INNO SPOT LED WIFLY - ProSound and Stage Lighting
Contents
1. played and press ENTER Show Mode This mode allows either a single unit or several units linked together to run one of four shows that you choose See pages 11 12 for more information 1 Press the MENU button until SHND is displayed and press ENTER 2 Press the UP or DOWN buttons until you find your desired show and press ENTER UC3 Control The optional UC3 Controller not included may be used to con trol different functions including blackout Stand By Blackout the unit Function 1 Sync Strobe 1 Select Color Inno Spot LED WiFly 2 Async strobe 2 Select Gobo 3 Sound Strobe Mode Sound LED OFF Show LED LED ON Slow Blinking ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 18 Inno Spot LED WiFly WiFly Master Slave Set Up This feature will let you link units to run in a master slave mode with out the use of XLR cables 1 Follow the instructions on page 11 to set the Wireless address The addresses on each fixture must be the same 2 After you have set the WiFly address select your master unit and set your desired operating mode 3 Put the antenna in either a up position or down position then turn the WiFly on See page 11 to activate WiFly Note All antennas must be in the same position they must either be all up or all down but never at an angle 4 For the Slave units put the unit in Slave mode See page 12 Then activate WiFly 5 If every2. Press the MENU button until ULEN is displayed press ENTER 2 Either Off or On will be displayed Select On to activate and Off to deactivate ULCH This will let you select and set your WiFly address 1 Press the MENU button until ULCH is displayed press ENTER 2 X will now be displayed X representing a number between 0 15 Press the UP or DOWN buttons to find your WiFly address 3 When you have found your desired WiFly address press ENTER to confirm and exit SHND This will let you choose one of the four prepro grammed shows See show descriptions below 1 Press the either the MENU button until SHND is displayed press ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 11 Inno Spot LED WiFly System Menu ENTER Either SH 1 SH 2 SH 3 or SH 4 will be displayed 2 Press the UP or DOWN buttons to find you desired show and then press ENTER to confim and exit SHOWS Show 1 For fixtures placed on the floor the tilt movement angle is 210 Show 2 For fixtures fixed to the ceiling or truss the tilt movement angle is 90 Show 3 For fixtures placed on a table or stage The beam is pro jected at the audience s direction i e in front of the stage Pan move ment angle left to right to left is 160 Tilt movement angle is 90 Show 4 For fixtures fixed to the ceiling or truss The beam is pro
3. jected at the audience s direction i e in front of the stage Pan move ment angle left to right to left is 160 Tilt movement angle is 90 SLND This will let you set the unit as a slave ina master slave configuration 1 Press the MENU button until SLND is displayed press ENTER Either SL 1 or SL 2 will be displayed 2 Press the UP or DOWN buttons until your desired setting is dis played press ENTER to confim NOTE In a Master Slave configuration you can set one fixture to Master and then set the next fixture to SL 2 the fixtures will now have contrast movement to each other SOUN Sound Active mode 1 Press the MENU button until SOUN is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to activate sound active mode or OFF to deactivate sound active mode 3 Press ENTER to confirm ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 12 Inno Spot LED WiFly BLND Blackout or Stand by mode 1 Press the MENU button until BLND is displayed press ENTER Either Yes or No will be displayed 2 To activate Blackout tap the UP or DOWN buttons until Yes is displayed press ENTER to confim The fixture will now be in Blackout mode To deactivate Blackout mode select No and press Enter PAN Pan Inversion 1 Press the MENU button until I PAN is
