WADE-8016 User`s Manual
Contents
1. Switch with J29 CFEX SATA J25 SATA Gen3 Connector Support to SATA Gen3 J26 SATA Gen3 Connector Support to SATA Gen3 J27 DDR3 Slot Channel A DDR3 1333 G1820 Support 1333 only J28 DDR3 Slot Channel B DDR3 1333 G1820 Support 1333 only J29 CFEX Connector Switch with J24 SATA Switch with U21 SPI JP1 Case Open Enable JP2 External COM Port4 COM4 Only Support RS 232 JP5 Auto Power Button Enable Swith ATX Mode and AT Mode JP6 CFEX SPI SPI Switch SW1 ATX Detect amp BIOS Recovery Switch Haswell PCH H81 Haswell CPU Socket Note BIOS Socket JP3 controll enable the J24 or CFEX JP6 controll boot from the SPI ROM or CFEX SPI ROM WADE 8016 User s Manual Switch with J29 CFEX SPI 2 7 System Installation Chapter 3 System Installation This chapter provides you with instructions to set up your system The additional information is enclosed to help you set up onboard PCI device and handle Watch Dog Timer WDT and operation of GPIO in software programming 3 1 Intel Haswell Processor LGA 1155 CPU Socket In the top right corner of the CPU Socket is Pin1 and the red two circles are alignment key under m KE LGA 1155 CPU In the top the Yellow Triang Please remember to locate the alignment keys on the CPU socket of the motherboard and the notches on the CPU WADE 8016 Users Manual 3 1 System Installation LGA 1155 CPU Installation Steps Before install the2. USB Port 0 9 Disable USB port Choices Disable Enable WADE 8016 Users Manual 4 13 BIOS Setup Information Power Control Configuration Enable Hibernation Enable Hibernation Enables or disables system ability to hibernate OS 5S4 Sleep state Choices Disable Enable ACPI Sleep States Select ACPI sleep state the system will enter when the suspend button is pressed Choices S3 only suspend to RAM Wake system with Fixed Time Enable or disable system wake on alarm event Choices Disable Enable Wake on Ring Enable or disable wake on ring from S5 Choices Disable Enable WADE 8016 Users Manual 4 14 BIOS Setup Information TPM Configuration Security device support Enable or disable BIOS support for security device Choices Disable Enable Super IO Configuration FE TUE WADE 8016 Users Manual 4 15 BIOS Setup Information WDT controller Enable WDT configuration Choices Disable Enable Serial Port 1 4 Choices Disable Enable H W Monitor Smart System Fan Function Enabled Smart system fan function Choices Disable Enable System fan mode Smart fan mode select Choices Thermal Cruise TM Mode Fan Speed Cruise TM Mode System Target Temp System fan target temperature range 0 127 System Tolerance Temp System fan Tolerance temperature range 0 15 WADE 8016 Users Manual 4 16 BIOS Setup Information Smart CPU fan function Choices Disable Ena
3. Dual Core H2 socket LGA1150 PCI Express x16 A illl 4 Dual channel DDR3 Channel A 1333 1600 on two DIMM gu y Shark Bay Processor Memory Up to 16GB system memoy mE A mE Channa B DVI Inta FDI ALC892 USB 3 0 2 ports USB 2 0 4 ports USB 2 0 4 ports SATA 6Gb 2 ports SATA 3Gb 2 ports W83627UHG Super IO H W Monitor COM 3 RS 232 mm COM A RS 232 On Board connector COM 1 RS 232 Oi Board connector COM 2 RS232 422 485 Rear IO connector WADE 8016 System Block Diagram WADE 8016 Users Manual 1 6 Hardware Configuration Chapter 2 Hardware Configuration This chapter gives the definitions and shows the positions of jumpers headers and connectors All of the configuration jumpers on WADE 8016 are in the proper position The default settings shipped from factory are marked with an asterisk 2 1 Jumper Setting ppe o 89 o o O10 J9 O O O O O a oooon fF oooon Cb 000000000000000000000000000000000000 00000 tiv o o o o i o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o o00000000000000000000000000000000000 00000000000000000000000000000000000 000000000000000000000000000000000000 000000000000000000000000 000000000000000000000000000000000000 000000000000000000000000 2000000000000 2000000000 000 000000 o or ar e e
4. select pin number pin 5 int mode 0 select I O mode output int value 1 set GPO value high int tmp 1 lt lt pin num ifpin num lt 0 pin num gt MAX GPIO NUM mode lt 0 mode gt 1 value 0 value gt 1 printf GPIO Pin Set Invalid parameter n return 1 j Enter the Extended Function Mode outp EFER 0x87 outp EFER 0x87 Now set the configuration register outp EFER DEVICE NUM REG Select Logic Device Number Register outp EFER 1 GPIO LOGIC NUM device number for GPIO2 3 4 5 is 9 outp EFER GPIO BASE REG outp EFER 1 0x07 outp EFER GPIO IO REG Select GPIO3 I O Register outp EFER L inp EFER 1 amp tmp tmp mode Set I O mode 0 output 1 input 1 mode is GPO set value if mode GPIO MODE OUT outp EFER GPIO DATA REG Select GPIO3 Data Register outp EFER 1 inp EFER 1 amp tmp tmp value Set GPO value 0 low 1 high printf GPIO Pin Set Set GPIO d to GPO Value d n pin num value j WADE 8016 Users Manual 3 9 System Installation else printf GPIO Pin Set Set GPIO d to GPI n pin num j Exit the Extended Function Mode outp EFER 0xAA return 0 WADE 8016 Users Manual 3 10 BIOS Setup Information Chapter 4 BIOS Setup Information WADE 8016 is equipped with the AMI BIOS stored in Flash ROM These BIOS has a built in Setup program that allows users to modify t
