TG 0701 en
Contents
1. Connection diagram Test object After termination of the measurements is to be pulled the power supply plug out of the 230 V AC plug socket If the mains voltage resting against the device tester deviates from 230 V AC the read of measured values are to be corrected 230 V x read value mains voltage a For the measuring range mQ and mA measured value measured value ie a x read value b For the measuring range MQ 230 The checks are to be executed in the indicated order if an error is determined are to be executed after elimination of errors all programs under test again Technical data Power supply 230 V 207 253 V 50 Hz Power consumption 16 mA Fuse F 0 125 C DIN 41571 Work temperatur 10 30 C Function temperatur 10 50 C Measuring accuracy class 2 5 Dimensions W x H x D 98 x 144 x 56 mm Weight 700 g Available accessories Imitation leather bag Cleaning of the device is to be made with dry cloth in status without voltage Note Do not use the tester when you have reason to assume that it is not functioning perfectly or has been damaged The convenience outlet should be as close as ones possible at the tester arranged and easily accessible Make shure that the test piece under test is completely without tension attached Link test piece under test is admissible only also firmly installed certified mains cable In switching position insulation measuring key MQ pressed2. can be appropriate for 500 V DC between the contact secured test managment and the incorrect test piece under test if the alligator clip is loosened The security of the equipment tester is ensured only if it is used according to the operating instruction Subject to change 11 2012 Gilgen M ller amp Weigert Nuremberg GMW Zweigniederlassung der General Elektronik GmbH A Am Farrnbach 4A D 90556 Cadolzburg SN GMW vau Phone 49 0 9103 7129 0 Fax 49 0 9103 7129 205 207 e mail info g mw de Internet www g mw de M neuberger Me technik Electrical Appliance Tester TG 0701 USER S MANUAL Protective measure test according to standard DIN VDE 0701 0702 2008 06 for repaired or modified electrical equipment for domestic application and similar This device is built and checked according DIN EN 61010 part 1 VDE 0411 part 1 safety regulations for electrical mesuring control and laboratory instruments and the factory in safety relevant perfect status left In order to guarantee this status too received and a save operation the user must consider the notes and warning notes which are contained in this operating instruction Pay attention please with use to sufficient ventilation possibilities and avoid you the proximity of strong electromagnetic interference sources The devices of the series of TG 0701 correspond to the safety class system Il Note With the line up the sequence of the indicated poi
3. nts for safety reasons is to be observed absolutely Start up Check mechanical zero point of indicator and if necessary adjust with correction screw The alligator clip of the test line must be attached to a metallic part of the test piece key mQ pressed The test piece must be switched on and the mains plug must be plugged into the socket of the tester Power supply plug of the equipment tester is to plug into 230 V AC socket Indicator light must be illuminated Measurment of protective conductor resistance key mQ pressed Read resistance value on scale mQ Limit value lt 300 mQ Measuring range 0 1000 mQ Measuring current 0 2 A DC Insulation resistance test key MQ pressed Read resistance value on scale MQ Limit value Protection class gt 1MQ Protection class Il gt 2 MQ Measuring range 0 2 10 MQ Test voltage 500 V DC Rated short circuit current 1 mA 4 9 mA Leakage current equivalent measurment key mA pressed Read leakage current value on scale mA Limit value lt 3 5 kW lt 3 5 mA Equipment with heating element gt 3 5 kW lt 1mA kW Measuring range 0 18 mA Test voltage lt 40 V AC After the measurements pull of the power plug from the socket 230 V AC
Download Pdf Manuals
Related Search