User manual - Vandenborre
Contents
1. Using headphones at a high volume can impair your hearing This product can produce sounds in decibel ranges that may cause hearing loss for a normal person even for exposure less than a minute The higher decibel ranges are offered for those that may have already experienced some hearing loss e Sound can be deceiving Over time your hearing comfort level adapts to higher volumes of sound So after prolonged listening what sounds normal can actually be loud and harmful to your hearing To guard against this set your volume to a safe level before your hearing adapts and leave it there To establish a safe volume level e Set your volume control at a low setting Slowly increase the sound until you can hear it comfortably and clearly without distortion Listen for reasonable periods of time e Prolonged exposure to sound even at normally safe levels can also cause hearing loss e Be sure to use your equipment reasonably and take appropriate breaks Be sure to observe the following guidelines when using your headphones e Listen at reasonable volumes for reasonable periods of time e Be careful not to adjust the volume as your hearing adapts e Do not turn up the volume so high that you can t hear what s around you e You should use caution or temporarily discontinue use in potentially hazardous situations o o Notice KN D Cy Any changes or modifications e to this device t2. from the Bonjour pull down list shown at the bookmarks bar L The configuration web page is displayed to connect ycur wireless ie by modifying the Yahoo Goa ips Fidelio oGEF About Bonjour Philips_DCW8010 sswerd if z Click Apply to ect Uptor Ee marepat arr woore ONO MIN miiie Palp Riecrenice UV Mirgi imanad CORR 4 7811 Frink ite Ihi ips Electrix AV Airiga encnevec Change the internal Wi Fi settings of this system On the configuration web page of this system you can change the internal Wi Fi settings for connection of this system to your existing home Wi Fi network Note e Make sure that the settings on the configuration web page match your home Wi Fi network settings that you wrote down on paper e Ifthe LED indicator in the middle amp f WIFI SETUP button does not stay solid green an that the Wi Fi connection has failed Reboot y uR Wi Fi router and this system and then check whether thts system is connected to your Wi Fi network If the prdplem remains try the above procedures again J After you finish the above changes or reboot this system the new Wi Fi network created by this syster A disappears 102 108 1 1 CE coo Philips Fidelio Pd Welcome to Philips Fidelio setup page Follow the steps below to conmect your wireless speaker to your wireless network You can keep the default device nam or modify the device name by modifyin
3. lt 0 5 W tion at eco power standby mode Dimensions O SUG a Amm Net weight 3 1 kg USB playability information Compatible USB devices USB flash memory USB 2 0 or USB1 1 USB flash players USB 2 0 or USB1 1 memory cards requires an additional card reader to work with this unit Supported formats USB or memory file format FAT12 FAT16 FAT 32 sector size 512 bytes MP3 bit rate data rate 32 320 Kbps and variable bit rate WMA v9 or earlier Directory nesting up to a maximum of 8 levels Number of albums folders maximum 29 Number of tracks titles maximum 999 ID3 tag v2 0 or later File name in Unicode UTF8 maximum length 128 bytes Unsupported formats Empty albums an empty album is an album that does not contain MP3 WMA files and will not be shown in the display Unsupported file formats are skipped For example Word documents doc or MP3 files with extension dlf are ignored and not played AAC WAV PCM audio files DRM protected WMA files wav m4a M4p Mp4 aac WMA files in Lossless format Supported MP3 disc formats ISO9660 Joliet e Maximum title number 512 depending on file name length e Maximum album number 255 e Supported sampling frequencies 32 kHz 44 1kHz 48 kHz Qo Lb Y Supported Bit r Es 32 256 kbps variable bit rates amp Pys fo RDS program types NO TYPE No RDS programme typ amp gt NEWS News services AFFAIRS
4. 66 EC which cannot be disposed with normal household waste Please inform yourself about the local rules on separate collection of batteries because correct disposal helps to prevent negative consequences for the environmental and human health h Environmental inforiMatjon All unnecessary packag s been omitted We have tried to make the Rekaging easy to separate into three materials i box polystyrene foam buffer and poly amp thylene bags protective foam sheet Your system consists of materials which be recycled and reused if disassembled by Uy a specialized company Please observe the By local regulations regarding the disposal of es packaging materials exhausted batteries and old S 3 equipment Q Information about the use of batteries EE Caution e Risk of leakage Only use the specified type of batteries Do not mix new and used batteries Do not mix different brands of batteries Observe correct polarity Remove batteries from products that are not in use for a longer period of time Store batteries in a dry place e Risk of injury Wear gloves when handling leaking batteries Keep batteries out of reach of children and pets e Risk of explosion Do not short circuit batteries Do not expose batteries to excessive heat Do not throw batteries into the fire Do not damage or disassemble batteries Do not recharge non rechargeable batteries e Risk of swallowing batteries The product remote control may contain
5. PRESET ALBUM A Vv e Skip to the previous ee album e Select a preset radio station e Navigate through Pod iPhon laylist 1d gt gt I Tia e Skip to the previous or next track e Press and hold to search within a track h e Tune to a radio station A USB e Switch the source to USB storage device RDS DISPLAY e Synchronize the clock with an RDS radio station that transmits time signals e Display the current status or media information K e Mute or restore volume PROG CLOCK e Program radio stations Set the clock SLEEP SNOOZE Set the sleep timer or alarm timer SOUND e Access the sound setting for DSC DBB and full sound control SETTINGS e Access the menu of system settings REPEAT SHUFFLE Select a play mode Numeric keypad VOL e Increase or decrease the volume level E MENU e Stop the play of music e Access the playlist of iPod iPhone 7 DOCKING e Switch the source to the audio input that is transferred through the dock gt Il e Start pause or resume play TUNER MP3 LINK e Switch the source between FM tuner or the audio input that is transferred through the MP3 LINK socket EN ji 3 Before use Connect the FM antenna Note e For optimal reception fully extend the antenna and adjust its position or connect an outdoor antenna e This product does not support MW medium wave radio reception Connect the FM antenna to th
