Manual - ITM Instruments Inc.
Contents
1. 3 Installation and 3 3 1 Capture Hood 3 3 2 Assembling the Frame 4 3 3 Installing the Portable 4 3 4 Installing the Main 5 _______ 5 4 1 Communication and Supplying Power with the AC Adapter 5 4 2 Supplying Power with Batteries 6 Ao ONOFF n 7 4 4 Keypad Operation d erii E SR d uote RS DR Marra 7 4 5 Incline Adjustment Settings of the InstrumMent 8 4 6 Back Pressure Compensation On Off 9 AT WNC AS TT AA 10 4 7 1 Start and enter into the main 10 4 7 2 Single Measurement Mode 10 4 7 3 Running Average Measurement Mode 11 4 7 4 Back Pressure Compensation Measurement Mode 12 5 Display Menu settings uctus uius be uude DS Pt D Dau 12 221 E E em 132. CAPTURE HOOD MODEL 6710 INSTRUCTION MANUAL Be sure to read this manual thoroughly before using the instrument Q 12 10 1 800 561 8187 www MUI com information itm com Thank you for your purchasing instrument This is a precision instrument please read this instruction manual carefully before using the instrument and pay attention to all the cautions under the instructions 1 800 561 8187 www com information itm com Composition amp Parts B Standard part Model No 6710 Air quantity temperature humidity B Standard components Carrying Case B Optional components Spechcalons Frame era EMEN adapter 2ftx Aft 1ftx Aft Fabric hood 3ftx2ft Sftx3tt 1 800 561 8187 www com information itm com 5 amp NOTES The warning symbols mentioned in this manual are defined below symbol classifications A Danger To Prevent Serious Injury or Death Warnings in this classification indicate a danger that may result in serious injury or death if not observed A Caution To Prevent Damage to the Product Warnings in this classification indicate a risk of damage to the product that may void the product warranty if not observed Description of Symbols subject of each caution is illustrated inside the triangle e g the high temperature AThis symbol indicates a condition t
3. 1 Test ID gt Press A 7 to change the selected item as shown 5 ingle 3 Unit 4 Act Std Du below gt Press 7 tosaveorpress lt to go back without saving Under option Single press gt Single gt RunAvg B Press Test Settings 1 Test ID E Test Mode Single 3 Unit 4 Act Std Std Under option Run Avg press gt Test Settings 0 1521 gt When Run Avg is selected Save Time and Auto Save 1 Test ID 2 Test Mode Kunden must be set AvgTime Sec gt Press A or y change the Avg Time value Auto Save Off gt Press to save or press lt to quit gt Press A or 7 to change the selected item as shown 1 Test ID 2 Test Mode RunAvg AvgTime 01 Sec below gt Press gt to save press lt to go back without saving Off 10sec 20 sec 305 gt 60 sec Under option B Press press D 1 Test ID Test Mode B Press 3 Unit 4 Act Std Std 1 800 561 8187 www com information itm com 5 1 3 Set Units of Measure for Airflow Temperature and Atmos For available units refer to the below chart Display shows Available units To change the units of measure follow these steps Settings E Z gt Under Test Settings select the option 3 Unit Test 2 Test Mode Single z m E unit gt Press D enter to the Unit settings or press lt to 4 Act Std Std
4. return to MENU E Airflow gt Press or V to select option item 1 2 or 3 2 Temperature 3 Atmos gt Press gt to change the selected item Under option 1 press gt ALLE gt Press A or to change the selected unit as shown 1 Airflow 2 Temperature s below 3 Atmos gt Press gt to save press lt 1 to quit CFM gt 1 5 Under option 2 press gt XX 1 Airflow gt Press A or 7 to change the selected unit as shown 2 Temperature below gt Press gt to save press lt 1 to quit Under option 3 press gt Tm Press A or to change the selected unit as shown 2 Temperature below 3 Atmos kPa gt Press gt to save or press lt to quit kPa inHg 1 800 561 8187 www com information itm com 5 1 4 Actual flow Standard flow settings This setting is for selecting Actual air flow ACT or Standard air flow STD Test Settings 1 Test ID 2 Test Mode 3 Unit E Act Std 1 Test ID 2 Test Mode 3 Unit 4 Act Std 1 Test ID 2 Test Mode 3 Unit Act Std Single Std Single 514 Single Std Under the Test Settings select option 4 Act Std gt Press to enter or press lt to return to MENU gt Press A or 7 change the settings as shown below gt Press to save the changes or press to quit Act S
