TriPollar™ Questions & Answers
Contents
1. The treatment of a pixel laser is done by creating a large amount of holes in the skin up to 200 holes per cm and recovery time of the skin from this treatment takes a few weeks We DO NOT recommend to combine the two treatments together Either you perform the TriPollar treatment first and wait one week before conducting pixel laser treatment or wait 4 weeks after pixel laser treatment and start the TriPollar treatments b IPL IPL treatment for the removal of age spots can be done immediately after a TriPollar treatment c Dermabrasion Dermabrasion can be done one week after a TriPollar treatment d G5 G5 can be done immediately after a TriPollar treatment 59 Is it OK to have a massage with cosmetics such as aroma oil after a TriPollar treatment Cosmetics which penetrate into skin more than normal cosmetics After a TriPollar treatment the skin pores are opened more than normal making the skin more absorptive and more sensitive Therefore it is recommended after a TriPollar treatment to choose materials for massage or treatment that cause less skin sensitivity 60 Is it possible to combine the TriPollar treatment with sauna or infrared light dome If it is possible before or after TriPollar It is possible to combine the treatments regen heats the skin temperature therefore it is better to give a TriPollar treatment after sauna or infrared light dome It is not recommended2. an electronic control mechanism that rotates the controlling pole electrode between the three poles electrodes This avoids overheating of any one pole electrode resulting in a safer treatment with continuous heating eliminating any need for cooling sessions 6 What is the depth of penetration of Mono Polar Bi Polar and TriPollar How does one actually measure the depth What if the fat is too thick Does TriPollar reach the Hypodermis Mono uni polar is a deep and uncontrolled penetration and it has never been properly established where or how it spreads throughout the body In literature there are claims that Mono uni Polar passes through to a depth of 2cm Bi Polar penetration depth is described in scientific literature to be half the distance between the two poles electrodes The TriPollar configuration penetration depth is the distance between the poles electrodes compared to half the distance in Bi Polar as is evident from the theoretical analysis and confirmed by Infra Red pictures The maximum thickness of the Dermis is 5mm and just below the Dermis is the Hypodermis Therefore the TriPollar penetration depth of 20mm will affect at least 15mm of fat and definitely targets the Hypodermis For very fat obese people the depth of 20mm might not reach the full depth of the Hypodermis in one treatment but only a portion of it In such cases it is recommended to repeat the treatment with supplementary sessions in order to
3. it takes 4 5 treatments to start see a long term effect This is quite individual and varies from person to person because of age and skin type and condition This is why Pollogen recommends a minimum of 6 8 treatments In our experience Pollogen Questions and Answers 31 10 07 doc 9 sometimes overweight clients retain water and it can affect the treatment efficacy 57 Why is the pubic area sore after the treatment The Pubis area should not be treated See Training Guide D Combining TriPollar Treatments with Other Treatments 58 Does a TriPollar treatment improve liposuction if applying the TriPollar treatment just before the liposuction The theory being that it melts fat from the fat cells The TriPollar treatments and Liposuction are very different methods and there is no evidence that the TriPollar treatments if performed before the Liposuction procedure will improve the end results On the other hand TriPollar treatments can be very beneficial and are recommended four weeks after liposuction It helps in healing the skin and also induces skin tightening Does combining TriPollar treatments with various other device treatments improve their outcome As a general rule TriPollar RF treatments heat the skin to a depth of 20mm and the goal of the treatment is to create a controlled inflammation This means the skin in the treatment area can be very sensitive for few days a Pixel Laser Fraxel
4. maintain longer Pollogen Questions and Answers 31 10 07 doc 6 34 How many passes are recommended in a treatment procedure If more than one how many and how many minutes rest between passes It is recommended to divide the full treatment area to few smaller sections see Training Guide For example in a stomach procedure there are 4 sections within the treatment area Work in each of the 4 sections consecutively achieving Controlled Inflammation in one section then move on to the next section and so on Once all sections are completed and Controlled Inflammation is achieved you should repeat the process Pollogen recommends 2 passes in a treatment procedure See the Training Guide for more information 35 Can the treatment time exceed the preset time in the device And what will happen if the preset time is surpassed Pre set treatment times and default settings are a recommendation but in no way a barrier The goal is to reach controlled inflammation Reaching this goal is very individual and can vary in time Another important point is to make sure not to go over 42 C on the skin surface Worldwide experience has shown us that there are people with problems with blood circulation that retain a lot of water in the body and treatment time for them may take longer 36 Is there a reduction in size circumference after the first TriPollar treatment In a majority of regen body treatment cases there is reduction in size even a
