Pellet boilers User MANUAl - La Nordica
Contents
1. ENGLISH 5 OExtraflame INTRODUCTION The boilers produced in our factory are built with attention to the individual components so as to protect both the user and the installer from any accidents It is therefore recommended that after any intervention on the product the authorised staff pay particular attention to the electric connections especially the stripped parts of the wires These must not escape from the terminal board in any situation thus preventing possible contact with the live parts of the wire The instruction manual is an integral part of the product make sure that it always accompanies the appliance even if transferred to other owners or user or is transferred to another place If it is damaged or lost request another copy from the area technician This generator must be intended for the use it has been specifically made for The manufacturer is exemptded from any liability contractual and extracontractual for injury damage caused to persons animals and objects due to installation adjustment and maintenance errors and improper use INSTALLATION Installation of the generator and auxiliary equipment in relation to the heating system must comply with all current Standards and Regulations a2. n 41 Sow 2 2 0 lt o m Y m DN Y ES 223 x A 2 8 1 gt Q v 7 Q gt v S m Q 5 gt E 2 2 CO 2 a3 7 D TE lt e omi Ea GE E Y ue 4 AE 4 Li ME 272 EN gt A 25 o c LES 2 L E 5 Vv a D D 1 vc n 2 Y v a 9 i S s X ow ues Lo a E 2 na A bd FE 27 E H 2 D U S 7 ps ah A ae Py d 7 Y 2 D A BE REFERENCES NON INFLAMMABLE OBJECTS REFERENCES NON INFLAMMABLE OBJECTS ENGLISH 7 OExtraflame We thank you for having chosen our company our product is a great heating solution developed from the most advanced technology with top quality machining and modern design aimed at making you enjoy the fantastic sensation that the heat of a flame gives in complete safety WARNINGS This instructions manual is an integral part of the product make sure that it always accompanies the appliance even if transferred to another owner or user or if transferred
3. 26 DECOMMISSIONING END uos Ea TE ada MS 26 bk Wl S m 28 iN Te M 29 ENGLISH 3 OExtraflame SPECIFICATIONS FEATURES 1304 1408 NA N O UJ Width 560 560 780 Dept 685 2 Exhaust tube diameter 120 Air intake tube diameter Max global thermal power 16 9 Rated output thermal power made with water 15 2 Min global thermal power Min thermal power output Max hourly fuel consumption 8 5 Min hourly fuel consumption Pellet tank capacity 120 120 Un 3 UJ EM T EA N 59 9 22 5 UJ UJ Recommended chimney draught 1410 A p BS o Ri T A IN E PX N N 7 22 Rated electric power Electric power to Q 100 100 110 Electric power to 120 120 130 Stand By power N UJ N UJ N UJ Rated voltage O Un O O Rated frequency Water inlet outlet tube diameter N NO NO Automatic exhaust tube diameter Pump head rating NA NA U1 Maximum operating water pressure allowed Min operating water pressure allowed ar C 56 5 62 7 Flue gas temperature at reduced
4. 10 REARM m 10 FEATURE m 10 TRE TCA TG T A A n 11 Sis jr m 11 PELLETS AND PEE cp R G CR X 13 CHECKS AND PRECAUTIONS FOR FIRST IGNITION se scsisiccsstesccactscscessesesccecescssssensansacscsaneaesstessansseseaasesdevcaessansiseseaventesdhscuussesssUescaseasseenseasacve 13 THE PELLET ELOADING MOTOR DOES NOT WORK HUVEC E IUE 13 TOUCH SCREEN DISPLAY peer 2 0 428 2642632060 6422546123222444432240012250 31214422001240220 222 22232424431340426 24 02501302 14 CONTROL PANEL AND ICONS e M m 15 KEY FUNCTION pcr M 16 MENU STRUCTURE 16 eo nce 16 COMMISSIONING 5 se ninao iuan a aiaa a aSa S EN Sa au En Naa EENEN Sai 17 MAINS FREQUENCY 30 00 Fm ani a aA 17 SEEE E E M 17 eX EI
5. HP15 22 30 TF FEATURES Water content of the thermo product heat exchanger 1 Volume of expansion vessel integrated in the thermo product 1 3 bar safety valve integrated in the thermo product Minimum and maximum pressure switch integrated into the thermo product Pump integrated into the thermo product i ENVISION A POSSIBLE ADDITIONAL EXPANSION VESSEL DEPENDING ON THE SYSTEM WATER CONTENT Head m UW The diagram to the side illustrates the behaviour of the pump 0 EEEEEECEEEPER ES used on our thermo products at the speeds that can be set 0 0 5 1 1 5 2 2 5 3 3 5 Flow rate m h 10 ENGLISH OExtraflame INSTALLATION GENERAL The flue gas exhaust and hydraulic connections must be carried out by qualified personnel who must issue installation conformity documentation compliant with national standards The installer must provide the owner or person acting for him according to the legislation in force with the declaration of conformity supplied with 1 the use and maintenance manual of the appliance and of the system components such as for example the smoke ducts chimney etc 2 photocopy or photograph of the chimney plaque 3 system booklet where applicable The installer must ask to be issued wit
6. Sn 21 CARON m M M ete acece 22 ts 22 BEI eT 22 gel eT M P 23 OTHER FUNCTIONS e 23 AR BE ORAR enm 23 23 COMBUSTION CHAMBER CLE AINIING 23 TEOGA D Tear eee eer er ee eT er er ee ere ere E ee rr er 23 CLEANING AND DENA NCE 24 MAINTENANCE 24 GCLEANINGAND MAINTENANCE BY THE 24 ROUTINE MAINTENANCE PERFORMED BY QUALIFIED TECHNICIANS
7. 3 mt 7 Insulated T fitting with inspection plug A 3 5 fitting Condensation proof with T fitting with inspection inspection plug plug Q d CONNECTION TO THE MAINS ELECTRIC SUPPLY The generator is supplied with an electric power cable to be plugged into a 230V 50 Hz socket possibly with a circuit breaker switch The Socket must be easily accessible The electrical system must be compliant with standards The efficiency of the earthing circuit must be checked Unsuitable earthing of the system can cause malfunctioning for which the manufacturer will not be held liable Power supply variations beyond 1096 can cause faulty operation of the product 12 ENGLISH OExtraflame PELLETS AND FEEDING Pellets are made by applying high pressure to sawdust or wood waste products not containing paint from sawmills carpentry and other activities related to processing and working with wood Given that it does not use any glue to hold it together this type of fuel is completely environmentally friendly In fact the compactness of the pellets over time is guaranteed by a natural substance found in the wood itself wood coal In addition to being an environmentally friendly fuel in that it pushes wood residues to
8. Hmc T 17 OPERATION LOGICS 18 STBY ADDITIONAL ROOM THERMOSTAT 2 19 ADDITIONAL ROOM THERMOSTAT FUNCTIONING WITH STBY ACTIVE STBY ON sesssssssscssecssessscssscuscssscssscusecsecsssesscssccsscensecuscnsceusesueessecnsesseesseeses 19 OPERATION OF THE AMBIENT ADDITIONAL THERMOSTAT WITH STBY DISABLED 5 19 AUK qu M 19 SET POWER C 20 SET TEMPERATURE eter Ese 20 USER REGULATION p 20 PORN POTCEEA NIN Toisia a E O T EE E E E N E EE E 20 TANE 20 siis CHR ON MN A E 21 pe E E AE E E E E E E EEE 21 U ee M M Mm 21 E
9. Extraf fame Riscaldamento a Pellet PELLET BOILERS USER MANUAL HP 15 22 30 ENGLISH INGLESE OExtraflame 2 ENGLISH OExtraflame 222531555552 54555522453342 4552 42225 522 33255244223355455425255543325252420 818 532252515 533236522354 442 55215228553535482525444434 15452 555 248522284442333 4 1 202 OF COMPONENT S INTRODUCTION E M 6 RECOMMENDED DISTANCES FOR THE BOILER 7 WARNINGS 8 SAPET I 2 05 90 90830 0023 0050 000 00 08 50 00 0 B9 E cui Red Use UR Es ee OUR eue eB eae de 8 ROUTINE MAINTENANCE 8 FEY DRUG STS 9 IS TALEATIOBN AND SAFETY DEVICES 9 ANTI CONDENSATION DEVICE MANDATORY 9 E O O A
