User Manual
Contents
1. ee ee ee ee ee ee ee ee ee 2 I Software Version 1 3 L INSTRUC TON PC4000 SECURITY SYSTEM DOC NOTICE NOTICE The Canadian Department of Communications label identifies certified equipment This certification means that the equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment User should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This2. correct security code must be entered before the allowed entry time expires If an alarm occurred while the panel was armed the View Memory message will be on the display with the zone name for the zone that caused the alarm The display will keep those messages on for two minutes or until the key is pressed to return the panel to the normal arm disarm mode AUTO BYPASS HOME AWAY ARMING If a correct security code is entered and you do not exit the premises through a designated exit entry door the system will at the end of the Exit delay time arm with interior zones automatically bypassed if those interior zones have been programmed as Home away zones These zones will remain bypassed until 1 is entered to reactivate bypassed home away zones This is a convenience feature for someone who wishes to remain on the premises with the system armed That person does not have to manually bypass the home away zones To reactivate the Home away zones that have been automatically bypassed press 1 This command is a quick method of fully arming the system in residential applications before going to bed ZONE BYPASSING 1 A bypassed zone will not cause an alarm If a zone is bypassed the panel may be armed even if the zone is open Use zone bypassing when access is needed to part of the protected area Also damaged wiring or contacts on a zone may be temporarily bypassed until repairs can be made so that the panel can be
3. procedures where such actions is reasonably required and proper in its business Should any such changes render the customer s terminal equipment incompatible with the telephone company facilities the customer shall be given adequate notice to the effect of the modifications to maintain uninterrupted service GENERAL This equipment should not be used on coin telephone lines Connection to party line service is subject to state tariffs RINGER EQUIVALENCE NUMBER REN The REN is useful to determine the quantity of devices that you may connect to your telephone line and still have all of those devices ring when your telephone number is called In most but not all areas the sum of the REN s of all devices connected to one line should not exceed five 5 To be certain of the number of devices that you may connect to your line you may want to contact your local telephone company EQUIPMENT MAINTENANCE FACILITY Digital Security Controls Ltd 160 Washburn St Lockport NY 14094 1993 Digital Security Controls Ltd Toronto Canada Printed in Canada 29000226 RO
4. upon request from the installer VIEW PARTITIONS 6 ACCESS CODE 8 This function will allow the user to view the status of other partitions that their access code has been enabled for For example if an access code has been enabled for partitions 1 2 and 5 they can only view the status of these partitions To view the partition s status press the lt or gt key to toggle through the partitions The partition labels will be displayed along with a letter to the far right The letter shows the status of that partition A means the partition is Armed R means the partition is secure and Ready to be armed N means Not ready to be armed because zones are not secure This function must be enabled by the installer for the user to be able to enter this section If the installer does not enable this section you will hear an error tone when selecting this section INSTALLERS PROGRAMMING COMMANDS 8 INSTALLER S CODE This command is used by the installer to program the PC4000 AT HOME ARMING 9 ACCESS CODE Entering 9 before the arming code arms the panel without any entry delay on the delay zones and bypasses zones that are defined as Home away This command is used for arming the system while at home Once the panel is Armed in this mode using 1 will remove the bypass from those zones defined as Home away if they have NOT been manually bypassed The 1 command as used here only
5. ansmission to the monitoring station The installer can program this key to sound the alarm or to transmit the alarm silently ARMING Close all protected doors and windows and stop movement in areas covered by motion detectors The Enter Code to Arm System message should be on the LCD display The system cannot be armed unless the Enter Code to Arm System or Secure System or Enter Code message is displayed Enter a 4 Digit Security Code As each digit is entered the keypad will beep a f the security code was entered incorrectly the keypad will beep steadily for 2 seconds f the code was entered correctly but the system was not secure due to an open zone the keypad will beep quickly followed by a steady tone When the correct code is entered the Exit delay in Progress message will be displayed and the keypad will beep quickly A timer will appear in the right side of the display indicating the remaining time in the exit delay Exit the premises through the designated exit entry door At the end of the allowed exit time the message on the keypad will change to Enter Code to Disarm System DISARMING Enter the premises through the designated exit entry door The keypad buzzer will be on Go to the keypad and enter the 4 digit security code If an error is made in entering the code press the key and enter the code again The Armed light will go out and the keypad buzzer will stop The