6. Politics and current affairs INFO Special information programs i SPORT Sports Orn EDUC iE Education and advanced training DRAMA Radio plays and literature COMORE Culture religion and society SCIENCE Science VARIED Entertainment programs POP M Pop music ROC M Rock music MORM Light music LETEM Light classical music CLASSICS Classical music Cale M Special music programs WEATHER Weather FINANCE Finance CHILDREN Children s programs SOCIAL Social Affairs RELIGION Religion PHONE IN Phone In TRAVEL Travel LEISURE Leisure JAZZ Jazz Music COUNTRY Country Music NATION M National Music OLDIES Oldies Music POLI M Folk Music DOCUMENT Documentary ies Alarm Test ALARM Alarm EN 41 O Lb 15 Troubleshooting Ts Dy Warning D T Le e Never remove the casing of this product PI K To keep the warranty valid never try to repair the product yourself G If you encounter problems when using this product check the following points before requesting O service lf the problem remains unsolved go to the Philips Web page www philips com support When ve you contact Philips make sure that the product is nearby and the model number and serial number are On available Problem S70 01 1101 No power Make sure that the power adaptor is securely connected to both the power supply and the CD sound machine Make sure that there is power at the AC outlet No sound or poor sound Adjust the volume Disconnect
7. keypad Display RDS information RDS Radio Data System Is a service that allows FM stations to show additional information 1 Tune to an RDS radio station 2 Press DISPLAY RDS repeatedly to scroll through available information e Station name e Program type such as NEWS news SPORT sport POP M pop music e Text messages RDS clock e Frequency Synchronize clock with RDS You can synchronize system clock with an RDS radio station 1 Tune to an RDS radio station that transmits time signals 2 Press and hold DISPLAY RDS until CT SYNC is displayed L gt The system reads RDS time automatically L gt If no time signal is received NO CT is displayed Note e The accuracy of the clock depends on the RDS radio station EN 31 9 Play Play a disc Caution e Never insert any object other than a disc of 12 cm diameter into the disc compartment 1 Press SOURCE repeatedly to switch the source to DISC e You can also press CD to switch the source 2 Insert a disc into the disc compartment with the printed side facing you L Play starts automatically after a few seconds e If play does not start automatically Press P H to start play 32 EN O Play from a US amp storage device li O This system can play mp3 and write files that are copied onto a supported USB stongge device Q or Flash drive e Memory card reader Z O ly e HD
8. press gt gt I between this system and your home WI FI network IP ADDR Display the IP address of this system in Select IP ADDR and then press gt PL your home Wi Fi network DIMMER Select a brightness level of VFD screen 1 Select DIMMER and then press PL 2 Press amp W to select a bright level NET RST Reset the network connection 1 Select NET RST 2 Press PI twice to start resetting FAC RST Reset this system to factory default 1 Select FAC RST settings 2 Press PI twice to start resetting VERSION Display the firmware version 1 Select VERSION and then press PL 2 Press amp W to select a version name 3 Press BPI to display the current version EN 3 7 2 13 Update Update the firfaware from firmware the configuration page O Warning h To improve the performance of this system e Make sure that the power is not interrupted ung firmware upgrade Philips may offer you new firmware for upgrade Qo Please register your product at www philips 7 com welcome for information about the latest Note firmware e f you use an internet browser other than Apple Safari E on your PC Mac remember to go to the Wi Fi router md Note configuration page and write down the IP address of this system See the user manual of your Wi Fi router e You can update the firmware with a PC Mac only for how to find the IP addresses of devices that are connected to the Wi Fi router 1 Power on this system see T
9. the headphones Make sure that you have select the correct audio source If you select audio input by AirPlay as the source make sure that the host is not muted this system Is selected as the AirPlay target receiver on your host the network connection between the host and your Wi Fi router Is available and e the Wi Fi connection between this system and your WI FI router is available No response from the system Reconnect the power adaptor and wait about 35 seconds for this system to boot up Remote control does not Before you press any function button select the correct source with work the remote control instead of the main unit Reduce the distance between the remote control and the main unit Insert each battery with rts polarity signs aligned as indicated Replace the batteries Aim the remote control directly at the sensor on the front panel of the main unit No disc is detected Insert a disc of 12 cm diameter never one of other sizes Make sure that the label of the disc faces you Wart until the moisture condensation at the lens is cleared Replace or clean the disc Make sure that the recordable disc is finalized and the format supported USB storage device is not Make sure that the USB storage device is compatible with the system supported Try another one 42 EN h Q Problem Syo Ululela Cannot play some files on the Make sure that the file format is supported USB aor ee Cleves Make sure th
10. to your existing home Wi Fi setting list of available wire etworks vs settings Wi Fi Networks ote e Make sure that the settings at steps 2 to 3 below match your home Wi Fi network settings you wrote on paper 1 Select Settings gt Wi Fi on your iPod touch iPhone iPad e Or open the list of available Wi Fi networks on your PC Mac J oa y az Settings a Other gt S al Airplane Mode a Ask to Join Networks OW Wi Fi e Ea gt Known networks will be joined automatically If no known networks are Off gt 3 Enter the network key if required Carrier gt 4 Wait until successful Wi Fi connection to your home Wi Fi network BJ Brightness Wallpaper g gt General 24 EN 6 Stream audio by AirPlay Stream audio from your iTunes music library Note e Make sure that your iTunes host device is connected to the same Wi Fi network as this system Your iTunes device can be an iPod touch iPhone iPad installed with IOS 4 3 or later or a Wi Fi enabled PC Mac installed with iTunes 10 or later For iPhone 4S users To ensure optimal performance of AirPlay streaming upgrade your iPhone 4S to iOS 5 1 or later Stream from your iPod touch iPhone iPad 1 Launch the iPod Music application on your iPod touch iPhone iPad 2 Tap on the AirPlay icon 4a Symphony No 9 Scherzo O 3 Select Philips D W8010 XXXXXX or
