TUSB926x SpeedBoost Monitor User`s Guide
Contents
1. from the settings window is checked a message box will appear asking for your confirmation before proceeding Click Yes to install the driver 12 Using the SB Monitor software SLLU129 September 2010 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated User s Guide l ho ER SLLU129 September 2010 Troubleshooting 1 TUSB9260 TUSB9261 Not Detected After Installing SB Driver If you re running the SB Monitor under Windows Vista Windows 7 64 bits remember to always disable the Driver Signature Enforcement each time you start Windows This issue is occurring because the SB Driver is not digitally signed by Windows In order to disable the Driver Signature Enforcement you must press F8 during the machine s initial boot process and disable the Driver Signature Enforcement option from the advanced boot menu This will allow you to install an unsigned driver 2 Transfer Performance is Not Improved After Installing the SB Driver Transfer performance depends on many factors like e Your USB host performance e Internal bus performance i e PCI PCI Express e Your hard drive s performance Regardless of these facts there is some times where during the SB Driver installation your hard drive was being used by another application and so the SB Monitor couldn t disable your device to properly instantiate the driver If that is the case please restart your system so the SB driver can2. TEXAS INSTRUMENTS www ti com Running the Setup Program InstallShield Wizard Complete Setup has completed installing TUSB9260 SpeedBoost Monitor No will restart my computer later Click Finish to exit TUSB9260 SpeedBoost Monitor setup Figure 2 Software Installation Completed SLLU129 September 2010 Installing the SB Monitor Software 7 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated j User s Guide 13 TEXAS SLLU129 September 2010 INSTRUMENTS Using the SB Monitor software 1 Opening the SpeedBoost Monitor Software NOTE For Windows Vista Windows 7 64 bit OS you must press F8 during the machine s initial boot process and disable the Driver Signature Enforcement option from the advanced boot menu This will allow you to install an unsigned driver and this way you won t face any installation troubles when installing the SpeedBoost Driver to your device You can access the SB Monitor application by clicking on the SpeedBoost Monitor shortcut added on your desktop or by going to Start gt Texas Instruments Inc TUSB9260 SpeedBoost Monitor gt SpeedBoost Monitor see Figure 3 Figure 3 SpeedBoost Monitor Software Locations NOTE If you are running SB Monitor under a Windows Vista Windows 7 platform and depending on your User Account Control Settings you may be prompted with a window asking that if you want to allow the program to make changes to
3. statements TI products are not authorized for use in safety critical applications such as life support where a failure of the TI product would reasonably be expected to cause severe personal injury or death unless officers of the parties have executed an agreement specifically governing such use Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications and acknowledge and agree that they are solely responsible for all legal regulatory and safety related requirements concerning their products and any use of TI products in such safety critical applications notwithstanding any applications related information or support that may be provided by TI Further Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety critical applications TI products are neither designed nor intended for use in military aerospace applications or environments unless the TI products are specifically designated by TI as military grade or enhanced plastic Only products designated by TI as military grade meet military specifications Buyers acknowledge and agree that any such use of TI products which TI has not designated as military grade is solely at the Buyer s risk and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use TI products are neither designed nor intended for us
4. work properly NOTE If you re running the SB Monitor under Windows Vista Windows 7 64 bits remember to always disable the Driver Signature Enforcement each time you start Windows SLLU129 September 2010 Troubleshooting 13 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries Tl reserve the right to make corrections modifications enhancements improvements and other changes to its products and services at any time and to discontinue any product or service without notice Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete All products are sold subject to Tl s terms and conditions of sale supplied at the time of order acknowledgment TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with Tl s standard warranty Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty Except where mandated by government requirements testing of all parameters of each product is not necessarily performed TI assumes no liability for applications assistance or customer product design Customers are responsible for their products and applications using TI components To minimize the risks associated with customer products and applications cus
