User Manual
Contents
1. and password subscribed from your ISP supplier 3 DNS PRIMARY DNS SECONDARY DNS Key in the IP address of the domain name server obtained from your ISP Internet Service Provider 4 PORT The valid number ranges from 1 to 9999 The default value is 80 Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security See the example below PPPOE NETWORK TYPE PPPOE USER NAME EMPTY PASSWORD EMPTY IP 000 GATEWAY 000 NETMASK 000 PRIMARY DNS 001 PORT 000 000 000 001 SECONDARY DNS 055 244 0080 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT BACK gt NEXT lt lt ENTER ADVANCED OPERATION Note The PPPOE function needs to have one username and one password subscribed from one ISP Supplier and a DDNS account to correspond the dynamic IP address to a specific Hostname 4 6 3 DHCP 1 NETWORK TYPE Select the network type as DHCP 2 DNS PRIMARY DNS SECONDARY DNS Key in the IP address of the domain name server obtained from your ISP Internet Service Provider 3 PORT The valid number ranges from 1 to 9999 The default value is 80 Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security see the example below NETWORK TYPE DHCP IP 000 000 GATEWAY 000 0002. The cameras must be connected and power supplied BEFORE the DVR is powered on The DVR will automatically detect the video system of the connected camera s NTSC PAL and switch itself to the correct system 1 Video cable connection Connect the camera video output to the DVR video input port with a coaxial cable or RCA line with BNC connector 2 Audio cable connection For cameras which supports audio recording only Connect the camera audio output to the DVR audio input port with a coaxial cable or RCA line with BNC connector 3 Power connection Connect the camera with indicated power supply and make sure it s power supplied 2 3 Power Setup This device should be operated only with the type of power source indicated on the manufacturer s label Connect the indicated AC power cord to the power adapter and plug into an electrical outlet The power LED will be on Note Before the DVR is powered on make sure the cameras are connected and power supplied for the detection of the camera video system to be correct Note To ensure that your DVR works constantly and properly it s recommended to use an UPS Uninterruptible Power Supply for continuously operation Optional 2 4 Date and Time Setting Before operating your DVR please set the date and time on your DVR FIRST Note Please DO NOT change the date or time of your DVR after the recording function is activated Otherwise the recorded data will be disordered and
3. Confirm the camera is power supplied Check the setting of the camera lens Check the monitor s video cable and connection Check the camera s video cable and connection No recorded video Check if the HDD is installed and connected properly Check if MANUAL RECORD ENABLE option is set to ON and the record function in the CAMERA menu is set to ON too Timer recording is not working Check if TIMER RECORD ENABLE option is set to ON and the timer schedule has been arranged Motion detection recording is not working Check if EVENT RECORD ENABLE option is set to ON Check if the detection function DET is set to ON Check if the detection area AREA has been set Can t play the recorded data on my DVR There must be at least 8192 images of recorded data for playback to work properly If not your DVR will stop the playback For example if the IPS is set to 30 the recording time should be at least 2 3 seconds 8192 images 30 IPS for the playback to work properly Can t backup the video with audio Make sure your DVR support the audio function Make sure your camera supports the audio function Make sure your camera is connected to DVR VIDEO IN 1 and AUDIO IN Can t view the DVR images over the network with Check the DVR firmware version IE web browser after login Choose to allow the web browser ActiveX or applet in t
4. DATE MANUAL RECORD IPS 100 ADVANCE EVENT RECORD IPS 100 TIMER RECORD IPS 100 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t SELECT BACK gt NEXT ENTER IMAGE SIZE You can only select CIF QUALITY Select one of the four quality options SUPER BEST BEST HIGH and NORMAL MANUAL RECORD ENABLE Start stop the manual recording function EVENT RECORD ENABLE Start stop the event recording function When this function is enabled the recording will be triggered by any motion or external alarm ADVANCED OPERATION 5 TIMER RECORD ENABLE Start stop the timer recording that is activated according to the scheduled time 6 MANUAL RECORD IPS Select the images per second for MANUAL RECORD 7 EVENT RECORD IPS Select the images per second for EVENT RECORD Recording that is triggered by a motion 8 TIMER RECORD IPS Select the images per second for TIMER RECORD Recording that is activated according to the scheduled time 4 3 TIMER In this menu list you can schedule different sets of time for recording and detection function Move to TIMER and press ENTER You will see the screen similar as follows QUICK SEARCH RECORD TIMER RECORD DETECTION TIMER TIMER DATE ADVANCE PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT BACK gt NEXT lt lt ENTER 1 RECORD TIMER Press A Y to change the setting ON OFF When it s set to ON press ENTER to go to its submenu fo
