GTI-140 User Manual
Contents
1. ICCONS Connections GTI 140 Insulation GAS TOOL USER MANUAL ICCONS GAS TOOL GTI 140 USER MANUAL Masthead Version 140 RO1 2013 Copyright ICCONS Pty Ltd 12 18 Produce Drive Dandenong South Victoria Australia 3175 Passing on and duplication of this document exploitation and disclosure of its contents are forbidden unless expressly approved Violations render the offender liable to damages All rights reserved for the event of patent utility model or registered design applications This operating manual has been drawn up with the greatest care Nevertheless ICCONS Pty Ltd assumes no liability for possible errors in this operating manual and their consequences Furthermore no liability is assumed for direct or consequential damages resulting from the improper use of the tool The national safety and occupational safety regulations and the safety precautions given in this operating manual must be observed when using the tool All product designations and brand names are the property of their owners and are not explicitly marked as such Amendments to content reserved ICCONS Serious Connections Table of Contents 1 Symbols Used In This Operating Manual 3 2 General Safety Instructions 2 1 Introduction 2 2 Safety Of The Fastening 2 3 Safety At Work 2 4 Safety For Handling Fasteners 2 5 Safety For Gas Operated Nai2. 2 2006 A1 A2 EN 61000 3 3 2008 Having been examined to the requirements of the Electromagnetic Compatibility Directive 2004 108 EC by ICCONS Serious Connections Intertek Testing Services Hong Kong Ltd 2 F Garment Centre 576 Castle Peak Road Kowloon Hong Kong Issued the test verification of conformity number 12100822HKG 002R1 2 EN 60335 2 29 2002 A1 2004 A2 2009 EN 60335 1 2010 Having been examined to the requirements of the Low Voltage Directive 2006 95 EC by Intertek Testing Services Hong Kong Ltd 2 F Garment Centre 576 Castle Peak Road Kowloon Hong Kong Issued the test verification of conformity number 13070126HKG 003 13070126HKG 004 3 EPS IM 278 2009 Having been examined to the requirements of the Energy related Products Directive 2009 125 EC by Intertek Testing Services Hong Kong Ltd 2 F Garment Centre 576 Castle Peak Road Kowloon Hong Kong Issued the test verification of conformity number 1307128HKG 001 16 ICCONS GAS TOOL 140 USER MANUAL ICCONS 11 Copyright 12 Disposal Copyright Recycle the tool and its packaging in ICCONS Pty Ltd an environmentally friendly manner in 12 18 Produce Drive Dandenong South accordance with the recycling regulations Victoria 3175 Australia applicable in your country Passing on and duplication of this document exploitation and disclosure of its contents are forbidden unless expressly approved Violations render the offen
3. and encourage breathing Should the casualty become unconscious or breathing does not quickly return to normal summon urgent medical assistance If gas gets into the eyes they should be flushed out with copious amounts of water Skin contaminations should be removed with soapy water symptoms persist seek medical assistance ICCONS GAS TOOL 140 USER MANUAL ICCONS 4 Use Of The Battery amp Charging System Introduction The adaptor charger and the battery are designed to operate together as one system Only use the ICCONS Pty Ltd Adaptor amp ICCONS Pty Ltd Charger for charging the ICCONS Pty Ltd Batteries The charging system is intended to be used in covered areas Do not expose it to rain or to excessive humidity Do not recharge non rechargeable batteries 4 1 Before Charging Arrange the adaptor output lead appropriately to avoid unnecessary damage avoid laying output lead across walkway or doorway Check the system before use if cable or plug damaged do not use for charging battery and replace it immediately Keep the charger exhaust area clean and unblock to have the best cooling effect Use dry cloth to clean the body and the contact of the charger or adaptor while it disconnected with the main power Charge the battery in room temperature If its temperature is less than 5 C or greater than 40 C will degrade the battery charging performance If the batte