5. 260 device where the SB driver is not installedr SB Monitor will automatically install the SB driver on your new hard drive Ask for user confirmation default setting unchecked If checked before SB Monitor installs un installs the SB Driver to a device a message box will appear asking for user s confirmation Installing the SB Driver NOTE Only TUSB9260 based devices are recognized by SB Monitor therefore SB Driver can only be installed on them SB Driver can be installed into a compatible device either manually or automatically by SB Monitor depending on your settings If the driver is installed in your device the background color of your hard drive s name on the device s list will be green and you will also see a checkmark next to your hard drive s name see Figure 7 Otherwise it means the SB driver is not yet installed on that device Ie ATA SSDSA25H032G1GN USB Device 2 Settings E Close Figure 7 SpeedBoost Driver Installed on Your Hard Drive Using the SB Monitor software SLLU129 September 2010 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com Installing the SB Driver 4 1 Installing Uninstalling the Driver Manually To be able to install uninstall the SB Driver manually the Automatically install the driver for all monitoring devices checkbox in the settings window needs to be unchecked To install uninstall the drive
6. Monitor_Setup exe file and let the Installshield Wizard guide you through the installation process The SB Monitor GUI needs MS NET Framework 3 5 as a pre requisite in order to work properly The installer will guide you through this process in case such NET framework version is not installed on your machine Ensure that you have a proper internet connection since the installation will be performed through a web download directly from the MS site see Figure 1 TUSB9260 SpeedBoost Monitor InstallShield Wizard TUSB9260 SpeedBoost Monitor requires the following items to be installed on your computer Click Install to begin installing these requirements my Pending Microsoft NET Framework 3 5 Web Download Figure 1 NET Framework 3 5 Installation After the NET validation has finished the installer will copy the necessary files to your local disk into the Program Files directory Once necessary files have been copied into your system the installer will give you the option to Restart the system in order to properly update the files It is highly recommended to choose Yes want to restart my computer now and Click Finish when the installer wizard indicates that the SB Monitor software installation has been completed see Figure 2 Installing the SB Monitor Software SLLU129 September 2010 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated 1
7. TUSB926x SpeedBoost Monitor User s Guide User s Guide 5 TEXAS INSTRUMENTS Literature Number SLLU129 September 2010 SLLU129 September 2010 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated IJ TEXAS INSTRUMENTS 1 Definitions scranrinreaceenaneueanaentedrentnentremencradiendatnent terne annee 5 2 Required Equipment iicccicccsccuscscensencmnmentanceastacionmusnnet sciecd datncmngcmsiucleetacsdedscnemennocinematddaancacieetieemniers 5 1 Running the Setup Program cccceeee eee e eee eee eee eee eee eee eee eee esse eee essen 6 1 Opening the SpeedBoost Monitor Software cccceeeeeeeee eee eee eee sees eee e eee eaeeeeeeeeeaeeeeaee 8 2 SB Monitor List Men sm aE a aaa 9 3 SB Monitor SettiNgS 2 22 22 ce2neseunadmerendanntenreeemeunetnanreneaneuentaentrantneneaneen aa 9 4 Installing the SB Driver 2 252424 enrmenenre sen natnestss td suadandeaie feats E ap aAa Eiai 10 4 1 Installing Uninstalling the Driver Manually ccceeeeeeeeeeeeeeeeeeeeeeeeeeeeeneeeeeeeeneeeeneeeeneeeeneeenaeenes 11 4 2 Atitomatically Install The SB Drivel sicciciiad ened Serendeitie unssin den dewenecedieten eile dedans 11 4 3 Automatically Install the Driver on Hard Drive Change cseceeee eee eeeeee eee eeeeeee tease eee eeeeeeeeeeeeeneee 12 1 TUSB9260 TUSB9261 Not Detected After Installing SB Driver 13 2 Transfer Performance is Not Impro