5. A Test ID can contain up to 100 Cycles The maximum number of Test IDs is 30 Any new Sample will be saved to the current Test ID You can change the current Test ID at any time to keep your data organized Press lt to return to the MENU and the settings will not be saved Refer to the figures as below Test Settings fl Test ID 4 2 Test Mode Single gt Under Test Settings press A or 7 to choose option 3 Unit is is E Item Test ID gt Press gt to change the Test ID setting Test ID Fl Select ID 2 Add New ID E Press A or y to select a menu item Total ID 30 gt Press gt to enter a setting Test ID N gt Press to increase or decrease the Test ID 2 Add New ID Total ID 30 gt Press for save your changes or press lt to quit Under option 2 press gt Test ID 1 Select ID 2 Add New ID Total ID 30 gt Press A or W change the settings gt Press gt to save your changes or press to quit 1 800 561 8187 www com information itm com 5 1 2 Test Mode settings This setting is for change the test mode amp the settings about the test modes Refer to the steps below iH Under Test Settings press A or x7 to select 2 Test 1 Test ID E Test Mode Single 3 Unit Mode 4 Act Std Std Press to enter into the Test Mode setting gt Press lt to return to MENU
6. could affect the accuracy of a measurement Users can see the air port through the clear windows at the top of the capture hood ensuring it is lined up correctly Fiberglass poles support the fabric hood A velocity matrix is fixed on the base and airflow is tested through sixteen measuring points on the cross sections of the matrix The sensor will measure airflow and correct for air pressure and temperature ensuring an accurate reading every time 1 1 Product features Measure air flow temperature and humidity at the same time Two kinds of tests are available for supply flow and exhaust flow Wide test range 40 4300 m h Large Storage capacity 3000 records e 3 5 inch color LCD LCD tilts up to 30 easy viewing Back pressure compensation Automatic air pressure and temperature correction Light weight compact configuration for easy transportation 1 800 561 8187 www com information itm com 2 Capture Hood Structure The capture hood consists of a fabric hood main structure and instrument base The structural drawing is below Fabric hood De Instrument base Main structure 2 1 Instrument Base 1 The exterior structure of the base as below 2 The internal structure of the base as below Portable handle Back pressure on off Base button Measurement matrix Main structure Test handle 3 Matrix There are sixteen measuring points for t
7. CO LTD 2610 51 Wulihe Street Heping District Shenyang PRC TEL 024 23846440 83951688 83951788 FAX 024 2389841 7 820 URL http www kanomax com cn KANOMAX INSTRUMENT SHENYANG INC 9 Zheng kun Road Shenbei New District Shenyang PRC TEL 024 89730178 FAX 024 89730177 USA INC P O Box 372 219 U S Highway 206 Andover New Jersey 07821 U S A TEL 800 247 8887 International 1 973 786 6386 FAX 1 973 786 7586 URL http www kanomax usa com E mail info kanomax usa com LIJAPAN KANOMAX JAPAN INC 2 1 Shimizu Suita City Osaka 565 0805 Japan TEL 81 6 6877 0183 FAX 81 6 6879 5570 URL http www kanomax co jp E mail sales kanomax co p 1 800 561 8187 www com information itm com
8. to change the backlight setting as 2 Time 13 10 10 3 Backlight 4 Auto Shut below gt Press gt to save or press lt to quit 44 P 8 High Normat gt ow 1 Data 2012 06 01 2 Time 13 10 10 gt Press A or 7 to select an option as below 3 Backlight o s wl 4 Auto Shut Under option 4 press gt Press gt to save your changes or press lt 1 to quit 10min gt 20min 30min gt 60min Off 1 800 561 8187 www com information itm com 5 3 processing settings 1 Test Setting 2 General Settings Record Processing EU NUT SET Press gt to select Record Processing Press Frin E Under MENU select option 3 Record Processing lt return to the main interface 2 Delete E gt Press A or 7 to select option 1 or 2 gt Press to select a setting to change or press lt to quit 2 Test ID 01 Total 30 XX 4 The means wind direction of air flow in Display LUE Press to select an ID or Cycle No as below d i lows H 534 LUST gt Press A or 7 to setan ID or Cycle No 2012 06 01 13 15 08 gt Press lt to quit ID Cycle Under option 2 press gt Detele Delete 2 Delete IDs gt settings Delete includes Delete All Delete 105 Select ID 12 Select Cycl