10. ACTIVE STBY ON When the contact or the external thermostat is satisfied open contact temperature reached the generator will switch off As soon as the contact or external thermostat switches to the not satisfied status closed contact temperature to be reached it will re ignite PLEASE NOTE the generator operation depends on the temperature of the water inside the thermal product and relevant factory setting If the generator is in H OFF water temperature reached any additional contact or thermostat request will be ignored OPERATION OF THE AMBIENT ADDITIONAL THERMOSTAT WITH STBY DISABLED STBY OFF When the contact or external thermostat is satisfied open contact temperature reached the generator will go to minimum As soon as the contact or external thermostat switches to the not satisfied status closed contact temperature to be reached the generator will start to work again at the pre set power PLEASE NOTE the generator operation depends on the temperature of the water inside the general and relevant factory setting If the generator is in H OFF water temperature reached any additional contact or additional thermostat request will be ignored ADDITIONAL ROOM THERMOSTAT INSTALLATION Switch the appliance off using the master switch positioned on the rear of the generator Remove the plug from the socket Refer to the electrical diagram to connect the two thermostat cables onto the relative clamps positione
11. BE CHECKED TO ENSURE THAT THEY DO NOT PLAY WITH THE APPLIANCE DO NOT TOUCH THE GENERATOR WHEN YOU ARE BAREFOOT OR WHEN PARTS OF THE BODY ARE WET OR DAMP THE SAFETY AND ADJUSTMENT DEVICES MUST NOT BE MODIFIED WITHOUT THE AUTHORISATION OR INDICATIONS OF THE MANUFACTURER DO NOT PULL DISCONNECT TWIST ELECTRIC CABLES LEAVING THE STOVE EVEN IF DISCONNECTED FROM THE ELECTRIC POWER SUPPLY MAINS ITIS ADVISED TO POSITION THE POWER SUPPLY CABLE SO THAT IT DOES NOT COME INTO CONTACT WITH HOT PARTS OF THE APPLIANCE THE POWER SUPPLY PLUG MUST BE ACCESSIBLE AFTER INSTALLATION DO NOT CLOSE OR REDUCE THE DIMENSIONS OF THE AIRING VENTS IN THE PLACE OF INSTALLATION THE AIRING VENTS ARE ESSENTIAL FOR CORRECT COMBUSTION DO NOT LEAVE THE PACKAGING ELEMENTS WITHIN REACH OF CHILDREN OR UNASSISTED DISABLED PERSONS THE HEARTH DOOR MUST ALWAYS BE CLOSED DURING NORMAL FUNCTIONING OF THE PRODUCT WHEN THE APPLIANCE IS FUNCTIONING AND HOT TO THE TOUCH ESPECIALLY ALL EXTERNAL SURFACES ATTENTION MUST BE PAID CHECK FOR THE PRESENCE OF ANY OBSTRUCTIONS BEFORE SWITCHING THE APPLIANCE ON FOLLOWING A PROLONGED PERIOD OF INACTIVITY THE GENERATOR HAS BEEN DESIGNED TO FUNCTION IN ANY CLIMATIC CONDITION IN PARTICULARLY ADVERSE CONDITIONS STRONG WIND FREEZING SAFETY SYSTEMS MAY INTERVENE THAT SWITCH THE GENERATOR OFF IF THIS OCCURS CONTACT THE TECHNICAL AFTER SALES SERVICE AND ALWAYS DISABLE THE SAFETY SYSTEMS IN THE EVENT THE FLUE CATCH
12. full cleaning including ignition plug pipe cleaning C BM Tank complete emptying and cleaning Air intake pipe check and cleaning of the flow sensor where necessary ENGLISH 27 OExtraflame DISPLAYS The start up phase is in progress PELLET FEEDING Continuous pellet feeding is in progress during the ignition phase The ignition phase is in progress The start up phase is in progress The normal work phase is in progress The stove is working at minimum BURN POT CLEANING Automatic burn pot cleaning is in progress FINAL CLEANING The final cleaning is in progress STAND BY Stove off waiting for re ignition due to an external thermostat n A new ignition is attempted when the stove has just been switched off When the stove switches off one STAND BY must wait for the complete shutdown of the fumes motor then clean the burn pot The stove can only be COOLING re ignited when these operations have been performed Stove off due to water temperature over set Stove off waiting for re ignition as all the requests have been satisfied STAND BY The stove is cooling after a power cut Once cooling is completed it will re start automatically BLACK OUT ANTI FREEZE The anti freeze function is in progress as the H20 t is below the factory set threshold the pump is active until the water reaches the pre set factory parameter 2 C ANTILOCK The pump antilock function is in progress only if the stove has been i
13. is to prevent unexpected power increases The flue fitting can be mounted between the boiler and the flue only after this inspection An inspection of the connections with pre existing flues is recommended ANTI CONDENSATION DEVICE MANDATORY Make sure a suitable anti condensate circuit has been realised which guarantees an appliance return temperature of at least 55 The automatic thermostatic valve for instance is used in solid fuel boilers as it prevents cold water from returning into the exchanger A high return temperature allows efficiency improvement reduces formation of smoke condensation and prolongs the generator s life span The manufacturer recommends using the 55 C model with 1 hydraulic connections Valve sold as an accessory optional ENGLISH 9 OExtraflame POSITIONING For correct product functioning it is recommended to position it so that it is perfectly level using a spirit level REARMS The figures below illustrate the positions of the tank 85 C and 20 100 C rearms Contact the qualified technician if one of the rearms should be triggered so as to verify the cause 85 C 100 C
14. the limits pellets also have technical advantages While wood has a calorific value of 4 4kWh kg with 15 humidity after around 18 months of seasoning the calorific value of pellets is 5 kWh kg Pellet density is 650kg m3 and the water content is equal to 8 of its weight For this reason they do not require seasoning in order to arrive at a sufficiently adequate degree of heat yield The pellets used must comply with the characteristics described by the following standards ENPLUS UNIEN 14961 2 UNI EN ISO 17225 2 class A1 or A2 The manufacturer always recommended using pellets with a diameter of 6 mm with its products PELLET STORAGE In order to ensure problem free combustion pellets must be stored in a dry place Open the tank lid and load the pellets using a scoop THE USE OF EXPIRED PELLETS OR ANY OTHER MATERIAL WILL AFFECT THE FUNCTIONALITY OF YOUR C GENERATOR AND MAY LEAD TO THE TERMINATION OF THE WARRANTY AND CESSATION OF ANY ACCOMPANYING RESPONSIBILITY ON THE PART OF THE MANUFACTURER CHECKS AND PRECAUTIONS FOR FIRST IGNITION IMPORTANT IN ORDER FOR THE GENERATOR TO WORK PROPERLY THE HYDRAULIC SYSTEM S PRESSURE MUST BE BETWEEN 0 6 AND 2 5 BAR If the pressure detected by the digital pressure switch is below 0 6 or above 2 5 bar it triggers a boiler alarm Bringing the water pressure within the standard values it is possible to reset the alarm by pressing the button ba for 3 seconds The alarm
15. ES FIRE USE SUITABLE SYSTEMS FOR SUFFOCATING THE FLAMES OR REQUEST HELP FROM THE FIRE BRIGADE THIS APPLIANCE MUST NOT BE USED TO BURN WASTE DONOTUSE ANY FLAMMABLE LIQUIDS FOR IGNITION DURING THE FILLING PHASE DO NOT PUT THE BAG OF PELLETS TO INTO CONTACT WITH THE PRODUCT THE MAJOLICAS ARE TOP QUALITY ARTISAN PRODUCTS AND AS SUCH CAN HAVE MICRO DOTS CRACKLES AND CHROMATIC IMPERFECTIONS THESE FEATURES HIGHLIGHT THEIR VALUABLE NATURE DUETO THEIR DIFFERENT DILATION COEFFICIENT THEY PRODUCE CRACKLING WHICH DEMONSTRATE THEIR EFFECTIVE AUTHENTICITY TO CLEAN THE MAJOLICAS IT IS RECOMMENDED TO USE A SOFT DRY CLOTH IF A DETERGENT OR LIQUID IS USED THE LATTER COULD PENETRATE INSIDE THE CRACKLES HIGHLIGHTING THEM ROUTINE MAINTENANCE Based on Decree 22 January 2008 n 37 art 2 routine maintenance means interventions aimed at reducing degradation due to normal use as well as dealing with accidental events entailing the need of first interventions which however do not modify the structure of the system upon which one is intervening or its intended use according to the requirements laid down by the technical standards in force and by the manufacturer s use and maintenance manual 8 ENGLISH OExtraflame HYDRAULIC SYSTEM Certain concepts referring to the Italian Standard UNI 10412 2 2009 are described in this chapter As previously described when installing all national regional provincial and council Standards in force provid