5. backup process a file player will also be copied into your disk and you will see a message BACKUP PLAYER shown on the screen After USB backup is completed BACKUP SUCCESS will be prompted on the screen Remove your USB flash drive from the DVR Insert your USB flash drive into your PC Install the file player PLAYER EXE and double click any backup file to play it directly in your PC and see if the backup is successful Note The supported PC operation systems are Windows Vista XP amp 2000 REMOTE OPERATION 5 REMOTE OPERATION You can also control the DVR remotely via the supplied licensed software Video Viewer hereafter called the Video Viewer IE web browser and Apple s QuickTime player ONLY when your DVR supports the network function 5 1 Video Viewer 5 1 1 Installation amp Network Connection 1 Install the software Step1 Place the supplied CD into your CD ROM or DVD ROM drive The program will be automatically run User s Manual amp AP e ES User s Manual fa Download The Latest Version Quick Start fa Download The Latest Version Licensed software 4P Download The Latest Version Step2 Click Licensed Software AP to install Video Viewer immediately or click Download The Latest Version under Licensed Software AP to download the latest version of Video Viewer from the Internet Step3 Follow the on screen instructions to finish the installat
6. lt PAL gt SUPER BEST BEST HIGH NORMAL SATA One HDD Deletes HDD data efficiently 1TB within 2 seconds Video Compression Format Image Quality Setting HDD Type HDD Storage HDD Quick Cleaning Manual Timer Motion Remote 120 IPS for NTSC 100 IPS for PAL Recording Mode Refresh Rate Audio I O 4 audio inputs 1 audio output Mono Motion Detection Area 3 pre defined areas selectable Motion Detection Sensitivity One parameter with four sensitivity levels HIGH NORMAL LOW OFF Pre alarm Recording Yes 8 MB Backup Device 1 USB Flash Drive 2 Network USB Interface Front panel 1 Web Transmitting Compression Format Ethernet 10 100 Base T Supports remote control and live view via Ethernet Licensed software Video Viewer Internet Explorer Remote Operation Software Mozilla Firefox web browser and QuickTime player Operating System Windows Vista XP 2000 Apple Mac TCP IP PPPOE DHCP DDNS Network Protocol 0 Key Lock Video Loss Detection E o Camera Title Video Adjustable Support up to 6 letters Hue Color Contrast Brightness YY MM DD DD MM YY amp MM DD YY E DC 19V lt 42 W 10C 40C 50 F 104 F 345 W x 60 H x 223 D Date Display Format Daylight Saving Power Source Power Consumption Operating Temperature Dimensions mm lt lt lt U System Recovery System auto recovery after power failure The specifications are su
7. product must be collected separately at the product end of life This applies to your product and any peripherals marked with this symbol Do not dispose of these products as unsorted municipal waste Contact your local dealer for procedures for recycling this equipment x e This apparatus is manufactured to comply with the radio interference requirements Disclaimer We reserve the right to revise or remove any content in this manual at any time We do not warrant or assume any legal liability or responsibility for the accuracy completeness or usefulness of this manual For the actual display amp operation please refer to your DVR in hand The content of this manual is subject to change without notice The product amp company names mentioned herein may be the registered trademarks or tradenames of their respective owners GPL Licensing This product contains codes which are developed by Third Party Companies and which are subject to the GNU General Public License GPL or the GNU Lesser Public Licence LGPL The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding author Further source codes which are subject to the GPL licenses are available upon request We are pleased to provide our modifications to the Linux Kernel as well as a few new commands and some tools to get you into the code The codes are provided on the FTP site and please download them