6. armed To bypass zones enter 1 An access code may be required if the installer has enabled that option A menu will appear 0 Bypass Zones This selection takes you immediately to bypassing zones Use the lt gt to select the zones to be bypassed and press the key to select the zone A x will appear beside the zone label to indicate the zone will be bypassed when the partition is armed A zone search routine allows the user to find the desired zone to bypass by entering in the first letter of the zone to search for and pressing one of the lt gt keys The lt key will search for the first zone on the partition that begins with the letter selected The gt key will search for the last zone on the partition that begins with the letter selected The letters of the alphabet have been divided up among the 1 9 number keys on the keypad 0 ABC DEF GHI JKL MNO PQR QD STU VWX YZ 1 Clear Bypasses Removes all bypasses from all the zones in your partition and then takes you to bypassing zones None of the zones will have a beside them 2 Recall Bypasses Selecting this will bypass all the same zones that were selected the last time zones were bypassed This is for users that are always bypassing the same zones 3 Previous Menu takes you back to the Enter Code to Arm System When the PC4000 is programmed the ability to bypass certain zones may have been elim
7. e installer to be silent The keypad will sound for one minute before Auto Arming unless the Auto Arm is aborted To abort the Auto Arm and silence the keypad press any key during the pre alert The Auto Arm will be attempted at the same time the following day The PC4000 can be programmed to require a code to be entered for a user to abort the Auto Arm by the installer Upon selecting the Auto Arm Control function the Auto Arm Control menu will appear on the LCD keypad 0 Auto Arm 1 Auto Arm Time Auto Arm toggles Y or N to enable or disable the Auto Arm function Auto Arm time is the time the partition will automatically arm itself every day NOTE The Auto Arm time is a 24 hour clock and times must be entered as two digit numbers E g HH 01 02 10 11 23 24 MM 00 01 35 36 58 59 Enter 4 digits representing the time in hours and minutes HH MM based on 24 hour or military time Always enter a leading zero where only one digit is required 8 05 am would be entered as 0805 1 30 pm would be entered as 1330 KEYPAD SETUP 6 ACCESS CODE 3 This function allows the user to adjust the backlighting and contrast of the LCD 4500 keypad When this function is selected the Keypad Setup menu will appear on the keypad Bright Control adjusts the level of backlighting on the LCD display and the backlighting on the keys Contrast Control adjusts the contrast of the lettering on the LCD display U
8. etwork If the problem is with this equipment the customer shall discontinue use until it is repaired TELEPHONE CONNECTION REQUIREMENTS Except for the telephone company provided ringers all connections to the telephone network shall be made through standard plugs and telephone company provided jacks or equivalent in such a manner as to allow for easy immediate disconnection of the terminal equipment Standard jacks shall be so arranged that if the plug connected there is withdrawn no interference to the operation of the equipment at the customer s premises which remains connected to the telephone network shall occur by reason of such withdrawal INCIDENCE OF HARM Should terminal equipment or protective circuitry cause harm to the telephone network the telephone company shall where practicable notify the customer that temporary disconnection of service may be required however where prior notice is not practicable the telephone company may temporary discontinue service if such action is deemed reasonable in the circumstances In the case of such temporary discontinuance the telephone company shall promptly notify the customer and will be given the opportunity to correct the situation The customer also has the right to bring a complaint to the FCC if he feels the disconnection is not warranted CHANGE IN TELEPHONE COMPANY EQUIPMENT OR FACILITIES The Telephone Company may make changes in its communications facilities equipment operations or