9. 5 1 1 Test ID 2 14 5 1 2 Test Mode settings gt 15 5 1 3 Set Units of Measure for Airflow Temperature and Atmos 16 1 800 561 8187 www com information itm com 5 1 4 Actual flow Standard flow settings 17 SPEC CIE uuu 18 5 3 Data processing settings 19 QE TEE 20 OPIN 5 ERE 21 6 6 2 23 7 Common Trouble Shooting gt 24 8 Warranty and 25 D uu 25 e AE AA A A A a 25 1 800 561 8187 www com information itm com 1 Introduction The model 6710 is used to measure the air at the supply and the exhaust points of HVAC system There are several interchangeable hoods of various sizes so it s easy to find one that will match the size of the supply and exhaust points of any HVAC system The standard size hood is 2ftx2ft 610mmx 610mm Four additional sizes are also available as options 5 gt 2ftx4ft 610mmx1220mm lt Tftx4ft 05 1220 lt 2ftx3ft 610mmx915mm lt 3ftx3ft 915mmx915mm The capture hood is designed to fit tightly over the air port to eliminate any leakage which
10. able and connect again Motor movement disorders when Check the connection between the instrument and the cable testing Check the cable and connect again 1 800 561 8187 www com information itm com 8 Warranty and After service 8 1 Warranty Seller warrants the goods sold hereunder under normal use and service as described in the operator s manual shall be free from defects for a period of one year from the date of shipment to the customer 8 2 After service Check the Common Trouble Shooting table and see if your problem is listed there f other problems occur please contact the factory see the last page for contact information If the problem is a result of manufacturer s defect the parts repaired or replaced as a result of repair services are warranted to be free After the one year warranty period the customer will be charged based on the relative cost of the work done such as instrument calibration repair etc Accessories and parts for repair or replacement will be stocked for a minimum of 5 years after production of the unit ends To schedule a repair or calibration please contact the factory Information for After service Product Name Capture Hood Model Product Series Symptom detail descriptions Order date Year Month Day 1 800 561 8187 www com information itm com 74 LICHINA SHENYANG KANO SCIENTIFIC INSTRUMENT
11. e 000 Delete Cycles 1 800 561 8187 www com information itm com Under option 1 press Detele 1 Delete All gt Press or to select option item as below 2 Delete IDs Select ID 05 3 Delete Cycles Select ID 12 Select Cycle 000 to 9 uit Yes Press gt for 2 seconds to save the changes or press Under option 2 press D Detele 1 Delete All 2 Delete IDs gt Press A or 7 to select ID No Select ID 3 Delete Cycles 1 Select ID 12 Press gt to save changes or press lt to quit Select Cycle 000 Detele 1 Delete All gt Press A or 7 to select option item as below 2 Delete IDs Select ID 05 3 Delete Cycles gt Press gt for 2 seconds to save the changes or press Select ID 12 Select Cycle 000 1 to quit Yes Under option 3 press Detele 1 Delete All 2 Delete IDs Select Dc gt For Delete Cycles refer to the operation steps in 3 Delete Cycles Select ID Select Cycle 000 Delete IDs 5 4 Communication settings Before selecting option 4 Communication ensure the instrument is connected to a PC If you quit or disconnect the cable the instrument will return to the waiting screen as shown on the right below Communication 1 Test Setting 2 General Settings 3 Record Processing Confirm the Connection El Communication Waiting 5 Print Waiting for communica