11. D hard disc drive This product can detect only a portable HDD with USB power peak current no more than 500 mA e Philips does not guarantee compatibility with all USB storage devices e NTFS New Technology File System file system is not supported 1 Connect the USB storage device to the lt gt socket 2 Press SOURCE repeatedly to switch the source to USB e You can also press USB to switch the source L gt Play starts automatically If play does not start automatically 1 Press A W to select a folder 2 Press I4 PPI to select a file 3 Press PAN to start play S o Control play Ke Q 6 During play follow the instructions below to control play K gt il Pause or resume play h E Stop play area a a a a 00 lt lt gt i Skip to the previous or next track 2 Press and hold to rewind a track or search forward fast within a track z A V Skip to the previous or next album when one or more album exit CA C1 Enter the number of a track to play tt BD E a REPEAT SHUFFLE Select an available play mode e RPT 1 repeat the current track e RPT ALL repeat all tracks e SHUFFLE press and hold to play tracks randomly e NORMAL play tracks in sequence EN 33 10 Other features Set alarm timer You can use this system as an alarm clock Note e Make sure that you have set the clock correctly 1 In normal standby mode press and hold SLEEP SNOOZE until DISC blinks 2 Press 4
12. I FI enabled device see Open the built in web page of this system on page 22 h E a Change the intera Wi Fi settings of this system based on theeegstings that you wrote down on paper aggtep 1 see Change the internal Wi Fidgettings of this system on page 23 DS Restore your Wi Fi enabled devic amp back to your existing home Wi Fi settings gee Restore your Wi Fi enabled device Dato to your existing home Wi Fi setting on Q router page 24 h o 2 Collect settings of your home Wi Fi Note e Always consult the user manual of your home Wi Fi router for detailed instructions Connect your Wi Fi enabled device to your existing home Wi Fi network Launch the Internet browser for example Apple Safari or Microsoft Internet Explorer on your WI Fi enabled device Open the configuration page of your home WI FI router Find the WI FI settings tab and write down the following information on paper A Network name SSID Wi Fi security mode usually WEP WPA or WPAZ if enabled C Wi Fi password if Wi Fi security is enabled D DHCP mode enabled or disabled E Static IP address settings if DHCP mode is disabled EN 19 Switch this system to Assisted Wi Fi Setup mode Note e Before you press any button on the main unit make sure that the system has been booted up successfully see Turn on on page 16 Press WIFI SETUP on the top panel L The LED indicator in
13. O a i O Register your product and get support at Oa 7 Q www philips com welcome KN 3G W8010 ep K User manual PHILIPS Contents Important Safety Notice Your wireless music system with AirPlay Introduction What s in the box What else you need Overview of the main unit Overview of the remote control Before use Connect the FM antenna Connect power Install replace the remote control batteries Get started Turn on Switch modes Set the clock Connect to your home Wi Fi network Method 1 Use IOS 5 Wi Fi network login sharing Method 2 Connect to a WPS router Method 3 Connect to a non WPS router Stream audio by AirPlay Stream audio from your iTunes music library Control play Use advanced sound settings Use the dock Compatible Pod iPhone iPad models Enjoy audio through the dock Charge your Pod iPhone iPad Undock your iPod iPhone N A N O V O CO OO 14 14 14 16 16 16 16 17 17 18 17 D 25 2 2y 28 28 28 27 29 or 8 Listen to FM radio 7 by 30 Tune to an FM radio station 30 Program radio stations wie p 30 Program radio stations manually I 30 Tune to a preset radio station Display RDS information 9 Play Play a disc Play from a USB storage device Control play 10 Other features Set alarm timer Set sleep timer Listen to an external audio device Listen through headphone 11 Adjust sound Adjust volume level Mute sound Ad
14. Press PROG CLOCK to confirm the clock setting L gt The set clock is displayed Ea e You can also synchronize the system clock with an RDS radio station that transmits time signals Refer to Listen to FM radio gt Display RDS information gt Synchronize clock with RDS 5 Connect to your home Wi Fi network To connect this system to your existing home Wi Fi network you need to apply your home WI FI settings to tt Choose your best setup method based on the preconditions listed below Precondition Setup method You have an iPod touch Method 1 iPhone iPad upgraded recommended ton gt 0 ror laren see Memo Use IOS 5 Wi Fi network login sharing on page 17 Your Wi Fi router is Method 2 see enabled with VVPS Method 2 Connect Wi Fi Protected Setup to a WPS router on and supports PBC Push page 18 Button Connection You have a WI Fi enabled device with an Internet browser such as an IPod touch iPhone iPad or a Wi Fi enabled PC Mac Kemod iee Manod TOE to a non VWPS router on page 19 KN A Before you connect this system to you home Wi Fi network make s that e your WI FI router is pows red on and working properly e this system has been powered on and booted up successfully see Turn on page 16 h Once connected successfully this system Wo remember your home Wi FI settings Whenev amp e gt this system Is powered on it connects to your h home Wi Fi netwo
15. a coin type battery which can be swallowed Keep the battery out of reach of children at all times Trademark notice Made for iPod Q iPhone iPad Lad AirPlay Made for iPod Made for iPhone and Made for iPad mean that an electronic accessory has been designed to connect specifically to iPod IPhone or iPad respectively and has been certified by the developer to meet Apple performance standards Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards Please note that the use of this accessory with iPod iPhone or iPad may affect wireless performance AirPlay iPod and iPhone are trademarks of Apple Inc registered in the U S and other countries iPad is a trademark of Apple Inc CERTIFIED The Wi Fi CERTIFIED Logo is a certification mark of the Wi Fi Alliance Copyright The making of unauthorized copies of copy protected material including computer programs files broadcasts and sound recordings may be an infringement of copyrights and constitute a criminal offence This equipment should not be used for such purposes 2012 Koninklijke Philips Electronics N V Specifications are subject to change without notice Trademarks are the property of Koninklijke Philips Electronics N V or their respective owners Phillps reserves the right to change products at any time without being obliged to adjust earlier supp