4. any loose fasteners or defects on the tool before use Only use the tool for nailing application for which it was designed It is not permitted to make any modification to the tool fuel cell or battery other than those specified by the manufacturer If the tool is weakened or damaged by punching or engraving modification not authorized by the manufacturer guiding against templates made of hard material dropping or pushing across the floor use as a hammer apply excessive force of any kind it should be taken to service and inspect by the manufacturer or authorized agents Operator should carry out regular ICCONS GAS TOOL 140 USER MANUAL maintenance cleaning and lubrication in accordance with the operation manual to keep the tool in good working order The fastener driving tool should be serviced properly and at regular intervals in accordance with the operation manual 2 3 Safety At Work WARNING Always assume the tool is loaded Never point any tool at vourself or at any other person Make sure the workplace is clean and well lit Stay alert watch what are you doing and use common sense when operating the tool Do not use tool while tired or under the influence of drugs alcohol or medication The tool must be carried pointed downward while moving locations Never carry the tool with your finger on the trigger Never press your hand on the front of the tool The tool must be opera
5. for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure PLEASE RETAIN A COPY OF THE TAX INVOICE FOR YOUR WARRANTY OWNERS COPY AND RECORD original purchase receipt is still required for claims SERIAL No ICCONS Pty Ltd Ol Connections 12 18 Produce Drive Dandenong South Victoria 3175 Australia Tel 61 03 9706 4344 Fax 61 03 Email info iccons com au Web www iccons com au This manual must be observed when using the tool All product designations and brand names are the property of their owners and are not explicitly marked as such Amendments to content reserved 19
6. not been subjected to misuse beyond the recommendations limitations specified and as outlined in the ICCONS GTI140 User manual neglect been damaged modified or repaired without the approval of ICCONS e The tool is presented on return in a condition that displays it has been cleaned and serviced as outlined in the ICCONS 140 User manual e Repairs to the tool are not required as result of normal wear and tear eg Piston Piston Rings WHERE LAWFUL UNDER NO CIRCUMSTANCES SHALL ICCONS PTY LTD BE LIABLE FOR INCIDENTAL CONSEQUENTIAL SPECIAL DAMAGES OR DIRECT OR INDIRECT LOSS OF ANY KIND INCLUDING BUT NOT LIMITED TO BODILY INJURY DEATH OR PROPERTY DAMAGE ICCONS ENTIRE LIABILITY IS LIMITED TO THE PURCHASE PRICE OF THIS PRODUCT If you wish to make a warranty claim then the tool or part must be returned to ICCONS Pty Ltd at the owner s expense ICCONS will inspect the returned tool parts and at its own option may replace the tool parts and return it to the owner at its own cost if deemed to fall within the scope of the warranty conditions ICCONS Pty Ltd cannot be held responsible for any repair other than those carried out by it or one of its Authorised Service Agents IMPORTANT NOTE FOR AUSTRALIAN CONSUMERS Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to replacement or refund for a major failure and for compensation
7. the trigger is not held while inserting fuel cell e Empty fasteners in the magazine before installing fuel cell e Do not press on the surface ground while installing Steps 1 Push up and pull to open the fuel door 2 Insert the fuel cell direct the jet nozzle into the adaptor 3 Put the can door over the valve and push it down to latch 4 For removing fuel cell reverse the above steps 5 6 Installing amp Removing Barrel 01 4 Sy 2 Caution e sure the trigger is not held while inserting barrel e Do not press on the surface ground while installing e Do not cover the barrel with your hand while installing Steps 1 Press down and hold the adapter for barrel 2 Insert the barrel and release the adapter 3 Rotate the barrel until the adapter returns to its original position 4 For removing press and down the adapter and pull the barrel out ICCONS GAS TOOL 140 USER MANUAL 5 7 Loading The Pins c 4 Caution e sure the trigger is not held while loading the pins e Do not press on the surface ground while loading Steps 1 Insert the insulation fastener into the barrel until it reaches the tip of pin guide 2 For removing the insulation fastener simply pull the fastener out from the barrel 5 8 Driving The Pins 5 Caution e Please READ and UNDERSTAND the section General Safety Instructions for personal and working envi