8. your DVR The user name and password are the same as the ones you use to log into Video Viewer If the information is correct click OK to go on If not click Cancel to quit the accessing QuickTime Intemet Authentication x Usend office Password aiii Cancel Note If you re not prompted to enter the authentication information and the error message 10060 appears go to Edit gt Preferences gt QuickTime Preferences and select Streaming Transport front he drop down list Select Use HTTP and keep the port ID as 80 Step 4 When the login is successful you will see the live view APPENDIX 1 TROUBLESHOOTING APPENDIX 1 TROUBLESHOOTING Please refer to the table below for easy troubleshooting The table describes some typical problems and also their solutions Please check them before calling your DVR dealer FAQ Frequently ask question Questions Solutions No power Check power cord connection Confirm that there is power supplied from the outlet DVR is not working when pressing any button You might be under Key Lock mode Press any key and enter the password to exit this mode HDD detection failed Replace with another HDD for testing Replace with another HDD cable for testing Can t detect your USB flash drive Replace with another USB flash drive for testing Format the USB flash drive as FAT32 format and try again No live video
9. 000 and Apple Mac Step 1 Go to Apple s official website to download QuickTime The website address is as follows http www apple com quicktime win html a Click Free Download to go into the download page and select to download the free player b Leave your Email address and click Free Download Now to download the latest QuickTime player c When the download is completed execute the Quick Timelnstaller exe file and follow the on screen instructions to finish the installation procedure Step 2 Open your QuickTime player Select File Open URL in New Player and key in the URL address The URL format is rtsp ipaddress live h264 For example rtsp 59 124 231 75 live h264 Click OK to continue content_guide 12 16 2008 mov File Edit Movie Favorites Window Help gt New Player Ctd N Frae TV gt Store Only South Park Tre First 10 25 Discouurt ur Seasun HBO Zest Of Colections x Favorites TV Seasons for Under 15 Specia Prong Movies of the Week reat Movies Urder 10 Mamma Mia Erittney Spcars Now Acloax Mov Gives You Hell The Murrey ho All Armenean Rej New Release Mov Single Ladies Put a Ring On 2 Cheetah Girls 3 Mie z Pussycat Dolls a YE Games for your we o iPhone or iPod Touch a Click Here Step 3 A pop up window will appear and prompt you to enter the authentication information Key in the user name and password for accessing
10. 2X Note During playback the image size of the recorded data will be shown on the screen BASIC OPERATION 2 Pause Image Jog Press PAUSE to pause the playback In the pause mode Press P once to get one frame forward Press lt once to get one frame rewind 3 Stop Press STOP under the playback mode and the screen of this device will return to live monitoring mode 4 Slow Playback Press SLOW to get 1 4X speed playback and press twice to get 1 8X speed playback 3 4 Search 1 Search by List To quickly search the recorded files by events press LIST to show the following lists RECORD LIST List all the manual recording data MOTION LIST List all the motion recording data TIMER LIST List all the timer recording data FULL LIST List all the recording data QUICK SEARCH Enter the time search menu For details please refer to 4 1 QUICK SEARCP at page 10 Choose 4 enter the list you want Select one event item and press ENTER to start video playback 2 Search by Time Press MENU and select QUICK SEARCH to enter the quick time search menu You can search any specific events by time Year Month Day Hour Min and directly play the file you find 3 5 Firmware OSD Upgrade By using USB flash drive Step 1 Format the USB memory device as FAT 32 format first Step 2 Get the upgrade files from your distributor and save the upgrade files in your US
11. B flash device do not change the file name Step 3 Insert your USB flash drive into the USB port Wait till the DVR detects your USB flash drive Step 4 Press MENU and move to ADVANCE SYSTEM Move to UPGRADE START and press ENTER Step 5 Select YES and press ENTER to confirm the upgrade Step 6 Wait till the DVR is rebooted and initialized ADVANCED OPERATION 4 ADVANCED OPERATION 4 1 1 2 3 4 2 1 2 3 4 QUICK SEARCH You can search any specific events by time and directly play the file you find from the DVR Move to QUICK SEARCH and press ENTER You will see the following submenu items TIME SEARCH QUICK SEARCH DATE 2009 JULY 10 21 30 00 RECORD SEARCH HDD ALL HDD TIMER START DATE ADVANCE PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING ty SELECT BACK gt NEXT ENTER DATE Select the specific time period YEAR MONTH DAY HOUR MIN that you want to search SEARCH HDD Change to the HDD you want if there are more than 1 HDD in your DVR START Move to START and press ENTER button to search and directly playback the recorded files RECORD Move to QUICK START gt RECORD and press ENTER The screen will show the following submenu items RECORD IMAGE SIZE QUALITY QUICK SEARCH MANUAL RECORD ENABLE ON RECORD EVENT RECORD ENABLE ON TIMER TIMER RECORD ENABLE ON