12. e Portable Handle To install the handle line it up with the mounting hole as shown in step CD and 2 below Step 8 shows the handle installed Note The support poles and the portable handle should be disassembled before acking the capture hood in the carrying case to avoid damaging the case 1 800 561 8187 www com information itm com 3 4 Installing the Main structure To install the Main structure 1 set the bottom of the panel in the holder on the unit base 2 and gently push the top of the panel backwards 8 until it locks into place To remove it simply reverse the procedure 4 Operation directions 4 1 Communication and Supplying Power with the AC Adapter ID The main structure is connected to a PC To power the instrument with the optional AC adapter refer to figures 2 and 3 When the AC adapter is connected and batteries are installed power will be supplied from the AC adapter The specification of the AC adapter is I P AC 110 240V 50 60 HZ O P DC 5V 2 POWER b The AC adapter supplies power for the main 3 The AC adapter also supplies power for the Capture hood 1 800 561 8187 www com information itm com 4 2 Supplying Power with Batteries gt 4AA size batteries be used for a power supply gt Press the compartment cover lock refer to figure CD and then slide the cover off to open the battery compartment gt Put4 A si
13. e batteries A test is running Main structure cannot be adjusted Stop the test adjust the incline settings of the instrument again Check the interface Return to the main interface Flap closed pressure was less than flap open pressure or flap DATA Error after test in open versus flap closed pressure ratio exceeds allowed limits B Press mode Test again Test data was not saved after The Cycle is full in the current ID testing Add a new ID The current ID is already a new ID Use the current ID new ID cannot be added Check the ID No lf the ID No is delete some IDs Baud rate does not match PE E Set Baud again 4 Check the connection between the instrument and the cable Display Connect Error Connect the cable again and restart Check the connection between the instrument and the cable Check the cable and connect again Low battery charge Replace or recharge the batteries The test does not begin after e instru pressing START Stop adjusting the instrument Check the back pressure plate gt the Back pressure plate Check the connection between the instrument and the cable Test exception when testing Check the cable and connect again Abnormal operation of the Check the connection between the instrument and the cable solenoid valve when testing Check the c
14. eading will display then once the reading has stabilized a flow reading will be obtained and displayed every 1 second and the wind direction will be displayed in real time Note The displayed air flow reading is a running average that is calculated based on the Avg Time settings entered by the user The greater the Avg Time the more stable the tested air flow 3 When auto save is enabled the testing flow values will be recorded at user defined intervals under the setting Save Time and the Cycle No will increase by 1 If auto save is not enabled the readings will not be saved during the test 4 The instrument will run continuously in Avg mode until you press STOP After you press stop the last reading and the related wind direction will be displayed Press SAVE to record the testing value if you do the Cycle No will increase by 1 2012 06 01 13 10 10 122 2012 06 01 13 10 10 Test ID 13 Cycle 050 Test ID 13 Cyde 050 8 Hi n T h emm 2890 n 1 800 561 8187 www com information itm com 4 7 4 Back Pressure Compensation Measurement Mode When measuring air flow in an environment with a strong wind or turbulent flow it will produce resistance for test air flow and system pressure It is suggested you turn the Back Pressure Compensation ON when the air flow is more than 1500 otherwise you can test without the Back Pressure Compensation ON 1 Wh
15. en Press mode is turned on press START and the measurement will begin 2 When Flap Open is displayed close the Back pressure plate and press START to start the measurement 3 When the measurement stops the air flow as measured with Back Pressure Compensation will be displayed 4 After the measurement stops press SAVE to save the data and the Cycle No will increase by 1 5 Display Menu settings 2012 06 01 13 10 10 8 1 In the main interface press gt for 2 sec to enter into Test ID 01 Cycle 001 WEE MENU m h 2 There are 5 option items in MENU 1 Test Settings 2 General Settings lTest Settings 2 General Settings 3 Record Processing 4 Communication 4 Communication 5 Print gt 3 Record Processing 5 Print 1 800 561 8187 www com information itm com 5 1 Test Settings Settings 1 Press A or x7 to select Test Settings and press gt to 2 General Settings 3 Record Processing enter into Test Settings Press lt return to the main 4 Communication 5 Print interface 2 The option items in Test Settings are as follows 1 Test ID 2 Test Mode 1 Test ID 2 Test Mode Single Peri 3 Unit 4 Act Std Std 4 Act Std Actual Standard air flow setting 1 800 561 8187 www com information itm com 5 1 1 Test ID setting A Test ID consists of a group of Cycles or Samples