8. L GTI 140 USER MANUAL ICCONS SYMPTOM 3 SYMPTOM 2 Fan runs intermittently Failure to install fasteners to nose piece Possible Possible reasons reasons Battery is loose or contacts are bent SYMPTOM 1 Snap battery back into Piston Return piston to original its locked position Bend positioned position according to contacts back into proper wrongly User Manual position O Ring is Contact authorized 6 3 Pre Combustion Combustion damaged and serviceman for repair Stage of Operation causing leakage of gas Some dirt Contact authorized Contact Arm does not depress fully tool does on the valve serviceman for repair not operate Possible reasons Lockout Bar is stuck in lockout position The nose piece is bent or the channel is stuck with dirt Follower holder positions wrongly Cylinder head Contact authorized O Ring pinched serviceman for repair Jammed Clear jam according to fasteners User Manual washer inside cylinder Valve wave Contact authorized washers lose serviceman for repair Check if there is not elasticity enough pins in the channel load extra pins according to Operating SYMPTOM 3 Manual Tool will not cycle fan runs Inspect if the nose Possible piece and channel is reasons clean If it is damaged Fuel Cell is Replace Fuel Cell consult authorized em pty serviceman for repair and replacement of the Spark does not Contact authorize
9. RETAINING RING ROUND HEAD SCREW COMBUSTION CHAMBER AIR DAM U WIRE PISTON STOP PISTON STOP RUBBER HEAD O RING BLADE ASSEMBLY CYLINDER HEAD SPARK PLUG FUEL NOZZLE MOTOR SLEEVE MOTOR BUMPER MOTOR MOTOR GUIDE CONNECTOR BOARD MOTOR HOLDER SPRING WASHER ROUND HEAD SCREW HOOK amp TRACK LOCK 2 BE Washer 12mm Or JE 3 N F100 MD Ww N ICCONS GAS TOOL 140 USER MANUAL 10 Declaration Of Conformity With regard to the Machinery Directive 2006 42 EC The manufacturer distributor ICCONS Pty Ltd 12 18 Produce Drive Dandenong South Victoria 3175 Australia Declare under our sole responsibility that the products A Gas powered nailer with removable magazine with reference to model GTI 140 conforms to the following standards or normative documents 1 EN 792 13 2000 A1 2008 Hand held non electric power tools Safety requirements Part 13 Fastener driving tools Having been examined to the requirements of the Machinery Directives 2006 42 EC by Safenet Limited Notification 1674 c o Denford Garage Denford Kettering Northamptonshire 14 260 UK Issued the EC examination certificate TBA with available technical file copy for the equipment B AC DC adaptor charger amp battery with reference to model GT BCU GT BCP BCA1215 conforms to the following standards or normative documents 1 EN 55014 1 2006 A1 A2 EN 55014 2 1997 A1 A2 EN 61000 3
10. WAY FROM SMOKE AND FIRE WEAR EAR PROTECTION gt gt OP WEAR EYE PROTECTION USE PROTECTIVE HAND WEAR 2 GENERAL SAFETY INSTRUCTIONS WARNING Read all safety warnings and instructions Failure to comply with the safety warnings and instructions can result in severe injuries O Keep all safety warnings and instructions for future use This appliance is not intended for use by person including children with reduced physical sensory and mental capabilities or lack of experience and knowledge ICCONS Serious Connections The ICCONS Pty Ltd Gas Nailer is referred to as tool in this general safety instruction ICCONS Pty Ltd is referred to as manufacturer in this general safety instruction 2 1 Introduction Only those fasteners which are specified in the operating instructions shall be used in the tool The tool the fastener the fuel cell and the battery specified in the operating instructions are to be considered as one unit safety system Only spare parts specified by the manufacturer or his authorized representative shall be used in the service or repair of the tool Repairs shall be carried out only by the manufacturer or his authorized representative Keep the tool fasteners fuel cell battery and charger out of the reach of children 2 2 Safety Of The Fastener Driving Tool Check prior to each operation that the safety mechanism is functioning properly Rectify
