1-3 Sconce Installation USER MANUAL
Contents
1. flatwire 1 3 Sconce Installation USER MANUAL Thank you for buying FlatWire We hope that you will enjoy installing and using our products FlatWire can be painted to greatly reduce the visibility of wire on your wall or completely hidden with mesh tape concealing compound mud amp paint Please read all instructions before initiating your installation Please visit www FlatWireReady com for additional products FAQs and technical assistance FlatWire Products for Installation x0 3 Check Ring Included with certain Sconces x1 3 Glass Dome x1 3 Retention Ring x1 3 Spring Clip x25 feet of Low Voltage FlatWire x2 5 CPC x2 5 CPC Back 27 x1 3 Wall Sconces S CPC CPC Back Connector x1 3 Glass Shades Adhesive gt x1 3 Mounting Brackets DVD anua x2 6 Finial Nuts x N Qum Qw x1 3 20 watt 1 2 6 2 6 2 6 B Halogen Bulbs xlFace Low Voltage x1 Mesh Drywall Phillips Slotted Type Q20T3 Transformer Tape Anchors Screws Screws Tools for Installation Pencil Screwdrivers Pliers Scissors Tape Measure Plastic Level Smoother Tools for Concealment SSS SSS y Roller or Paintbrush Painter s Paint Compound Compound Concealing Tape Knife Tray Compound INSTRUCTIONS PERTAINING TO A RISK OF FIRE OR INJURY IMPORTANT SAFETY INSTRUCTIONS Read all instructions Do not conceal or extend exposed conductors through a building wall Do not install this system2. CONTAINS HEXANE 110 54 3 ACETONE 67 64 1 XYLENE 1330 20 7 METHYL ETHYL KETONE 78 93 3 PROPANE 74 98 6 AND ISOBUTANE 75 28 5 Causes eye skin nose throat and respiratory tract irritation Vapor harmful May affect the brain or nervous system causing dizziness headache nausea or unconsciousness Prolonged exposure to skin may cause dermatitis May be harmful if absorbed through the skin Prolonged vapor inhalation may result in severe physical injuries Hexane exposure can cause peripheral nerve damage to arms and legs which may be permanent May be toxic to blood liver kidneys and reproductive system PRECAUTIONARY MEASURES FOR USE HANDLING STORAGE AND DISPOSAL Vapors may ignite explosively Vapors may cause a flash fire Prevent buildup of vapors by providing fresh air such that chemical odors can not be detected during use and while drying Open all windows and doors Keep away from heat sparks and open flames DO NOT smoke Vapors may travel long distances to a source of ignition and flash back Extinguish all flames and pilot lights and turn off stoves heaters electric motors burners and other sources of ignition and static electricity Disconnect all appliances during use and until all vapors are gone Vapors are heavier than air and will collect in low areas Check all low areas basements sumps etc for vapor before entering DO NOT breathe vapors Odor is not an adequate warning for hazardous conditions If you ex
3. pliers to protect surface finish of Finial Nut CAUTION DO NOT REMOVE SAFETY WARNING FROM FIXTURE Glass Shade will not fit into place in Fixture Base or is not Secure when mounted Glass Dome will not fit into lace on the Retention Ring check Ring Fixture components are not aligned properly Is Plastic Washer between Finial Nut and Fixture Base necessary Before Returning this Product PLEASE CALL 1 888 FLATWIRE Fixture is provided with Retention Ring already installed on Socket Engineering design sometimes causes Glass Shade to only fit in one orientation relative to Fixture Base Flash from the manufacturing process may cause thread interference with the Retention Ring and Socket Spring Clips are used to secure the Glass Dome onto the Retention Ring It is possible thattoo many Spring Clips were applied to the Retention Ring during manufacture Package contents can settle and vibrate during transportation causing minor alignment issues Plastic washer is to protect Fixture Base from being marred by Finial Nut Be sure to remove Retention Ring PRIOR to installing Glass Shade on Socket Rotate the Glass Shade until it drops into place If desired relocate safety warnings inside Glass Shade Remove Glass Shade and install ONLY the Retention Ring allowing the Retention Ring to move the FULL EXTENT ofthe Socket threads If you have purchased multiple sconces try swapping Re