9. ick Arm 1 Quick Exit 2 Auto Arm Control 3 Keypad Setup 4 Bell Comm Test 5 Door Chime 6 Spec Messages 7 User Call Up 8 View Partitions Item 0 1 5 and 6 turn on and off various functions To enable or disable these functions press the key to toggle Y or N on the keypad Y The function is enabled N The function is disabled QUICK ARM 6 ACCESS CODE 0 The Quick Arm feature is enabled by toggling to Y on the keypad When enabled the panel can be armed by entering 0 One time use access codes should not be used with the quick arm feature The one time use code is only erased when used to arm QUICK EXIT 6 ACCESS CODE 1 The Quick Exit function is enabled by toggling to Y on the keypad When enabled the user can exit through any delay zone without altering the status of the system by entering 0 on the keypad AUTO ARM CONTROL 6 ACCESS CODE 2 This function must be enabled by the installer or an error tone will sound when this section is entered The PC4000 can be programmed to arm a partition at the same time each day by enabling the Auto Arm function and programming the Auto Arm time At the selected Auto Arm time the system will give a pre alert The keypad begins to sound and the Bell Siren will pulse once every 10 seconds to alert anyone on the premises that the system is about to arm The Bell Siren pulse can be programmed by th
10. ids stored safely in closed containers in a well ventilated cool area Cleaning with flammable liquids should be avoided 3 Are fire hazardous materials matches well out of reach of children 4 Are furnaces and wood burning appliances properly installed clean and in good working order Have a professional evaluation FAMILY ESCAPE PLANNING There is often very little time between the detection of a fire and the time it becomes deadly It is thus very important that a family escape plan be developed and rehearsed 1 Every family member should participate in developing the escape plan 2 Study the possible escape routes from each location within the house and since many fires occur at night special attention should be given to the escape routes from sleeping quarters 3 It is essential that escape from a bedroom be possible without opening the interior door To facilitate such an escape Make sure that doors and or windows that open to the outside are easily opened e g not painted shut Simply making the exit may be too difficult for children the elderly or handicapped plans for rescue should be developed This includes making sure that those who are to perform the rescue can promptly hear the fire waming signal a f the exit means is above the ground level an approved fire ladder or rope should be provided as well as training in its use Exits on the ground level should be kept clear e g remove snow from exterior pat
11. inated by the installer In this case the message for those zones will not come on in response to the bypass command The 1 command should be used to see which zones are bypassed so that zones are not unintentionally bypassed Zone bypasses are automatically cancelled when the panel is disarmed NOTE At no time can any armed zone be bypassed While the system is disarmed bypassing can be used to temporarily silence the door chime feature on a zone Simply bypass the zone that the door chime feature enabled The keypad will no longer beep when the zone is opened Be sure to clear all bypasses before arming to ensure no zones are unintentionally bypassed TROUBLE DISPLAY 2 The PC4000 continuously monitors a number of possible trouble conditions If one of these conditions occurs the keypad TROUBLE indicator will light and the audible indication will sound two short beeps every 10 seconds When the key is pressed the audible indication will stop on that partition but the trouble indicator light will remain ON until the trouble is cleared Trouble conditions can also be transmitted to the monitoring station Press the then 2 keys to display the trouble conditions Low stand by battery Loss of time on internal clock AC power failure COMBUS communications fault a Auxiliary supply trouble COMBUS low voltage Telephone line trouble a Internal fault Bell circuit failure 4204 Battery TBL S
12. io doors The family should have a predetermined assembly point where everyone can be accounted for e g across the street or at a neighbours Once everyone is out of the house call the Fire Department Agood plan emphasizes quick escape Do not investigate first or attempt to fight the fire and do not attempt to rescue valuables or pets as this takes up valuable time Once outside do not re enter the house Wait for the fire department Write the plan down and rehearse frequently so that should an emergency arise everyone will know what they are to do Revise the plan as conditions change e g more or fewer family member or changes to the house Make sure your fire warning system is operational by conducting weekly tests as noted elsewhere in this manual If you are unsure about system operation contact your installing dealer t is recommended that you contact your local fire department and request further information on home fire safety and escape planning If available have your local fire prevention officer conduct an in house fire safety inspection MAINTENANCE With normal use the system requires minimum maintenance The following points should be observed 1 Do not wash the keypad with a wet cloth Light dusting with a barely damp cloth should remove normal accumulations of dust 2 The battery bell test is designed to determine battery condition however it is recommended that the stand by batteries be replaced ever