11. contains pre mixed fuel and lubrication No extra lubrication required Warning Only specified Fuel Cell and Lubricant by ICCONS can be used on the tools please consult the ICCONS agents or local distributors Dimensions Insulation Thickness 25 140 mm Pin Head Diameter 06 3 mm Pin Length 47 52 mm Shank Diameter 93 65 3 2 mm Applications Insulation Thickness 25 140 mm Only those fasteners which are specified in this specification shall be used in ICCONS Pty Ltd Gas Tools The ICCONS Pty Ltd Gas Tool and the fasteners specified are to be considered as one unit safety system 13 ICCONS Serious Connections The adaptor charger and the battery are designed to operate together as one system 7 4 AC DC Adaptor Model No 1215 BCA1215 ANC TYPEI AS NZ BCA1215 EU EU BCA1215 UK UK BCA1215 US TYPEA US Input 100 240V 0 6A Max 50 60Hz Output 12VDC1 5A 7 5 Battery Charger Unit Model No GT BCU Input 12V 0 1 5 Output 7 3 DC 700mA Charging Time 2 5 Hours Battery Type ICCONSB6VMH Model No GT BCP Type Ni MH Output 6V DC Capacity 1 5Ah 5 cells 8 Tool Serial Number Located on the tool handle near the track connection YY MM XXXX YY Year of construction last two digits MM Month of construction Tool serial number ICCONS GAS TOOL 140 USER MANUAL ICCONS 9 Parts List 151405 1 20131021 M O 4 5
12. d parts occur serviceman for repair Slide gently the follower holder to the bottom and release SYMPTOM 4 Fail to drive fasteners Possible reasons Water vapour Dry the spark area or surrounding contact authorized Spark causing serviceman for repair short circuit Sealing pad Contact authorized damaged serviceman for repair Piston guide Contact authorized stuck with dirts serviceman for repair 11 ICCONS GAS TOOL GTI 140 USER MANUAL 6 4 Power Exhaust Stage of Operation SYMPTOM 1 Tool operates properly but fasteners do not drive fully Possible reasons Battery is Charge battery discharged Fuel Cell is low Replace fuel cell according to User Manual SYMPTOM 2 Tool operates but no fastener is driven Possible reasons Fastener strip Use only fasteners may be binding meeting designated specifications Follower holding Slide follower holder gently to the bottom and release to reset the pin strip in the magazine wrong at the top of the pin strip Jammed Clear jam according to fasteners User Manual SYMPTOM 3 Operation of the tool is not stable Possible reasons Fuel Cell is low Replace fuel cell according to User Manual Spark Plug wire Contact authorized is loose serviceman for repair Filter element Remove filter element is dirty causing and clean according to tool to overheat User Manual Contact authorized serviceman for r
13. der liable to damages All rights reserved for the event of patent utility model or registered design Separate collection Local regulations may provide for separate collection of electrical products from the household at municipal waste sites or by the retailer when you purchase the new This operating manual has been drawn product up with the greatest care Nevertheless Separate collection ICCONS Pty Ltd assumes no liability for OY packaging and failed possible errors in this operating manual and o rechargeable battery their consequences Furthermore no liability in accordance with the is assumed for direct or consequential ug edine damages resulting from the improper use of applicable in your country the tool The national safety and occupational safety regulations and the safety precautions given in this operating manual must be observed when using the tool All product designations and brand names are the property of their owners and are not explicitly marked as such Amendments to content reserved 17 ICCONS GAS TOOL GTI 140 USER MANUAL ICCONS Serious Connections ICCONS Pty Ltd warrants the original purchaser of the GT1140 against defective workmanship and faulty materials for 12 months from date of purchase It is a condition of the warranty period that e Proof of original purchase and ownership including address and phone number must be provided e The GTIL40 has
14. ent The tool must be used in well ventilated areas Exhaust gases in a confined space can be hazardous Do not use the tool outside in the rain or where excessive moisture in present Keep the tool from heat sources as the pressurized fuel cell could be damaged Do not smoke when handling the fuel cell Keep away from your face and eyes Do not inhale its content The temperature of the tool may increase depending on the firing frequency Observe the maximum cycle rates given in the operating instructions ICCONS GAS TOOL GTI 140 USER MANUAL 3 Use Of The Fuel Cell DANGER KEEP FUEL CELL AWAY FROM SMOKE AND FIRE WARNING LIQUID GAS CAN CAUSE INJURY IN THE CONTACT WITH THE SKIN OR EYES WARNING FUEL CELL CONTENTS ARE EXTREMELY FLAMMABLE WEAR EYE PROTECTION USE PROTECTIVE HAND WEAR Introduction The fuel cell is an aerosol product corresponding to the 2008 47 EC regulations It contains Liquefied hydrocarbon gases Butane amp Propane Lubricant to help tool work smooth 3 1 Safety for Handling the Fuel Cell The fuel cell is always pressurized with propellant to sustain the fuel supply to the metering valve even if the fuel is used up Its contents are extremely flammable The fuel cell is not reusable Do not attempt to refill Do not spray towards a flame or an incandescent body Keep away from any heat sources and from electrostatic charges Do not smoke w