5. ASPM L1 ASPM LOsL1 Enable PEG Choices Disable Enable Auto WADE 8016 Users Manual 4 10 BIOS Setup Information SATA Configuration SATA Controller s Enabled SATA Controller s Choices Disable Enable SATA Mode Selection Determines how SATA controller s operate Choices IDE AHCI SATA Controller Speed Indicates the maximum speed the SATA controller can support Choices Default Gen1 Gen2 Gen3 Serial ATA Port 0 3 Capabili Port 0 1 2 3 Choices Enable Disable Hot Plug Designates this port as Hot Pluggable Choices Enable Disable WADE 8016 User s Manual 4 11 BIOS Setup Information Mechanical Presence Switch Controls reporting if this port has an Mechanical presence switch Choices Enable Disable External SATA Choices Enable Disable SATA Device Type Identify the SATA port is connected to Solid State Drive or Hard Disk Drive Choices Hard Disk Drive Solid State Drive USB Configuration USB Configuration settings Legacy USB Support Enabled Legacy USB Support Enable legacy USB support Choices Enable Disable Auto USB3 0 Support External Enable disable USB3 0 XHCI Controller support Choices Enable Disable WADE 8016 Users Manual 4 12 BIOS Setup Information XHCI Hand off Choices Enable Disable EHCI Hand off Choices Enable Disable USB Mass Storage Drive Support Choices Enable Disable PCH USB Configuration USB Port 0 Enabled
6. It can select two of them to use dual display function This combination makes WADE 8016 an excellent piece of multimedia hardware Drivers Support Please find the Graphic drivers in the WADE 8016 CD title The driver supports Windows 7 3 3 3 On board Gigabit Ethernet Controller Drivers Support Please find Realtek RTL8111G CG 10 100 1000M LAN driver in Ethernet directory of WADE 8016 CD title The driver supports Windows 7 3 3 4 Realtek ALC892 HD Audio Controller Please find Realtek ALC892 High Definition Audio driver form WADE 8016 CD title The driver supports Windows 7 WADE 8016 Users Manual 3 6 System Installation 3 4 Clear CMOS Operation The following table indicates how to enable disable Clear CMOS Function hardware circuit by putting jumper in the board PIN No Clear CMOS GO oo DOY JP1 J9 Oo o o oJ 10 0000 0000000000 jJoooo00000 a oooon oooon E Se sep je 000000000000000000000000000000000000 0000 0 1 o000000000000000000000000000000000000 00000 o00000000000000000000000000000000000 o00000000000000000000000000000000000 n 000000000000000000000000000000000000 BAN P Y PT Y Y TY YYY TY YT I TPIPITTTIPTITYPPTYYTYTYYTYY rrr rr AAA TA po Cute O08 900000000000000000000000000000000000 OOM OOOOODO OOOO OO OOOO OOOO NOOO DO Ot BAA A AAA 209 Qooooooooooooooo0OOoOoQ0O0O000 WADE 8016 Users Manual 3 7 System Installation 3 5 WDT F
7. requires to launch active boot option Choices Disable Enable Boot mode select Select boot mode legacy UEFI Choices Legacy UEFI Boot Option 1 7 Select the system boot order Choices Hard Disk CD DVD USB Hard Disk USB CD DVD USB Key USB WADE 8016 Users Manual 4 19 BIOS Setup Information 4 5 Security Administrator Password Set administrator password User password WADE 8016 Users Manual 4 20 BIOS Setup Information 4 6 Save amp Exit Save Changes and reset Reset the system after saving the changes Disable changes and reset Reset system setup without saving any changes Restore defaults Restore load default values for all the setup option WADE 8016 Users Manual 4 21 Troubleshooting Chapter 5 Troubleshooting This chapter provides a few useful tips to quickly get WADE 8016 running with success As basic hardware installation has been addressed in Chapter 2 this chapter will primarily focus on system integration issues in terms of BIOS setting and OS diagnostics 5 1 Hardware Quick Installation ATX Power Setting Unlike other Mini ITX board computer WADE 8016 supports ATX only Therefore there is no other setting that really needs to be set up However there are only two connectors that must be connected J17 24pins ATX Power Connector Fighre It is assumed that users have correctly adopted modules and connected all the devices cables required before turning on AT