13. minaison du circuit boucl peut etre constitu e de n import quelle combinaison de dispositifs pourvu que la somme des indices de charge de l ensemble des dispositifs ne d passe pas 100 L indice de charge de cet dispositif est 10 INTRODUCTION The LCD 4500 keypad provides easy to understand English language information about the status of your security system and makes daily operation simple by prompting the user through each operation The keypad provides audible feedback each time a key is pressed and with unique audible sequences it signals troubles and the correct or incorrect entry of information ABOUT YOUR SECURITY SYSTEM Your DSC security equipment has been designed to give you the greatest possible flexibility and convenience The LCD 4500 keypad will guide you through each operation with English language prompts Read this manual carefully and have your installer instruct you on system operation and on which features have been implemented on your system FIRE DETECTION This equipment is capable of monitoring fire detection devices such as smoke detectors and providing a warning alarm if a fire condition is detected Good fire detection depends on having adequate numbers of fire detectors placed in appropriate locations This equipment should be installed in accordance with N F P A standard 74 N F P A Batterymarch Park Quincey MA 02269 Carefully review the Family Escape Planning guidelines in this manual NOTE Your ins
14. moke detector loop trouble 4204 AC Trouble Unsuccessful communication 4204 Aux Trouble attempt with monitoring station Press to return to READY Low Battery A battery trouble will be displayed if the battery is low disconnected or the battery fuse fails AC Power Failure There is no audible annunciation on AC power failure The system Trouble light will come ON but the audible indication will not sound until there is a low battery condition Auxiliary Supply Trouble A trouble is generated if the auxiliary fuse fails Telephone Line Trouble A telephone line trouble is generated when the line voltage drops below 3 volts for more than 30 seconds A keypad trouble is generated when the system is disarmed and if selected a local alarm sounds when the panel is armed Unsuccessful Communication f the digital communicator is unsuccessful in communicating with the monitoring station after 10 attempts a Fail to Communicate trouble is generated If a later attempt to communicate is successful the trouble is cleared Bell Circuit Failure f the bell fuse opens or the bell circuit is open a keypad trouble and a Bell Circuit trouble transmission are generated Smoke Detector Loop Trouble f a FIRE loop is open circuit a keypad trouble and a Fire Loop trouble transmission are generated A trouble on the FIRE loop will unconditionally initiate an audible indication on the keypad This means that even if any other previous tro
15. nce to television or radio reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Re orient the receiving antenna Relocate the alarm control with respect to the receiver Move the alarm control away from the receiver Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user may find the following booklet prepared by the FCC helpful How to Identify and Resolve Radio Television Interference Problems This booklet is available from the U S Government Printing Office Washington D C 20402 Stock 004 000 00345 4 IMPORTANT INFORMATION NOTIFICATION TO TELEPHONE COMPANY Upon request the customer shall notify the telephone company of the particular line which the connection will be made and provide FCC registration number and the ringer equivalence of the protective circuit FCC Registration Number F53CAN 73256 AL E Ringer Equivalence Number 0 1B MALFUNCTION OF THE EQUIPMENT In the event that this equipment should fail to operate properly the customer shall disconnect the equipment from the telephone line to determine if it is the customer s equipment which is not working properly or if the problem is with the telephone company n
16. ning this product In no event shall Digital Security Controls Ltd be liable for any direct or indirect or consequential damages loss of anticipated profits loss of time or any other losses incurred by the buyer in connection with the purchase installation or operation or failure of this product WARNING Digital Security Controls Ltd recommends that the entire system be completely tested on a regular basis However despite frequent testing and due to but not limited to criminal tampering or electrical disruption it is possible for this product to fail to perform as expected APPENDIX A LIST OF AVAILABLE ASCII CHARACTERS FCC COMPLIANCESTATEMENT CAUTION Changes or modifications not expressly approved by Digital Security Controls Ltd could void your authority to use this equipment This equipment generates and uses radio frequency energy and if not installed and used properly in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for Class B device in accordance with the specifications in Subpart B of Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in any residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interfere