15. epair Tool sleeve or O Rings are dirty ICCONS Serious Connections SYMPTOM 4 Unstable performance Possible reasons Contact authorized serviceman for repair Built up dirt and debris inside cylinder SYMPTOM 5 Diminishing power Possible reasons Damaged Contact authorized piston or serviceman for repair cylinder 6 5 Returning Purging stage of Operation SYMPTOM 1 Tool operated and drove fastener but piston did not return to up position Possible reasons Mushrooming Contact authorized of Piston Tip serviceman for repair Exhaust ports on Contact authorized the sleeve are serviceman for repair dirty or clogged Contact authorized serviceman for repair Tool Sleeve or O Rings are dirty SYMPTOM 2 Combustion Chamber does not drop after tool cycles Possible reasons Contact armis Clean tool or replace bent or toolis contact arm as require dirty 12 ICCONS GAS TOOL 140 USER MANUAL 7 Technical Specification Model No GTI 140 Dimensions Length 530 mm Height 120 mm Width 360 mm Weight 4 2 kg Recommended Usage 600 Hr 3 000 Day Vibration The vibration mechanical impact risk is low it is the users responsibility to ensure that the operators are not put at risk due to environmental and work piece specifications PAT Ke Model No FC165G Dimensions Height 165 mm Diameter 32mm Pressure 18 bar Capacity 700 shots Fuel cell
16. gt n O O a A lt gt 2 gt CSM cove NB4010 NB4420 baa NB4410 NB1040 NB1050 NB2060 NB1070 NB2Z10 NB2Z20 NB1780 NB2Z30 NB2130 NB1Z40 NB1Z50 set NB210B NB1290 NB1170 NB1380 NB1370 NB2Z60 NB1180 NB1220 NB1310 NB1270 NB2Z70 NB1200 NB1300 NB1260 NB1Z80 Prec NB2430 NB1440 NB2450 NB1470 NB1480 2790 NB2520 NB2460 Eas NB2530 DESCRIPTION PIN GUIDE GUIDE SLEEVE NOSE PIECE SOCKET SCREW BUSHING DUST SHIELD SHIELD SPACER HOUSING HEAD COVER SOCKET SCREW HANDLE FIRING CAM FUEL DOOR BUSHING SOCKET SCREW METAL WASHER LOCKNUT METAL WASHER SOCKET SCREW CONTROL UNIT ELECTRODE ASSEMBLY TRIGGER SWITCH MOTOR SWITCH SELF TAP SCREW TRIGGER WITH SPRING TRIGGER SPRING SWITCH LEVER SWITCH PLATE BATTERY LOCK CAGE CAGE SPRING RETAINING RING WAVE WASHER VALVE WASHER CYLINDER ASSEMBLY CYLINDER O RING VALVE COVER BUMPER CODE 4700 2550 2560 2570 2580 2600 2590 2920 2930 4 0 m 2610 1620 2630 1650 2660 1670 1680 1690 1700 1641 1710 1720 1730 6 2140 5 D a M5 x 25 5 x 30 M5 x 14 M5 x 16 M4 x 16 23 9 M5 x 10 M4 x 20 1 a LOCTITE BLUE LOCTITE RED 15 ICCONS Serious Connections DESCRIPTION PISTON WITH RING PISTON RING
17. hen handling or loading fuel cells Do not expose to temperatures exceeding 50 C Store and use the cartridge in a well ventilated area only Do not inhale Do not pierce or burn the cartridge after use Keep away from children ICCONS Serious Connections Dispose of only in designated places For optimum performance use before the date indicated at the bottom of the cartridge 3 2 Transport The regulations by transport categories are Road Rail ADR RID UN code 2037 class 2 1 Sea IMDG UN code 2037 class 2 1 EmS F D S U Air IATA UN code 2037 class 2 1 Goods must be accompanied a transport emergency card for road UN 2037 Transport by post is not permitted 3 3 Storage Stores and showrooms must comply with building regulations All local instructions corresponding to fire regulations must be followed Where possible store fuel at stable temperature in the range 5 to 25 C Do not expose to temperatures exceeding 50 C Do not use a tool that emit flames sparks or reach high temperatures in the vicinity that fuel cells are stored Do not store in designated thoroughfares hallways or stairwells Stores in a well ventilated area Fuel cells must not be displayed in shop windows Storage with pyrotechnic products is not permitted 3 4 First Aid Direct contact with liquid gas may cause burns or frostbite In case of inhalation remove the person to fresh air