4. Grounding the shield could cause a short circuit and erratic behavior COMMON DMX512 OUT DMX512 IN 3 PIN XLR DMX 3 PIN XLR Figure 2 l l XLR Male Socket XLR Female Socket XLR Pin Configuration l l 1 1 Ground 1 I I Pin 2 Data Compliment negative I I I I l l Pin 3 Data True positive Figure 3 Special Note Line Termination When longer runs of cable are used you may need to use a terminator on the last unit to avoid erratic behavior A terminator is a 110 120 ohm 1 4 watt resistor which is con nected between pins 2 and 3 of a male XLR connector DATA and DATA This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line Using a cable terminator ADJ part number Z DMX T will decrease the possibilities of erratic behavior Termination reduces signal errors and avoids signal transmission problems and interference It is always advisable Z 3 to connect a DMX terminal Resistance 120 Ohm 1 4 W between PIN 2 DMX and PIN 3 DMX of the last fixture Figure 4 ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 8 Inno Spot LED WiFly Set Up 5 Pin XLR DMX Connectors Some manufactures use 5 pin DMX 512 data cables for DATA transmission in place of 3 pin 5 pin DMX fixtures may be implemented in a 3 pin DMX line When inserting stan dard 5 pin data cables in to a 3 pin line a cable adaptor must
5. the MENU button until SLND is dis played and Press ENTER Choose either SL 1 or SL 2 and press ENTER See page 12 for more info 4 The slave units will now follow the Master unit Universal DMX Control This function allows you to use a Elatione universal DMX 512 controller to control the chases and patterns dimmer and strobe A DMX controller allows you to create unique programs tailored to your individual needs 1 The Inno Spot LED WiFly is a ten DMX channel DMX fixture See pages 21 22 for detailed description of the DMX values and traits ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 17 Inno Spot LED WiFly Operation 2 To control your fixture in DMX mode follow the set up procedures on pages 5 7 as well as the set up specifications that are includ ed with your DMX controller Use the controller s faders to control the various DMX fixture traits This will allow you to create your own programs Follow the instruction on page 11 to set the DMX address For longer cable runs more than a 100 feet use a terminator on the last fixture For help operating in DMX mode consult the manual included with your DMX controller a a Sound Active Mode This mode allows either single unit or several units linked together to run to the beat of the music 1 Press the MENU button until SOUN is displayed and press ENTER Tap the UP or DOWN buttons so that ON is dis
6. the address set on the WiFly Transceiver 4 After choosing your WiFly address you need to activate WiFly mode Follow the instructions on page 11 to activate the WiFly Mode 5 Apply power to the ADJ WiFly Transceiver The fixture must be set up to the same address as the fixture first before you apply power to WiFly TransCeiver 6 If everything is set up properly and the fixture is receiving a Wireless signal the strength of the WiFly signal will be displayed in the WiFly signal status window located on the rear of the unit LIGHT GREEN 113 127 LIGHT YELLOW 128 254 RAINBOW EFFECT SLOW FAST 255 SOUND ACTIVE GOBO 5 SHAKE 4 GOBO WHEEL 0 9 10 18 19 27 28 36 37 46 47 55 56 63 64 73 74 82 83 91 92 100 101 110 111 119 120 127 GOBO 6 SHAKE 99 112 GOBO 5 GOBO 6 OPEN SHAKE GOBO 1 SHAKE GOBO 2 SHAKE GOBO 3 SHAKE GOBO 4 SHAKE OPEN GOBO 1 GOBO 2 128 254 GOBO WHEEL ROTATION SLOW FAST 2595 SOUND ACTIVE GOBO ROTATION 0 9 10 120 121 134 135 245 246 255 GOBO 3 STOP ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 21 1 3 5 GOBO 4 CLOCKWISE FAST SLOW STOP COUNTER CLOCKWISE SLOW FAST ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 20 Inno Spot LED WiFly DMX Traits Function OHUTTER STROBE 0 7 BLACKOUT 8 15 SHUTTER OPEN 16 131 STROBING SLOW FAST 132 139 SHUTTER OPEN 140 181 FAST CLO
7. D WiFly Operation Operating Modes The Inno Spot LED WiFly can operate in three different modes In each mode you can run the fixture as a stand alone fixute or in a master slave confiugration This next section will detail the differences in the operating modes Sound Active mode The fixture will react to sound chasing through the built in programs e Show mode The fixture will run one of four shows that you choose e DMX control mode This function will allow you to control each individual fixtures traits with a standard DMX 512 controller such as the Elatione Show Designer Master Slave Operation This function will allow you to link up to 16 units together and operate without a controller The units will be sound activated In Master Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs Any unit can act as a Master or as a Slave 1 Using approved DMX data cables daisy chain your units togeth er via the XLR connector on the rear of the units Remember the Male XLR connector is the input and the Female XLR connector is the output The first unit in the chain master will use the female XLR connector only The last unit in the chain will use the male XLR connector only For longer cable runs we suggest a termina tor at the last fixture 2 On the Master unit find your desired show and set that show by pressing the ENTER button 3 On the slave units press
