Quick Setup Guide - Tri
Contents
1. IEC60950 1 standard Please refer to technical specifications for detailed information Installation amp Quick Setup Guide e Do not connect several devices to one power adapter as adapter overload may cause over heating or a fire hazard e Please make sure that the plug is firmly connected to the power socket When the product is mounted on wall or ceiling the device shall be firmly fixed e f smoke odor or noise rise from the device turn off the power at once and unplug the power cable and then please contact a qualified service technician A Cautions e Make sure the power supply voltage is correct before using the camera e Do not drop the camera or subject it to physical shock e Do not touch sensor modules with fingers If cleaning is necessary use clean cloth with a bit of ethanol and wipe it gently If the camera will not be used for an extended period please replace the lens cap to protect the sensor from dirt e Do not aim the camera at the sun or extra bright places Blooming or smearing may occur otherwise which is not a malfunction and affect the endurance of sensor at the same time e The sensor may be burned out by a laser beam so when any laser equipment is in use make sure that the surface of sensor will not be exposed to the laser beam Installation amp Quick Setup Guide Do not install the camera in areas outside of the normal operating range of 30 C 60 C and do not expose it to high el2. position the side outlet directly downward for water proof Downward Figure 2 7 Side Outlet Direction 2 2 2 Ceiling Mounting with Gang Box Steps 1 Disassemble the camera Refer to the section 2 1 2 Install the gang box in the ceiling 3 Attach the mounting base to the gang box with two screws 16 Installation amp Quick Setup Guide Figure 2 8 In ceiling Mount 4 Route the cables through the hole in the center of the mounting base 5 Align the camera with the mounting base 6 Tighten the screws to secure the camera with the mounting base 7 Connect the video output connector to the monitor Connect the power connector to the power supply 8 Adjust the image and focus Please refer to the section 2 3 for more detailed information 17 Installation amp Quick Setup Guide Figure 2 9 Secure Camera 9 Install the inner black liner back to the camera 10 Align the bubble with the camera 11 Tighten the screws to secure the bubble with the camera as shown in Figure 2 10 18 Installation amp Quick Setup Guide Figure 2 10 Secure the Bubble 2 2 3 Wall Mounting For the wall mounting you have to purchase a wall mount Steps 1 Disassemble the camera Refer to the section 2 1 2 Install the wall mount and mounting adapter as shown in Figure 2 11 3 Align the screw holes of the mounting base with the corresponding screw holes of the mounting adapter 4 Secure the mo
3. Northern IP3VFD 3 0 Megapixel IP Outdoor Varifocal IR Dome Camera Northery Installation amp Quick Setup Guide Northern 3625 Cincinnati Avenue Rocklin CA95765 855 388 7422 www northernvideo com Rev 020315 Installation amp Quick Setup Guide Thank you for purchasing our product If there are any questions or requests please do not hesitate to contact us About This Document This manual may contain several technical incorrect places or printing errors and the content is subject to change without notice The updates will be added to the new version of this manual We will readily improve or update the products or procedures described in the manual DISCLAIMER STATEMENT Underwriters Laboratories Inc UL has not tested the performance or reliability of the security or signaling aspects of this product UL has only tested for fire shock or casualty hazards as outlined in UL s Standard s for Safety UL60950 1 UL Certification does not cover the performance or reliability of the security or signaling aspects of this product UL MAKES NO REPRESENTATIONS WARRANTIES OR CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS OF THIS PRODUCT Installation amp Quick Setup Guide Regulatory Information FCC Information FCC compliance This equipment has been tested and found to comply with the limits for a digital device pursuant to part 15
4. ectromagnetic radiation To avoid heat accumulation good ventilation is required for operating environment Do not expose internal camera components to liquid or moisture When transporting the camera it should remain in its original packaging to avoid damage Improper use or replacement of the battery may result in hazard of explosion Replace with the same or equivalent type only Dispose of used batteries according to the instructions provided by the battery manufacturer If the product does not work properly please contact your dealer or the nearest service center Never attempt to disassemble the camera yourself We shall not assume any responsibility for problems caused by unauthorized repair or maintenance Installation amp Quick Setup Guide Table of Contents 1 Appearance Descriptio N o 8 2 installati O Msssnnnninnnsnnnon nnnnnn ie nnnnnninnnn ananin ans 10 2 1 Dis ssembling caxcesticonmerng tee mreiieeeaeeatinarenons 11 22 Mo nt Ng soseri onr2hssshecuseds E E 12 2 2 1 Ceiling MOUNTING veisssssscassasesoessevnernvsasisanroveassaseaneas 12 2 2 2 Ceiling Mounting with Gang BOX 16 2 2 3 Wall Mounting s sseeeeeeessssssssssssssrresrerererereressssese 19 2 3 Image and Focus Adjusting ceeeccccccceececeeeeeasaneeneeeees 22 3 Setting the Network Camera over the LAN s sssssssssrsssssssseeeosssssseresssss 25 4 Accessing via Web BrOWS f sssssssesesessssseeresssssssereessseeeeossssssereeosssssee