8. ction This document will serve as a user s manual for the TUSB9260 SpeedBoost Monitor GUI It provides details on using the SpeedBoost Monitor software used with TUSB9260 based devices The software is a Windows based tool that provides a fast and friendly way for installing the SpeedBoost Driver to TUSB9260 based device User can select between different types of settings for performing the installation depending on user s needs The term SB is equivalent to SpeedBoost 1 Definitions The following are useful definitions for your reference e GUI Graphical user interface e SW Software VID Vendor ID PID Product ID 2 Required Equipment The following is required in order to use the SB Monitor software e TUSB9260 TUSB9261 based device with the latest firmware e Hard drive attached to the TUSB9260 TUSB9261 based device e USB interface cable Type A connector to Type B connector e PC running Windows XP Windows Vista or Windows 7 32 bit or 64 bit OS e USB 3 0 host already present in your system Windows XP Windows Vista Windows 7 are trademarks of Microsoft SLLU129 September 2010 Introduction 5 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated j User s Guide 13 TEXAS SLLU129 September 2010 INSTRUMENTS Installing the SB Monitor Software Running the Setup Program Extract the setup program on a directory of your choice Run the 9260_SpeedBoost
9. e in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO TS 16949 requirements Buyers acknowledge and agree that if they use any non designated products in automotive applications TI will not be responsible for any failure to meet such requirements Following are URLs where you can obtain information on other Texas Instruments products and application solutions Products Applications Amplifiers amplifier ti com Audio www ti com audio Data Converters dataconverter ti com Automotive www ti com automotive DLP Products www dlp com Communications and www ti com communications Telecom DSP dsp ti com Computers and www ti com computers Peripherals Clocks and Timers www ti com clocks Consumer Electronics www ti com consumer apps Interface interface ti com Energy www ti com energy Logic logic ti com Industrial www ti com industrial Power Mgmt power ti com Medical www ti com medical Microcontrollers microcontroller ti com Security www ti com security RFID www ti rfid com Space Avionics amp www ti com space avionics defense Defense RF IF and ZigBee Solutions www ti com lprf Video and Imaging www ti com video Wireless www ti com wireless apps Mailing Address Texas Instruments Post Office Box 655303 Dallas Texas 75265 Copyright 2010 Texas Instruments Incorporated
10. l the driver on hard drive change checkbox If you have this functionality enabled a popup balloon will appear indicating that the SB Driver installation is in progress upon compatible device detection Please wait for a second pop up balloon to appear confirming that the SB Driver has been successfully installed before starting to use your device NOTE If checkbox Ask for user confirmation from the settings window is checked a message box will appear asking for your confirmation before proceeding Click Yes to install the driver SLLU129 September 2010 Using the SB Monitor software 11 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated I TEXAS INSTRUMENTS Installing the SB Driver www ti com 4 3 Automatically Install the Driver on Hard Drive Change When changing the hard drive attached to your TUSB9260 based device it s normal that the SB driver installation on your device gets lost In order to fix this you can enable the Automatically install the driver on hard drive change option By enabling this option the SB Monitor will automatically install the SB driver on your hard drive if it determines that the SB driver was previously installed on that TUSB9260 based device To disable this functionality you have to go to the settings window and uncheck the Automatically install the driver on hard drive change checkbox NOTE If checkbox Ask for user confirmation
11. r manually you need to click on your hard drive s name at the device s list This will start the SB Driver Installation see Figure 8 ATA SSDSA2SH032G1GN USB Device Figure 8 Click on Your Device Name on the Device s List A pop up balloon will appear indicating that the SB Driver installation is in progress Please wait while a second pop up balloon appears confirming that the SB Driver has been successfully installed before starting to use your device see Figure 9 Installing the Speed Boost Driver Please wait for the confirmation messagge while your s i X i hardware gets properly configured the Speed Boost Speed Boost Driver Installation Succeeded driver is being installed for your ATA SSDSA2SH032G1GN ATA SSDSA2SH032G1GN USB Device is now ready for use USB Device disk Figure 9 Pop Up Balloons NOTE If checkbox Ask for user confirmation from the settings window is checked a message box will appear asking confirmation before proceeding Click Yes to install uninstall the driver 4 2 Automatically Install the SB Driver SB Monitor provides an option to automatically install the SB Driver on every compatible device on your system this is without the need from the user to click on the hard drive s name at the device s list as we detailed above This functionality is enabled by default To disable this functionality you have to go to the settings window and uncheck the Automatically instal