8. Rev 3 14 User Instructions 2013 ADJ Products LLC all rights reserved Information specifications diagrams images and instructions herein are subject to change without notice ADJ Products LLC logo and identifying product names and numbers herein are trademarks of ADJ Products LLC Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged All non ADJ Products LLC brands and product names are trademarks or registered trademarks of their respective companies ADJ Products LLC and all affiliated companies hereby dis claim any and all liabilities for property equipment building and electrical damages injuries to any persons and direct or indirect economic loss associated with the use or reliance of any information contained within this document and or as a result of the improper unsafe unsufficient and negligent as sembly installation rigging and operation of this product Europe Energy Saving Notice Energy Saving Matters EuP 2009 125 EC Saving electric energy is a key to help protecting the enviroment Please turn off all electrical products when they are not in use To avoid power consumption in idle mode disconnect all electrical equipment from power when not in use T
9. SE SLOW OPEN 182 189 SHUTTER OPEN 190 231 FAST OPEN SLOW CLOSE 232 239 SHUTTER OPEN 240 247 RANDOM STROBE 248 255 SHUTTER OPEN 0 255 DIMMER 0 100 MOVING HEAD MOVEMENT 0 7 NO FUNCTION 8 28 MOVEMENT 1 29 49 MOVEMENT 2 50 70 MOVEMENT 3 1 91 MOVEMENT 4 92 112 MOVEMENT 5 113 133 MOVEMENT 6 134 154 MOVEMENT 7 155 175 MOVEMENT 8 176 196 MOVEMENT 9 197 217 MOVEMENT 10 218 238 MOVEMENT 11 239 255 MOVEMENT 12 PQ 0 255 MOVEMENT SPEED FAST SLOW 10 PRISM EFFECT 0 6 299 NO EFFECT PRISM EFFECT ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 22 Inno Spot LED WiFly Gobo Replacement This unit comes with interchangable gobos When changing the gobos please be very careful Follow the instructions below and see the figure pictures on the next page Caution Never open the unit when in use Always disconnect the main power before attempting to change the gobos 1 To change the gobo you must remove the top half of the moving head The top half of the moving head does not have the lens attached to it 2 Unscrew the 4 phillips screws that secure the top half of the head Remove the top half of the head 3 When you remove the shell you will be able to access the gobo wheel see picture below Rotate the head so that the lens is aimed up Turn the gobo wheel with your hand until you find the gobo you would like to change 4 Using a pair of ne
10. Spot LED WiFly Instruction Manual Page 15 Inno Spot LED WiFly System Menu MENU oc i To enter the home adjustment submenu press the ENTER button for at least 5 seconds In this submenu you are able to adjust the origi nal position of the gobo wheel tilt Tilt home position and pan Pan home position OPAN Adjustment of the tilt home position 1 Press the ENTER button for at least 5 seconds then press the UP or DOWN buttons so that OPAN is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit OTIL Adjustment of the tilt home position 1 Press the ENTER button for at least 5 seconds then press the UP or DOWN buttons so that OTIL is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit OGOB Adjustment of the gobo wheel 1 Press the ENTER button for at least 5 seconds then press the UP or DOWN buttons so that OGOB is displayed press ENTER 2 Use the UP and DOWN buttons to make your adjustments and then press ENTER to confirm Press the MENU button for one second to exit ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 16 Inno Spot LE
11. be used these adaptors are readily available at most electric stores The chart below details a proper cable conversion 3 Pin XLR to 5 Pin XLR Conversion 3 Pin XLR Female Out 5 Pin XLR Male In Data True signal Pin 3 ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 9 Inno Spot LED WiFly System Menu DMX 512 Address Setting J Wifly Enable J J Wifly Channel 3 BRE Show Mode Slave Mode Sound Mode Blackout Mode Pan Inversion oF FE no HES PAA no IL eE no TT Tilt Inversion Pa aff Led Display Display Inversion Focus Adjust ECHE Selt Test LOO Temperature Test Fh S Fixture Hours ue Software Version r SPE Reset ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 10 Inno Spot LED WiFly System Menu System Menu When making adjustments you can press ENTER to confirm your setup then press and hold the MENU button for at least 3 seconds to lock it in or you can wait 8 seconds for automatic setup To exit without making any adjustments press the MENU button ADDR DMX Address Setting 1 Press the either the MENU UP or DOWN buttons until ADDR is displayed press ENTER 2 The current address will now be displayed and flashing Press the UP or DOWN buttons to find your desired address Press ENTER to set your desired DMX address ULEN This activate WiFly mode and deactivate it 1
