Home
Installer Guid
Contents
1. 302V PG2 Installation Guide
2. 5 x 1 x 0 26 in Weight including battery 12g 0 42 oz Color White or brown D 304535 MC 302V PG2 Installation Guide 3 WARRANTY Visonic Limited the Manufacturer warrants this product only the Product to the original purchaser only the Purchaser against defective workmanship and materials under normal use of the Product for a period of twelve 12 months from the date of shipment by the Manufacturer This Warranty is absolutely conditional upon the Product having been properly installed maintained and operated under conditions of normal use in accordance with the Manufacturers recommended installation and operation instructions Products which have become defective for any other reason according to the Manufacturers discretion such as improper installation failure to follow recommended installation and operational instructions neglect willful damage misuse or vandalism accidental damage alteration or tampering or repair by anyone other than the manufacturer are not covered by this Warranty The Manufacturer does not represent that this Product may not be compromised and or circumvented or that the Product will prevent any death and or personal injury and or damage to property resulting from burglary robbery fire or otherwise or that the Product will in all cases provide adequate warning or protection The Product properly installed and maintained only reduces the risk of such events without warning and it is not
3. perpendicular to the device surface 2 2 Enrollment Refer to the PowerMaster panel s Installer Guide and follow the procedure under the 02 ZONES DEVICES option of the Installer Menu The following is a general description of the steps through the panel menu 1 02 ZONES DEVICES 2 ADD NEW DEVICES gt MODIFY DEVICES 3 ENROLL NOW or gt ENTR ID XXX XXXX 4 Z06 Contact Sens gt ID No 104 XXXX 5 Z06 LOCATION gt Z06 ZONE TYPE gt Z06 SET CHIME gt Z06 DEV SETTINGS A Q 01 3 LOCAL DIAGNOSTICS TEST Before testing separate the base from the cover see Figure 2 LED response Reception A Put back the cover to return the tamper switch to its normal Green LED blinks undisturbed position Yellow LED blinks B Momentarily open the door or window and verify the red LED Red LED blinks blinks indicating detection No blinks No communication See seconds nes of METER blinks 3 umes see ete IMPORTANT Reliable reception must be assured Therefore The following table indicates received signal strength indication Noor signal strength is not acceptable If you receive a poor signal from the device re locate it and re test until a good or strong signal strength is received Note For detailed Diagnostics Test instructions refer to the control panel Installer Guide 4 MISCELLANEOUS COMMENTS Visonic Ltd wireless systems are very reliable and are tested to B A receiver responds only to one transmitted sig
4. TO MC 302V PG2 al Visonic Supervised Vanishing Magnetic Contact Device Installation Instructions 1 INTRODUCTION _ The MC 302V PG2 is a very thin PowerG magnetic contact device that is compatible with PowerMaster control panels The device includes a built in reed switch that opens upon removal of a magnet placed near it The MC 302V PG2 sends the alarm message to the control panel using PowerG 2 way communications protocol A periodic supervision or alarm message is transmitted automatically The control panel is thus informed at regular intervals of the unit s active participation in the system The LED lights green yellow red according to signal strength upon first insertion of the battery and for the test period of 15 min B LED does not light while a supervision message or event is being transmitted Operating power is obtained from an on board 3 V Lithium battery When the battery voltage is low a low battery message is sent to the receiver The MC 302 V is available for 433 MHz 868 A Transmission LED B Magnet MHz and 915 MHz 2 INSTALLATION CAUTION This equipment shall be installed by Service Personnel in non hazardous indoor locations only 2 1 Mounting Figure 1 External View A Enroll button B Double sided adhesive tape Figure 2 Mounting Note The required battery is CR2032 Lithium 3V manufactured by VARTA or another UL recognized manufacturer purchased from a Visonic a