5. starting point for most people s skin Once the treatment begins the operator must communicate with the patient and adjust the power settings higher or lower See Training Guide for details 31 Where can we achieve the best results body shape age Cellulite reduction Anyone with cellulite and is over 18 years of age The best results can be seen in cellulite grades 2 and 3 More treatment sessions are required for higher cellulite grades Skin tightening The best results can be observed with woman between the ages of 40 60 They have a higher degree of sagging and wrinkled skin but still have enough skin depth and collagen to generate a significant tightening effect Younger skin is not as wrinkled or sagging and older skin starts to lose critical collagen mass therefore treatments are less effective and more treatments may be required Again the variations are great between people and skin types very individual 32 How to select patients for treatment See Training Guide for detailed instructions Cellulite reduction It is recommended to choose those you can visibly see cellulite in the treatment area when client is in the standing position Skin tightening Clients who have aged sagging and or wrinkled skin 33 On the marketing level is it possible to continue having treatments endlessly Clients can have indefinite treatments spaced by at least one week apart However results will not continue to improve forever but should
6. CM The electricity flows through the entire space because of the induced electrical field created by the poles electrodes Electrical field lines can not break and must be continuous thus although the fat cells have a higher resistance electricity still flows through them heats them up 5 There are reports that other RF systems have burned the skin surface Why is it that TriPollar does not damage the skin surface Since TriPollar RF has highly focused concentrated RF energy it does not require high power for good clinical results Older RF technologies mono polar and bi polar are not focused and therefore require much higher energy to achieve clinical results High energy heats the poles electrodes as well as the skin near the pole electrode resulting in pain and a higher risk of burning and skin damage In order to avoid the risk of burns in older technologies i hi and 2 generation RF most of these systems use cooling mechanisms for the skin and or the poles electrodes The result of cooling is less efficient heating of the skin layers It is like trying to heat up a room by turning on the heater and at the same time turn on the air conditioner Within the TriPollar configuration one pole electrode the controlling pole electrode is always working with the other two poles electrodes in a V shape pattern The controlling pole electrode heats up more quickly than the other two Pollogen has developed and patented
7. TriPollar Questions amp Answers Table of contents A RF and TriPollar Technology sarsaaSiiasosecusstiisesinionsnaiasdasonveidalesdaemmnnasuoneseaacmanms 1 B regen SyStEM eccora EE EEA E EEE a a 3 C Pe Polar Treatments sssrin ea a a E E EER 5 D Combining TriPollar Treatments with Other Treatments eeeeeeeeeeeeeeeeeeeees 10 I gy ele aee santa hh te atainioeu aa seabed Hawtnk vaeaten tuna tpeaa lution ne eH bobeiods 12 F Contra Indications s sseeeeeeeesee seset esteet sseseesessesetsseseesststesstssesstsreesesseesesstesessteseesresees 12 A RF and TriPollar Technology 1 What is Radio Frequency RF technology and how does it work Radio Frequency in the context of aesthetic applications is a general method to heat deep skin layers by delivering High Frequency HF F gt 500 KHz 0 5 MHz electrical current via poles electrodes to the body Body cells do not interpret High Frequency electrical current as electricity rather it is treated as an energy source Skin layers act like resistors in series to the HF electrical current and depending on their resistance they heat up to varying degrees much like a light bulb that heats when electricity is passed through In general depending on the frequency of the electrical current fat cells are more resistant to HF electrical current than other skin cells because oil is less conductive to electrical current than water regular skin cells are made most
8. Why does this happen This is a safety feature of the regen device When the Foot Switch is not pressed for 3 minutes the system returns to the choose applicator screen 19 What is the difference between regen device and the TENS machine which is used for cellulite and muscle contraction The TENS machine is used for muscle contraction and does not affect the fat tissue under the skin The TENS machine typically uses very low electric frequency measured in single Hertz compared to RF devices that use very high electrical frequency measured in million of Hertz TriPollar technology provides selective heating of fat under the skin thus forcing the fat cells to release the liquid fat 20 Why can t there be a thermometer in the applicator This is an engineering consideration Pollogen investigated and determined that the potential problems of doing so outweigh the benefits 21 Why can t there be a switch on the applicator instead of the foot switch This is a safety consideration After thorough investigation Pollogen determined that foot switch configuration is safer than hand switch C TriPollar Treatments 22 How long do results last after 6 8 treatments Keeping in mind that the treatment does not stop the aging process For Cellulite results typically last a few months if a regime of diet and exercises is followed For longer term results the customer needs to return for maintenance treatments every 4 8 we