16. en upward 4 5 Incline Adjustment Settings of the Instrument Start up the instrument and lift the capture hood to the approximate height you will be working at Press and hold the left button on base to tilt the panel downward or press and hold the right switch to tilt it up The buttons must be held down for a minimum of 3 seconds before the panel will begin to tilt While the panel is moving you will hear an audible buzzing 1 800 561 8187 www com information itm com Right switch makes the panel tilt up Note 3 conserve power avoid tilting the screen unless necessary 4 6 Back Pressure Compensation On Off Settings Turn the Back Pressure Compensation ON Flip the switch CD to the down position until it is locked Make the back pressure plate parallel with the matrix plane Back Pressure Compensation ON 1 800 561 8187 www com information itm com 4 7 4 7 1 Start and enter into the main interface To start measuring go to the main interface menu as shown below h 2012 06 01 13 10 10 TestID 13 Cycle 050 E H nr h d C a Test ID Cycle save the testing No in Cycle and the corresponding Test ID b Air flow display display the testing data of air flow c Temperature Humidity display the current temperature and humidity in real time d Keypad function display the function of the keys in the current int
17. erface Test mode display the current testing mode Single measurement Run Avg measurement and B Press measurement f Power supply mode display the current power supply from the AC adapter or the batteries 0 Brightness indicator display the current brightness of the LCD h Date Time display the current date and time 4 7 2 Single Measurement Mode SAVE 1 800 561 8187 www com informationGitm com 1 Single measurements are individual measurements When you press START the instrument will begin measuring and the air flow value will be displayed as 2 The test will stop automatically when the air flow is stable and a flow value with the corresponding wind direction will be displayed Air flow will be stable within 8 seconds The greater the air flow the shorter the time needed to stabilize 3 After the measurement stops press SAVE to record the testing value if you do the Cycle No will increase by 1 Note The value will be recorded only when testing is completed in the Single mode testing is interrupted before a stable airflow reading is displayed no data will be saved 4 7 3 Running Average Measurement Mode 1 When Avg mode is selected the instrument will constantly measure and display a running average Press START to begin the measurement 2 During the test if the air flow is not stable the flow r
18. esting air flow Measuring point for air flow 1 800 561 8187 www com information itm com 2 2 Main structure Battery Compartment Cover Display LCD Keypad Cover lock Socket for communicatio Side view Front view 2 3 Fabric Hood The fabric hood kit consists of a frame and a fabric hood with four windows as shown below Window Fabric hood 3 Installation and Assembling 3 1 Capture Hood Installation 1 Assemble the fabric hood and the frame as shown below Use the angled corners 1 and Insert a frame pole into the Continue until all 4 the stitching as a guide to frame and hook it under the corners are supported ensure the hood is straight If corner of the hood 3 by poles 4 the fabric hood is twisted it will not assemble correctly 1 800 561 8187 www com information itm com 2 The figures below are provided as a reference a Use the mark D and the stitching as a guide to ensure the hood position b Make sure the hood fully wraps around the base 3 2 Assembling the Frame detail Insert one end of a support pole into its pole mount in the base as in figure D and the other end into the frame corner as in figure 2 For the positions of the remaining 3 poles refer to figure 3 and repeat the steps as above Note The support poles always cross in an X shape when the hood is assembled To remove the poles simply reverse the steps 3 3 Installing th