18. ler Tool 3 Use of the Fuel cell w PF P Aww 3 1 Safety for Handling the Fuel Cell 5 3 2 Transport 5 3 3 Storage 5 3 4 First Aid 5 6 4 Use Of The Battery amp Charging System 4 1 Before Charging 6 4 2 Safety For Handling Battery 6 43 Storage 6 5 1 Charging 6 5 2 Installing amp Removing The Battery 7 5 3 Battery Light Indicator 7 5 4 Preparing The Fuel Cell 8 5 5 Installing amp removing Fuel Cell 8 5 6 Installing amp removing Barrel 8 5 7 Loading The Pins 9 58 Driving The Pins 9 59 Cleaning the Filter 9 6 Troubleshooting 10 61 Battery Charger Problems 10 6 2 Normal Stage of Operation 10 6 3 Pre Combustion Combustion Stage 11 6 4 Power Exhaust Stage of Operation 12 6 5 Returning Purging stage of Operation 12 7 Technical Specification 13 71 Gas Nailer 13 7 2 Fuel Cell 13 73 Fastener 13 74 AC DC Adaptor i 7 5 Battery Charger Unit 13 76 Battery Cell Pack 13 8 Tool Serial Number 9 Parts List 10 Declaration Of Conformity 11 Copyright 12 Disposal 13 Warranty ICCONS GAS TOOL 140 USER MANUAL 1 Symbols Used in this Operating Manual WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS TO REDUCE THE RISK OF INJURY READ THE INSTRUCTION MANUAL BEFORE USE DANGER THE TOOL MUST NOT USED IN A COMBUSTIBLE ENVIRONMENT OR CONFINED SPACE WARNING CHECK THE SAFETY YOKE IS FUNCTIONAL ON EVERY OPERATION It must reliably return to its starting position WARNING KEEP TOOL A
19. n tool indicator lights after 3 hours on charge on charger cycle If tool functions properly charger lights are not working correctly Replace charger or monitor time to ensure Battery Cell has adequate time for recharging It s normal for Battery to feel warm after properly charging Discontinue use immediately and unplug from power source Replace charger and tag or dispose of charger to prevent accidental reuse or connection to power source Damaged charger SYMPTOM 2 Red and green LEDs on charger are blinking alternately Possible reasons ICCONS Serious Connections Battery is hot Remove battery from charger and allow to cool Inspect battery charger and cartridge SYMPTOM 3 Red and green LEDs on charger are blinking simultaneously Possible reasons Battery Replace Battery damaged or cycle life exhausted 6 2 Normal Stage of Operation SYMPTOM 1 Fan does not run Possible reasons Battery is not Charge Battery according charged to Operating Manual Battery Clean Battery Cell Terminals or terminals Clean Handle Handle battery Battery Cell contacts as contacts are required oily dirty or corroded The tool must be looked into by Authorized Serviceman There is electrical short somewhere SYMPTOM 2 Fan does run or runs slower than normal Possible reasons 10 Battery is Charge Battery Cell discharged ICCONS GAS TOO
20. per AC voltage source both green and red light will remain alight 2 Insert the battery into charger red light will alight indicating the battery is charging 3 It takes about 2 5 hours for charging 4 When fully charged green light will remain alight 5 After charging unplug the charger from ICCONS GAS TOOL GTI 140 USER MANUAL the power source e both lights are blinking in same remove the battery cartridge and plug again e If this happens continuously the battery cartridge may be damaged Consult authorized serviceman for replacement of new battery cartridge NOTE e Never attempt to open the charger battery cartridge e The battery charger is for charging specific battery pack Never attempt to charge battery pack from other manufacturer s battery cartridge Unsuitable battery cartridges may cause fire that causes injury e When the battery charger is being used keep out of direct sunlight e get better cooling effect keep the exhaust area Clean 5 2 Installing amp Removing The Battery Green LED light blinks every 0 5 sec under working condition Red LED blinks every 4 sec or keep alighted under working condition Red LED blinks every second The tool has entered protection mode NOTE being fired Steps 1 Empty fasteners from the magazine and make sure the trigger is not pulled while installing the battery 2 To install the battery insert
21. ronment Safety e If you spot of any abnormality about the tool contact nearest authorized serviceman for inspection and repairing Steps 1 Press the tool with suitable length of insulation fasteners through the insulation material 2 Press the Nose of the contact arm against working surface 90 against the ICCONS Serious Connections surface firmly until you hear the fan motor is working 3 Pull the trigger the pins are driven to the object 4 Release the trigger and lift the tool 5 9 Cleaning the Filter The filter at the back of the tool acts crucially to suck in air into the chamber For maintaining the best performance of the tool users should always keep it clean 1 Unscrew four screws on the back cover 2 Take out the back cover and clean the mesh with brush or air 3 Put the back cover on the machine and fasten with four screws NOTE Do not attempt to use water to clean the mesh The cover and mesh must be dry when operating the tool If wet it may easily cause malfunction to the tool ICCONS GAS TOOL GTI 140 USER MANUAL 6 Troubleshooting WARNING To reduce the risk of serious personal injury ALWAYS unload the battery the pins and fuel cell from the tool before all re pairs 6 1 Battery Charger Problems SYMPTOM 1 Battery Cell does not appear to accept charge Green charger light does not come on after several hours Possible reasons Inoperative Try Battery i