12. D HDD MASTER 1 ALERT UPGRADE START SYSTEM AUTO KEYLOCK SEC NEVER NETWORK LANGUAGE ENGLISH BACKUP VIDEO FORMAT NTSC HDD INFO VERSION 1156 1039 1014 1028 EVENT LOG PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT BACK gt NEXT ENTER The submenu items are described below PASSWORD Reset the password for accessing the DVR system You can set the 4 digit password RESET DEFAULT Press ENTER to reset all settings as default and select YES to confirm or NO to cancel CLEAR HDD Select the HDD you want to clear Press ENTER and select YES to confirm to clear HDD or NO to cancel UPGRADE For upgrading firmware OSD Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 format first Then save the upgrade file in a compatible USB flash drive and insert it into the USB port at the front panel Press ENTER and select YES to confirm upgrade or NO to cancel Note For the list of compatible USB flash drives please refer to APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST at page 24 ADVANCED OPERATION 5 AUTO KEYLOCK SEC Set the time out in second after which the key lock function is activated NEVER 30 60 120 6 LANGUAGE Multilingual OSD Select the language of the OSD 7 VIDEO FORMAT Here shows the information of the DVR video system NTSC PAL Note The DVR will automatically detect and switch t
13. DIGITAL VIDEO RECORDER USER MANUAL Please read instructions thoroughly before operation and retain it for future reference 041 MANUAL V0 9 IMPORTANT SAFEGUARD CAUTION RISK OF ELECTRIC SHOCK CAUTION To reduce the risk of electric shock do not expose this apparatus to rain or moisture Only operate this apparatus from the type of power source indicated on the label The company shall not be liable for any damages arising out of any improper use even if we have been advised of the possibility of such damages Graphic Symbol Explanation The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance gt gt All lead free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances ROHS directive which means our manufacture processes and products are strictly lead free and without the hazardous substances cited in the directive A O sl Y conform The crossed out wheeled bin mark symbolizes that within the European Union the
14. IC ey Mee Gy channel Audio channel Es Digital zoom l Q Digital zoom mode Timer recording unselected unselected 3 2 Recording When the recording and the pre alarm function are activated this device will overwrite 8GB data from the oldest for continuous recording without notice 1 Manual Recording Icon By defaults when the DVR is properly connected with cameras and the HDD is installed you can see a recording on the screen 2 Event Recording Icon When the motion detection function is activated you will see Sy motion on the screen for any motion event 3 Timer Recording Icon When the timer record is activated you will see the LED light of Timer is on and Q gt timer on the screen 3 3 Playback Press PLAY on the DVR control panel and the device will playback the latest recorded video Note There must be at least 8192 images of recorded data for playback to work properly If not the device will stop playback For example if the IPS is set to 30 the recording time should be at least 273 seconds 8192 images 30 IPS for the playback to work properly 1 Fast Forward Fast Rewind You can increase the speed for fast forward and rewind on this device In the playback mode Press FF once to get 4X speed forward and press twice to get 8X speed etc And the maximum speed is 32X Press REW once to get 4X speed rewind and press twice to get 8X speed etc And the maximum speed is 3
15. NETMASK 000 000 PRIMARY DNS 001 001 SECONDARY DNS 055 244 PORT 0080 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT BACK gt NEXT lt lt ENTER Note This DHCP function needs to be supported by a router or a cable modem network with DHCP services and a DDNS account to correspond the dynamic IP address to a specific Hostname for this function to work properly ADVANCED OPERATION 4 7 BACKUP In this menu list you can choose to make a copy for a specified period time to a compatible USB flash drive for your own purpose ADVANCE BACKUP CAMERA USB BACKUP DETECTION DISPLAY ALERT SYSTEM NETWORK BACKUP HDD INFO EVENT LOG A file player will also be copied into your USB flash drive while video backup is in progress To play the backup file you need to install the file player into your PC first Note Before making a video backup with audio you need to make sure whether there s any audio camera connected to the channel which supports audio recording and there s any recorded data for the channel 4 7 1 USB BACKUP Before making USB backup please check if a The USB flash drive is supported by your DVR If not the message USB ERROR will be shown on the screen For the list of the compatible USB flash drives please refer to APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST at page 24 b The format of your USB flash drive is FAT 32 If no please format i