12. ce contract and this warranty does not include maintnance cleaning or periodic check up During the period specified above ADJ Products LLC will replace defective parts at its expense with new or refurbished parts and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship The sole responsibility of ADJ Products LLC under this warranty shall be limited to the repair of the product or replacement thereof including parts at the sole discretion of ADJ Products LLC All products covered by this warranty were manufactured after August 15 2012 and bear indentifying marks to that effect E ADJ Products LLC reserves the right to make changes in design and or improvements upon its products without any obligation to include these changes in any products theretofore manufactured No warranty whether expressed or implied is given or made with respect to any accessory supplied with products described above Except to the extent prohibited by applicable law all implied warranties made by ADJ Products LLC in connection with this product including warranties of merchantability or fitness are limited in duration to the warranty period set forth above And no warranties whether expressed or implied including warranties of merchantability or fitness shall apply to this product after said period has expired The consumer s and or Dealer s sole remedy shall be such repair or replacement as is exp
13. damage to the unit never mount the unit on its side as illustrated above Be sure this fixture is kept at least 0 5m away from any flammable materials decoration etc Always use and install the supplied safety cable as a safety measure to prevent accidental damage and or injury in the event the clamp fails See next page Never use the carrying handles for secondary attachment ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 5 Inno Spot LED WiFly Installation NOTICE The suitable enviromental temperature for this light ing fixture is between 25 C to 45 C Do not place this lighting fixture in an enviroment where the temperatures are under or above the temperatures stated above This will allow the fixture to run at its best and help prolong the fixture life o S A eb 4 Ai N Ps SN L N Screw one clamp via a M12 screw and nut onto the Omega holder Insert the allen bolts into the respective holes on the bottom of the Inno Spot LED WiFly Attach the safety cable through the eyehole hook on the bottom of the base and over the trussing system or a safe fixation spot Insert the end in the carabine and tighten the safety screw ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 6 Inno Spot LED WiFly Set Up Power Supply Before plugging your unit in be sure the source volt age in your area matches the required voltage for your ADJ Inno Spo
14. days 4 Clean the internal optics with glass cleaner and a soft cloth every 30 60 days 5 Always be sure to dry all parts completely before plugging the unit back in 783 1240 2250 5250 Inno Spot LED WiFly Trouble Shooting Trouble Shooting Listed below are a few common problems that you may encounter with solutions 22300 No light output from the unit 1 Be sure you have connected your unit into a standard 120v wall outlet Be sure to voltage selector switch in the correct position 2 Be sure the external fuse has not blown The fuse is located on the rear panel of the unit 3 Be sure the fuse holder is completely and properly seated lux Unit does not respond to sound 1 Low frequencies bass should cause the unit to react to sound Tapping on the microphone quiet or high pitched sounds may not activate the unit ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 24 ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 25 Distance m 0 Inno Spot LED WiFly Warranty MANUFACTURER S LIMITED WARRANTY A ADJ Products LLC hereby warrants to the original purchaser ADJ Products LLC products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase see specific warranty period on reverse This warranty shall be valid only if the product is purchased within the United States of America inc