8. 2 6350P 350W Operting Temperature 0 C 60 C Storage Temperature 20 80 C O Relative Humidity 0 90 non condensing Operting Temperature 0 C 60 C Storage Temperature 20 80 C O Relative Humidity 0 90 non condensing WADE 8016 User s Manual System Overview 1 3 1 Mechanical Drawing NADAN n Ss 2553 g g go A Est amp Keep o n 166 32 i esir cs omponen SEU 162 64 155 12 Lr dere Dette aso 15512 sa 48 66 136 09 e J 48 41 126 06 Vl Ce 48 28 LR ag 39 36 11572 KHH S El 128 20 i ROS iz ES e Jed component Helgh 20m r N GDA BR du Re ag Pir ao Bait N ls dun N d 742 ied componenti Height imm Hu d a Bot SE Kou AH i 61 92 HH diit HH e ed compo Hejghiz im 4 iE ted i 0 97 NNNM 33 86 24 65 pu NN 1 restricted component Heigntedmn o EE d i o e 5 SgRERAZSI gt N SSS SESIO esticted component Heloh 10mm estricted component Heighi L2mm Ke mpone eigh nm ed component He 2 6mm Oj ad Each sid Ho Po h sia man 136 98 112 18 AA yy 01 87 Ye AUG ES a 1 li 7 SSS NN Ge QF 6 87 NS SNE WG N ER e E Ss 3 9 amp Y ES y 3s Ee Se n Ge out zeen WADE 8016 Users Manual System Overview 1 4 System Architecture All of details operating relations are shown in WADE 8016 System Block Diagram Quad Core
9. C NE LLL ps NN Bo 95 7 5 TXD Transmit Data RX CIS Clear to Send N C 7 DTR Data Terminal RX N C Ready RI RingIndicator N C GND Ground GND N C WADE 8016 Users Manual 2 5 Hardware Configuration J5 Audio connector PIN No Signal Description Red Mic Connector Allocation I O peripheral devices are connected to the interface connectors Connector Function List Connector Function J2 DVI VGA Connector J3 COM Port 1 and COM Port 2 COM2 Support RS 232 422 485 J4 Key Board Mouse Connector PS 2 J RJ45 LAN 1 Connector USB 2 0 Connector RJ45 LAN 2 Connector USB 2 0 Connector J5 Audio Connector J6 HDMI Connector 7 SMBus Connector General Purpose Connector External COM Port 3 Connector Only Support RS 232 External USB 3 0 Connetor J TPM Connector 13 J14 4 Pin ATX Power Connector J15 CPU Fan Connector J16 Battery Cpnnector J17 24 Pin ATX Connector J18 PCIE X16 Connector Support to PCIE Gen2 H81 Support Gen2 only J19 Front Pannel Connector J20 External USB 2 0 Connetor J External USB 2 0 Connetor SATA Gen2 Connector 2l J22 System Fan Connector J23 Support to SATA Gen2 J24 SATA Gen2 Connector WADE 8016 Users Manual Support to SATA Gen2 2 6 Hardware Configuration
10. CPU please make sure to turn off the power first 1 Open the load lever 3 Remove the plastic cap on the CPU socket Before you install the CPU always cover it to protect the socket pin WADE 8016 User s Manual 3 2 System Installation 4 After confirming the CPU direction for correct mating put down the CPU in the socket housing frame Note that alignment keys are matched CM 5 Make sure the CPU has been seated well into the socket If not take out the CPU and reinstall WADE 8016 Users Manual 3 3 System Installation 6 Engage the load lever while pressing down lightly onto the load Plate WADE 8016 Users Manual 3 4 System Installation 7 Push the CPU socket lever back into its locked position SAM 8 Please make sure four hooks are in proper position before you install the core 3 2 Main Memory WADE 8016 has two 240 pin DIMM sockets which supports Dual channel 1333 1600 DDR3 SDRAM as main memory Non ECC Error Checking and Correcting non register functions The maximum memory can be up to 16GB Memory clock and related settings can be detected by BIOS via SPD interface For system compatibility and stability do not use memory module without brand Memory configuration can be set to either one double sided DIMM in one DIMM socket or two single sided DIMM in both sockets Beware of the connection and lock integrity from memory module to socket Inserting Improperly it will aff
11. Description 1 USB2_P0_DP_R 2 3 1 USB3_TX2_DN_ 1 1 1 GIG Q2 EE m 3o o 4 GND ww USBB DODNR 5 USB TXL DN R _ 15 USB DODPR 6 pro Bo pel Ciclo HD Or amp 7 LUSBS TXLDP R 16 GND_ ND 17 Lu RO DNR JSB2 PO DP R ND p oup l N O WADE 8016 User s Manual 2 3 Hardware Configuration J13 TPM Connector Signal Description LFRAME NC PLTRST 5V J14 4 Pin ATX Power Connector s gt a AB nl J15 CPU Fan Connector PIN No Signal Description PIN No Signal Description a GND 2 ars Fan on off output Fan Speed control J16 Battery Connector PIN No Signal Description PIN No Signal Description J17 24 Pin ATX Power Connector 3 Loun KV SGN EE 7 GND 8 ATXPower0K 9 woVsb Ja nV WADE 8016 Users Manual 2 4 Hardware Configuration J19 Front Pannel Connector Signal Description 1 2 Speaker PWR_LED 4 NC J7LAN_ACT 6 NC J7LAN_LINK 19 J8LAN_LINK 10 GND J8LAN_ACT HDD_LED HDD LED 16 GND J20 J21 USB 2 0 Connector 5 Uss Je US 7 LOND 8 Tonn 9 NC 410 GND J22 System Fan Connector 3 jFanon offouput ________ 3 COM1 COM2 Serial Port Connector RS 232 422 485 PIN No Signal Description COM2 Detect 2 DSR Data Set Ready N C 3 RXD Receive Data TX DATA ie a 4 RIS Request to N C N