4. EMERGENCIES such as SPILLS LEAKS FIRE EXPOSURE OR ACCIDENT 2 Typical FlatWire installation paths 1 for this technique warning on page 1 gt Ww E lt gt 5 o 79 oO s pa Read Spray Adhesive warning page 1 Keep Protective Barrier in Place Caution Risk of Fire Max 20 watt amp 4 R E N ce Please visit www FlatWireReady com for Tips amp Tricks as well as FAQs about the product installation Contact FlatWire regarding the splicing of FlatWire 1 888 FLATWIRE Basic Operation Turn Power on at Transformer amp then at Sconces Xm xL Turn Power off at Sconces and or at Transformer OFF 2 m m OFF OFF Finial Nut cannot be removed from Base Sometimes the locking fluid forthe Base Studs wicks up the Stud threads thereby locking the Finial Nut in place and not allowing its removal with finger pressure alone Ifthe Finial Nut is hexagonal in shape lightly apply pressure in counter clockwise direction with the correct size wrench Socket or with pliers wrapped with dish cloth around teeth of pliers to protect surface finish of Finial Nut If the Finial Nut is spherical lightly apply pressure in counter clockwise direction with pliers wrapped with dish cloth around teeth of
5. in wet locations To reduce the risk of fire and burns do not install this lighting system where the exposed bare conductors can be shorted or contact any conductive materials To reduce the risk of fire and overheating make sure all connections are tight Do not install any luminaire closer than 6 inches 15 25 cm from any curtain or similar combustible materials Turn off electrical power before modifying the lighting system in any way Lighted lamp is HOT WARNING To reduce the risk of FIRE OR INJURY Turn off power and allow to cool before replacing lamp Lamp gets HOT quickly Contact only switch plug when turning on Do nottouch hot lens guard or enclosure Keep lamp away from materials that may burn Do nottouch the lamp at any time Use a soft cloth Oil from skin may damage lamp Do not operate the luminaire with a missing or damaged shield Do not install this sconce lighting system in a moist or wet location Only wall sconces approved for use with the FlatWire system may be installed Fixtures must be FlatWire Ready gt Load the circuit of the transformer to no more than 60 watts Hazards amp Warning For FlatWire Ready Spray Adhesive DANGER EXTREMELY FLAMMABLE LIQUID AND VAPOR VAPORS MAY CAUSE FLASH FIRES CONTENTS UNDER PRESSURE VAPORS HARMFUL CAUSES EYE IRRITATION HARMFUL OR FATAL IF SWALLOWED KEEP OUT OF REACH OF CHILDREN DO NOT TAKE INTERNALLY VV vy vv vvv VVVVVVY DANGER
6. perience eye watering headache or dizziness or if air monitoring demonstrates vapor levels that are above applicable limits wear an appropriate properly fitted respirator during use and after application Follow respirator manufacturer s directions for respirator use DO NOT get in eyes on skin or clothing Wear appropriate gloves to prevent skin contact neoprene or nitrile Wear goggles or protective glasses with side shields Wash thoroughly after handling DO NOT use or store in direct sunlight DO NOT expose to heat or store at temperatures above 120 F Store away from stoves and radiators Exposure to heat or prolonged exposure to direct sunlight may cause bursting of the can DO NOT puncture or incinerate burn can Close container after use See Material Safety Data Sheet for additional information For a Material Safety Data Sheet contact your supplier or visit www flatwireready com FIRST AID EYE CONTACT Flush immediately with large amounts of water for at least 15 minutes and get medical attention immediately SKIN CONTACT Wash thoroughly with soap and water INHALATION If you experience difficulty breathing leave the area to obtain fresh air If continued difficulty is experienced get medical attention immediately INGESTION DO NOT INDUCE VOMITING Call physician immediately CALL 1 800 327 3874 IF IRRITATION OR COMPLICATIONS ARISE FROM ANY OF THE ABOVE ROUTES OF EXPOSURE U S and Canada CALL 1 800 535 5053 FOR CHEMICAL
7. tention Rings among them See if there are more than one Spring Clips between the Glass Dome and Retention Ring Only one is required to secure the Glass Dome in place Once Fixture is mounted lightly twist portions of Fixture by hand until you are satisfied with the appearance of your installation Once Fixture is mounted the plastic washer can be discarded as it is not necessary to the function of the fixture 10 Transf Input 120 volt 60 Hz 5 amp Output 12 volt 60 watts 12 volt 20 watt bulb maximum each Sconce Fixtures 3 Fixtures maximum per Transformer UL listed as Low voltage Lighting Systems Power Units Luminaires and Fittings Under 254977 Glass Dome Glass Shade Retention Ring amp Spring Clip Halogen Bulb Female Tab Connector Brass Tab Connector 13
Download Pdf Manuals
Related Search