16. at the file quantity does not exceed th maximum Radio reception Is poor Increase the distance between the system and other electrical appliances Fully extend the antenna and adjust its position F Connect an outdoor FM antenna instead EE SR Timer does not work Set the clock correctly 2i Switch on the timer K O Q Clock timer setting is erased Power is interrupted or cut off Reset the clock timer Wi Fi network connection Check whether your Wi Fi router is Wi Fi 802 11b g certified This failed device is only compatible with Wi Fi 802 11b g certified routers If your Wi Fi router is Wi Fi 802 11n certified make sure to enable the 802 11b g mode This system does not support connection to routers with 802 11n only This system does not support the WPS PIN method If your Wi Fi router supports WPS and the WPS PBC method but fails to connect to this system try the other Wi Fi setup methods indicated in this user manual see Method 3 Connect to a non VWVPS router on page 19 Enable SSID broadcast on the Wi Fi router Keep away from potential sources of interference which may affect WI FI signal such as microwave ovens If you fail to use your PC for Wi Fi network setup check whether your PC is using a Wi Fi network You cannot use Ethernet Wi Fi connection for AirPlay network setup make sure that the SSID name of your home router consists of alphanumeric characters with no space or special characters like oR ins
17. d DDI repeatedly to select an alarm source 3 Press SLEEP SNOOZE to confirm L gt The hour digits blink A Press I lt BPI repeatedly to set the hour digits and then press SLEEP SNOOZE to confirm L gt The minute digits blink 5 Press I4 BPI to set the minute digits and then press SLEEP SNOOZE to confirm L gt A alarm and the current time is displayed e To check the alarm time press SLEEP SNOOZE in normal standby mode e lo deactivate the alarm timer press SLEEP SNOOZE repeatedly in normal standby mode until A alarm disappears e To re activate the alarm timer press SLEEP SNOOZE repeatedly in normal standby mode until A alarm is displayed e To pause the alarm press SLEEP SNOOZE once After five minutes the alarm sounds again e To stop the alarm press and hold SLEEP SNOOZE until ALM STOP is displayed 34 EN e you can set the hour minute iseSby the numeric keypad O Set sleep timer KA In working mode press SLEEP SNOOZE KA repeatedly to select a preset period 30 60 90 6 or 120 minutes i e To deactivate the sleep timer press SLEEP SNOOZE repeatedly until SLEEPOFF is displayed Listen to an external audio device You can listen to an external audio device for example MP3 player through this product 1 Press TUNER MP3 LINK repeatedly to switch the source to MP3 LINK 2 Connect an MP3 Link cable to e the MP3 LINK socket on the top
18. e FM ANT socket on the back panel Connect power Caution e Risk of product damage Make sure that the power supply voltage matches the voltage printed on the back of the main unit e Risk of electric shock Before you plug the AC power adaptor make sure that the adaptor plug converter Is fixed securely When you unplug the AC power adaptor always pull the plug never the cord e Before you connect the AC power adaptor make sure that you have completed all the other connections 14 EN Q L Q 1 Selecta ac glial and fix it to the adaptor amp 2 Connect the AC power adaptor to e the DC IN socket on the back panel and e the wall outlet Install replace the remote control batteries Caution e Risk of explosion Keep batteries away from heat sunshine or fire Never discard batteries in fire 1 Open the battery compartment 2 Insert 2 AAA batteries with correct polarity as indicated an 3 Close the battery compartment e Before you press any function button on the remote control first select the correct source with the remote control instead of the main unit If you do not use the remote control in a coming long time remove the batteries For better reception point the remote control directly at the IR sensor on the front of the main unit EN 15 4 Get started Caution e Use of controls or adjustments or performance of procedures other than
19. e Skip to the previous or next track e Press and hold to search within a track e Tune to a radio station VOL VOL e Increase or decrease the volume level Dock for iPod iPhone iPad e Connect to a compatible iPod iPhone iPad IR sensor e Receive infrared signals from the remote control VFD screen MP3 LINK e Connect to the audio output socket usually the headphone socket of an external device WIFI SETUP e Press to activate the setup of connection to a non WPS router or an iPod touch iPhone iPad with iOS 5 x e Press to activate the setup of connection to a WPS router Q Lb om e To change a setup after first time setup press an Id WIFI SETUP for more than 3 ea reset WI Fi settings K p e Connect to a USB storage delfe 45 N K e Connect to a headphone with 3 5 mog connector h DC IN 6 Q e Connect to the AC power adaptor 17 Wi Fi antenna e Fix the Wi Fi antenna to the main unit for better emission and reception of WI FI signals FM ANT e Connect to the FM antenna EN 11 Overview of the remote control TUNER MP3 LINK oe eee 2 PHILIPS O e urn on the system e Switch the system to eco power standby mode or normal standby mode 2 AirPlay e Switch the source to audio input that is streamed from your i lunes library by AirPlay 12 EN O OO p CD oe e Switch the ke disc
20. erted If you renamed the AirPlay device Philips DCW8010 XXXXXX in the setting menu do not use special characters or symbols For some new types of Wi Fi routers a network name SSID may be created automatically when you use WPS for connection Always change the default network name SSID to a simple one that consists of alphanumeric characters and also change the Wi Fi security mode to secure your network EN 43 O to Occasional breaking of AirPlay Do one or all of the following i Q music streaming e Move this system closer to your Wi Fi router e Keep the space between this system and your Wi Fi opter clear of any obstacle PA Do not use Wi Fi channel that is overlapped by the nearby VIFF network e Check whether your network speed is fast enough in cases el multiple devices share the same router the AirPlay performance O may be affected Turn off the other devices connected to your K home router On Enable the Quality of Service QoS option if available on the Wi Fi router e Turn off other Wi Fi routers No AirPlay icon on my Tunes Make sure that this system Is already connected to your home Wi Fi host device network Before you open iTunes make sure that you have enabled Bonjour service in your PC Take Windows XP for example to enable the service click Start gt Control Panel and double click Administrative Tools gt Services gt Bonjour Service and then click Start followed by OK on the pop u