5. eeessss 30 Installation amp Quick Setup Guide 1 Appearance Description The overview of the network dome camera is shown below Figure 1 1 Overview Installation amp Quick Setup Guide Table 1 1 Description ee S E ree ere E Press RESET about 10s when the camera is powering on or rebooting to restore the default settings including the user name password IP address and port No etc Installation amp Quick Setup Guide 2 Installation Before you start e Make sure the device in the package is in good condition and all the assembly parts are included Make sure all the related equipment is powered off during the installation Check the specification of the products for the installation environment e Make sure the power supply matches with your required voltage to avoid damage e ifthe product does not function properly please contact your dealer or the nearest service center Do not disassemble the camera for repair or maintenance by yourself e Make sure that the wall is strong enough to withstand three times the weight of the camera E Nore For cameras with IR you are required to pay attention to the following precautions to prevent IR reflection e Dust or grease on the dome cover will cause IR reflection Please do not remove the dome cover film until the installation is finished If there is dust or grease on the dome cover clean the dome cover with clean soft c
6. ethods Steps 1 Run the SADP software to search the online devices 2 Check the device status from the device list and select the inactive device 27 Network Dome Camera Quick Start Guide Total number of ontine devices 3 D Seve as Caco Rebesn Meaty Networt Parameter aama Ownce Type Peaaawess Seariy Satwa asion IPat Gateway HTTP Pon Pacen KXON 192 168164 Active O Vexxebulld cco 192 16811 Ma Put XX XOOQOUOX 192 168164 inactive Verbul oeoo 192 16811 80 Sanat Mask XXOOOOUKKX 192 168164 Active Vexxbulld nooox 192 16811 80 PVE Gatewar Pe Adtress Pre Galway PAE Prefe Leng 0 HTTP Pot Deace Sen No Enatte DHCP Deace Aceaton New Pastors Song Contr Passwort eccccsee Figure 10 4 SADP Interface Note The SADP software supports activating the camera in batch Please refer to the User Manual of SADP software for details 3 Create a password and input the password in the password field and confirm the password 28 Network Dome Camera Quick Start Guide STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing using a minimum of 8 characters including upper case letters lower case letters numbers and special characters in order to increase the security of your product And we recommend you reset your password regularly especially in the high security system resetting the password monthly or weekly can better protect your product 4 Click OK
7. iling Refer to Conduit Installation on the Side for side cable routing 5 Attach the camera to the ceiling by aligning the holes of the back box with the holes on the ceiling 6 Secure the camera with the supplied screws as shown in Figure 2 3 TIT Figure 2 3 Secure the Camera 7 Route the cables through the cable hole 8 Connect the video output connector to the monitor Connect the power connector to the power supply 9 Adjust the image and focus Please refer to the section 2 3 for more detailed information 10 Install the inner black liner back to the camera 11 Install the bubble back to the camera and secure it with screws as shown in Figure 2 4 13 Installation amp Quick Setup Guide Figure 2 4 Secure Black Liner and Bubble Conduit Installation on the Side If you want to route the cables from side of the camera you need to follow the steps below to install a conduit for cable routing Steps 1 Rotate the water proof plug counterclockwise to remove it from the camera 14 Installation amp Quick Setup Guide Water proof Plug Side Cable Outlet Figure 2 5 Remove the water proof plug 2 Route the power cable and network cable through the side outlet to the conduit 3 Align and rotate clockwise the conduit to the side outlet tightly Conduit Figure 2 6 Install the Conduit to the Camera 15 Installation amp Quick Setup Guide E Note For wall mounting