5. XCEED THE PURCHASE PRICE OF THE PRODUCT which shall be fixed as liquidated damages and not as a penalty and shall be the complete and exclusive remedy against the Manufacturer When accepting the delivery of the Product the Purchaser agrees to the said conditions of sale and warranty and he recognizes having been informed of Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages so these limitations may not apply under certain circumstances The Manufacturer shall be under no liability whatsoever arising out of the corruption and or malfunctioning of any telecommunication or electronic equipment or any programs The Manufacturers obligations under this Warranty are limited solely to repair and or replace at the Manufacturer s discretion any Product or part thereof that may prove defective Any repair and or replacement shall not extend the original Warranty period The Manufacturer shall not be responsible for dismantling and or reinstallation costs To exercise this Warranty the Product must be returned to the Manufacturer freight pre paid and insured All freight and insurance costs are the responsibility of the Purchaser and are not included in this Warranty This warranty shall not be modified varied or extended and the Manufacturer does not authorize any person to act on its behalf in the modification variation or extension of this warranty This warranty shall apply to the Product only All product
6. a guarantee or insurance that such events will not occur THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES OBLIGATIONS OR LIABILITIES WHETHER WRITTEN ORAL EXPRESS OR IMPLIED INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER WARRANTIES WHATSOEVER AS AFORESAID THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL INDIRECT INCIDENTAL CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS DAMAGE OR EXPENSE INCLUDING LOSS OF USE PROFITS REVENUE OR GOODWILL DIRECTLY OR INDIRECTLY ARISING FROM PURCHASER S USE OR INABILITY TO USE THE PRODUCT OR FOR LOSS OR DESTRUCTION OF OTHER PROPERTY OR FROM ANY OTHER CAUSE EVEN IF MANUFACTURER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH PERSONAL AND OR BODILY INJURY AND OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT INDIRECT INCIDENTAL CONSEQUENTIAL OR OTHERWISE BASED ON A CLAIM THAT THE PRODUCT FAILED TO FUNCTION W E E E Product Recycling Declaration Di Directive 2002 96 EC Waste Electrical and Electronic Equipment However if the Manufacturer is held liable whether directly or indirectly for any loss or damage arising under this limited warranty THE MANUFACTURER S MAXIMUM LIABILITY IF ANY SHALL NOT IN ANY CASE E
7. ce must accept any interference that may be received or that may cause undesired operation Le present appareil est conforme aux CNR d lndustrie Canada applicables aux appareils radio exempts de licence L exploitation est autorisee aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radioelectrique subi meme si le brouillage est susceptible d en compromettre le fonctionnement Reed Switch Positions Wood Supports Opening Closing Direction gt 11 mm lt 9 mm gt 14mm lt 12 mm gt 22 mm lt 20 mm gt 30 mm lt 2 mm Tt Fig 3 Range Coverage Directions APPENDIX SPECIFICATIONS Frequency Band MHz 433 868 915 in accordance with the prevailing frequency of your region Modulation GFSK Antenna Built in loaded inverted F antenna Communication Protocol PowerG Supervision Signaling at 256 sec intervals Battery type Varta 3V Lithium CR2032 Battery Life Expectancy When used with V18 PowerMaster systems Up to 5 years with typical use When used with V17 PowerMaster systems Up to 3 years with typical use Low Battery Threshold 2 1V Operating Temperature 10 C to 55 C 14 F to 131 F Storage Temperature 40 C to 85 C 40 F to 185 F Relative Humidity RH Up to 95 non condensing Dimensions LxWxD 433 868 MHz model 62 x 25 4 x 7 6 mm 2 5 x 1 x 0 3 in 915 MHz model 62 x 25 4 x 6 4 mm 2
8. llation Guide FCC Compliance Statement The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in residential installations This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio and television reception However there is no guarantee that interference will not occur in a particular installation If this device does cause such interference which can be verified by turning the device off and on the user is encouraged to eliminate the interference by one or more of the following measures Re orient or re locate the receiving antenna Increase the distance between the device and the receiver Connect the device to an outlet on a circuit different from the one which supplies power to the receiver Consult the dealer or an experienced radio TV technician WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment This device complies with FCC Rules Part 15 and with Industry Canada licence exempt RSS standard s Operation is subject to two conditions 1 This device may not cause harmful interference and 2 this devi