15. displayed press ENTER Either NO or 1 will be displayed 2 To activate the Pan inversion press the UP or DOWN buttons until lis displayed press ENTER to confim To deactivate Pan inversion select No and press Enter TLT Tilt Inversion 1 Press the MENU button until I TLT is displayed press ENTER Either NO or 1 will be displayed 2 To activate the Tilt inversion press the UP or DOWN buttons until lis displayed press ENTER to confim To deactivate Tilt inversion select No and press Enter System Menu LED With this function you can have the LED display turn off after 10 seconds 1 Press the MENU button until LED is displayed press ENTER 2 The display will show either ON or OFF Press the UP or DOWN buttons to select ON to keep the LED display on at all times or OFF to switch to have the LED display switch off after 10 seconds 3 Press ENTER to confirm To make you LED display reappear again press any button ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 13 Inno Spot LED WiFly System Menu DISP This function will reverse the display 180 1 Press the MENU button until DISP is displayed press ENTER 2 Press ENTER to flip the display Press ENTER to flip it again Press ENTER when you have made your desired setup FAD This function will allow you to focus the lens fora clear LED output 1 Press the MENU button
16. edle nose pliers grab the fixture ring that holds the gobo in place and remove the ring 5 Once the ring is removed rotate the head upside down so that the gobo falls into your hand 6 Carefully insert your new gobo and insert the fixture ring 7 Reassemble the unit ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 23 Inno Spot LED WiFly Photometric Chart Inno Spot LED WiFly Fuse Replacement Locate and remove the units power cord Once the cord has been removed located the fuse holder located inside the power socket Insert a flat head screw driver into the power socket and gently pry Ta out the fuse holder Remove the bad fuse and replace with a new one The fuse holder has a built in socket for a spare fuse be sure not to confuse the spare fuse with active fuse Inno Spot LED WiFly Cleaning Due to fog residue smoke and dust cleaning the internal and exter v nal optical lenses and mirror should be carried out periodically to optimize light output Cleaning frequency depends on the environ ment in which the fixture operates l e smoke fog residue dust dew In heavy club use we recommend cleaning on a monthly basis Periodic cleaning will ensure longevity and crisp output 1 Use normal glass cleaner and a soft cloth to wipe down the out side casing 2 Use a brush to wipe down the cooling vents and fan grill 3 Clean the external optics with glass cleaner and a soft cloth every 20
17. hank you Inno Spot LED WiFly General Information Unpacking Thank you for purchasing the Inno Spot LED WiFly by ADJ Products LLC Every Inno Spot LED WiFly has been thoroughly tested and has been shipped in perfect operating condition Carefully check the shipping carton for damage that may have occurred during shipping If the carton appears to be damaged carefully inspect your fixture for any damage and be sure all equipment necessary to oper ate the unit has arrived intact In the event damage has been found or parts are missing please contact our toll free customer support number for further instructions Please do not return this unit to your dealer without contacting customer support first Introduction The Inno Spot LED WiFly is a ten channel DMX intel ligent moving head mini LED fixture The Inno Spot LED WiFly can operate as a stand alone fixture or in a Master Slave configuration The Inno Spot LED WiFly has three operating modes a sound active show mode DMX controlled This fixture is suitable for theaters studios retail stores and other similar locations For best results use fog or special effects smoke to enhance the beams projections Customer Support ADJ Products LLC provides a toll free cus tomer support line to provide help and to answer any question should you encounter problems during your set up or initial operation You may also visit us on the web at www adj com for any comments or suggestions Service H