12. IRQ Peripheral devices can use interrupt request line s to notify CPU for the service required The following table shows the IRQ used by the devices on board IRO Current Use Default Use IRQ 0 System ROM System Timer IRQ 1 System ROM Keyboard Event IRQ 2 Unassigned Usable IRO IRQ 3 System ROM COM2 IRQ 4 NEWMOUSE COMI IRQ 5 Unassigned Usable IRQ IRQ 6 System ROM Diskette Event IRQ7 Unassigned Usable IRQ IRQ 8 System ROM Real Time Clock IRQ 9 Unassigned Usable IRQ IRQ 10 Unassigned Usable IRQ WADE 8016 User s Manual 5 3 Troubleshooting IRO 11 Video ROM IRO 12 NEWMOUSE IRO 13 System ROM IRO 14 System ROM IRO 15 Unassigned Usable IRQ IBM Mouse Event Coprocessor Error Hard Disk Event Usable IRQ WADE 8016 Users Manual 5 4
13. Intel AHT Enabled Intel AMT Enable or disable Intel Active Management Technology BIOS Extension Choices Disabled Enabled WADE 8016 Users Manual 4 5 BIOS Setup Information Un Configure ME OEMHlag Bit 15 Un Configure ME without password Choices Disabled Enabled Disable ME Set ME to Soft Temporary Disabled Choices Disabled Enabled Memory Information WADE 8016 Users Manual 4 6 BIOS Setup Information LAN Configuration Launch PXE OpROM policy Disabled Launch PXE OpROM policy Controls the execution of UEFI and Legacy PXE OpROM Choices Disable UEFI only Enable RTL8111G CG PCIE LAN Controller 1 2 Control the PCI Express Root Port Choices Disabled Enabled Wake on LAN Enable or disable the wake on LAN feature Choices Disabled Enabled WADE 8016 Users Manual 4 7 BIOS Setup Information Graphics Configuration Primary Display Primary Display Select which of IGFX PEG Graphics device should be Primary Display Choices Auto IGEX PEG Primary PEG Select PEGO PEG1 PEG2 PEG3 Graphics device should be Primary PEG Choices Auto PEG1 PEG2 Internal Graphics Keep IGD enabled based on the setup options Choices Auto Disable Enable Aperture Size Select the Aperture Size Choices 128MB 256MB 512MB DVMT Pre Allocated Select DVMT 5 0 Pre Allocated Fixed Graphics Memory sized used by the Internal Graphic Device WADE 8016 User s Manual 4 8 BIOS S
14. WADE 8016 Mini ITX Board User s Manual Version 1 1 Copyright Portwell Inc 2014 All rights reserved All other brand names are registered trademarks of their respective owners Preface Table of Contents How to Use This Manual Chapter 1 System Over Vie Wenn 1 1 Dot Introduction a i atr i e De duco totales eu tH reu Eo er arenas 1 1 L2 GC UB AAA DAP aT ERR EE POPE M P IN 1 2 1 3 Product Specification eic accen aa a i 1 2 1 3 1 Mechanical DEGWITB dei tet M rte eret taps tento a PL aereo Ens pfe 1 5 1 4 System Architecture ns nit 1 6 Chapter 2 Hardware Configuration ccsssccseeeeeeseeeesseeeeseeneneeeeseaeeeseeeseseeeeeeneseseaesaseeeenseeeeeas 2 1 Steet egene 2 1 Chapter 3 System Installation eese eeeeeeeees esee nennen nnn nn annnm nnne tnnt nn nnn 3 1 3 1 Intel Haswell Processor i one rro erteilen eret ceto ae eg 3 1 32 Main DMEMOY siii di ageleet 35 3 3 Installing the Mini ITX Board Computer 3 6 3 3 1 Chipset Component Driver eie ii E eae eek ec erts 3 6 3 3 2 Intel Integrated Graphics Controller eerte teret tio 3 6 3 3 3 On board Gigabit Ethernet Controller esses 3 6 3 3 4 Realtek ALC892 HD Audio Controller sese 3 6 34 Clear CMOS Operation Leber Ret pe coc acp dod eR edu 3 7 39 WDT BURCH OI E 3 8 Eeer Eege 3 9 Chapter 4 BIOS Setup Information 1sseeeeeeeeeeeeeeeeeees esee nennen nnn a nn
15. X power 240 pin DDR3 Memory keyboard mouse SATA hard disk VGA connector power cable of the device ATX accessories are good examples that deserve attention With no assurance of properly and correctly accommodating these modules and devices it is very possible to encounter system failures that result in malfunction of any device To make sure that you have a successful start with WADE 8016 it is recommended when going with the boot up sequence to hit Del key and enter the BIOS setup menu to tune up a stable BIOS configuration so that you can wake up your system far well WADE 8016 User s Manual 5 1 Troubleshooting Loading the default optimal setting When prompted with the main setup menu please scroll down to Load Setup Defaults press Enter and select Y to load in default optimal BIOS setup This will force your BIOS setting back to the initial factory configuration It is recommended to do this so you can be sure the system is running with the BIOS setting that Portwell has highly endorsed As a matter of fact users can load the default BIOS setting any time when system appears to be unstable in boot up sequence 5 2 FAQ System SBC keeps beeping and no screen has shown Solution In fact each beep sound represents different definition of error message Please refer to table as following Beep sounds Meaning Action One long beep with oneDRAM error Change DRAM or reinstall it short beeps One long b