16. at page 10 Choose 4 enter the list you want Select one event item and press ENTER to start video playback 6 SLOW In the playback mode press to show slow playback 1 ZOOM In the live or playback mode press to enlarge the image of the selected channel 8 EE Press to switch to 4 cut display mode 9 SEQ Press to display each channel one by one in the full screen and press again to escape the sequence mode 10 SNAP Press SNAP to take a snapshot Note Before taking a snapshot insert a compatible USB flash drive into the DVR USB port for snapshot saving For the compatible USB flash drive list please refer to APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST at page 24 11 PLAY Press to playback the recorded data 12 PAUSE STOP REW FF In the playback mode press one of these buttons to pause stop fast rewind fast forward the playback file 13 A V 4 Press one of these buttons to move the highlight up down left right In the function setting mode press A Y to change the setting value 14 USB port APPENDIX 1 PIN CONFIGURATION To quickly backup or upgrade firmware OSD you can insert a compatible USB flash drive into this USB port Before using the USB flash drive please use your PC to format the USB flash drive as FAT32 first 1 2 Rear Panel 1 VIDEO IN 1 4 INPUT Connect to video sources such as cameras Note If you want to make a video backup with au
17. bject to change without notice The DVR supports one HDD capacity up to 1TB and HDDs are optional Dimensional tolerance 5mm
18. dio please make sure whether your DVR supports the audio function and connect audio cameras to the channels which support the audio function 2 VIDEO OUT Connect to MAIN monitor for video output 3 AUDIO OUT Connect to an audio device such as a speaker 4 AUDIO IN Connect to an audio source such as a camera equipped with the audio function Note The camera must also be connected to VIDEO INPUT 1 for the audio recording function to take effect 5 LAN Connect to Internet by LAN cable 6 LINK ACT When your DVR is connected to the Internet this LED will be on 7 DC 19V Connect to the supplied adapter FRONT AND REAR PANELS 2 CONNECTION AND SETUP Note The DVR is designed to automatically detect the video system of the connected cameras NTSC or PAL To make sure the system detection is correct please check if the cameras are connected to the DVR and power supplied before the DVR is powered on 2 1 HDD Installation The HDD must be installed before the DVR is on Step 1 Loose the screws on the upper cover and open the upper cover of the DVR Step 2 Remove the HDD bracket Step 3 With the PCB side facing up connect the HDD to the power connector and the DATA BUS connector Step 4 Slide and fasten the HDD to the HDD bracket two screws for each side Step 5 Replace the HDD bracket back to the DVR base Step 6 Close the upper cover of the DVR and fasten all the screws you loosened in Step 1 2 2 Camera Connection
19. en when the login information is correct Note The buttons and functions described below may differ from the actual ones and are for selected model s only bl bal tl al 0000 0O00 0 000 NO Function Description Click a to go to the main page of the DVR Click to go to the detailed DVR setting JOE 3 Channel Selection E Click one of the number to switch to the channel you want to see in full screen Click or A to go to the previous next channel or change setting 5 Display Mode mm Click to show 4 cut display Click to display each channel one by one starting from CH1 When the last channel is displayed it will start from CH1 again To exit from this display mode press any other channel display button Menu and Arrow Keys i Click to enter the menu exit the menu mode Move the cursor up down to select the previous next menu or sub menu function or change the setting Move the cursor left right to the previous next sub menu items 7 Evet Click B to enter the playback search settings screen Snapshot Click E to take a snapshot for the current view and open another browser window to display the captured image 9 Key Lock Click to enable the DVR key lock function To unlock the DVR key in your password and press ka Click to confirm the setting or enter your selection Digital Zoom Click to zoom in out the selected channel image REMOTE OPERATION NO F