17. nn ne doit pas oublier qu il est possible que la conformit aux conditions nonc es ci dessus n empechent pas la d gradation du service dans certaines situations Actuellement les entreprises de t l communication ne permettent pas que l on raccorde leur mat riel a des jacks d abonn sauf dans les cas pr cis pr vus par les tarrifs particuliers de ces entreprises Les r parations de mat riel homologu doivent etre effectu es par un centre d entretien canadien autoris d sign par le fournisseur La compagnie de t l communications peut demander l utilisateur de d brancher un appareil la suite de r parations ou de modifications effectu es par l utilisateur ou cause de mauvais fonctionnement Pour sa propre protection l utilisateur doit s assurer que tous les fils de mise la terre de la source d nergie lectrique des lignes t l phoniques et des canalisations d eau m talliques s il y en a sont raccord s ensemble Cette pr caution est particuli rement importante dans les r gions rurales AVERTISSEMENT L utilisateur ne doit pas tenter de faire ces raccordements lui meme il doit avoir recours a un service d inspection des installations lectriques ou a electricien selon le cas L indice de charge IC assign a chaque dispositif terminal indique pour viter toute surcharge le pourcentage de la charge totale qui peut etre raccord e a un circuit t l phonique boucl utilis par ce dispositif La ter
18. precaution may be particularly important in rural areas CAUTION Users should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 The Load Number of this device is 10 AVIS L tiquette du minist re des Communications du Canada identifie le mat riel homologu Cette tiquette certifie que le mat riel est conforme certaines normes de protection d exploitation et de s curit des r seaux de t l communications Le Minist re n assure toutefois pas que le mat tiel fonctionnera la satisfaction de l utilisateur Avant d installer ce mat riel l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l entreprise locale de t l communication Le mat riel doit galement tre install en suivant une m thod accept e de raccordement Dans certains cas les fils int rieurs de l entreprise utilis s pour un service individuel a ligne unique peuvent tre prolong s au moyen d un dispositif homologu de rassordement cordon prolongateur t l phonique interne L abo
19. removes the bypass from zones that were automatically bypassed with the 9 command QUICK ARM 0 Entering 0 is accepted as a valid arming code when the Quick Arm feature is activated This command is often used when individuals are required to arm the system but not disarm it This could be used with home visitors in the case of a residential alarm or junior employees and maintenance staff in the case of a commercial alarm See instructions in the 6 User Functions Command section for activating the Quick Arm feature QUICK EXIT 0 WHEN ARMED Entering 0 when the partition is armed will allow the user 2 minutes to exit the premises through any delay zone without altering the status of the system if the Quick Exit feature is enabled After 0 is entered into an armed system one and only one delay zone may be tripped Any additional activity on any other active zone will cause that zone to begin its alarm sequence FIRE SAFETY IN THE HOME Most fires occur in the home and to minimize this danger it is recommended that a household fire safety audit be conducted and a family escape plan be developed HOUSEHOLD FIRE SAFETY AUDIT 1 Are all electrical appliances and outlets in a safe condition e g frayed cords over loaded lighting circuits If you are uncertain about the condition of your electrical appliances or household service have a professional evaluation 2 Are all flammable liqu
20. rystal Display and command entry keys The keypad is used to send commands to the system and to display the current system status The keypad s will be mounted in convenient locations inside the protected premises close to the exit entry doors The security system has several zones or areas of protection and each of these zones will have one or more detection sensors connected to it motion detectors glassbreak detectors door contacts or shock sensors When a sensor is in alarm the zone in alarm will be displayed on the LCD 4500 TROUBLE AND ARMED LED DISPLAYS The LCD 4500 has a yellow LED on the right side of the keypad which represents the trouble status of the panel There is a red LED just below the yellow one which represents the armed status of the panel KEYPAD ZONES There are three keys on the keypad labeled F Fire A Auxiliary and P Panic These keys are only functional if they have been programmed by the installer The installer should indicate which of these keys are active by placing a colored label next to the key F FIRE Holding this key down for two seconds will sound a fire alarm The alarm will sound pulsing and a transmission will be sent to the monitoring station The keypad will sound three beeps once the panel has accepted the alarm A AUXILIARY Holding this key down for two seconds will send a transmission to the monitoring station P PANIC Holding this key down for two seconds will send a tr