16. aed e A AA AAA AAA AS 900000000000000000000000J28 o000000000000000000000000000000000000 o0000000000000000000000 ooo o00000000000000000000000000000000 oooooo0o000000000000000000 WADE 8016 Users Manual Hardware Configuration JP1 Case Open Pin Header PIN No Signal Description JP2 External COM Port 4 R5232 Only h 2 RM 3 TXD 4 J DIRM 5 LOND SRA 7 Jm CTS 9 RM4 10 JP3 CEEX SATA Select PIN No Signal Description CFEX Enable SATA J24 Disable SATA J24 Enable CFEX Disable JP4 Clear CMOS Select PIN No Signal Description 1 2short Normal Clear CMOS JP5 Auto Power Button Select PIN No Signal Description Enable AT Mode Disable ATX Mode JP6 CFEX SPI SPI Select PIN No Signal Description CFEX SPI Boot from J29 SPI ROM SPI Boot from U21 EEPROM J4 Key Board Mouse Connector PS 2 5 GD Je GND 7 5VDUAL Je VKBMS 9 MScK 10 KB CK WADE 8016 Users Manual 2 2 Hardware Configuration J9 SMBus Connector PIN No Signal Description PIN No Signal Description SMBus Clock n AE O pl E J10 General Purpose I O Connector 5 Gros J 6 LO _ 7 Lemos 8 GPO507 9 GND ts J11 External COM Port 3 RS 232 Only 5 Jeun L Liebe ps RTS 3 8 CTSH3 RI 3 J12 External USB 3 0 Connector Signal Description Signal
17. ble CPU fan Mode Smart fan mode select Choices Thermal CruiseTM Mode Fan Speed CruiseTM Mode CPU Target Temp System fan target temperature range 70 127 CPU Tolerance Temp System fan Tolerance temperature range 0 15 Case Open Warning Support case open warning beep Choices Disable Enable Serial Port Console Redirection Disabled Console redirection Choices Disable Enable WADE 8016 User s Manual BIOS Setup Information 4 4 Boot Bootup NumLock State Bootup NumLock State Select the keyboard numlock state Choices On off GateA20 Active UPON REQUEST GA20 can be disabled using BIOS servies Choices Upon Request Always Option ROM Messages Set display mode for option ROM Choices Force BIOS Keep Current INT19 Trap Response Bios reaction on INT19 trapping by option ROM IMMEDIATE execute the trap right away POSTPONED execute the trap during legacy boot Choices IMMEDIATE POSTPONED Launch Storage OpROM Control the of storage oprom enable disable Choices Disable Enable WADE 8016 Users Manual 4 18 BIOS Setup Information Full Screen Logo Enable or disable quiet boot option and full screen logo Choices Disable Enable Post Report Post report support enabled disabled Choices Disable Enable Summary screen Summary screen support enabled disabled Choices Disable Enable Fast Boot Enabled or disabled boot with initialization of a minimal set of devices
18. ch as cost effective of CPU performance or industrial systems WADE 8016 is based on the Intel Haswell processor and Intel H81 chipset The Intel H81 Express Chipset when combined with a processor from the Intel Dual Core Quad Core processor family delivers smart security cost saving manageability and intelligent performance for business platforms WADE 8016 is the first Portwell off the shelf product by Intel H81 Express Chipset it can be an embedded solution and a good platform for customer to integrate it to the embedded system WADE 8016 showcased one of Portwell upcoming motherboard for the Intel Haswell processors The WADE 8016 is based on the forthcoming Intel H81 chipset and supports the new LGA 1150 socket socket that will be used by Haswell processors This board has lots of features including supports total 2x SATA 3 SATA 6 0 Gbps storage specification and supports the latest PCIe 2 0 one PCI Express x16 slot devices for double speed and bandwidth which enhances system performance one CF slot on board supports Portwell exclusive CFEX SATA interface two long DIMM memory slot for DDR3 SDRAM up to 16GB support total 10 USB ports 4x rear IO by USB2 0 4x on board by USB2 0 4x on board by USB3 0 VGA HDMI DVI and two Gigabit Ethernet WADE 8016 Users Manual 1 1 System Overview 1 2 Check List The WADE 8016 package should cover the following basic items AN ie SS One WADE 8016 Mini ITX Main Board On