22. ry charger abnormally heats up or gives off fumes during charging disconnect the charger and separate with the battery immediately This appliance is not intended for use by person including children with reduced physical sensory and metal capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance 4 2 Safety For Handling Battery Do not short circuit the battery pack Do not pierce or open the battery pack Do not store the batteries ata temperature above 50 C Do not incinerate spent batteries Only charge one battery at a time Batteries and charging systems must be recycled or taken to a designated disposal area 4 3 Storage Store the batteries in a cool and dry place Over discharge will degrade the batteries capacity Fully charged the batteries if stored for along time Recharge it in each 3 months can help to compensate the self discharged and keep the battery in a good condition The charging systems should store at a place out of reach of children Children should be supervised to ensure that they do not play with the appliance Always disconnect the batteries with tools or charger while stored 5 Tool Operation 5 1 Charging Steps 1 Plug the battery charger into the pro
23. ted only when it is in contact with the material to be fixed The operator must be in a stable position when using the tool Operate the tool in the manner that should the tool recoil there is no risk of injury to the operator When using the tool the operator and any bystanders must wear appropriate eye and ear protection When not in use remove the battery fuel cell and fasteners return the fastener follower to guide locking position and return the tool to its carrying case 2 4 Safety for Handling Fasteners Do not load the fasteners with the trigger and or work contacting element pressed Ensure that you use the correct length of fastener with the depth adjuster correctly set so that nails do not protrude when a fixing is made Do not drive fasteners on top of other fasteners Never drive fasteners into free space or ICCONS Serious Connections areas with concealed hazards This will avoid a hazard caused by free flying fasteners and excessive strain of the tool Take particular care when nailing close to edges as fasteners can break out and deflect out of the substrate If tool jams or misfires always remove the battery and fuel cell prior to examination of the tool If the problem persists stop operating the tool unload the fasteners and contact the manufacturer or authorized agents for service 2 5 Safety for Gas operated Nailer Tool The tool must not be used ina combustible environm
24. the battery cartridge until hearing a click 3 Turn and lock the battery to avoid loosen during shooting 4 To remove the battery turn to unlock grip the button at the back of battery cartridge and pull out 5 3 Battery Light Indicator ICCONS Serious Connections Battery level sufficient for working Low battery level need to unplug and recharge immediately Stop using the tool immediately and consult authorized serviceman for maintenance After using the tool remove the battery from the tool to prevent the tool from ICCONS GAS TOOL 140 USER MANUAL 5 4 Preparing The Fuel Cell amp 04 Caution e Never attempt to use fuel cell from other manufacturer e Do not remove the cap when it is unused e Never drill a hole on the fuel cell e Do not inhale the gas Breathing in the gas could cause sleepiness dizziness or nausea e The fuel cell is not refillable do not attempt to refill the gas Steps First ensure to use the correct colour valve the colour of the rim for 15140 should be green 1 Detach the cap attach the valve by pushing in the front edge 2 Pushing the rear edge until it has clicked NOTE e sure the fuel cell valve is attached firmly if not gas leakage may occur and create hazards to users and bystanders ICCONS Serious Connections 5 5 Installing amp Removing Fuel Cell 7 Caution e Make sure
Download Pdf Manuals
Related Search