21. fully Tip e For some Wi Fi routers you need to hold the WPS button for Wi Fi connection or enable the WPS PBC function from the router configuration pages See the user manuals of the specific routers for details If the WIFI SETUP indicator on DCW 8010 stays yellow it means that the Wi Fi connection has failed Please wait for 2 minutes and try again If the problem remains try to set up the Wi Fi connection manually e lf the Wi Fi connection fails again reconnect the power adaptor and then try again Method 3 Connect to a non WPS router To connect this system to a non WPS Wi Fi router with a PC Mac or iOS 4 3 iPod touch iPhone iPad you need to access Its built in configuration web page to change its internal WI FI settings Follow the steps below to complete the connection 1 Collect settings of your home Wi Fi router and write down on paper for use see Collect settings of your home Wi Fi router on page 19 2 Switch this system to Assisted Wi Fi Setup mode see Switch this system to Assisted Wi Fi Setup mode on page 20 L gt Anew WI FI network is created by this system with the network name SSID of Philips DCW8010 XXXXXxX 3 Connect your WI FI enabled device to the created new Wi Fi network temporarily see Connect your Wi Fi enabled device to the newly created Wi Fi network on page 20 4 Open the built in web page of this system with the internet browser of your W
22. g the text in the text box Click Apply to proceed with device name change Philips Fidelio device name Philios_ Fidelio FAFA Please select your wireless network and enter your network password if applicable For advanced network setup please click Advanced Click Apply to connect your wireless speaker to your network Please select your Wi Fi network Select Option A lt ea ee e Follow the on screen instructions to change and confirm the internal Wi Fi settings L After a while the indicator in the middle of WIFI SETUP button stops blinking and stays solid green and the main unit beeps L gt This system is connected to your existing home Wi Fi network successfully Tip Q If you like you can change the device name of this system in Advanced settings gt AirPlay Device Name on its configuration web page This is helpful for you to distinguish this system from other Philips AirPlay enabled devices in your house If you want to enter the network name SSID manually for example If you want to hide your SSID go to Advanced settings gt CONFIGURE MANUALLY on the configuration web page of this system To change Wi Fi setup after first time setup press and hold WIFI SETUP for more than 3 seconds to reset the WiA Fi setting Then follow the previous steps to change your network settings EN 23 O L e z Restore your Wi Fi enabled device back 2 Select your netwek name SSID from the
23. hat are not expressly apprdyed by Philips Consumer Lifestyle may void users authority to operate the equipment K o Z Compliance KA O Q C This product complies with the radio interference requirements of the European Community BG RO V pe Vit Jlu slis se V EE iT slu vje YicH o The device can be operated in the EU without restrictions indoor but cannot be operated outdoors in France in the whole of the band until further notice This product complies with the requirement of the 1999 5 EC directive This apparatus includes this label CLASS 1 LASER PRODUCT EN 5 Class Il equipment symbol CLASS II apparatus with double insulation and no protective earth provided Care of the environment ao Your product is designed and manufactured with high quality materials and components which can be recycled and reused R When this crossed out wheeled bin symbol is attached to a product it means that the product is covered by the European Directive 2002 96 ae Please inform yourself about the local separate collection system for electrical and electronic products Please act according to your local rules and do not dispose of your old products with your normal household waste Correct disposal of your old product helps to prevent potential negative consequences for the environment and human health R Your product contains batteries covered by the European Directive 2006
24. herein may result in hazardous radiation exposure or other unsafe operation Turn on After proper power connection the system switches on automatically Wart for successful boot up of the unit L The boot up takes up to 35 seconds L gt During boot up the LED indicator in the middle of the WIFI SETUP button blinks yellow L gt After boot up If no Wi Fi connection has been set up for this system the LED indicator stays solid yellow Switch modes Manually switch the modes e Press and hold to switch this system to eco power standby mode e Press to switch this system e from working mode to normal standby mode or e from eco power standby mode to working mode 16 EN Set the clock KN 6 Note Q e During setting if no action is made within I seconds the system exits clock setting without saving Ealier operations D In normal standby mode press PROG KA CLOCK to activate the clock setting O L gt 24HOUR 24 hour time format blinks On 2 Press I4 BPI to select 244HOUR or 12HOUR 12 hour time format and then press PROG CLOCK to confirm L gt The hour digits blink L gt If you select 12HOUR as the time format PM or AM is displayed 3 Press Idd DDI repeatedly to set the hour digits e You can enter the digits with the numeric keypad 4 Press PROG CLOCK to confirm L gt The minute digits blink 5 Press Idd DDI repeatedly to set the minute digits 6
25. just default sound settings 12 Adjust system settings 13 Update firmware Download the update file Update the firmware from the configuration page 14 Product information Specifications USB playability information Supported MP3 disc formats RDS program types 15 Troubleshooting EN 3 oy 32 22 33 34 24 a 34 35 36 36 36 36 a 38 38 38 40 40 41 41 te 1 Important Safety Information for Europe Know these safety symbols A CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER OR BACK NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation mark calls attention to features for which you should carefully read the supplied literature to prevent operating and maintenance problems The lightening bolt symbol indicates uninsulated components within the product that can cause an electric shock To reduce the risk of fire or electric shock do not expose the product to rain or moisture and do not place any objects filled with liquids such as vases on the product Read these instructions Keep these instructions Heed all warnings Follow all instructions Do not use this product near water Clean only with dry cloth SIOIOLO TO TOS Do not block any ventilation openings Install in accordance with the manufacturer s instructions N EN Do n
