarms have limitations This smoke alarm is not foolproof and is not warranted to protect lives or property from fire Smoke alarms are not a substitute for insurance Homeowners and renters should insure their lives and property In addition it is possible for the smoke alarm to fail at any time For this reason you must test the smoke alarm w
8. ke alarm and explain what the sound means 2 Determine two exits from each room and an escape route to the outside from each exit 3 Teach all household members to touch the door and use an alternate exit if the door is hot Instruct them not to open the door if the door is hot 4 Teach household members to crawl along the floor to stay below dangerous smoke fumes and gases 5 Determine a safe meeting place for all members outside the building WHAT TO DO IN CASE OF FIRE 1 Do not panic stay calm 2 Leave the building as quickly as possible Touch doors to feel if they are hot before opening them Use an alternate exit if necessary Crawl along the floor and do not stop to collect anything 3 Meet at a pre arranged meeting place outside the building Call the fire department from outside the building Do not go back inside a burning building Wait for the fire department to arrive Cp These guidelines will assist you in the event of a fire However to reduce the chance that fires will start practice fire safety rules and prevent hazardous situations THREE YEAR LIMITED WARRANTY Master Distributors Pty Ltd warrants to the original consumer purchaser each new smoke alarm to be free from defects in material and workmanship under normal use and services for a period of three 3 years from the date of purchase Master Distributors Pty Ltd agrees to repair or replace at its option any defective Smoke Alarm
9. l be muted 10 minutes and then reset into normally mode after this period NOTE If the smoke density increases during this time the smoke alarm will be triggered into alarm again TESTING THE SMOKE ALARM 1 Test each smoke alarm to be sure it is installed correctly and operating properly 2 The push to test button accurately tests functions Do not use an open flame to test this smoke alarm You may ignite and damage the smoke alarm or your home 3 Test smoke alarms weekly and upon returning from vacation or when no one has been in the household for several days 4 Stand at arm s length from the smoke alarm when testing TEST ALL SMOKE ALARMS WEEKLY WITH THE FOLLOWING STEPS 1 Firmly push the TEST button and the smoke alarm will sound a loud beep and the escape light will turn on The alarm will stop sounding and the light will turn off after releasing the TEST button 2 If the smoke alarm does not sound or the light does not turn on please retest the smoke alarm DANGER If the alarm sounds and smoke alarm is not being tested the smoke alarm is sensing smoke THE SOUND OF THE ALARM HORN REQUIRES YOUR IMMEDIATE ATTENTION AND ACTION NUISANCE ALARMS If there is a nuisance alarm simply press the test hush button on the alarm to silence the unit for 10 minutes If when the alarm goes off there is no sign of smoke heat or noise to indicate that there is a fire you should get your family into a safe pl
10. nal electrical code and any local codes that may apply 1 Remove the mounting plate by turning anti clockwise at the back of the smoke alarm See figure 1 2 Insert AA batteries into the battery compartment of the mounting plate See figure 2 Ensure correct battery polarity is observed Ensure the compartment cover is properly closed 3 Secure the mounting plate to the ceiling with mounting screws See figure 3 4 Connect a new 9 volt battery to battery connector inside battery pocket of the detector 4 Cont Be sure battery is securely connected Red LED may blink briefly when battery is installed See figure 4 5 Close battery pocket door snapping it into place 6 Connect the detector to the mounting plate by using the connecting plug See figure 5 Turn clockwise to lock the detector into the mounting plate See figure 1 7 Push test button to test smoke alarm See TESTING THE SMOKE ALARM OPERATING YOUR SMOKE ALARM Once the smoke alarm has been installed A RED indicator light LED should flash approximately once a minute to indicate the battery is healthy and the unit is operating properly If smoke is detected the unit will emit a loud pulsating alarm and a RED indicator light LED will be flashing quickly until the air is clear The HUSH feature can mute the detector if it has been advertently triggered by holding down the TEST HUSH button for a few seconds The smoke alarmwil
11. s into place 7 Test the smoke alarm using Test button See TESTING THE SMOKE ALARM CHOOSING A REPLACEMENT BATTERY The unit requires one standard 9V battery The following batteries are acceptable as replacements Golden Power 6F22 Megaton 6F22 New Leader 6F22 Gold Peak 1604 Eveready 522 1222 or equivalent quality models available from electrical or hardware stores CLEANING Clean the smoke alarm at least once a month to remove dust dirt or debris Using the soft brush or wand attachment to a vacuum cleaner vacuum all sides and cover of smoke alarm Be sure all the vents are free of debris If necessary use a damp cloth to clean smoke alarm cover IMPORTANT Do not attempt to remove the cover to clean inside the smoke alarm This will void your warranty TROUBLESHOOTING Smoke alarm does not sound when tested NOTE Push test button for at least five seconds while testing WARNING DO NOT disconnect battery to quiet an unwanted alarm This will remove your protection Fan the air or open a window to remove smoke or dust from the unit PRACTICE FIRE SAFETY If the smoke alarm sounds its alarm and you have not pushed the test button this is a warning of a dangerous situation Your immediate response is necessary To prepare for such occurrences develop family escape plans discuss them with all household members and practice them regularly 1 Expose everyone to the sound of a smo
12. the maintenance minute and cleaning section Smoke alarm sounds unwanted alarms intermittently or when residents are cooking taking showers etc cleaning section PLACEMENT The alarm sounds different than I m used to It starts and stops then repeats The escape light is not on when being tested connector The alarm is operating correctly This alarm features the 1 Clean smoke alarm See cleaning in the maintenance and 2 Move smoke alarm to a new location See SMOKE ALARM internationally recognized horn signal for evacuation The alarm E r i sound pattern is 3 short beeps followed by a 2 second pause and 3 1 Remove smoke alarm from mounting plate and check if the Fa batteries of the escape light are properly attached to A Australian Standard 2 Check if the smoke alarm is connected well with the mounting plate through the connecting plug AS3786 Lic 21554 SAI Global
13. vided by a partial wall either coming down from the ceiling at least 200mm 8 Inches or coming up from the floor 4 Install a smoke alarm in lived in attics or attics which house electrical equipment like furnaces air conditioners or heaters lt 300mm min gt A 4 m _f Heatand p Best here A smoke A from fire lt Dead air space Do Not install here gt Dead air space v Do Not install here 900mm min gt A DO NOT INSTALL SMOKE ALARMS 1 Use a specialised smoke alarm with unwanted alarm control near appliances or areas where normal combustion regularly occurs near furnaces hot water heaters etc 2 In areas with high humidity like bathrooms or areas near dishwashers or washing machines Install at least 3 Metres 10 Feet away from these areas 3 Near air returns or heating and cooling supply vents Install at least 900mm 3 Feet away from these areas The air could blow smoke away from the detector interrupting its alarm 4 In rooms where temperatures may fall below 5 C or rise above 45 C 5 In extremely dusty dirty or insect infested areas where loose particles interfere with smoke alarm operation WARNING Incorrect orientation will result in a decrease in operational effectiveness HOW TO INSTALL THIS SMOKE ALARM Fig 1 Fig 2 i Fig3 Fig 4 a 4 Fig5 EE WARNING Smoke alarm installation must be in accordance with the requirements of the natio
Download Pdf Manuals
Related Search