20. from the following site or you can refer to your distributor ftp ftp dvrtw com tw GPL AV074 Version Firmware 1156 1039 1014 1028 TABLE OF CONTENTS 1 FRONTAND REAR PANEL S wise cece cece cases ese ate eee ne eee eee eee e O ee 4 A ae l tatseess sad cones A aaidinavanctusadia ein ded arb a 4 AN e e O A ea ee eee EE EEE ee eee ee ere eee ne eee 5 2 ONNECTIONAND SETUP Sosa O a T E o setter eat 6 2AB Instala onana A O NA aa 6 22 Camera COMME CIO Ni dd dd dd da dad 6 A A a a lathe gi geieutoaia 6 2 Ae Date and NME SS INO eia faahee nae A if 6 2 9 PassWord Seling cn ii ie ae ca lc ei i nc rh ee acl rd i alc ie acy ie aie aac 7 EOS ee ON aoe ea lcs eee oe dao a loas 8 i Ms PIG F Lo ROCA ME oi ECO E nn II A 8 32 AAA AI woedatie a a aa a dali nditae ibaa lotus a a iin titular edna a hadatsades 8 23 FMA AC sah eel at cinta a ntact a a dg oe ad erect a ub wags apy encased slats Skagen tne tatal need ied Va Svante day an 8 A acide aogier eau auadannenmp ede ae talus nian a tiated aeteenseamuensalladetedeananeacnancowae 9 3 0 PifmWware OSD Ubud soda dde co a 9 A ADVANCED O PERA TON it de a a 10 4 a 62 Gs 7 02 ere A ne a o eee 10 ARE C ORO re ee ee Re eR RE bio 10 A eee en 11 AA DETECTION ornan de A E tae tes dos en 12 A A o o ee RN nr ee eee eee ee ener eee ee Te rea 13 AO NETWOR K cscs in id eee erate och seth nolan dase a he sees gap edad eo ay tea ta awed odia oie e dia 14 NA O aei iret gi a 14 EOI OE asus ees
21. hance aaah cease e e ot aide a ds hasta ato E A A 14 103 DHCP asi acai che cts eect A A A de eee 15 O a Pe arcs ee A See cca imsh one na ee seem nate ees gem ged nae oe cee ate need setae nate aac een A nace E 16 BT Vis SB DAT ts 16 O REMOTE OPERATION sastre das O A ia es ra acta 18 Dl Video VI WV CM A A damuaaa Sakae A 18 151 IMstallation S Network OnMe CHOM a A iaa 18 O52 JE WED BOW id risas 20 D3 QUICK TIMES Playa ni a A ta A dan 22 APPENDIX T TROUBLESHOOTING cacieietcetee o ie ee 23 APPENDIX Z COMPATIBLE USB FLASHDRIVE LIS Tostado isc 24 APPENDIX 3 COMPATIBLE SATA ADD LIS Tiers illes 25 ARPENDIXA SPECIFICATON Ss essa tapon E a a E E D a A a A 26 APPENDIX 1 PIN CONFIGURATION 1 FRONT AND REAR PANELS 1 1 Front Panel 1 1 4 Press one of the channel number buttons to select and display the channel you want 2 LED Indicators HDD The HDD is reading or recording TIMER Timer recording is activated PLAY The DVR is in the playback mode POWER The DVR is powered on 3 MENU Press to enter the main menu 4 ENTER Press to confirm the setting 9 LIST To quickly search the recorded files by events press LIST to show the following lists RECORD LIST List all the manual recording data MOTION LIST List all the motion recording data TIMER LIST List all the timer recording data FULL LIST List all the recording data QUICK SEARCH Enter the time search menu For details please refer to 4 1 QUICK SEARCP
22. he pop out message Failed to backup the recorded files of the DVR from You need to be a supervisor to operate this function the remote PC side Check if the network connection information is correct IP Address Port User Name Password Specify the hard disk HDD Number and channel number Channel within which have the recorded data you need Failed to upgrade the firmware OSD file via USB Check if the USB flash drive is formatted to FAT32 flash drive Check if the firmware OSD files are correct APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST APPENDIX 2 COMPATIBLE USB FLASH DRIVE LIST Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the following table If the USB flash drive is not supported by the DVR the USB ERROR message will be shown on the screen Note Please use your PC to format the USB flash drive as FAT32 m e EI APPENDIX 3 COMPATIBLE SATA HDD LIST APPENDIX 3 COMPATIBLE SATA HDD LIST WD WD3200AAKS 320GB 7200 rpm WD5000AACS 500GB 7200 rpm APPENDIX 4 SPECIFICATIONS APPENDIX 4 SPECIFICATIONS Video System NTSC PAL auto detection H 264 Video Input Composite video signal 1 Vp p 750 BNC 4 Channels Video Output BNC Composite video signal 1 Vp p 750 BNC Maximum Recording Rate CIF 60 IPS 360x240 lt NTSC gt 50 IPS 360x288 lt PAL gt Adjustable Recording Speed CIF 60 30 15 IPS lt NTSC gt 50 25 12 IPS
23. ion When the installation is completed a shortcut icon 422 will be placed on your PC desktop Network Connection gt Local Connection via LAN a b c d LAN is used when it s the first time to remotely access the DVR and you need to configure the network setting of your DVR based on your network type in advance Connect the DVR to your PC via a RJ45 network cable The default DVR values are as follows Item Default Value IP address 192 168 1 10 User name admin Password admin Port 80 Set the PC s IP address as 192 168 1 XXX 1 255 except 10 in order to make the PC and DVR under the same domain Double click 2 icon on your PC desktop to enter the control panel By defaults the Address Book i panel will be displayed on the right side of the control panel Click a Address Book gt 5 Add button to key in the default IP address user name password and port number of the DVR you intend to connect OR Click ice Search gt II Refresh to search the available IP address es of other DVR s under the same domain as your PC s IP address The found address es will be listed and can be added into the address book by clicking ED Add into address book REMOTE OPERATION e Double click the IP address you just added into the address book to log in gt Remote Connection via Internet When the network configuration of your DVR is completed you can access your DVR remotely