16. RAZIER ENSURES SUCCESSFUL OPERATION KEEPING THE BRAZIER AND ITS HOLES ALWAYS THOROUGHLY CLEAN FROM ANY RESIDUE FROM THE COMBUSTION GUARANTEES EXCELLENT FE COMBUSTION OFTHE GENERATOR OVERTIME AVOID ANY MALFUNCTIONS THAT MAY REQUIRE THE INTERVENTION OF THE TECHNICIAN IT IS POSSIBLE TO USE THE FUNCTION IN THE USER MENU ADJUSTMENT SET PELLET LOAD TO ADJUST COMBUSTION BASED ON THE DESCRIBED REQUIREMENTS BURN POT HOLES ENGLISH 25 OExtraflame ROUTINE MAINTENANCE PERFORMED BY QUALIFIED TECHNICIANS Routine maintenance must be performed at least once a year Since the generator uses pellets as its solid fuel it requires an annual routine maintenance operation which must be performed by a qualified technician using original spare parts only Failure to comply with the above can compromise the safety of the appliance and void the the guarantee conditions Complying with the cleaning intervals dedicated to the user described in the use and maintenance manual will guarantee the correct combustion by the generator over time avoiding any malfunctioning and or failures which could require further intervention by the technician Routine maintenance requests are not covered by the product guarantee DOOR GASKETS ASH DRAWER AND BURN POT Gaskets guarantee the hermetic seal of the stove and its ensuing correct operation They must therefore be checked regularly should they be worn or damaged replace them immediately This must be
17. ROBE H20 probe failure ALARM H20 PRESSURE The pressure of the water has exceeded the max threshold ENGLISH Check pellet feed see Pellet feed adjustment If the problem cannot be solved contact an authorised technician Check hermetic door closure Check hermetic closure of the ash drawer Check cleanliness of the fumes pipe of the sensor in the primary air channel and the combustion chamber Check for the presence of pellets in the feed box Adjust pellet flow see Pellet feed adjustment Check the procedures described in the Ignition chapter Take the stove to OFF conditions using key 1 and repeat the procedure described in the Ignition chapter Check for the presence of pellets in the feed box Adjust the pellet flow see Pellet feed adjustment Check hermetic door closure Check hermetic closure of the ash drawer Check cleanliness of the fumes pipe and the combustion chamber Contact after sales centre Possible air in the system vent the system Lack of adequate circulation Lack of or inadequate safety zone The water in the stove has exceeded 95 C Possible circulator anomaly If the problem persists the reset operations must be carried out by an authorised technician Check closure of the door Check that the burn pot is clear and clean The automatic burn pot cleaning is blocked If the problem persists contact the service centre Possible air in the syste
18. THE GENERATOR FREQUENCY IS APPROXIMATE THEY DEPEND ON THE QUALITY OF THE PELLETS USED AND THE FREQUENCY OF USE IT CAN HAPPEN THAT THESE OPERATIONS SHOULD BE PERFORMED MORE FREQUENTLY CLEANING AND MAINTENANCE BY THE USER Routine cleaning operations as specified in this use and maintenance manual must be performed with the utmost care according to the instructions procedures and frequency intervals described in this use and maintenance manual CLEANING THE SURFACES AND COVERING Never use abrasive or chemically aggressive detergents for cleaning The surface cleaning must take place when both the generator and the coating are completely cold For the maintenance of surfaces and metal parts simply use a damp cloth with water or mild soap and water Failure to observe the instructions may damage the surface of the generator and invalidate the warranty CLEANING THE CERAMIC GLASS Never use abrasive or chemically aggressive detergents for cleaning The cleaning of the ceramic glass is allowed only when the latter is completely cold To clean the ceramic glazing simply use a dry brush and some damp newspaper dabbed in the ash If the glazing is very dirty only use a specific ceramic glazing detergent Spray a modest amount onto a cloth and wipe the ceramic glazing Do not spray cleaner or any other liquid directly on the glass or on the gaskets Failure to observe the instructions may damage the surface of the ceramic glass and invalidate the
19. a system equipped with an operational earthing system Turn off the product in the event of a failure or malfunctioning Unburned pellets that build up in the burner following each failed start up must be removed before attempting to start up the product again Make sure that the burner is clean and correctly positioned before starting it up again Do not wash the product with water Water may penetrate into the unit and cause faults in the electrical insulation This can cause electric shocks Installations not complying with the regulations in force as well as incorrect use and failure to comply with the maintenance scheduled by the manufacturer will invalidate the guarantee 9 ENGLISH 31 uExtraf ame Riscaldamento a Pellet EXTRAFLAME S p A Dell Artigianato 12 36030 MONTECCHIO PRECALCINO VI ITALY EN 39 0445 865911 amp 39 0445 865912 info extraflame it EJ www lanordica extraflame com The Manufacturer reserves the right to vary the features and data shown in this booklet at any time and without prior notice in order to improve its products This manual cannot be considered as a contract for third parties 02 07 2015 004205259 MU CALDAIE HP 15 22 30 008
20. at 20 ENGLISH OExtraflame e ENABLE CHRONO It allows to enable disable the chrono and the various time slots of the boiler ENABLE CRONO CRONO ON PRG1 O0M PRG3 0N PRG 2 PRG e PELLET REGULATION PELLET ADJUST The following menu allows to adjust the percentage of pellet feed If the generator has operating problems due to the quantity of pellets 8 8 o you can adjust the pellet load directly from the control panel Problems related to fuel quantity can be divided into 2 categories EY the generator never manages develop adequate flame tending to remain very low even at high power at minimum power the generator tends to almost switch off taking the generator into NO PELLETS alarm when the generator displays the alarm for NO PELLETS there may be non burnt pellet inside he brazier FUEL SHORTAGE EXCESS FUEL the generator develops a very high flame even at low power the panoramic glass tends to get very dirty almost completely darkening it the burn pot tends to become encrusted blocking the holes for air intake due to the excessive pellet feed as it is only burned partially The adjustment to be performed is in percentage Therefore a modification of this parameter will lead to a proportional variation of all generatorfeeding speeds Feeding is from 3096 to 2090 STATUS References reserved to the technician USER MENU The USER MENU allows you
21. brazier facilitating the cleaning of the combustion chamber To activate the function 1 W With the generator cold and in OFF state press and subsequently for 5 sec With the ash hook supplied as standard scrape the walls of the combustion chamber and transfer the residual ash in the brazier room gt into the ash tray After cleaning press and hold the button OPEN THE DOOR ONLY WHEN THE OPERATION IS PERFORMED THE DISPLAY WILL INDICATE THE SUCCESSFUL OPENING ENGLISH 23 OExtraflame CLEANING AND MAINTENANCE ALWAYS FOLLOW THE INSTRUCTIONS IN MAXIMUM SAFETY CONDITIONS Make sue the power cable is unplugged since the generator could be programmed to start That the generator is cold in its entirety The ashes are completely cold Ensure an effective exchange of air in the room during the cleaning of the product A poor cleaning is detrimental to the proper functioning and safety 9 9 MAINTENANCE For correct operation the generator must undergo routine maintenance by a qualified technician at least once a year The routine checks and maintenance operations must always be performed by qualified trained technicians in accordance with the applicable regulations in force and with the instructions provided in this use and maintenance manual EVERY YEAR MAKE THE EXHAUST FUMES SMOKE DUCTS AND T FITTINGS INCLUDING CAPS AND INSPECTION DOORS BE CLEANED IF ANY CURVES AND ANY HORIZONTAL SECTIONS C THE CLEANING OF