21. se the lt gt keys to toggle through the eight different settings and press to select the level of preference BELL COMM TEST 6 ACCESS CODE 4 This option allows the end user to test the system The bell s and keypad buzzer s are activated for two seconds and a test code transmission will send to the monitoring station DOOR CHIME 6 ACCESS CODE 5 The Door Chime feature is enabled or disabled by pressing the key to toggle from N to Y or Y to N When the chime zone is activated the keypad will beep quickly 5 times The Beeping on doors can be eliminated temporarily by using zone bypass only when the panel is disarmed SPEC MESSAGES 6 ACCESS CODE 6 This function enables two special event messages to be displayed when one of the special events occurs The first message is Fail to Arm It will be displayed if the user is unable to arm the partition after entering a valid code e g because of activity on the zones The second message is Alarm When Armed It will be displayed if an alarm occurred during the previous armed period The messages are programmed by the installer USER CALL UP 6 ACCESS CODE 7 This function must be enabled by the installer When selected the panel will call the downloading computer The downloading computer must be waiting for the panel to call before downloading can be performed Only use this function
22. taller must enable the fire detection portion of this equipment before it becomes functional important Note __ A security system cannot prevent emergencies It is only intended to alert you and if included a monitoring station of an emergency situation Security systems are generally very reliable but they may not work under all conditions and they are not a substitute for prudent security practices or life and property insurance Your security system should be installed and serviced by qualified security professionals who should instruct you on the level of protection that has been provided and on system operation MONITORING This system is capable of transmitting alarms troubles and emergency information over telephone lines to a monitoring station If you inadvertently initiate an alarm immediately call the monitoring station to prevent an unnecessary response NOTE The monitoring function must be enabled by the installer before it becomes functional GENERAL SYSTEM OPERATION Your security system is made up of a PC4000 and one or more LCD 4500 and various detectors and sensors The DSC control panel will be mounted out of the way in a utility room or basement The metal cabinet contains the system electronics fuses and stand by battery There is normally no reason for anyone but the installer or service person to have access to the control panel The LCD 4500 keypads have an audible indicator an alphanumeric LCD Liquid C
23. uble has been silenced a FIRE loop trouble will restart the keypad buzzer Loss of Internal Time When the PC4000 is powered up the internal time of day clock needs to be set to the correct time Programming the time will clear this trouble COMBUS Communications Fault Contact installer COMBUS Low Voltage Contact installer Internal Fault Contact installer 4204 Battery TBL If any PC4204 relay output module s battery drops below 11 3 volts a battery trouble is generated The battery voltage is checked once every 4 minutes So the battery trouble may not restore instantly when the battery voltage is restored 4204 AC Trouble f any PC4204 relay output module loses incoming AC power the keypad trouble light will indicate a 4204 AC trouble But there will be no audible annunciation until there is also a low battery condition 4204 AUX Trouble f the Aux fuse on any PC4204 relay module should open or if the Aux supply is overloaded a 4204 Aux trouble is generated 5 ALARM MEMORY DISPLAY 3 Press then 3 to enter the alarm memory mode Any alarm caused during the last armed period will be displayed The Alarm Memory message will only be displayed when an alarm occurred during the last armed period Press to return to READY USER FUNCTIONS COMMAND 6 ACCESS CODE Enter k 6 Access Code and then use the lt gt keys to display the items of the function menu Press to select an item 0 Qu
24. y three years 3 For other system devices such as smoke detectors passive infrared ultrasonic or microwave motion detectors or glassbreak detectors consult the respective manufacturer s literature for testing and maintenance LIMITED WARRANTY Digital Security Controls Ltd warrants that for a period of twelve months from the date of purchase the product shall be free of defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty Digital Security Controls Ltd shall at its option repair or replace the defective equipment upon return of the equipment to its factory This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling or damage due to causes beyond the control of Digital Security Controls Ltd such as lightning excessive voltage mechanical shock water damage or damage arising out of abuse alteration or improper application of the equipment The foregoing warranty shall apply only to the original buyer and is and shall be in lieu of any and all other warranties whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd This warranty contains the entire warranty Digital Security Controls Ltd neither assumes nor authorizes any other person purporting to act on its behalf to modify or to change this warranty nor to assume for it any other warranty or liability concer
Download Pdf Manuals
Related Search