24. o the video system NTSC PAL that is the same as the connected video input devices such as cameras To detect and switch to the correct video system the cameras must be connected and power supplied BEFORE the DVR is turned on 8 VERSION Here shows the firmware version information 4 6 NETWORK In this menu list you can set up the network Move to NETWORK and press ENTER button to enter the submenu The submenu items are described below 4 6 1 STATIC 1 NETWORK TYPE Select the network type as STATIC and set all the information needed in the DVR 2 NETWORK INFORMATION IP GATEWAY NETMASK Key in all the network information obtained from your ISP Internet Service Provider 3 DNS PRIMARY DNS SECONDARY DNS Key in the IP address of the domain name server obtained from your ISP Internet Service Provider 4 PORT The valid number ranges from 1 to 9999 The default value is 80 Typically the TCP port used by HTTP is 80 However in some cases it is better to change this port number for added flexibility or security See the example below STATIC NETWORK TYPE STATIC IP 001 012 GATEWAY 001 254 NETMASK 252 000 PRIMARY DNS 001 001 SECONDARY DNS 055 244 PORT 0080 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT BACK gt NEXT lt ENTER 4 6 2 PPPOE 1 NETWORK TYPE Select the network type as PPPOE 2 USER NAME PASSWORD Set the username
25. r further settings RECORD TIMER 10 12 14 16 18 20 22 24 PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS ty e gt MOVE lt lt SELECT X axis 0 24 hours Each time interval within a square is two hours divided into four 30 minutes Y axis Monday Sunday Operation Move to the start time point and press ENTER to set the start time point marked in red color Then press A Y 4 gt to set the timer recording schedule After setup press ENTER to create an ending time point marked in yellow color and press MENU to exit 2 ADVANCED OPERATION DETECTION TIMER Press A Y to change the setting ON OFF When it s set to ON press ENTER to go to its submenu for further settings DETECTION TIMER 0 2 4 6 8 10 12 14 16 18 20 22 24 SUN MON TUE WED THU FRI SAT PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS ty lt gt MOVE lt lt SELECT X axis 0 24 hours Each time interval within a square is two hours divided into four 30 minutes Y axis Monday Sunday Operation Move to the start time point and press ENTER to set the start time point marked in red color Then press A Y 4 gt to set the timer recording schedule After setup press ENTER again to create an ending time point marked in yellow color and press MENU to exit Note This function here is only for detection timer setup and activation 4 4 DETECTION 3 In this
26. submenu you can set up detection related functions Move to DETECTION and press ENTER You will see the following screen DETECTION TITLE DET AREA CH1 NORMAL SETUP CH2 OFF SETUP CH3 OFF SETUP CH4 OFF SETUP PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS t4 SELECT BACK gt NEXT ENTER The submenu items are described below TITLE Show the camera title of each channel set in CAMERA DET Select HIGH NORMAL LOW to activate the motion detection function with different sensitivity for the selected channel or select OFF to disable this function AREA Press ENTER to set the detection area You will see similar screens as the following ADVANCED OPERATION Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection A E a Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection There are three detection areas for your choice Press A or 4 once to broaden the detection area Press VW or P once to narrow the detection area 4 5 SYSTEM 1 2 3 4 In this menu list you can check or change some system settings Press MENU and move to ADVANCE gt SYSTEM Press ENTER and you will see a similar screen as the following ADVANCE SYSTEM CAMERA PASSWORD XXXX DETECTION RESET DEFAULT RESET DISPLAY CLEAR HD