22. can be reset only if the fumes motor has stopped and 15 minutes have elapsed from the display of the alarm THE PELLET LOADING MOTOR DOES NOT WORK Due to the filling of the system it is normal that there is air inside the circuit During the 1st ignition cycle water movement causes the displacement of air bubbles and their out flow from the automatic vents out of the system This can cause the pressure to drop and activate the minimum pressure switch which stops the motor that transports the pellets and therefore the heat generator Vent out the system if necessary even multiple times to remove the air and reload it if the pressure is too low Itis not a malfunction but a normal occurrence due to its filling After filling the plumber must always thoroughly vent the system using the special vents in the circuit and running the air breather function on the machine After the first ignition and with a cold machine re activate the function air breather see chapter OTHER FUNCTIONS BULB THERMOSTATS RESET Check by pressing the reset buttons 85 100 C located on the back of the appliance before contacting a technician see section RESET ENGLISH 13 OExtraflame TOUCH SCREEN DISPLAY The boiler is equipped with a modern touch screen display that allows the adjustment of the individual device functions in an easy and intuitive way to the user All adjustments and settings depicted in the screens can be performed dire
23. ctly via the integrated touch screen display Tapping the buttons icons on the display surface the different actions are activated The surface of the touch screen display reacts with the touch of a finger WARNING Do not use protective films this may cause the malfunction of the display Do not put the touch screen to direct or indirect contact with the water The touch screen display may malfunction in humid conditions or when exposed to water To avoid damaging the touch screen display it should not be touched with sharp objects and too much pressure must be exerted with your fingers ecoe 009090 XX 1 RR XC TOUCH SENSITIVE PART THE MANUFACTURER HAS AN ADDITIONAL CARD OPTION THAT ALLOWS THE BOILER THE FOLLOWING ADDITIONAL FUNCTIONS IN SYSTEM MANAGEMENT THE TABLE BELOW SHOWS THE VARIOUS POSSIBILITIES WHICH THE OPTIONAL CAN OFFER Management of domestic water accumulation Puffer management NM 3 heating areas 5 Option of instant domestic water Management puffer pump or 4th heating area NE Anti Legionnaires disease management for domestic water accumulation T inaatasan jaanje S Chrono domestic water management accumulation Auxiliary output management and control 14 ENGLISH OExtraflame CONTROL PANEL AND ICONS ICON MEANING Indicates the prese
24. d on the rear of the machine one is red and the other one is black STBY clamp HP30 15 22 In case you are using the manufacturer s Power Line Communication devices a qualified technician must perform the connection directly the board For more information contact your local dealer ENGLISH 19 OExtraflame SET POWER The following menu allows to set the power Minimum power 1 maximum power 5 MENU POWER SET SET USER REGULATION SET SET TEMPERATURE The following menu allows the boiler temperature to be set Possible setting are 65 80 C MENU POWER SET EMPERATURE SET USER REGULATION USER REGULATION MENU The USER REGULATION allows you to POWER SET Adjust the frequency of the BURNING POT CLEANING fec Enable disable the STAND BY Enable disable the CHRONO Adjust the PELLET in percentage e BURN POT CLEANING POT CLEANING L The menu allows to increase the frequency of the automatic cleaning Gy of the brazier Range 0 50 STAND BY STAND BY The Stby function is used if immediate generator switch off or modulation via an additional thermost
25. display 22 ENGLISH SE Nim LANGUAGE OExtraflame BUZZER When set to OFF the acoustic signal is disabled BRIGHTNESS It allows you to adjust the backlight of the display DISPLAY The possible settings range from OFF 10 to 30 OFF Activating OFF the back light of the display will go off after a BRIGHTNESS 15 preset delay The back light will go on as soon as a key is pressed or if an CONTRAST 16 alarm should be triggered in the machine OM ESE CONTRAST Allows you to change the display contrast Range from 2 50 e RESET LANGUAGE Allows to reset all values modifiable by the user to the default DISPLAY values RESET n OTHER FUNCTIONS AIR DISCHARGE This function allows to bleed any air in the thermal product For 15 minutes the pump operates alternately 30 seconds on and 30 seconds off To activate the function With the generator cold and in OFF state press and then AIR for 5 secs To stop the air Bleeding function press the button FIRST LOAD This function allows to activate the pellet feeding motor reducer for continuous functioning OFF ye To activate the function 1 6 MER 14 55 STBY OFF With the generator cold and in OFF state press and then LOAD T 2 L 5 5 for 5 secs Y Gy ef R CLEANING 5 To stop the First load press the key Y FIRST LOAD AIR DISCHARGE COMBUSTION CHAMBER CLEANING This feature allows you to open the bottom
26. e for more than two seconds to turn on the generator 15 minutes are available for the ignition phase After ignition and having reached the control temperature the generator stops the ignition phase and passes to STARTING STARTING During the start up phase the generator stabilises combustion increasing it progressively then switching to WORK mode WORK During the work phase the generator reaches the set power see following item ADJUSTMENT SET POWER Set the operating power from 1 to 5 Power 1 minimum level Power 5 maximum level ADJUSTMENT SET TEMPERATURE H20 Set the boiler temperature between 65 80 C PUMP OPERATION The pump activates water circulation when the in the generator the t of the water reaches 60 C As the pump always functions above 60 an always open heating area is recommended to make product functioning increasingly uniform preventing overheating blocks Normally this area is defined Safety zone BURNING POT CLEANING At pre set intervals the generator performs the brazier cleaning switching the machine off When the cleaning phase is finished the generator will re start automatically and continue its work back to the power level selected MODULATION and H OFF As the water temperature approaches the set point the boiler starts to modulate automatically bringing itself to the minimum power If the temperature increases beyond the set point it will automatically switch off indicating H OFF a
27. e more than 4 direction changes including the one due to the use of the T element fitting with a condensation collection cap must be provided at the base of the vertical section If the exhaust is not inserted in an existing flue a vertical section with a windproof end piece is required UNI 10683 The vertical duct can be inside or outside the building If the smoke duct is inserted in an existing flue it must be certified for solid fuel If the smoke duct is outside the building it must always be insulated The smoke ducts must have at least one airtight inlet for flue gas sampling All the sections of the flue gas duct must be accessible to inspection Inspection openings must be provided for cleaning 9 9 CHIMNEY CAP The chimney caps must meet the following requirements they must have a useful outlet section no less than double that of the chimney ducted system on which it is installed they must be adapted in order to prevent the penetration of rain and snow in the chimney ducted system they must be built so that in the event of winds coming from all directions and from any angle the expulsion of combustion products is in any case ensured EXAMPLES OF CORRECT CONNECTION TO THE CHIMNEY Protection from rain and wind Protection from rain and wind Insulated flue J Q 40 405 02020502