19. hat requires caution including danger The N caution symbol is shown on the left 5 This symbol indicates prohibition Do not take the prohibited action shown inside or near this symbol e g the disassembly prohibition symbol is shown on the left QO This symbol indicates a mandatory action A specific action is given near the symbol AN WARNING Never bring the fabric hood into a flammable gas atmosphere Heating Otherwise the heat may cause a fire or a forbidden explosion G Do not disassemble or refit the instrument Disassembly Otherwise it may cause an electric shock or a fire prohibition Q Use the instrument properly by following the directions in this instruction manual Otherwise it may cause an electric shock or damage the sensor Using properly If abnormal smells noises or smoke occur or if liquid enters the instrument pull out the AC adapter and remove the batteries immediately Contact your distributor or the manufacturer for after service Otherwise there is possibility of electric shock fire or instrument malfunction 1 800 561 8187 www com information itm com Do not exposure the instrument to rain or water Otherwise it may cause an electric shock fire or Forbidden Injury CAUTION Remove the batteries when storing the instrument for a long period of time Do not leave drained batteries in the battery compartment and exchange the batteries promptly when they a
20. int By Cycles refer to the operation steps in Start Cycle Stop Cycle Print No Print By IDs Total Cycle 1 1 800 561 8187 www com information itm com 6 Main Specifications Flow range 40 4300 m h Air Flow Accuracy Readings 3 10 m h Air Flow gt 85 m h Resolution 1 m3 h me 0 60 Temperature LEER e Data Statistics Max Min and Avg Check and Delete Data Transmission Connect with PC USB and the Printer Standard 2ftx2ft 610mmx610mm Hood Size 2ftx4ft 610mmx1220mm 1ftx4ft 05 1220 2ftx3ft 4 610mmx915mm 3ftx3ft 915mmx915mm Power Source AC DC Power or Rechargeable batteries for 9 hours Weight Approx 3 5kg Instrument Base 2ftx2ft 610mmx610mm fabric hood Frame Standard attachment poles User Manual Communication cable Software Installer Carrying case and Main structure Fabric hood 2ftx4ft 610mmx1220mm 1ftx4ft Optional 305mmx1220mm 2ftx3ft 610mmx915mm 3ftx3ft 915mmx915mm Frame Poles Printer Cable Up down Stand max 3m and AC adapter 1 800 561 8187 www com information itm com 7 Common Trouble Shooting Symptom Possible causes troubleshooting Check the positive negative connections of the batteries Verify the batteries are inserted correctly No display Low battery charge 6Replace or recharge the batteries Low battery charge Replace or recharge th
21. operations include the keypad on the control panel as well as the switches on the base The keypad on the control panel is shown below When a keypad turns gray in the illustration on the screen that particular function is invalid MOVE ADJ SAVE SET MENU OK ESC START STOP BACK EXIT MOVE ADJ e MOVE Change an option on the current mode ADJ Change the current value 1 800 561 8187 www com information itm com SAVE Save the current test results SET Store changes or enter into the selected option s next level interface MENU On the main screen holding this down for 2 seconds will enter into the main MENU Pressing for 2 seconds will save the date or time in the General Settings Pressing for 2 seconds will delete saved data in the Record Processing START Begin a measurement in main menu STOP Stop a measurement in main menu BACK Cancel or end an operation or return to the previous screen EXIT Return to the main menu ESC Stop printing when printing Left right switches on the base Left switch Right switch Press it once quickly to start or stop a measurement Press hold it in for at least 3 seconds to tilt the control panel and LCD screen downward Right switch on base Press it once quickly to save the current data Press and hold it in for at least 3 seconds to tilt the control panel and LCD scre