26. lies accordingly Note e The type plate is located on the back of the system EN 2 Your wireless music system with AirPlay Congratulations on your purchase and welcome to Philips To fully benefit trom the support that Philips offers register your product at www philips com welcome If you contact Philips you will be asked for the model and serial number of this product The model number and serial number are on the back of the main unit Write the numbers here Model No Serial No Introduction With this system you can e enjoy audio from discs USB storage devices IPod iPhone iPad and other external devices e listen to FM radio stations e charge your Pod iPhone iPad directly e stream audio from an iTunes music library that is hosted on a Mac PC iPhone iPod touch or iPad by AirPlay You can enrich sound output with these sound effects e Digital sound control DSC e Dynamic bass boost DBB e Full sound control Playable media Discs Audio CD CD R CD RW MP3 CD WMA CD e USB storage device e Compatibility USB 1 1 USB2 0 e Class support MSC Mass Storage Class e File system FAT12 FAT16 FAT 32 e Files mp3 wma K e Maximum Naper of albums folders 99 Q e Maximum number eftracks files 999 e Maximum level of dire agry 8 e iPod iPhone and iPad models e iPad 2 and iPad Lb e iPhone 4S iPhone 4 iPhone Gand iPhone 3G Uy iPod touch 1
27. lips DCW8010 XXXXXX from the list of available networks Settings O E 3 Wait until successful Wi Fi connection on 3 Select Philips Deys010 XXXXXX from your IPod touch iPhone iPad the list of available Ketyorks A is displayed at the upper left corner of your IPod touch iPhone iPad Wircless Network Connection Tip If Philips DCW8010 XXXXXxX is not in the list try to scan the available Wi Fi networks again Option 2 Use your Wi Fi enabled PC Mac See the user manual of your PC Mac for how to i anedya PCIMAe 1a ai Fine work 4 Wait until successful Wi Fi connection on During Wi Fi network connection do not connect any your PC Mac network cable to your PC Mac Wireless Network Connectio F be 1 Open the Wi Fi setup tool or control Sloman ioceena panel on your PC Mac 2 Scan the available Wi Fi networks th Set up a vaneless netveerk fora or ead office Belated Tasks neteding Change the coder of ee aera aes pe Change atvanced cetera Tip e If Philips DCW8010 XXXXXxX is not in the list try to scan the available Wi Fi networks again EN 21 Open the built in web page of this system 1 Launch Apple Safari browser or any other internet browser on your Wi Fi enabled device 2 Type in 192 168 1 1 at the browser address bar and confirm L The configuration web page is displayed Philips Fidelio Welcome to Philips Fidel steps below to connect you
28. o your a home Wi Fi network on page 17 EN 39 14 Product information Note e Product information is subject to change without prior notice Specifications Amplifier Rated output power 40 W 60 Hz 20 kHz 3 dB gt 7 5 dB 1 000 mV RMS Frequency response Signal to noise ratio KESAN ayer Disc Laser type Semiconductor Disc diameter een Support discs Audio CD CD R CD RW MP3 CD WMA CD Audio DAC EY Tene fase 2 Total harmonic lt 1 distortion Tuner Tuning Range FM 87 5 108 MHz Tuning grid 50 Naz Sensitivity Mono 26dB S N Ratio lt 22 dBu Stereo 46dB S N lt 45 dBu Ratio Search Selectivity lt 30 dBu Total Harmonic lt 3 Distortion Signal to Noise Ratio oe 40 EN O Speakers oy Speaker Impedance 8 Kom 2 X 2 5 full range Speaker Driver speaker Sensitivity gt 82 dB m W E Wireless KA Wireless standard 80211b g Wireless security WIEBE ar Ole 2 ome On WPA WPA2 8 63 characters Frequency range 2412 2462 MHz CH1 CT Ors 7 437155 21 2412 24 72 MHz CH1 CH13 for 12 10 O5 PBC one button Yes push General 100 240 V 50 60 Hz 2 0 A Output of AC DC 18 0V 2 8 A power adaptor Model No of AC EFS05001800280CE DC power adaptor Trademark of AC T PHILIPS DC power adaptor AC power input Operation power 25 W consumption Power consump lt 6W tion at standby mode Power consump
29. one 3GS and iPhone 3G iPod touch 1st 2nd 3rd and 4th generations e iPod nano 2nd 3rd 4th 5th and 6th generations Enjoy audio through the dock Note e The peak current through the dock connector is limited as 1 000 mA for iPod iPhone and 2 100 mA for iPad iPad 2 To avoid damage to your iPod iPhone iPad and this system securely load your iPod iPhone iPad as indicated 1 Press SOURCE repeatedly to switch the source to iPod_iPhone_ iPad e You can also press DOCKING to switch the source 28 EN 3 Connect your Pod iPhone iPad to the dock 4 Play a track on your iPod iPhone iPad Buttons Functions gt il Start pause or resume play MENU M Access the playlist of iPod iPhone A V Navigate through the playlist of iPod iPhone la PPI Skip to the previous next track Press and hold to rewind or search forward fast Charge your iPod iPhone iPad Once the Pod iPhone iPad is docked and recognized the charging starts Undock your iPod iPhone Note e Risk of damage to the dock or your iPod iPhone Do not twist or shake your iPod iPhone iPad d Pull the iPod iPhone iPad out of the dock 2 Push the dock tray inwards until you hear a click to store it L K Y O Ce EN 29 8 Listen to FM radio Tune to an FM radio station Note e Make sure that you have connected and fully extended the FM antenna d Press SOURCE or TUNER MP3 LINK re
30. ot remove the casing of this product Q he Only use this res indoors Do not expose the produ to dripping splashing water rain o Cig humidity Keep this product away ren direct sunlight naked flames or heat gt Do not install near any heat sources such as radiators heat registers stove or other electrical equipment including amplifiers Lp Do not place any other electrical On equipment on the product Do not place any sources of danger on the product e g objects containing liquids burning candles This product may include batteries Please refer to safety and disposal instructions for batteries in this user manual Where the mains plug or an appliance coupler is used as the disconnect device the disconnect device shall remain readily operable Warning Never remove the casing of this apparatus Never lubricate any part of this apparatus Never place this apparatus on other electrical equipment Keep this apparatus away from direct sunlight naked flames or heat Ensure that you always have easy access to the power cord plug or adaptor to disconnect this apparatus from the power Risk of overheating Never install this apparatus in a confined space Always leave a space of at least four inches around this apparatus for ventilation Ensure curtains or other objects never cover the ventilation slots on this apparatus Hearing safety Listen at a moderate volume e