8. loth and isopropyl alcohol 10 Installation amp Quick Setup Guide Make sure that there are no reflective surfaces too close to the camera lens The IR light from the camera may reflect back into the lens causing reflection e The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS Fasten the dome cover to camera body so that the foam ring and the dome cover are attached seamlessly 2 1 Disassembling Steps 1 Loosen the three screws on the edge of the bubble with the screw driver 2 Open the bubble and remove the inner black liner as shown in Figure 2 1 Black Liner a Pog Figure 2 1 Remove the Bubble and Black Liner 11 Installation amp Quick Setup Guide 2 2 Mounting Ceiling Mounting Steps 1 Disassemble the camera Refer to the section 2 1 2 Attach the drill template supplied to the place where you want to fix the camera 3 According to the drill template as shown in Figure 2 2 drill three screw holes in the ceiling Side Cable Outlet Cable Outlet Drilling Template for Outdoor Day Night Vandal proof Dome Camera Screw Hole Figure 2 2 The Drill Template 4 If you want to route the cables inside the ceiling drill a cable hole in the ceiling according to the drill template Skip this step if you 12 Installation amp Quick Setup Guide want to route the cables on the surface of the ce
9. mera Quick Start Guide 11 Accessing via Web Browser System Requirement Operating System Microsoft Windows XP SP1 and above version CPU 2 0 GHz or higher RAM 1G or higher Display 1024x768 resolution or higher Web Browser Internet Explorer 8 0 and above version Apple Safari 5 0 2 and above version Mozilla Firefox 5 0 and above version and Google Chrome 18 and above version Steps 1 Open the web browser 2 Inthe browser address bar input the IP address of the network camera and press the Enter key to enter the login interface Note The default IP address is 192 168 1 64 f the camera is not activated please activate the camera first according to Chapter 3 2 3 Input the user name and password The admin user should configure the device accounts and user operator permissions properly Delete the unnecessary accounts and user operator permissions Note The device IP address gets locked if the admin user performs 7 failed password attempts 5 attempts for the user operator 31 Network Dome Camera Quick Start Guide 4 Click Login English v UserName admin Password eeeee Login Figure 11 1 Login Interface 5 Install the plug in before viewing the live video and managing the camera Please follow the installation prompts to install the plug in rime A Nore You may have to close the web browser to finish the installation of the plug in 32 Network Dome Camera Q
10. o the User Manual of Network Camera for Activation via Client Software 10 2 1 Activation via Web Browser Steps 1 Power on the camera and connect the camera to the network 2 Input the IP address into the address bar of the web browser and click Enter to enter the activation interface Notes e The default IP address of the camera is 192 168 1 64 Activation Figure 10 3 Activation Interface Web 26 Network Dome Camera Quick Start Guide 3 Create a password and input the password into the password field STRONG PASSWORD RECOMMENDED We highly recommend you create a strong password of your own choosing using a minimum of 8 characters including upper case letters lower case letters numbers and special characters in order to increase the security of your product And we recommend you reset your password regularly especially in the high security system resetting the password monthly or weekly can better protect your product 4 Confirm the password 5 Click OK to save the password and enter the live view interface 10 2 2 Activation via SADP Software SADP software is used for detecting the online device activating the camera and resetting the password Get the SADP software from the supplied disk or the official website and install the SADP according to the prompts Follow the steps to activate the camera please refer to the User Manual of Network Camera for other two activation m
11. of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense FCC Conditions This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference 2 This device must accept any interference received including interference that may cause undesired operation EU Conformity Statement This product and if applicable the supplied 3 accessories too are marked with CE and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006 95 EC the EMC Directive 2004 108 EC the RoHS Directive 2011 65 EU Installation amp Quick Setup Guide 2012 19 EU WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier or dispose of it at designated collection points For more information upon the purcha
12. se of equivalent new equipment see www recyclethis info 2006 66 EC battery directive This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union See the product documentation for specific battery information The battery is marked with this symbol which may include lettering to indicate cadmium Cd lead Pb or mercury Hg For proper recycling return the battery to your supplier or to a designated collection point For more information see www recyclethis info Installation amp Quick Setup Guide Safety Instruction These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss The precaution measure is divided into Warnings and Cautions Warnings Serious injury or death may occur if any of the warnings are neglected Cautions Injury or equipment damage may occur if any of the cautions are neglected Warnings Follow these Cautions Follow these safeguards to prevent precautions to prevent serious injury or death potential injury or material A Warnings e Inthe use of the product you must be in strict compliance with damage the electrical safety regulations of the nation and region Please refer to technical specifications for detailed information e Input voltage should meet both the SELV Safety Extra Low Voltage and the Limited Power Source with 24 VAC or 12 VDC according to the