18. he first fixture controlled by the controller could be the last fixture in the chain When a fixture is assigned a DMX address of 1 the DMX controller knows to send DATA assigned to address 1 to that unit no matter where it is located in the DMX chain Data Cable DMX Cable Requirements For DMX and Master Slave Operation The Inno Spot LED WiFly can be controlled via DMX 512 protocol The Inno Spot LED WiFly is a ten channel DMX unit The DMX address is set electronically using the controls on the front panel of the unit Your unit and your DMX controller require a approved t E A itt a A UJ l h a DMX 512 110 Ohm Data cable for data input and Figure 1 ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 7 Inno Spot LED WiFly Set Up data output Figure 1 We recommend Accu Cable DMX cables If you are making your own cables be sure to use standard 110 120 Ohm shielded cable This cable may be purchased at almost all professional sound and lighting stores Your cables should be made with a male and female XLR connector on either end of the cable Also remember that DMX cable must be daisy chained and cannot be split Notice Be sure to follow figures two and three when making your own cables Do not use the ground lug on the XLR connector Do not con nect the cable s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR s outer casing
19. len or liquid has been spilled into the appliance B The appliance has been exposed to rain or water C The appliance does not appear to operate normally or exhibits a marked change in performance CAUTION This unit like any wireless device is highly susceptible to static electricity Static electricity can severly damage the unit Before touching the antenna please ground discharge yourself ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 4 Inno Spot LED WiFly Installation When installing the unit the trussing or area of installation must be able to hold 10 times the weight without any deformation When installing the unit must be secured with a secondary safety attach ment e g an appropriate safety cable Never stand directly below the unit when mounting removing or servicing the unit Overhead mounting requires extensive experience including calculat ing working load limits installation material being used and perodic safety inspection of all installation material and unit If you lack these qualifications do not attempt the installation yourself These installaiton should be checked by a skilled person once a year O im The Inno Spot LED WiFly is fully operational in two different mounting positions hanging upside down from a ceiling or set on a flat level surface To avoid internal
20. luding possessions and territories It is the owner s responsibility to establish the date and place of purchase by acceptable evidence at the time service is sought B For warranty service you must obtain a Return Authorization number RA before sending back the product please contact ADJ Products LLC Service Department at 800 322 6337 Send the pro duct only to the ADJ Products LLC factory All shipping charges must be pre paid If the requested repairs or service including parts replacement are within the terms of this warranty ADJ Products LLC will pay return shipping charges only to a designated point within the United States If the entire instru ment is sent it must be shipped in it s original package No accessories should be shipped with the product If any accessories are shipped with the product ADJ Products LLC shall have no liability whatsoever for loss of or damage to any such accessories nor for the safe return thereof C This warranty is void if the serial number has been altered or removed if the product is modified in any manner which ADJ Products LLC concludes after inspection affects the reliability of the product if the product has been repaired or serviced by anyone other than the ADJ Products LLC factory unless prior written authorization was issued to purchaser by ADJ Products LLC if the product is damaged because not properly maintained as set forth in the instruction manual D This is not a servi
21. ours are Monday through Friday 8 00 a m to 4 30 p m Pacific Standard Time Voice 800 322 6337 Fax 323 582 2941 E mail Support adj com Warning To prevent or reduce the risk of electrical shock or fire do not expose this unit to rain or moisture Warning This may cause severe eye damage Avoid looking directly into the light source at all times CAUTION This unit like any wireless device is highly susceptible to static electricity Static electricity can severly damage the unit Before touching the antenna please ground discharge yourself ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 2 General Instructions Inno Spot LED WiFly To optimize the performance of this product please read these operating instructions carefully to familiarize yourself with the basic operations of this unit These instructions contain important safety information regarding the use and maintenance of this unit Please keep this manual with the unit for future reference Inno Spot LED WiFly e DMX 512 Protocol Compatible Ten DMX Channels 8 Colors White 6 Rotating Replaceable Gobos Spot 3 Operating Modes Sound Active Show Mode amp DMX Control Internal Microphone Digital Display for Address and Function Setting UC3 Controller Not Included 4 Preprogrammed Shows Features Inno Spot LED WiFly Warranty Registration The Inno Spot LED WiFly carries a 2 year 730 days limited warrant