19. e View or set system date The date format is Day Month Date lt Year gt Use or to configure system Date System Time View or set system time The time format is Hour Minute Second Use or to configure system Time WADE 8016 Users Manual 4 2 BIOS Setup Information 4 3 Configutation Setup Warning Setting items on this screen to incorrect values may cause system to malfunction CPU Configuration WADE 8016 Users Manual 4 3 BIOS Setup Information Active Processor Cores Number of cores to enable in each processor package Choices All 1 2 3 Intel Virtualization Technology When enable a VWM can utilize the additional hardware capabilities provide by Vander pool Technology Choices Disable Enable EIST Disable Enable Intel Speed Step Choices Disable Enable Turbo Mode Turbo Mode Choices Disable Enable CPU C States Disable or Enable CPU C states Choices Disable Enable Chipset Configuration High Precision Timer Enabled WADE 8016 Users Manual 4 4 BIOS Setup Information High Precision Timer Enable or disable the High precision Event Timer Choices Disabled Enabled Azalia Control Detection of the Azalia device Choices Disabled Enabled VT d Check to enable VT d function on MCH Choices Disabled Enabled Port 80h Redirection LPC Bus Forward I O Port 80 to LPC Choices LPC Bus AMT Configuration
20. e SATA Cable One I O Shield bracket One Installation Resources CD Title If any of these items is damaged or missing please contact your vendor and keep all packing materials for future replacement and maintenance 1 3 Product Specification Main Processor Intel Dual Core Quad Core LGA1150 processor CPU clock bus 1333 1600 MHz Chipset Intel H81 chipset System BIOS AMI BIOS Main Memory Two 240 pin DDR3 Long DIMM socket support up to 16GB dual channel 1333 1600 MHz memory Expansion Interface One PCIex16 One CFEX SATA interface SATA Interface Two SATA 6Gb ports Iwo SATA 3Gb ports Serial Port Support total four com ports one RS232 and one RS232 422 485 on rear I O two RS232 on board header USB Interface Support Ten USB Universal Serial Bus ports four on rear I O USB2 0 and six on board header 4x USB 2 0 2x USB 3 0 for internal devices Audio Interface Connector for Mic In Line In and Line Out Real Time Clock Calendar RTC Support Y2K Real Time Clock Calendar WADE 8016 Users Manual 1 2 System Overview Watch Dog Timer Support WDT function through software programming for enable disable and interval setting General system reset On board Ethernet LAN Two Gigabit Ethernet 10 100 1000 Mbits sec LAN ports using Realtek RTL8111G CG GbE Ethernet Controller High Drive GPIO One pin header for 8 bit GPIO System Monitoring Feature Monitor system temperature and major power s
21. ect the system reliability Note To insure the system stability please do not change any of DRAM parameters in BIOS setup to modify system the performance without acquired technical information WADE 8016 Users Manual 3 5 System Installation 3 3 Installing the Mini ITX Board Computer To install your WADE 8016 into standard chassis or proprietary environment please perform the following Step 1 Check all jumpers setting on proper position Step 2 Install and configure CPU and memory module on right position Step 3 Place WADE 8016 into the dedicated position in the system Step 4 Attach cables to existing peripheral devices and secure it WARNING Please ensure that SBC is properly inserted and fixed by mechanism Note Please refer to section 3 3 1 to 3 3 4 to install INF VGA LAN Audio drivers 3 3 1 Chipset Component Driver WADE 8016 uses Intel Lynx Point It s a new chipset that some old operating systems might not be able to recognize To overcome this compatibility issue for Windows Operating Systems such as Windows 7 please install its INF before any of other Drivers are installed You can find very easily this chipset component driver in WADE 8016 CD title 3 3 2 Intel Integrated Graphics Controller WADE 8016 integrated 3D graphics Media Accelerator WADE 8016 uses Intel Lynx Point integrated graphic chipset to gain an outstanding graphic performance WADE 8016 supports VGA DVI D and HDMI display output