31. p menu If the problem remains try to restart this system AirPlay connection failed with Temporarily disable the firewall and security software to see whether Mac or PC is blocks the ports that AirPlay uses to stream content See the help documentation of your firewall and security software on how to unblock the ports used by AirPlay When you use Pod touch iPhone iPad Mac PC for AirPlay if the music play breaks or stops try to restart your IPod touch iPhone iPad iTunes or this system Video streaming or FIP downloads may overload your router and therefore may cause Interruptions during AirPlay music play Try to reduce the load your router 44 EN Specifications are subject to change without notice 2012 Koninklijke Philips Electronics N V All rights reserved DCWs8010 10 UM V1 3 PHILIPS
32. panel of the system and e the headphone socket on the external device for example MP3 player 3 Play the external device See the user manual of external device Listen through headphone Plug a headphone with 3 5 mm plug into the 4 socket on the top panel Note e No audio output from the headphone socket when you play the playlist of a docked iPod iPhone iPad Listen through the speakers instead EN 35 11 Adjust sound The following operations are applicable to all supported media Adjust volume level e On the remote control press VOL repeatedly e On the main unit press VOL VOL repeatedly Mute sound Press K to mute or restore the sound Adjust default sound settings 1 Press SOUND repeatedly to select one of the setting menus e DSC Select a preset sound equalizer e DBB Select a DBB sound effect or disable it e FULL SOUND Enable to enjoy full range sound output 2 Press I4 BPI to select an option 36 EN O D 12 Adjust system settings Ge A Dy Press SETTINGS to access the menu of system settings Py L gt WIFI is displayed Lp we 2 Press amp W to select a menu option I e WIFI IP ADDR DIMMER NET RST FAC RST or VERSION 3 Press PPI to view system status or change system settings 6 e To return to the upper level menu press I lt ey Menu Function Remarks Option WIFI Display the status of connection Select WIFI and then
33. peatedly to switch the source to FM tuner L FM and the current frequency are displayed 2 Press and hold ed PPI until SEARCH SEARCH is displayed L The FM tuner tunes to a station with strong reception e To tune to a station at a specific frequency press M gt gt repeatedly until the desired frequency is displayed Program radio stations automatically Note e You can program a maximum of 20 preset radio stations Press and hold PROG CLOCK until AUTO SRH automatic search is displayed L gt All available stations are programmed in the order of waveband reception strength L The first programed radio station is broadcast automatically 30 EN O Program radio ations manually amp O You can program a maximum of 20 preset radiop stations e To overwrite a programmed radio station store A another one with its sequence number 1 Tune to a radio station On 2 Press PROG CLOCK to activate programming L gt PXX XX indicates the sequence number blinks 3 Press A V to allocate a sequence number from 01 to 20 to this radio station and then press PROG CLOCK to confirm L gt The preset sequence number and the frequency of this radio station are displayed 4 Repeat steps 1 3 to program more stations Tune to a preset radio station e Press A W to select the sequence number of that preset radio station e Enter its sequence number with numeric
34. rk automatically and then A you can enjoy music streamed by AirPlay Q Method 1 Use iOS 5 Wi Fi network login sharing 1 Connect your iPod touch iPhone iPad to y your home Wi Fi network 2 Dock your iPod touch iPhone iPad to the system see Enjoy audio through the dock on page 28 3 Press WIFI SETUP on the top panel L gt The following dialog box is displayed EN 17 share Wi Fi Settings Do you want to share your WI FI settings so this accessory can connect to the WI FI network Allow Ignore 4 Tap ALLOW allow to share your Wi Fi settings with this system 5 Wait less than 1 minute until the light stops flashing and you hear a confirmation tone Note e lf the confirmation tone does not beep in 2 minutes check the IP address of this system see Adjust system settings on page 37 If the IP address is displayed as 0 0 0 0 or 192 168 1 1 reconnect the power adaptor and then a confirmation tone beeps after boot up 18 EN Method 2 Coriect to a WPS router Gs Q 1 Press the WPS button on your Bome Wi Fi router 4 2 Shortly after step 1 press WIFI SETUP on the top panel WIFI SETUP Ss a L The LED indicator in the middle of WIFI SETUP button blinks yellow and green alternately L gt Within 2 minutes the LED indicator stops blinking and stays solid green and the speaker beeps L gt The system is connected to your home Wi Fi network success
35. st 2nd 3rd and 4th Z generations O iPod nano 2nd 3rd 4th 5th and 6th A generations Compatible iTunes host devices for AirPlay e AW Fi enabled PC Mac with iTunes 10 or later installed on and e the following iPod iPhone iPad models with IOS 4 3 or later e iPad 2 and iPad e Phone 4S iPhone 4 iPhone 3GS and iPhone 3G Pod touch 1st 2nd 3rd and 4th generations What s in the box Check and identify the contents of your package e Main unit e Remote control and two AAA batteries e FM antenna e WI FI antenna e AC power adaptor e Plug converter for AC power adaptor X 2 CD ROM for user manual e Quick start guide What else you need To stream audio wirelessly by AirPlay you need e aW l Fi certified router and e a host for your i Tunes music library for example an iPod touch iPhone iPad with IOS 4 3 or later or a Wi Fi enabled PC Mac with iTunes 10 or later installed on EN Overview of the main unit Qe 4D i l A nN N EN 10 QO GSO e Turn on the system e Switch the system to eco power standby mode or normal standby mode SOURCE e Press repeatedly to select a source gt il e Start pause or resume play E e Stop the play of music e Access the playlist of a docked iPod IPhone Disc compartment A e Press to eject the disc from the disc compartment lt lt gt i