9. nal at a time high standards However due to low transmitting power and C Wireless devices should be tested regularly to determine limited range required by FCC and other regulatory authorities whether there are sources of interference and to protect there are some limitations to be considered against faults A Receivers may be blocked by radio signals occurring on or near their operating frequencies regardless of the digital code used 5 COMPLIANCE WITH STANDARDS amp 3 The MC 302V PG2 is designed to comply with the following Europe EN 300220 EN 301489 EN 50130 4 EN 61000 6 3 EN 60950 1 EN 50131 1 EN 50131 2 6 and EN 50131 6 Type C Certified by Applica Test and Certification The MC 302V PG2 is compatible with the RTTE requirements Directive 1999 5 EC of the European Parliament and of the Council of 9 March 1999 USA CFR 47 part 15 FCC Canada RSS 210 The Power G peripheral devices have two way communication functionality providing additional benefits as described in the technical brochure This functionality has not been tested to comply with the respective technical requirements and should therefore be considered outside the scope of the product s certification Security Grade Designed according to EN 50131 1 EN 50131 2 6 and EN 50131 6 Type C this equipment can be applied in installed systems up to and including Security Grade 2 Environmental Class EN 50131 2 6 Class II 2 D 304535 MC 302V PG2 Insta
10. pproved supplier D 304535 MC 302V PG2 Installation Guide 1 Note To comply with FCC and IC RF exposure compliance requirements the device should be located at a distance of at least 20 cm from all persons during normal operation The antennas used for this product must not be co located or operated in conjunction with any other antenna or transmitter 1 Insert a quarter coin in the slot as shown in the drawing and flex to remove the cover or if a quarter coin is not available 2 Insert a 4 mm flat screwdriver into the slot of the plastic cover as shown in the drawing and flex the slot to open that side of the plastic cover Insert the screwdriver into the slot on the other side of the plastic cover and repeat the procedure and then remove the cover Insert the battery at an angle see drawing while observing battery polarity and then press down on the battery Caution Risk of explosion if battery is replaced by an incorrect type Dispose of used batteries according to the manufacturer s instructions Peel away the release liners from the two strips of double sided adhesive tape and attach to the device and magnet Align the device with the magnet according to the location marks and fasten the device and magnet to the mounting surface The transmitter should be mounted on the fixed surface and the magnet on the moving surface 7 For installers of 433 or 868 MHz model Ensure that the heads of the tightened screws are flat
11. s accessories or attachments of others used in conjunction with the Product including batteries shall be covered solely by their own warranty if any The Manufacturer shall not be liable for any damage or loss whatsoever whether directly indirectly incidentally consequentially or otherwise caused by the malfunction of the Product due to products accessories or attachments of others including batteries used in conjunction with the Products This Warranty is exclusive to the original Purchaser and is not assignable This Warranty is in addition to and does not affect your legal rights Any provision in this warranty which is contrary to the Law in the state or country were the Product is supplied shall not apply Warning The user must follow the Manufacturer s installation and operational instructions including testing the Product and its whole system at least once a week and to take all necessary precautions for his her safety and the protection of his her property 1 08 For information regarding the recycling of this product you must contact the company from which you orignially purchased it If you are discarding this product and not returning it for repair then you must ensure that it is returned as identified by your supplier This product is not to be thrown away with everyday waste al Visonic EMAIL info visonic com INTERNET www visonic com VISONIC LTD 2014 MC 302V ROW D 304535 REV 4 10 14 D 50455 4 D 304535 MC
Download Pdf Manuals
Related Search
Related Contents
Kensington K60721US Protocol (50 prep) - Norgen Biotek Corp. Rexel Document Folder - Top Quality Documento PDF - AMS Tesi di Dottorato Capitolo 2. Regolazione ed uso del monitor 接続ガイド ユーザーズガイド(取扱説明書) WebAdmin v2.0.0 User Manual - ECO Tecna TE-90 manual EN Copyright © All rights reserved.
Failed to retrieve file