22. required voltage for your unit Do not attempt to operate this unit if the power cord has been frayed or broken Do not attempt to remove or break off the ground prong from the electrical cord This prong is used to reduce the risk of electrical shock and fire in case of an internal short Disconnect from main power before making any type of connection Do not remove the cover under any conditions There are no user serviceable parts inside Never operate this unit when it s cover is removed Always be sure to mount this unit in an area that will allow proper ventilation Allow about 6 15cm between this device and a wall Do not attempt to operate this unit if it becomes damaged This unit is intended for indoor use only use of this product outdoors voids all warranties Always mount this unit in safe and stable matter Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at plugs convenience receptacles and the point where they exit from the appliance Cleaning The fixture should be cleaned only as recommended by the manufacturer See page 25 for cleaning details Heat This fixture should be situated away from heat sources such as radiators heat registers stoves or other appliances including amplifiers that produce heat The fixture should be serviced by qualified service personnel when A Objects have fal
23. ressly provided above and under no circumstances shall ADJ Products LLC be liable for any loss or damage direct or consequential arising out of the use of or inability to use this product This warranty is the only written warranty applicable to ADJ Products LLC Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published MANUFACTURER S LIMITED WARRANTY PERIODS e Lighting Products 1 year 365 days Limited Warranty Such as Special Effect Lighting Intelligent Lighting UV lighting Strobes Fog Machines Bubble Machines Mirror Balls Par Cans Trussing Lighting Stands etc excluding LED and lamps e Laser Products 90 Day Limited Warranty e L E D Products 2 year 730 days Limited Warranty excluding motors PCB boards and power supplies which have a 1 year 365 day Limited Warranty and batteries which have a 180 day limited warranty ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 27 Inno Spot LED WiFly Specifications Model Inno Spot LED WiFly Voltage 120v 60Hz or 230v 50Hz LED 1 x 50W LED Power Consumption 99W Dimensions 8 75 L x 8 W x 12 75 H 221mm x 202mm x 320mm 17 Degree Multiple 15 Lbs 6 8 kgs 2 Amp None 10 DMX Channels 8 White 6 Spot 23 8mm 0 2mm thickness 19mm viewable Sound Active Yes Working Position Any Safe Secure Position Warranty 2 Year 730 days Voltage is
24. t LED WiFly The ADJ Inno Spot LED WiFly is available in a switchable 120v and 220v version Because line voltage may vary from venue to venue you should be sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture Also be sure to only use the included E C power cable supplied with the unit this cable matches the voltage and current requirements of the unit DMX 512 DMX is short for Digital Multiplex This is a universal pro tocol used by most lighting and controller manufactures as a form of communication between intelligent fixtures and controllers A DMX controller sends DMX data instructions from the controller to the fix ture DMX data is sent as serial data that travels from fixture to fixture via the DATA IN and DATA OUT XLR terminals located on all DMX fixtures most controllers only have a DATA OUT terminal DMX Linking DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller as long as all fixtures and the controller are DMX compliant Jo ensure proper DMX data transmission when using several DMX fixtures try to use the shortest cable path possible The order in which fixtures are connected in a DMX line does not influence the DMX addressing For example a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line at the beginning at the end or anywhere in the middle Therefore t