27. t to FAT 32 in your PC c There is no data in the USB flash drive If yes its recommended to clear all data in the USB flash drive before starting the backup Note When USB backup starts it s not allowed for OSD menu operation or network backup in order to keep the consistency of the video data Note You can backup up to 2GB video data for one time USB backup To backup more data please set the time amp channel s you want and start USB backup again USB BACKUP START TIME 2009 JULY 20 13 00 05 END TIME 2009 JULY 21 13 10 05 AVAILABLE SIZE 1960 0MB CHANNEL 01 O E 03 04 HDD NUM ALL HDD START PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS t4 SELECT BACK gt NEXT lt ENTER Move to BACKUP and press ENTER You will see the following submenu items 1 START TIME Select the start time of the backup 2 3 4 9 6 ADVANCED OPERATION END TIME Select the end time of the backup AVAILABLE SIZE Display the available capacity in the inserted USB flash drive CHANNEL Select channels by pressing ENTER to change the symbol in front of the channel number Symbol means that this channel is selected to backup Symbol means that this channel is not selected to backup HDD NUM Select the HDD containing the data you need START Press ENTER to start copying the chosen data to the USB flash drive How to Play Backup File During the
28. unction Description 12 Search Click E to enter the DVR full search menu You can check all the logs here and select one of them to payback Stop Play Rewind Forward T Pause Slow Playback m Playback control Rewind Forward Click once to get 4X fast rewind forward twice to get 8X three times to get 16X and four times to get buttons 32X the highest Slow Playback Click once to get 4X slow playback and twice to get 8X slow playback system first When QuickTime is selected you will be promoted to enter the user name and password to access the server of the DVR BEST HIGH NORMAL BASIC 15 Change Quality Click to change the image quality 4 CIF CIF 16 Change Resolution Click to change the image resolution 4CIF 704 480 CIF 352 240 H 264 QuickTime QuickTime is Apple Inc s multimedia software You need to have QuickTime installed in you operation 14 Web Transmission APPENDIX 1 PIN CONFIGURATION 5 3 QuickTime Player You can also use the QuickTime player to remotely log into the DVR and check the live view only Note QuickTime is Apple s multimedia software You need to have QuickTime installed in you operation system first and you can access the DVR to see the live view If you have installed QuickTime please skip Step 1 Note The latest version of QuickTime is V6 4 at the time this manual goes to press and the supported operation systems are Windows Vista XP 2
29. via Internet a Double click o gt icon on your PC desktop to enter the control panel By defaults the Address Book panel will be displayed on the right side of the control panel b Click ie Address Book gt Add button to key in the IP address user name password and port number of the DVR you intend to connect OR Click E Search gt CEZ Refresh to search the available IP address es of other DVR s under the same domain as your PC s IP address The found address es will be listed and can be added into the address book by clicking AD Add into address book c Double click the IP address you just added into the address book to log in 7 M X H J amp Ap 20091077422 18 03 33 m E a me REMOTE OPERATION 5 2 IE Web Browser Note The supported PC operation systems are Windows Vista XP 2000 Step 1 Key in the IP address used by your DVR in the URL address box such as 60 121 46 236 and press Enter You will be prompted to enter the user name and password to access the DVR If the port number your DVR used is NOT 80 you need to key in the port number additionally The format is paddress portnum For example for IP address 60 121 46 236 and port No 888 please key in http 60 121 46 236 888 into the URL address box and press Enter Step 2 Enter the user name and password the same as the ones used for video viewer login and press OK You will see a scre
30. you will not be able to find the recorded file to backup by time search If users change the date or time accidentally when the recording function is activated it s recommended to clear all HDD data and start recording again Press MENU and enter the password to go to the menu list The default admin password is 0000 Move to DATE and you can set the date time daylight saving in the DATE menu list FRONT AND REAR PANELS DATE 2008 FEB 15 19 15 27 FORMAT Y M D DAYLIGHT SAVING OFF QUICK SEARCH RECORD TIMER DATE ADVANCE PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING t4 SELECT BACK gt NEXT lt ENTER 2 5 Password Setting Press MENU and enter the password to go to the menu list Then Move to ADVANCE to enter the advanced setting menu In the ADVANCE menu move to SYSTEM Select PASSWORD and press ENTER to enter the submenu to set the password four digits The default admin password is 0000 ADVANCE SYSTEM CAMERA PASSWORD XXXX DETECTION RESET DEFAULT RESET DISPLAY CLEAR HDD HDD MASTER 1 ALERT UPGRADE START SYSTEM AUTO KEYLOCK NEVER NETWORK LANGUAGE ENGLISH BACKUP VIDEO FORMAT NTSC HDD INFO VERSION 1167 1012 1022 1017 BASIC OPERATION 3 BASIC OPERATION 3 1 Live Page System time Status bar cod act dedo donar 008 A HDD capacity Motion Recording Channel title O 1 live audio 1 playback audio Key lock Key unlock EI
Download Pdf Manuals
Related Search