RF SMART module
Contents
1. 3AF RF SMART ADDITIONAL SECURITY MODULE FORTS CAN USER MANUAL K KEETEC WARNING Carefully readfollowinginstructionsandtechnical specifications producer or seller of the system is responsible for damages caused by incorrect recommend the installation to be made by authorized service SYSTEM DESCRIPTION searching transmitters RC SMART If transmitters not found during 10 seconds the siren chirps 10 times as warning If transmitters not found during next 10 seconds the system is triggered siren hooting and immobilization circuit is still enabled The RF _ turn off the ignition the siren chirps 6 times and LED will start to flash learning mode _ press the button on transmitter System confirm successfully learned transmitter by SMART kit includes antenna harness and RC SMART transmitters DESCRIPTION OF RC SMART TRANSMITTER LED diode Button I SYSTEM FUNCTION The RF SMART offers two working mode immobilization will be disabled and car is able to start engine will be successful the system will be deactivated immobilization will be disabled and car is able to start engine Turn ON OFF auto transmit function range of main unit Ill WIRING DIAGRAM _ Set auto transmit power in this manual before installation The system must be installed and used only according to this manual The system is designed for vehicles with 12V power supply It has to be connected2. to 12V output and to the ground Neither Anytime fast press the button twice and then press and hold it for 2 seconds to set the auto transmit power is grade or Il or Ill or IV The red LED will flash 1 or 2 times or 3 times or 4 times for grade I or Il or Ill or IV i A Note The distance for Grade I is 1 2 meters distance for Grade II is 2 3 meters the installation using or operating of this product Unprofessional operation or modification of the system can damage the system alone or the electric system of the vehicle and leads to warranty loss For proper working of the system we i _TS CAN settings for RF SMART cooperation It is necessary to enable function No 25 in programming table of the TS CAN for correct cooperation with the RF SMART module When function is enabled please The RF SMART is an additional module for car alarm TS CAN which is used to identify an authorized unlocking of the vehicle and subsequent deactivation of immobilisation circuit of TS CAN When car is unlocked doors are opened the system start The system can learning maximum 10 pcs RC SMART transmitters distance for Grade III is 3 6 meters and the distance for Grade IV is 6 8 meters Transmit power grade and ANT location can be set freely as user need to program the RC SMART transmitter into system Programming remote controls activate the service mode see section VIII in TS CAN manual turn on the ignition and press service bu
3. l start to flash again if the LED will flash so many times which is the value of fourth PIN number push the _ service button one time Anytime fast press the button 3 times then press and hold it for 3 seconds LED will flash If you entered correct PIN code siren chirps 4 times and lights flash 2 times and LED once slowly to indicate auto transmit has been turned to on LED flashing twice slowly to indicate auto transmit has been turned to off Not necessary push the button when auto transmit is turned on because immobilizer is deactivate automatically if transmitter is in diode lights permanently The RF SMART will be deactivated RF SMART
4. tton 6 times within 10 seconds siren chirp The siren chirp how many times as numbers of programmed transmitter for exit from learning mode press service button Note When you learning new transmitters the system automatically erase already programmed transmitters Il EMERGENCY DEACTIVATION Open the door and turn on the ignition _ Push the valet button so many times which is the value of the first number in PIN code within 8 seconds and then turn of the ignition default 4321 _ If the security mode is turned off siren chirps 4 times lights flash 2 time The RF SMART will be deactivated lf th it de is activated LED will start to flash slowly Enter th it de 1 For deactivation of TS CAN system is necessary to press the button on the RC sean i tin ica Ba E anos GRO tine eee EHS SMART transmitter Immediately after this the system will be deactivated serice buon one tine LED will start to Hackagain if the LED will flash so many times which is the value of first PIN number push the ifthe LED will flash ti hich is the value of d PIN number push th 2 Auto transmission mode When doors are unlocked and opened and the RC ene ee re i aad SMART transmitter is in range the system tried to identify transmitter If identification service button one time LED will start to flash again if the LED will flash so many times which is the value of third PIN number push the _ service button one time LED wil
Download Pdf Manuals
Related Search