13. to save the password You can check whether the activation is completed on the popup window If activation failed please make sure that the password meets the requirement and try again 10 3 Modifying the IP Address Purpose To view and configure the camera via LAN Local Area Network you need to connect the network camera in the same subnet with your PC Then install the SADP software or client software to search and change the IP of network camera We will take modifying the IP Address via SADP software as an example to introduce the IP address modification Steps 1 Run the SADP software 2 Select an activate device 29 Network Dome Camera Quick Start Guide Note Please refer to Chapter 3 2 to activate the camera if the camera is inactive 3 Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP Modify Network Parameters IP Address Port Subnet Mask IPv4 Gateway IPv6 Address IPv6 Gateway IPv6 Prefix Length HTTP Port Device Serial No Enable DHCP Password 192 168 1 64 8000 255 255 255 0 192 168 1 1 0 80 XX XXXXXXX XXXXXXXX Save Figure 10 5 Modify the IP Address 4 Input the password to activate your IP address modification The batch IP address modification is supported by the SADP Please refer to the User Manual of SADP for details 30 Network Dome Ca
14. uick Start Guide Live View Playback Log Configuration Please click here to download and install the plug in Close the browser when installing the plug in Figure 11 2 Download Plug in Setup Web Components Click Next to continue or Cancel to eat Setup Figure 11 3 Install Plug in 1 33 Network Dome Camera Quick Start Guide E Setup Web Components Setup has finished installing Web Components on your computer Click Finish to exit Setup Figure 11 4 Install Plug in 2 6 Reopen the web browser after the installation of the plug in and repeat steps 2 4 to login Note For detailed instructions of further configuration please refer to the user manual of network camera 34
15. unting base to the mounting adapter with four screws 19 Installation amp Quick Setup Guide Mounting Base Figure 2 11 Install the Mounting Base Route the cables through the hole in the center of the wall mount Align the camera with the mounting base Tighten the set screws to secure the camera with the mounting base Connect the video output connector to the monitor Connect the power connector to the power supply Adjust the image and focus Please refer to the section 2 3 for more detailed information 20 Installation amp Quick Setup Guide Figure 2 12 Secure Camera 10 Install the inner black liner back to the camera 11 Align the bubble with the camera 12 Tighten the screws to secure the bubble with the camera 21 Installation amp Quick Setup Guide Figure 2 13 Secure Black Liner and Bubble 2 3 Image and Focus Adjusting Steps 1 3 axis adjustment 1 View the camera image using the monitor 2 Rotate the panning table to adjust the panning position of the camera 3 Rotate the tilting axes to adjust the tilting position of the camera 4 Rotate the lens table to adjust the azimuth angle of the image 22 Installation amp Quick Setup Guide ne Ea f AN gt AY P qp p Rotation Figure 2 14 3 axis Adjustment 2 Zoom and focus adjustment 1 View the camera image using the monitor 2 Loosen the zoom le
16. ver and move the lever between T Tele and W Wide to obtain the appropriate angle of view 3 Tighten the zoom lever 4 Loosen the focus lever and move the lever between F Far and N Near to obtain the optimum focus 5 Tighten the focus lever 23 Installation amp Quick Setup Guide Figure 2 15 Lens Adjustment 24 Network Dome Camera Quick Start Guide 10 Setting up Network Cameras over a LAN Note You shall acknowledge that the use of the product with Internet access might be under network security risks For avoidance of any network attacks and information leakage please strengthen your own protection If the product does not work properly please contact with your dealer or the nearest service center 10 1 Wiring Please connect to the camera to the network according to the following figures Network Camera Computer Figure 10 1 Connecting Directly PA gt 4 wy er A Ww awot Ork ble a o Network Camera Computer Figure 10 2 Connecting via a Switch or a Router 25 Network Dome Camera Quick Start Guide 10 2 Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera Activation via Web Browser Activation via SADP and Activation via Client Software are all supported We take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation Please refer t
Download Pdf Manuals
Related Search