12. tomers should provide adequate design and operating safeguards TI does not warrant or represent that any license either express or implied is granted under any TI patent right copyright mask work right or other TI intellectual property right relating to any combination machine or process in which TI products or services are used Information published by TI regarding third party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof Use of such information may require a license from a third party under the patents or other intellectual property of the third party or a license from TI under the patents or other intellectual property of TI Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties conditions limitations and notices Reproduction of this information with alteration is an unfair and deceptive business practice TI is not responsible or liable for such altered documentation Information of third parties may be subject to additional restrictions Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice TI is not responsible or liable for any such
13. ugh the SB Monitor Settings Window SpeedBoost Monitor Heb j SpeedBoost Monitor Version 1 0 0 0 SpeedBoost Driver Installation J Automatically install the driver for all monitoring devices J Automatically install the driver on hard drive change Ask for user confirmation Run Speed Boost Monitor at startup Hide Apply Figure 6 SpeedBoost Monitor Settings Window SLLU129 September 2010 Using the SB Monitor software 9 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated 10 TA TEXAS INSTRUMENTS Installing the SB Driver www ti com There are four options available through the SB Monitor Settings window Run Speed Boost Monitor at startup default setting unchecked If checked SB Monitor will run always at Windows startup without the need to manually open the application Automatically install the driver for all monitoring devices default setting checked If checked every time that the SB Monitor detects a compatible device the SB Driver will be installed automatically without the need from the user to click at device on the menu item Otherwise users will need to manually check un check every SB compatible device in order to Install Un install the SB driver Automatically install the driver on hard drive change default setting checked If checked if you had previously installed the SB Driver on a specific hard drive and you change the hard drive from your TUSB9
14. ved After Installing the SB Driver 13 SLLU 129 September 2010 Table oF Contents 3 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated 4 IJ TEXAS INSTRUMENTS www ti com List of Figures 1 NET Framework 3 5 Installation eee eens ee eee ee neeeneeeeneeeneeeeeneenneeeeneeeneeeenneeteeeeenenee 6 2 Software Installation Completed eee e eens neat eee n eee e ae ee eens ena eea ee nee teense nase eeeeeenaees 7 3 SpeedBoost Monitor Software Locations eee e eee eee teen ee enaee eee eneeeeeeeeenaeeeeeneeeeeeeaeee 8 4 SpeedBoost Monitor Task Bar ICON cece ee eee eee eae teen neeeee eee eeeeeeeeeeeeaeeeeeeeenaeeeaeee 8 5 Item Menu of the SpeedBoost Monitor ss ssssssesssseseessesseeesesnesseesseses 9 6 SpeedBoost Monitor Settings WindoW 32 82 rte a desessnmanenede dde itanrontenone 9 7 SpeedBoost Driver Installed on Your Hard Drive eee eee e eee e eens seas nese eeeeeeeeee nee eeee 10 8 Click on Your Device Name on the Device s List eee seen eee eeee eee eeeeeeeeeeeeeeeeenees 11 9 POp Up BallOO NS straes dasemeneneenndaedaenesssainrenenenssetenetedeinie a ES E EEEE 11 List of Figures SLLU129 September 2010 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated User s Guide l ho ER SLLU129 September 2010 Introdu
15. your computer Please click Yes Allow After executing the TUSB9260 SpeedBoost Monitor application the following icon will appear on your Task Bar s notification area see Figure 4 SpeedBoost Monitor Figure 4 SpeedBoost Monitor Task Bar Icon 8 Using the SB Monitor software SLLU129 September 2010 Submit Documentation Feedback Copyright 2010 Texas Instruments Incorporated 1 TEXAS INSTRUMENTS www ti com SB Monitor List Menu 2 SB Monitor List Menu If you click on the SB Monitor Icon located at the notification area of your task bar a menu will pop up This is the SB Monitor Item Menu There are two menu items that will appear always in the menu regardless of the SB Monitor compatible devices in your system Close and Settings see the blue square in Figure 5 By clicking at the Close item the application will be terminated The SB Monitor Settings Window will be displayed by clicking at the Settings menu item For every SB Monitor compatible device on your system a menu item displaying your hard drive s friendly name will appear Below each disk menu item users can also check the name of the volumes present on that disk see the red square in Figure 5 ATA SSDSA2SH032G1GN USB Device things Close ur EX Figure 5 Item Menu of the SpeedBoost Monitor 3 SB Monitor Settings The following section contains a brief description of the setting available thro
Download Pdf Manuals
Related Search