22. eep constantly DRAM error Change DRAM or reinstall it One long beep with twoMonitor or ae e Please check Monitor connector short beeps Card error it i Beep rapidly Power error warning Please check Pow er mam setting Question I forget my password of system BIOS what am I supposed to do Answer You can simply short 2 3 pins on JP4 to clean your password Note Please visit our technical web site at http www portwell com tw For additional technical information which is not covered in this manual you can mail to tsd portwell com tw or you can also ail to our sales they will be very delighted to forward them to us WADE 8016 User s Manual 5 2 Troubleshooting System memory address map Each on board device in the system is assigned a set of memory addresses which also can be identical of the device The following table lists the system memory address used for your reference Memory Area Size Description 0000 003F 1K Interrupt Area 0040 004F 0 3K BIOS Data Area 0050 006F 0 5K System Data 0070 OE2E 54K DOS OE2F 12BE 18K Program Area 12BF 9D7F 555K Available First Meg Conventional memory end at 630K 9D80 9EFF 6K Extended BIOS Area 9F00 9FFF 4K Unused A000 AFFF 64K VGA Graphics B000 B7FF 32K Unused B800 BFFF 32K VGA Text C000 CEBF 59K Video ROM CECO EFFF 133K Unused F000 FFFF 64K System ROM HMA 64K First 64K Extended Interrupt Request Lines
23. etup Information Choices 32M 64M 96M 128M 160M 192M 224M 256M 288M 320M 352M 384M 416M 448M 480M 512M 1024M DVMT Total Gfx Mem Select DVMT 5 0 Total Graphic Memory size used by the Internal Graphics Device Choices 128M 256M MAX Primary IGFX Boot Display Select the Video Device which will be activated during POST Choices VBIOS Default VGA DVI HDMI Secondary IGFX Boot Display Select secondary display device Choices Disable DVI HDMI PCI PCIE Configuration PCI Latency Timer 32 PCI Bus Clocks PCI Latency Timer Value to be programmed into PCI Latency Timer Register Choices 32PCI Bus Clocks 64PCI Bus Clocks 96PCI Bus Clocks 128PCI Bus Clocks 160PCI Bus Clocks 192PCI Bus Clocks 224PCI Bus Clocks 248PCI Bus Clocks WADE 8016 Users Manual 4 9 BIOS Setup Information PCI Express Settings Maximum Payload Ser Maximum Payload of PCI Express Device or allow System BIOS to select the value Choices Auto 128Bytes 256Bytes 521Bytes 1024Bytes 2048Bytes 4096Bytes Maximum Read Request Ser Maximum Read Request size of PCI Express Device or allow System BIOS to select the value Choices Auto 128Bytes 256Bytes 521Bytes 1024Bytes 2048Bytes 4096Bytes CPU PCI Express Configuration PEGO ASPM Disabled PEGO Gen X Configure PEGO B0 D0 F0 Gen1 Gen3 Choices Auto GEN1 GEN2 PEGO0 ASPM Control ASPM support for the PEG Device Choices Disable Auto ASPM L0s
24. he basic system configuration easily This type of information is stored in CMOS RAM so that it is retained during power off periods When system is turned on WADE 8016 communicates with peripheral devices and checks its hardware resources against the configuration information stored in the CMOS memory If any error is detected or the CMOS parameters need to be initially defined the diagnostic program will prompt the user to enter the SETUP program Some errors are significant enough to abort the start up 4 1 Entering Setup Power on the computer and the system will start POST Power On Self Test process When the message below appears on the screen press Del key will enter BIOS setup screen Press Del to enter SETUP If the message disappears before responding and still wish to enter Setup please restart the system by turning it OFF and On or pressing the RESET button It can be also restarted by pressing Ctrl Alt and Delete keys on keyboard simultaneously Press F1 to Run General Help or Resume The BIOS setup program provides a General Help screen The menu can be easily called up from any menu by pressing F1 The Help screen lists all the possible keys to use and the selections for the highlighted item Press lt Esc gt to exit the Help screen WADE 8016 Users Manual 4 1 BIOS Setup Information 4 2 Main Use this menu for basic system configurations such as time date etc System Dat
25. n nennen nennt nna 4 1 4T Bntermp A A 4 1 4 NITE A au a eRe eet nevada ed f oae taU oA Cort ta esent Eo OE nue 4 2 A DX GEV ULE LL OM ce eot ere eno d ae rea hen ciae TCS 4 3 Ah ASA AAA 4 18 A D DECULILY ta 4 20 4 6 OVE Or e te tedeschi REEE dale IIa pa occa ta AUR pede EDI MI esa 4 21 Chapter 5 Troubleshooting common 5 1 5 1 Hardware Quick Installation aea a teo deco 5 1 et REI e mE Een 5 2 Preface How to Use This Manual The manual describes how to configure your WADE 8016 system board to meet various operating requirements It is divided into five chapters with each chapter addressing a basic concept and operation of Mini ITX Board Chapter 1 System Overview Presents what you have in the box and give you an overview of the product specifications and basic system architecture for this series model of Mini ITX Board Chapter 2 Hardware Configuration Show the definitions and locations of Jumpers and Connectors that you can easily configure your system Chapter 3 System Installation Describes how to properly mount the CPU main memory and Compact Flash to get a safe installation and provides a programming guide of Watch Dog Timer function Chapter 4 BIOS Setup Information Specifies the meaning of each setup parameters how to get advanced BIOS performance and update new BIOS In addition POST checkpoint list will give users some guidelines of trouble shooting Chapter 5 Troubleshooting Provide various of useful tip
