Manual
Contents
1. Ultrasonic Thickness Gauge UM6500 Allright reserved 2013 Thanks for choosing our moisture meters For your easy to master this instrument as soon as possible please read following instructions carefully and always keep this meter within easy reach 1 Application Used for measuring thickness and corrosion of pressure vessels chemical equipment boilers oil storage tanks etc It applicable to the industries of petroleum shipbuilding power station and machine manufacturing Materials measured 11 types of materials including steel cast iron aluminum red copper brass zinc quartz glass polyethylene PVC gray cast iron nodular cast iron High resolution measurement Capture the value of the minimum thickness Status indicator of the coupling and low battery Autopower off function to 3 DESCRIPTIONS 3 1 3 2 3 4 3 1 sensor socket 3 2 low battery 3 3 mm indicator 3 4 inch indicator 3 5 Coupling indicator 3 6 Material selection key conserve battery life Humanized shape design compact and portable Can be used in harsh environment 2 Specifications Display 4 digits LCD with backlight Operating principle ULTRASONIC Measuring range 1 0 200mm in 45 Steel 0 05 8inch Resolution 0 1mm Accuracy 0 5 H 0 1 mm Depends on materials and conditions Units Metric Imperial unit selectable Power supply 4x1 5 AAA size UM 4 battery 3 7 Power key 3 8 Cal2. ct key 3 6 again or wait till the code automatically change to 0 after several seconds or the meter will automatically return to measurement state if measuring 5 CALIBRATION 5 1 Drop alittle oil on the 5 8 Notes 8 1 When big difference occurred please check as below 8 1 1If the material code is correct 8 1 2Re calibration 8 1 3There are air hole Non smooth inside material 8 2 please don t pull the wire of sensor often to avoid the wire broken or with bad contact ion 8 3 Keep the sensor clean when finished testing 8 4 Only can calibration on standard calibrate block other test block will mm standard block 3 10 5 2 Press the Calibration key 3 8 the CAL be shown on the Display CAL is the abbreviation of calibration 5 3 Put the sensor 3 11 on the standard block The coupling symbol 3 5 is on if coupling well 5 0 mm or 0 197 inch and CAL will be shown on the Display in turn When steady press CAL key 3 8 to confirm and then the unit return to the state of measurement 5 4 The calibration result will be auto saved to the unit once confirmation It is unnecessary to calibrate resultin big error or wrong value in our calibration method 5 8 5 Don t repair by yourself Non authrised repair method not only cause of the error measurement but also lose the warranty right often unless you suspect the accuracy of measurement 6 MEASURING PROCEDURE 6 1 Press t
3. he power key 3 7 to turn on the unit 6 2 Press the mm inch key 3 9 to select the right measurement unit 6 3 Press the Sensor 3 11 onto the material surface based on the material code selected is right Be sure that coupling is well and the symbol 3 5 is on The reading on display is the measurement value 6 4 The reading is held till a new measurement value is coming The last value is held Reference materials table CODE Material cd01 Steel cd02 Cast Iron cd03 Aluminum cd04 Red copper cd05 Brass cd06 Zinc cd07 Quartz glass cd08 Polyethylene cd09 PVC cd010 Gray cast iron cd011 Nodular cast iron on the display till the power is off 6 5 2 modes to turn off the power Manual off at any time by pressing the power key or Auto power off after about 1 minutes from last key operation 7 BATTERY REPLACEMENT 7 1 When the battery symbol appears on the display it is time to replace the batteries 7 2 Slide the Battery Cover away from the instrument and remove the batteries 7 3 Install batteries paying careful attention to polarity
4. ibration key 3 9 mm inch key 3 10 Test block 3 11 Ultrasonic sensor 3 12 Plus key 3 13 Minus key 3 14 sensor plug 4 MATERIAL SELECTION 4 1 Press the power key 3 7 to turn on the unit 4 2 Press the Material Selection key 3 6 and the code cdxx will showed on display cd is the abbreviation for code and xx is one number among 01 11 The cdxx material relationship refer to follow Table next page Power supply 4x1 5 AAA size UM 4 battery Low battery indicator Operating conditions 0 45C 32F 104F lt 90 RH Dimensions Main Unit 140mmx60mmx34mm Net Weight 180g Standard Delivery Main Unjfeeresrsssiisnsise 1 8mm Probe eee 1 Coupling Ojla 1 User Manual eese 1 Carrying CaS creererctreeee 1 4 3 Press the key 3 12 or key 3 13 to select the material code to measure and then press the Material Selection key 3 6 to confirm the display will show 0 If you select a material code but do not confirm the selection key the code will automatically change to O after several seconds In such case the meter will still reserve the material code before exiting 4 4 It is unnecessary to select the material code once the material code is confirmed automatically stored to the memory of the meter unless the measured material is different from that before 4 6 To browse the material code selected it only press the Select key 3 6 To exit browsing repress the Sele
Download Pdf Manuals
Related Search
Manual manual manualslib manual car manuale digitale manually meaning manual timesheet manual transmission manual wheelchair manual arts high school manually update your device drivers windows manual definition manual for courts martial manual labor manual lawn mower manual muscle testing manually register devices with autopilot manual muscle testing grades manual transfer switch manualidades manual blood pressure cuff manual handling manual transmission cars for sale manual digital manual pdf manual autopilot enrollment