28. e of installation The airing vents are indispensable for correct combustion 6 ENGLISH 9 9 9 OExtraflame Do not leave the packaging elements within reach of children or unassisted disabled persons The hearth door must always be closed during normal functioning of the product Avoid direct contact with parts of the appliance that tend to heat up during functioning Check for the presence of any obstructions before switching the appliance on following a prolonged standstill period The generator has been designed to function in any climatic condition In particularly adverse conditions strong wind freezing safety systems may intervene to switch the generator off If this occurs contact the technical after sales service and always disable the safety system Ifthe flue should catch fire be equipped with suitable systems for suffocating the flames or request help from the fire service generator should block indicated by a signal on the display and that is not relative to lack of routine maintenance contact the technical after sales centre 9 9 9 THESE BOILERS MUST BE USED TO HEAT WATER TO A TEMPERATURE THAT DOES NOT EXCEED BOILING POINT IN THE CONDITIONS OF INSTALLATION RECOMMENDED DISTANCES FOR THE BOILER COMPARTMENT Below are a few images relative to the minimum distances required in the boiler room The company recommends the following measurements to be complied with
29. ed by the country in which the appliance has been installed must be complied with During installation of the generator it is MANDATORY to adjust the system with a manometer in order to display the water pressure TABLE OF THE DEVICES FOR CLOSED VESSEL SYSTEMS PRESENT AND NOT PRESENT IN THE PRODUCT Safety valve RM Pump control thermostat it is controlled by the water probe and the board program Acoustic alarm activation thermostat Water temperature indicator display NIS Pressure transducer with view on the display Acoustic alarm 5 Automatic adjustment circuit breaker switch managed by board program Pressure transducer with minimum and maximum pressure switch alarm Water overheating automatic circuit breaker switch block thermostat Circulation system pump S Expansion system INSTALLATION AND SAFETY DEVICES The installation relative system connections commissioning and inspection of correct functioning must be carried out with the highest professional standards in full compliance with the national regional and council Standards in force as well as these instructions For Italy installation must be carried out by professionally authorised staff Ministerial Decree dated 22 01 08 n 37 The Manufacturer declines all liability for damage injury to objects persons caused by the plant TYPE OF SYSTEM There are 2 different types of system Open vesse
30. h a receipt stating that the documentation has been provided and must keep it with a copy of the technical documentation relating to the installation For installation in a condominium prior approval from the condominium s administrator must be requested COMPATIBILITY Installation in premises with fire hazards is forbidden Installation in residential premises except for sealed operation appliances is also forbidden in which there are liquid fuel operated appliances with continuous or intermittent operation which draw the combustion air in the room in which they are installed or in which there are type B gas appliances intended for room heating with or without production of domestic hot water and in adjacent and adjoining premises or in which in any case the depression measured during installation between the internal and external environment is greater than 4 INSTALLATIONS IN BATHROOMS BEDROOMS AND STUDIO FLATS Installation in bathrooms bedrooms and studio flats is only allowed for sealed or closed hearth appliances with ducted combustion air taken from the outside POSITIONING AND SAFETY DISTANCES The support surfaces and or points must have a suitable capacity to bear the overall weight of the appliance accessories and coverings If the floor is made of a combustible material we recommending using a non combustible material to protect the front part from any burnt material which might fall during routine cleaning
31. han 2 seconds to exit the menu Briefly pressing you can go back to a step Allows you to scroll through the menus Allows access to additional info OM OFF Allows to enable ON or disable OFF Allows access to the user menu MENU STRUCTURE 9 SET POWER wy SET POWER Y icy SET TEMPERATURE icy SET H20 USER REGULATION 97 BURN POT CLEANING 4 Y e STATUS 8 STATUS 1 2 4 STAND BY ENABLE CHRONO Y PELLET R USER MENU SET CLOCK y C4 SET CHRONO Y LANGUAGE Y DISPLAY TECHNIC SET KEYS LOCKED BRIGHTNESS lt RESERVED TO THE TECHNICIAN BASIC INSTRUCTIONS The following recommendations must be followed the first times the generator is ignited It is possible that slight odours are produced due to the drying of the paints and silicones used Do not remain in the environment for long periods Do not touch the surfaces as they could still be unstable Air the room well several times The hardening of the surfaces is terminated after several heating processes This appliance must not be used to burn waste 16 pa It allows to go back a step if pressed briefly if held longer allows to exit until the main scream Before igniting the generator the following points must be verified The
32. he malfunction is linked to external events and or conditions such as including but not limited to insufficient capacity of the systems wrong installation and or maintenance by the personnel which hasn t got the skills prescribed by the laws of the country of residence of the consumer negligence inability to use the product and wrong maintenance by the consumer with respect to what is reported and recommended by the instructions manual of the product which is part of the sales contract this guarantee will be void Damage to the product that cannot be related to manufacturing defects are also not included in this guarantee Similarly are excluded defects related to incorrect operation of the flue according to the legislation in force in the country at the moment of purchase Other exclusions include all product defects due to carelessness accidental breakdown tampering and or damage during transport scratches dents etc interventions carried out by unauthorised personnel and further damage caused by incorrect interventions by the consumer trying to arrange the initial malfunction The following consumables are excluded by the guarantee gaskets ceramic or tempered glasses cast iron grilles or coatings refractory materials e g Nordiker or others painted chrome plated or golden parts majolica ware handles the brazier and its related components For Idro products the heat exchanger is not covered by the guarantee if a suitable condensation
33. hydraulic system must be completed in compliance with the guidelines of the regulations and the manual The tank must be full of pellets The combustion chamber must be clean The burn pot must be completely free and clean Check the hermetic closure of the fire door and the ash drawer Check that the power supply cable is connected correctly The bipolar switch in the rear right part must be positioned on 1 6 ENGLISH OExtraflame COMMISSIONING SETTINGS Once the power cable at the back of the generator has been connected move the switch located on the back to position 1 The switch at the back of the generator powers the generator board The generator stays off and the panel shows an initial screen with the word OFF MAINS FREQUENCY 50 60HZ In the event the generator is installed in a country with 60Hz frequency the generator will display wrong mains frequency Change in the frequency to 60Hz SET CLOCK Setting the clock allows to adjust the time and date SET CLOCK DAY TUESDAY 14 SET CHRONO TIME LANGUAGE MINUTES 55 lt sm mt SET LANGUAGE It enables the user to select one of the available languages Italian English French German Spanish LANGUAGE SET CLOCK SET CH ITALIANO ESE ENGLISH 17 OExtraflame OPERATION AND LOGICS IGNITION Once you have checked the basic instructions listed above press th