26. ources Outline Dimension L x W 170mm 6 69 x 170mm 6 69 Power Requirements Item Power ON d CHE ger GE CPU 12V 1 39 1 53 1 55 System 12V 0 67 0 61 0 64 System 3 3V 0 56 0 66 0 67 System 5V 1 51 1 71 1 68 System Device 12V 2 79 2 78 2 76 System Device 5V 1 41 2 42 2 48 USB2 0 Loading Test 4 87 4 94 V 530 mA USB3 0 Loading Test 4 79 V 1060 mA WADE 8016 Users Manual 1 3 System Overview Configuration CPU Type SBC BIOS Memory VGA Card VGA Driver LAN Card LAN Driver LAN Card LAN Driver Audio Card Audio Driver Chip Driver USB 3 0 Driver SATA HDD CFEX CDROM Power Supply Intel Celeron CPU G1820 2 70GHz L3 2M Byte Portwell Inc WADE 8016 APK TEST BIOS 40528T00 WARIS DDR3 UB DIMM 1333 8GB 2 Hynix H5TQ4G83MER Onboard Intel HD Graphics Intel HD Graphics Version 10 18 10 3496 Onboard Realtek RTL8111F PCIe GBE Family Controller Realtek RTL8111F PCIe GBE Family Controller Version 8 20 815 2013 Onboard Realtek RTL8111F PCIe GBE Family Controller 2 Realtek RTL8111F PCle GBE Family Controller 2 Version 8 20 815 2013 Onboard Realtek ALC892 High Definition Audio Realtek ALC892 High Definition Audio Version 6 0 1 7240 Intel H81 Chipset Device Software Version 10 0 13 Intel USB3 0 eXtensible Host Controller Version 6 2 9200 16384 Seagate ST3500411SV 500GB WARIS CFEX 8GB ASUS DRW 24D3ST HG
27. s to quickly get WADE 8016 running with success As basic hardware installation has been addressed in Chapter 3 this chapter will basically focus on system integration issues in terms of backplane setup BIOS setting and OS diagnostics The content of this manual is subject to change without prior notice These changes will be incorporated in new editions of the document The vendor may make supplement or change in the products described in this document at any time System Overview Chapter 1 System Overview 1 1 Introduction Portwell Inc a world leading innovator in the Industrial PC IPC market and a member of the Intel Embedded and Communications Alliance Intel ECA announced today the Portwell WADE 8016 adopting the Mini ITX form factor The WADE 8016 of the Intel platform will provide high performance and flexibility for functional expansion such as Gaming Kiosk DS Medical Defense Industrial automation and control applications Haswell is the next major architecture from Intel The WADE 8016 supports the latest Intel Haswell processors in LGA1150 package which has memory and PCI Express controller integrated to support 2 channel DDR3 memory and PCI Express 2 0 lanes providing great graphics performance Intel Haswell processor is one of the most powerful and energy efficient CPU in the world Portwell have taken advantage of such technology to furnish a series of products that can meet multiple industrial requirements su
28. unction int main Enter Extended Function Mode outp 0x002E 0x87 outp 0x002E 0x87 Enable Pin 77 as WDTO Select Logic Device 8 outp 0x002E 0x07 outp 0x002F 0x08 Active Logic Device 8 outp 0x002E 0x30 outp 0x002F 0x01 Select Count Mode outp 0x002E OxF5 outp 0x002F inp 0x002F amp OxF7 0x00 amp 0x08 Count mode Register 0x00 Specify Time out Value outp 0x002E OxF6 outp 0x002F 0x05 Time out Value Register 0x05 Disable WDT reset by keyboard mouse interrupts outp 0x002E OxF7 outp 0x002F 0x00 Exit Extended Function Mode outp 0x002E 0xAA return 0 j kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk Definitions of Variables Value of Count mode Register 0x00 Count down in seconds Bit3 0 0x08 Count down in minutes Bit3 1 Value of Time out Value Register 0x00 Time out Disable 0x01 0xFF Value for counting down KEE WADE 8016 Users Manual 3 8 System Installation 3 6 GPIO define EFER 0x2e Address for Extended Function Enable Register define DEVICE NUM REG 0x07 Address for Logic Device Number Register define GPIO_LOGIC_NUM 0x08 Logic device number for GPIO define GPIO BASE REG 0x30 Set GPIO define GPIO IO REG 0xe0 Address for GPIO I O Register define GPIO MODE OUT 0 define GPIO DATA REG Oxel Address for GPIO Data Register define MAX GPIO NUM 8 int main int pin num 5
Download Pdf Manuals
Related Search