25. thing is set up correctly the Master units signal strength will be displayed in the WiFly signal status window located on the rear of the unit NOTE If they do not sync up master slave switch the Master fix tures power off then on again ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 19 Inno Spot LED WiFly DMX Traits Value Function 0 255 540 PAN 0 255 270 TILT Inno Spot LED WiFly WiFly DMX Operation DMX Mode Your DMX controller must be connected to a ADJ WIFly TransCeiver sold separately Operating through a DMX controller gives the user the freedom to create their own programs tailored to their own individual needs You are able to communicate up to 400 feet open line of sight The Inno Spot LED WiFly has 10 DMX chan nels See pages 21 22 for the DMX traits 1 This function will allow you to control each individual fixture s traits with a standard DMX 512 controller 2 Torun your fixture in DMX mode press the MODE button until Addr is displayed and press ENTER The current address that 0 14 15 28 29 42 43 56 of 70 71 84 85 98 COLORS WHITE RED BLUE GREEN YELLOW PINK LIGHT BLUE is set will be displayed Use the UP or DOWN buttons to select your desired DMX address then press ENTER 3 After you have set your DMX address you need to set the WiFly address Follow the instructions on page 11 to set the Wireless address The address must match
26. until FADJ is displayed press ENTER The fixture will turn a different way each time the ENTER button is pressed 2 With the spot pointed at a flat wall or surface at the distance it will be set up you can turn the lens to adjust the clarity Press MENU to exit TEST This function will run a self test program The test program will test pan tilt movement and colors 1 Press the MENU button until TEST is displayed press ENTER 2 The fixture will now run a self test TEMP with this function you can check the temperature of the fixture 1 Press the MENU button until TEMP is displayed press ENTER 2 The temperature of the fixture will now be displayed Press MENU to exit FHRS with this function you can display the running time of the unit 1 Press the MENU button until FHRS is displayed press ENTER 2 The running time of the fixture will now be displayed Press MENU to exit ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 14 Inno Spot LED WiFly System Menu VER With this function you can display the version soft ware of the unit 1 Press the MENU button until VER is displayed press ENTER 2 The software version will now be displayed Press MENU to exit RSET use this function to reset the unit 1 Press the MENU button until RSET is displayed press ENTER 2 The fixture will now reset ADJ Products LLC www adj com Inno
27. user selectable Please Note Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice ADJ Products LLC 6122 S Eastern Ave Los Angeles CA 90040 USA Tel 323 582 2650 Fax 323 725 6100 Web www adj com E mail info americandj com A D J Supply Europe B V Junostraat 2 6468 EW Kerkrade Netherlands service adjgroup eu www adj eu Follow Us On t facebook com americandj twitter com americandj youtube com adjlighting Tel 31 45 546 85 OO Fax 31 45 546 85 99
28. y Please fill out the enclosed warranty card to validate your purchase and warranty You may also register your product online at www adj products com All returned service items whether under warranty or not must be freight pre paid and accompany a return authorization R A number If the unit is under warranty you must provide a copy of your proof of purchase invoice Please contact ADJ Products LLC customer support for a R A number Inno Spot LED WiFly Caution There are no user serviceable parts inside this unit Do not attempt any repairs yourself doing so will void your manufactures warranty In the unlikely event your unit may require service please contact ADJ Products LLC During operation the housing may become extremely hot Avoid touching the unit with bare hands while in use Handling Precautions ADJ Products LLC will not accept any liability for any resulting dam ages caused by the non observance of this manual or any unauthor ized modification to this unit ADJ Products LLC www adj com Inno Spot LED WiFly Instruction Manual Page 3 Inno Spot LED WiFly Safety Precautions For Your Own Personal Safety Please Read and Understand This Manual Completely Before You Attempt To Install Or Operate This Unit To reduce the risk of electrical shock or fire do not expose this unit rain or moisture Do not spill water or other liquids into or on to your unit Be sure that the local power outlet match that of the
Download Pdf Manuals
Related Search