34. l system and closed vessel system The product has been designed and made to work with closed vessel systems CHECK THAT THE PRELOAD OF THE EXPANSION VESSEL IS SET TO 1 5 BAR SAFETY DEVICES FOR CLOSED VESSEL SYSTEM According to Standard UNI 10412 2 2009 in force in Italy closed systems must be equipped with safety valve pump control thermostat acoustic alarm activation thermostat temperature indicator pressure indicator acoustic alarm regulation automatic circuit breaker switch automatic circuit breaker block switch block thermostat circulation system expansion system safety dissipation system incorporated with the generator with thermal safety valve self activated whenever the appliance does not have a temperature self adjustment system DISTANCES OF SAFETY DEVICES ACCORDING TO THE STANDARD The temperature safety sensors must be in place on the machine at a distance no greater than 30 cm from the flow connection Whenever the generators lack a device those missing can be installed on the generator flow pipe within a distance no greater than 1 m from the machine COMMISSIONING CHECKS Before connecting the boiler a wash all system piping thoroughly in order to remove any residues which might compromise the correct functioning of certain system components pumps valves etc b check to verify that the flue has adequate draught that it is not narrowed and that other appliances do not discharge into the flue This
35. m vent the system Possible lack of water or leaks due to anomalies in some system component If the problem persists contact the service centre Contact after sales centre Possible air in the system vent the system Check that the expansion vessels are not damaged or under dimensioned Check that the cold system is loaded at the correct pressure If the problem persists contact the service centre 29 OExtraflame GUARANTEE TERMS 1 Extraflame S p A products are guaranteed within the European community for 24 months from the date of purchase Purchase has to be proved by means of a valid fiscal document issued by the seller receipt invoice or shipment document identifying the purchased product and its purchase and or delivery date WARNING This conventional guarantee does not replace the guarantee regulated by the European legislation on consumer rights The conventional guarantee is only applicable to the Italian region and to those areas within the European Community where the Authorised Technical Assistance Centres are active see the www lanordica extraflame com website It is also limited to the state of residence of the consumer which must coincide with the premises and or registered office of the seller of the Extraflame S p A product These regulations do not apply if the product is purchased within commercial entrepreneurial or professional circumstances In these cases the product guarantee will be limited t
36. missioning the product verify that all safety and control devices the generator consists of work properly All electrical components that make up the generator must be replaced with original spare parts exclusively by an authorised technical assistance centre thereby guaranteeing correct operation Before leaving the system the staff in charge of commissioning must monitor the operation of the generator for at least one complete work cycle The geneerator must be serviced at least once a year programming it in advance with the technical assistance centre STANDARDS The boilers have been designed and realised in compliance with the following Directives UNI EN 303 5 Boilers for central heating Boilers for solid fuel with manual and automatic feeding with a nominal heat output of up to 500 kW DIRECTIVES 2004 108 EMC directive 2006 95 Low voltage directive 2006 42 EC Machinery directive 2011 65 EU RoHS 2 directive FOR SAFETY It is forbidden for the generator to be used by children or unassisted disabled persons Do not touch the generator when you are barefoot or when parts of the body are wet or humid The safety and adjustment devices must not be modified without the authorisation or indications of the manufacturer Do not pull disconnect twist electric cables leaving the gnerator even if disconnected from the electric power supply mains Do not close or reduce the dimensions of the airing vents in the plac
37. n an OFF state for at least 96 hours the pump is activated for the time pre set by the manufacturer in order to prevent it from blocking AUTO BLOW The automatic blow is active 28 ENGLISH OExtraflame ALARMS DISPLAY EXPLANATION SOLUTION ES On indicates the presence of an alarm Flashing indicates the deactivation of the depression sensor The alarm can be reset by pressing key 1 for 3 seconds only if the fumes motor has stopped and if 15 minutes have elapsed from when the alarm was displayed The door is not closed correctly The ash drawer is not closed correctly CLEAN CHECK UP 1 2 1 IN START UP STAGE 2 IN OPERATING STAGE NO IGNITION The combustion chamber is dirty The flue exhaust pipe is blocked The pellet feed box is empty Pellet feed calibration inadequate NO IGNITION No current during the ignition phase BLACK OUT The pellet feed box is empty NO PELLETS No pellet feed The motor reducer does not feed pellets The door is not closed correctly The ash drawer is not closed correctly DEPR ALARM The combustion chamber is dirty The flue exhaust pipe is blocked DEBIMETER Flow sensor faulty Sensor disconnected FAULT Air in the system H20 OVERTEMP Unsuitable circulation Door not closed properly Burn pot dirty or clogged TRAPDOOR FAULTY ALARM MINIMUM PRESSURE The system pressure read by the pressure switch is too low ALARM H20 P
38. nce of an alarm The machine will turn off e This indicates the system pressure detected by the machine e It indicates the pump operation Off pump OFF ON pump on Flashing ling the safety device is active H2O temperature gt 85 C e Indicates the contact of the external additional thermostat Contact closed the contact of the additional external thermostat is closed Contact open the contact of the additional external thermostat is open Indicates the operating status of the machine with manual operation or weekly programming 11111 ds 62 Hand icon the weekly programming function is off manual management Chrono icon activates the weekly programming function DISPLAYING THE VARIOUS TEXT MESSAGES A WORK ACTUAL POWER 77 85 LL MONDAY 05 11 2013 TEMPERATURE H20 BOILER 6 Y DAY DATE TIME YEAR By briefly pressing appear additional information such as ite E amp CHRONO ACTIVE OR MANUAL MODE NNNM STATUS OF THE CONTACT EXTERNAL DETECTED PRESSURE IN THE la MER 14 55 STEY gt STAND BY FUNCTION BOILER ENGLISH 15 OExtraflame KEY FUNCTIONS KEY FUNCTION KEY FUNCTION Press and hold for more than 2 seconds to Allows increases select or decrease turn on or turn off the boiler a mode SET Press and hold for more t