22. re drained Always unplug the instrument when it is not in use Failure to do so may cause an electric shock fire or circuit damage o Seng propany Failure to do so may cause battery leakage and damage to the instrument Only use the provided AC adapter Otherwise it may damage the instrument Using properly Do not use or leave the instrument in a high temperature high humidity or dusty environment Do not leave the instrument under direct sunlight Forbidden Otherwise the instrument may not function properly or the inside components may be damaged Do not wipe the instrument with a volatile solvent The body may deform or deteriorate Use a soft dry cloth to remove stains If stains persist soak the cloth in a neutral detergent and wipe the instrument with the soft cloth Never use volatile solvents such as thinner or benzene Forbidden Never drop the unit or place heavy objects on it It may cause damage or malfunction to the instrument Forbidden 1 800 561 8187 www com information itm com CONTENTS Ve m 1 UNE AUN CS 1 2 FOO SIFU Cll Six AA EENEN 2 2 1 Hood BaSe 2 MAM SUCUT ______ ___ _6_6 _ 06 3 PANG
23. td Under option Act press gt Test Settings 1 Test ID 2 Test Mode 3 Unit 4 Act Std Single Act Atmos A 101 32 kPa Confirm the atmos 1 800 561 8187 gt When Act is selected Atmos must be set gt Press v to change the Atmos gt Press to save the changes or press lt to quit www GEE com information itm com 5 2 General Settings gt Under MENU select option 2 General Settings 1 Test Settings gt General Settings 3 Record Processing Press to enter General Settings or press lt to e return to the main interface Prin gt gt The settings includes Date Time Backlight and Auto Data 2012 06 01 2 Time 13 10 10 Shut 3 Backlight High 4 Auto Shut Off Under option 1 press gt G Setti b Press to select an option as below 1 Data 2 06 01 2 Time 13 10 10 3 Backlight High Press or 7 to change the selected value 4 Auto Shut Press for 2 seconds to save the changes or press lt toquit Year gt Month Day Press to select an option as below 1 Data 2012 06 01 2 Time 10 10 3 Backlight CHEN Press A 7 to change the selected value 4 Auto Shut Press for 2 seconds to save the changes or press Hour Minute Second lt to quit 4 1 Data 2012 06 01 gt Press v
24. tion 1 800 561 8187 www com information itm com 5 5 Print Settings Note Before printing ensure the following 1 Please select the factory configuration printer and printer cable For details refer to the printer manual lt lt RD series of mini printer gt gt 2 Baud Rate is set to 19200 The initial value is set to 19200 Under select option 5 Print 1 Test Setting 2 General Settings 3 Record Processing Press to select Print or press lt return to the main 4 Communication Print interface The setting in Print includes Print By IDs Print By Print IDs 2 Print By Cycles Cycles 1 800 561 8187 www com information itm com Under option 1 press Print 105 252 Press A or 7 to select the Start ID value Start ID p Stop ID gt Press gt to save or press lt to quit Print Total ID Print By IDs gt Press A or 7 to select the Stop ID value Start ID SS Stop ID gt Press gt to save or press lt to quit Print Total ID gt Press A or 7 to select option item as below Start ID pic Press to save the changes Or press lt to quit rint Total ID No Yes gt Press lt to stop print Start ID Stop ID Print Total ID 5 Printing D Under option 2 press Print By Cycles Select ID gt For Pr
25. ze batteries and make certain the batteries are correctly oriented New alkaline battery or rechargeable Ni MH battery can be used Never mix battery types or battery leakage or damage to the instrument may occur Replace the compartment cover refer to figure 2 The compartment cover will be automatically locked 19 When power is supplied with batteries the current charge value will be displayed on the upper of the LCD When the batteries run out of power the instrument will turn off Ly gt gt gt i Turn off t is recommended you change batteries when the power shows low 1 800 561 8187 www com information itm com 4 3 1 Getting started The LCD is displayed below for reference TN 1 Press POWER for a while 2012 06 01 13 10 10 Test ID 01 Cycle 001 l E Em 2 Then you enter into the main interface as shown in the left n figure 2 Shut down Press and hold POWER for more than 2 seconds in any mode and the instrument will turn off automatically 4 4 Keypad Operation Keypad
Download Pdf Manuals
Related Search