36. the middle of WIFI SETUP button stays solid yellow L Anew Wi Fi network is created automatically with the network name SSID of Philips DCW8010 XXXXXX L It takes up to 45 seconds for successful creation of this new Wi Fi network a Note e After you finish the manual Wi Fi setting for this system this new Wi Fi network disappears e If you fail to enter Assisted Wi Fi Setup mode reconnect the power adaptor and then try again after successful boot up Make sure that no other Philips AirPlay enabled devices are in Assisted Wi Fi Setup mode at the same time Multiple new Wi Fi networks created this way may interfere with each other To change Wi Fi setup after first time setup press and hold WIFI SETUP for more than 3 seconds to reset Wi Fi settings Then follow the previous steps to change your network settings Connect your Wi Fi enabled device to the newly created Wi Fi network The new Wi Fi network created by this system only allows access of one Wi Fi enabled device To avoid interference from any other Wi Fi device you are recommended to temporarily disable the WI Fi function on your other Wi FI devices Option 1 Use your iPod touch iPhone iPad 20 EN h ae 1 Select Settings VI Fi on your iPod touch iPhone iPad _ Settings al Airplane Mode x nl Wi Fi AQ a gt l X 7 b ta Notifications w gt Ge 4 3 Carrier gt 2 Select Phi
37. urn on on Download the update file page 16 L It takes up to35 seconds for the system to boot up During boot up the LED indicator in the middle of the WIFI SETUP button blinks yellow L After boot up you can hear a beep GB United Kingdom english and the LED indicator stays solid XXXX ws yellow This system is connected to the last configured Wi Fi network automatically www philips com support brae wet Peer 2 Make sure that this system and your PC Mac are connected to the same Wi Fi router 3 Open Apple Safari on your PC Mac and then select Philips DCW8010 XXXXXX or the customized device name from the Bonjour pull down list 1 On your PC Mac go to www philips com e Or open another internet browser on support your PC Mac and then type in the IP 2 Enter the model number to find the latest address of this system available on the firmware upgrade file available Wi Fi router configuration page at the address bar L The configuration web page of this system Is displayed 3 Save the upgrade file to your hard drive 4 Follow the on screen instruction to complete the firmware update 38 EN N 2 ote e In case the firmware update fails you can try the above or procedures again O e After successful firmware update if there is any Sy problem with the Wi Fi connection reconnect the Lp power of this system and then set up the Wi Fi Lp network for this system again see Connect t
38. user customized nag from the AirPlay list amp Philips DCW8010 XXXXKXX Cancel EN 25 4 KN Q Stream from your RE Mac Select a media file and start play L After a while you will hear music from Q this system 1 Launch iTunes 10 or a fater version on your PC Mac Sten RTE 2 Click the AirPlay icon on the widow E p et e e a a l 3 Select Philips DCW8010 XXXXXX or user customized name from the AirPlay list 44 Ii Pi aa v LJ My Computer 26 Multiple Speakers ive a Note If you fail to hear music after successful setup do one of the following on your iPod touch iPhone iPad 1 Disconnect and then re connect to the same Wi Fi 4 Select a media file and start play Ours AGANE L gt After a while you will hear music from 2 Close all applications running at the background 3 Power off and then power on your iPod touch iPhone iPad again this system ss e et he eee ae EN e When you stream audio from your iTunes music library on a PC Mac you can select more than one AirPlay enabled devices if available at step 3 to stream music to all of them at the same time e lf you are using an earlier version of iTunes the AirPlay icon may be instead of Lal Control play You can select different play options from either your ITunes host device or this system Note e Make sure that you have successfull
39. wireless network Philips Fidelio device name Philips DCW8010 XXX Please select your wireless network and enter your network password if applicable For advanced network setup please click Advanced Click Apply to connect your wireless speaker to your network Please select your Wi Fi network Select Option ff lt Ls E If you use Safari on your Wi Fi enabled PC Mac you can also select Philips DCVWV8010 XXXXXX from the Bonjour pull down list to enter the configuration web page directly 1 Click gt Preferences L gt The Bookmarks menu Is displayed 22 EN n ato Vey Ario Pade 0322 cod ona pah ogag inceter Yee Isus Ady ab cy Nepas Fle Ek Ver koy Rona Wom Ht La hte thier kbb cumnb lec irda Ce E mps ype o openga raius 0 v pe ramiw rope Philips Fidelio r Welcors to Phil v Mecwork Configuration spea lt ar to your D 7 g Customize Toolbar Pnp kistaa Hide Menu Bar s Phape Pa Hide Bookmarks Bar Ctrl Shift B Hide Tab Bar Ctrl Shift T Hide Status Bar ctrl History Ctrl H Downloads Ctrl Alt L Private Browsing Reset Safari Block Pop Up Windows Ctrl Shift K Help F1 on Report Bugs to Apple Q Safari Extensions Gallery i 6 About Safari Da Katoto pri Fee D codon mitvak_entgar inceter ne 2 Tick Include Bonjour for Bookmarks bar Genma Appearance EEEN 3 Select Philips DCW8010 XXXXXX
40. y streamed audio from your iTunes music library to this system e To start or pause play press Il e To skip to the previous or next track press lt lt PPI e To adjust volume press VOL repeatedly e To mute or restore volume press X e To switch back to the AirPlay audio source press AirPlay e If you are streaming music from a PC Mac to control music play from this system launch iTunes and tick Allow iTunes audio control from remote speakers in Edit for Windows or iTunes for Mac gt Preferences gt Devices KN amp Use advanced und settings or If your iTunes host device is antipod touch iPhone iPad L For advanced sound settings and addi nal features you can use your IPod touch hovel iPad to download the Philips SoundStudio Uy application from Apple App Store It is a free gt O application from Philips K If your iTunes host device is a Wi Fi enabled O PC Mac For advanced sound settings you can use the equalizer available on iTunes directly View gt Show Equalizer Tip e See the iTunes help documentation for more details EN 27 7 Use the dock You can enjoy audio from iPod iPhone through this system Note e No audio output from the headphone socket in this situation Compatible iPod iPhone iPad models This system supports the following iPod iPhone and iPad models e iPad 2 and iPad e iPhone 4S iPhone 4 iPh
Download Pdf Manuals
Related Search