39. nd to those envisioned by the law Installation must be carried out by authorised staff who must provide the buyer with a declaration of conformity for the system and will assume full responsibility for final installation and as a consequence the correct functioning of the installed product It is necessary to bear in mind all laws and national regional provincial and town council Standards present in the country the appliance has been installed The Manufacturer cannot be held responsible for the failure to comply with such precautions It is recommended to wash all the pipes of the system well before installation to remove any residue that could compromise the correct operation of the appliance During installation inform the user regarding a If water leaks he must close the water supply and promptly inform the after sales technical service b The system working pressure must be checked periodically If the generator is not used for a long period of time it is recommended to contact the after sales technical service to carry out at least the following operations Set the master switch to position O Close the water taps of both the heating system and the domestic hot water system Empty the heating system and the domestic hot water system if there is risk of freezing COMMISSIONING After removing the packaging ensure that the content is intact and complete Otherwise contact the dealer where the appliance was purchased When com
40. nd will automatically go back on when the temperature drops below the set point SWITCH OFF Press key 1 for three seconds When the operation has been performed the appliance automatically enters the switch off phase blocking the supply of pellets The flue gas exhaust motor will remain on until the generator temperature has dropped below the factory parameters RE IGNITION The genertor can be re ignited both automatically or manually when the cooling cycle conditions and the preset timer have been satisfied DO NOT USE ANY INFLAMMABLE LIQUIDS FOR IGNITION C DO NOT ALLOW THE BAG OF PELLETS TO COME INTO CONTACT WITH THE HOT GENERATOR IN THE EVENT OF CONTINUOUS NO IGNITION CONTACT AN AUTHORISED TECHNICIAN 18 ENGLISH OExtraflame STBY ADDITIONAL ROOM THERMOSTAT PLEASE NOTE Installation must be performed by an authorised technician Is it possible to thermostat a room adjacent to the room where it was placed the generator just connecting a room thermostat according to the procedure described in the next step it is advisable to position the optional mechanical thermostat at a height of 1 50 m from the floor The generator functioning with the external thermostat connected to the STBY terminal can be different on the basis of the activation or disabling of the STBY function The STBY clamp leaves the factory jumpered therefore it is always with closed contact on request ADDITIONAL ROOM THERMOSTAT FUNCTIONING WITH STBY
41. o a period of 12 months from the date of purchase ITALIAN GUARANTEE What must be done if there is a product malfunction Consult the instructions manual to make sure the malfunction cannot be solved by using the product correctly Make sure the malfunction is included in those covered by the guarantee otherwise the cost of the intervention will be borne entirely by the consumer When requesting the intervention of the Assistance service at the Authorised Assistance Centre always specify type of malfunction model of the appliance complete address phone number EUROPEAN GUARANTEE What must be done if there is a product malfunction Consult the instructions manual to make sure the malfunction cannot be solved by using the product correctly Make sure the malfunction is included in those covered by the guarantee otherwise the cost of the intervention will be borne entirely by the consumer Request the intervention of the Assistance service or the address of the Authorised Technical Assistance Centre to the seller always specify type of malfunction model of the appliance complete address and phone number If the malfunction arises in the first 6 months of the product s life the consumer has the right to have the product repaired with no expense From the seventh to the twenty fourth month if a malfunction arises the consumer will bear the cost of the call while the seller will pay for the manpower and for any spare parts used 2 If t
42. operations The generator must be level to function properly The adjacent side and rear walls and the supporting surface must be made of non combustible material Installation adjacent to combustible or heat sensitive materials is allowed as long as there is a suitable safety distance in between which for pellet stoves is REFERENCES INFLAMMABLE OBJECTS NON INFLAMMABLE OBJECTS Air inlet floor protection INSTALLING INSERTS When installing inserts access must be prevented to the internal parts of the appliance and it must not be possible to access live parts during extraction operations Any wiring for example the power cable or room probe must be positioned so as not to be damaged during movement of the insert and must not come into contact with hot parts VENTILATION AND AERATION OF THE INSTALLATION PREMISES Ventilation is deemed sufficient when the room is equipped with air inlets according to the table Percentage of the Appliance categories Reference standard net opening section with respect to the appliance fumes outlet section Minimum net opening value of the ventilation duct UNIEN 14785 UNI EN 303 5 In any case ventilation is deemed sufficient when the pressure difference between the external and internal environment is equal to or less than 4 Pa ENGLISH 11 OExtraflame In the presence of type B gas appliances with intermittent operation not intended for heating they m
43. performed by a qualified technician CONNECTION TO THE CHIMNEY Suction and clean the flue duct leading to the chimney once a year or whenever necessary If the installation entails horizontal flue duct sections suction all residue before it obstructs the passage of fumes DECOMMISSIONING END OF SEASON At the end of every season before you turn the stove off it is advisable to empty the pellet tank completely suctioning any pellet residue and dust from the inside In addition disconnect the generator from the electricity supply and for increased safety particularly if children are present remove the power supply cable Routine maintenance must be performed at least once a year C IF THE POWER SUPPLY CABLE IS DAMAGED IT MUST BE REPLACED BY TECHNICAL SERVICE STAFF OR IN ANY CASE BY A SIMILARLY QUALIFIED TECHNICIAN SO AS TO AVOID ALL RISKS 26 ENGLISH OExtraflame ROUTINE MAINTENANCE THE PICTURES ARE PURELY INDICATIVE LA Fumes motor disassembly and cleaning and flue duct and T new silicone in the dedicated points NE Inspection of gaskets ash drawer and door replace and apply silicone where envisaged Combustion chamber door air slots and heat exchanger
44. power Flue gas temperature at rated power 29 103 136 122 0 0055 0 0065 0 0081 Flue gas reduced power kg s kg s 0 0128 0 0164 0 0194 Flue gas rated power Class of the boiler Combustion period Water supply control valve 65 80 65 80 65 80 Minimum return water temperature oO lt V O V O Efficiency at rated power 91 4 Noise O O O Value measured in an anechoic chamber with a device operating at rated power ENGLISH OUExtraflame WATER SIDE WATER FLOW RESISTANCE kg h Pa T t ndin 10K E 40 emperature jump corresponding N 2K 66 24214 WATER SIDE WATER FLOW RESISTANCE kg h Pa T rature jump correspondin EROS 2 emperature jump corresponding 20 99 J 9 WATER SIDE WATER FLOW RESISTANCE kg h Pa AT 10K 2668 SUBE ch AT 20K 1334 IDENTIFICATION OF COMPONENTS A Display B Pellet tank cover Door Power socket for electric cable E Safety thermostat manual reset 100 C Safety thermostat manual reset 85 G Combustion flue pipe O H Air intake tube for combustion Main power switch Serial port A IR e o o o o o o e 5 o o o o o ths o o o m o o o z o
45. proof circuit is not set up to ensure a return temperature of the device of at least 55 The guarantee excludes all the external components on which the consumer can directly operate during use and or maintenance or that can be subject to wear and or rust and stains on steel due to aggressive detergents If malfunctions are signalled which are not later confirmed during check by an authorised technician the cost of the intervention will be borne entirely by the consumer 3 If itis not possible to restore product conformity by repairing it the product component will be replaced the guarantee expiration date and conditions will remain the same established when the product component to be replaced has been purchased 4 Extraflame S p A cannot be held liable for injury or damage which may either directly or indirectly be caused to persons animals and property ensuing from failure to observe all the instructions provided in the relevant instruction manual and the warnings regarding installation use and maintenance of the product that can also be downloaded on the website 5 Interventions for adjusting and or regulating the product for the type of fuel or other reasons are excluded by the guarantee 6 If the product is repaired in one of the Authorised Technical Assistance Centres indicated by Extraflame S p A and if the product is replaced transport will be free of charge If the technician can repair the product at the user s place of re
46. sidence and they refuse transport to the workshop and redelivery will be paid by the consumer 30 ENGLISH OExtraflame 7 After the 24 months of the guarantee have elapsed any repair intervention cost will be completely borne by the consumer 8 In the case of disputes the only competent court is that of the Extraflame S p A registered office Vicenza Italy ADDITIONAL WARNINGS Only use the fuel recommended by the manufacturer The product must not be used as an incinerator use the product as a ladder or supporting structure Do not place laundry on the product to dry it Any clothes horse or similar objects must be kept at due distance from the product Danger of fire or damage to the coating The user is fully liable for any incorrect use of the product The manufacturer bears no civil or criminal liability for incorrect use Unauthorised tampering of any nature or replacement of spare parts of the product with non original parts may endanger the operator and the manufacturer bears no civil or criminal liability for this Large parts of the surface of the product can get very hot door handle glass smoke outlet pipes etc Please therefore avoid coming into contact with these parts without wearing suitable protective clothing or using appropriate measures such as heat protective gloves DO NOT use the product with the door open or if the glass is broken The product must be electrically connected to
47. to MENU USER REGULATION Set date and time See chapter before ignition Set the programming CHRONO Set the LANGUAGE Jer Efe 9 9 Set the DISPLAY Use the RESET SET ESC ENGLISH 21 OExtraflame e CHRONO The chrono allows to program 4 time spans within a day to use every day of the week The switch on and switch off time can be set in every time slot along with the days of use of the programmed time slot and the desired water temperature 65 80 C TO ENABLE THE CHRNONO FOLLOW THE INSTRUCTIONS DESCRIBED IN ENABLE CHRONO CHAPTER Shutdown hours lt lt Setting RECOMMENDATIONS EXAMPLE SET CHRONO CHRONO 2 CHRONO 3 t Days enabled Days not enabled 1 Monday 2 Sunday The ignition and switch off times must be within the arc of one day from 0 to 24 and not over several days Before using the chrono function set the current day and time Therefore check that the points listed in the Set clock sub chapter have been followed so that the chrono function works As well as programming it activate it as well Switch on time 07 00 Switch off time 18 00 CORRECT Switch on time 22 00 INCORRECT Switch off time 05 00 e LANGUAGE See chapter before ignition e DISPLAY Buzzer Brightness Contrast The Display menu allows you to Enable disable the buzzer Adjust the brightness of the display Adjust the contrast of the
48. to another place If it is damaged or lost request another copy from the area technician This product is intended for the use for which it has been expressly designed The manufacturer is exempt from any liability contractual and extracontractual for injury damage caused to persons animals and objects due to installation adjustment and maintenance errors and improper use Installation must be performed by qualified staff which assumes complete responsibility for the definitive installation and consequent good functioning of the product installed One must also bear in mind all laws and national regional provincial and town council Standards present in the country in which the appliance has been installed as well as the instructions contained in this manual The Manufacturer cannot be held responsible for the failure to comply with such precautions After removing the packaging ensure that the content is intact and complete Otherwise contact the dealer where the appliance was purchased All electric components that make up the product must be replaced with original spare parts exclusively by an authorised after sales centre thus guaranteeing correct functioning SAFETY THE GENERATOR MUST NOT BE USED BY PERSONS INCLUDING CHILDREN WITH REDUCED PHYSICAL SENSORY AND MENTAL CAPACITIES OR WHO ARE UNSKILLED PERSONS UNLESS THEY ARE SUPERVISED AND TRAINED REGARDING USE OF THE APPLIANCE BY A PERSON RESPONSIBLE FOR THEIR SAFETY CHILDREN MUST
49. ust have their own aeration and or ventilation opening The air inlets must meet the following requirements they must be protected with grids metal mesh etc but without reducing the net useful section they must be made so as to make the maintenance operations possible positioned so that they cannot be obstructed The clean and non contaminated air flow can also be obtained from a room adjacent to that of installation indirect aeration and ventilation as long as the flow takes place freely through permanent openings communicating with the outside The adjacent room cannot be used as a garage or to store combustible material or for any other activity with a fire hazard bathroom bedroom or common room of the building FLUE GAS EXHAUST The heat generator works in depression and is equipped with an outlet fan for flue gas extraction There must be a single exhaust system for the generator Using a flue that is shared with other devices is not allowed The components of the flue gas exhaust system must be chosen in relation to the type of appliance to be installed in compliance with UNI TS 11278 in the event of metal chimneys with particular attention to that stated in the specification UNI EN 13063 1 and UNI EN 13063 2 UNI EN 1457 UNI EN 1806 in the event of non metallic chimneys The length of the horizontal section must be minimal and in any case no longer than 3 metres with a minimum upward slope of 3 There must not b
50. warranty CLEANING THE TANK PELLETS When the tank empties completely unplug the power cord from the generator and remove residues dust chips etc from the tank empty before filling it DAILY BRAZIER Through a mechanical system the burn pot is cleaned at set intervals automatically by the boiler In the picture below one can see the burn pot with the opening underneath it Itisin any case recommended to remove any ash residue using a vacuum cleaner at least once every 2 days 24 ENGLISH OExtraflame DAILY SCRAPERS HP15 22 The heat exchangers must only be cleaned when the generator is cold Cleaning the heat exchangers allows to ensure constant heat output over time This type of maintenance must be performed at least once a day To do this just use the relevant scrapers positioned in the upper part of the generator making the upward movements and vice versa several times HP30 The cleaning of the heat exchangers is carried out automatically using a mechanical system that allows to guarantee over time constant heat output WEEKLY COMBUSTION CHAMBER AND THE ASH TRAY It is recommended to remove the ash in the combustion chamber at least once a week using a suitable vacuum cleaner To facilitate cleaning we recommend the activation of the CLEAN COMBUSTION CHAMBER See chapter c OTHER FUNCTIONS Weekly or when necessary empty the ashes from the drawer clean the holes inside the door A CLEAN B
Download Pdf Manuals
Related Search