9. ction Laser guided liposuction manufacturers claim that skin healing is faster Since Pollogen cannot verify these claims we cannot comment 65 Times and effects combined with mesotherapy Normally 24hr after Mesotherapy is ok but depends on the actual treatment 66 Ultrasound Normally 24 Hr after Ultrasound is ok but depends on the actual treatment 67 LED devices Normally 24 Hr after LED is ok but depends on the actual treatment 68 Photonic Normally 24 Hr after Photonic is ok but depends on the actual treatment 69 Deep peeling Minimum 4 weeks after deep peeling 70 What about doing the treatment on the area that lots of women have with lots of little capillary the little veins that are very visible on the skin It is not contraindication You can treat the area normally but clients should be aware that few hours after treatment the capillaries may be more visible In rare cases a few capillaries may break but this is not a health problem nor will the effect last very long In such cases you may treat with lower power settings 71 And the big thick veins that stick out Not a contraindication However after treatment the veins may become more visible for a short time Pollogen Questions and Answers 31 10 07 doc 11 E Side Effects 72 This photo is from a patient that seemed to have developed Folliculitis Is it Folliculitis or something else This is most likely not Folliculitis Folliculi
10. e more sensitive skin and hence it is recommended that they be treated with lower power settings and more sessions 75 Antibiotics Not a contraindication 76 Multiple Sclerosis What if the client really insists Should not treat Multiplesclerosis patient If they insist refuse to do the treatment Pollogen Questions and Answers 31 10 07 doc 12
11. eks For Skin tightening results typically last for a few months for longer term results the customer needs to return for maintenance treatments every 4 8 weeks 23 On average how long does the immediate result last Each individual responds differently On average the immediate result of a TriPollar treatment will typically last a few days from the first treatment After every consecutive treatment this period increases until the 5th or 6th treatment when typically the longer term results start to set because of the building of new collagen under the skin 24 Why is the interval of the treatment 1 week Accent s interval is 3 weeks for 3 6 treatments In clinical tests Pollogen s physician determined that 1 week interval will give optimal results for TriPollar treatments Accent manufacturer and clinical papers claim different intervals For example the manufacture recommends having a 2 week interval between treatments however there is one study which recommends twice a week for 4 weeks In another study coming from Japan the recommended interval was 3 weeks for 3 6 treatments 25 Can we treat the same area in intervals of less than one week What happens if we do so Pollogen Questions and Answers 31 10 07 doc 5 The TriPollar treatment heats fat under the skin normally the skin requires at least a few days to complete the process of treatment and it is very sensitive during this period It is possible but interva
12. fficacy that is due to highly focused electrical energy that requires much less total energy and results in no pain during treatment attaining immediate results and an overall shorter treatment course 2 The unique TriPollar TriPollar configuration can achieve variable Pollogen Questions and Answers 31 10 07 doc 1 depths of penetration thereby resulting in simultaneous treatment of deep and superficial skin layers This is important to achieve uniform multi layer skin heating 3 Is there a difference when using higher or lower frequency RF The body tissues have different electrical properties depending on the frequency of the electrical current For example at 1Mhz the electrical resistance of the fat layer is higher by approximately 30 than the electrical resistance of the fat layer at a frequency of 40Mhz thus it is more efficient to use 1Mhz for heating fat layers under the skin On the other hand at 40Mhz it is more efficient to heat water than at 1Mhz As a result 1MHz is more efficient than 40 MHZ in selectively heating fat cells compared to other water based skin cells 4 RF current prefers to flow through low electricity resistance Why then does the RF flow also through fat cells which have a higher electricity resistance and not only through other water based body cells All skin cells are surrounded by Extra Cellular Matrix ECM and connective tissue As a matter of fact approximately 70 of the skin mass is E
13. fter the first treatment See the white paper Waist Circumference Reduction by TriPollar RF Treatment A Case Report by Dr Luis Bril from Spain explanation included on pg 3 37 Why is oil needed on the skin during a TriPollar treatment There are three main reasons Pollogen advises the use of oil on the skin during a TriPollar treatment a To allow smooth movement of the applicator on the skin b To avoid electrical current from flowing on the skin surface and thus short circuiting the poles electrodes Further without the use of oil it can prevent the RF current from penetrating the skin layers c To cover any hair and to somewhat insulate it from the poles electrodes 38 If oil is the insulator and it is used on the skin then how does the RF penetrate the skin layers Electrical current will choose the path of least resistance The RF power in the applicator is more than sufficient to overcome the thin layer of oil between the pole electrode and the skin It is recommended to press the applicator slightly into the skin to achieve even better penetration of the RF current 39 What is the best oil to use and why Pollogen found in clinical trials that the most suitable oil for TriPollar treatments is pure Glycerin oil This particular type of oil is readily available in any pharmacy Other pure unscented massage oil may be used with satisfactory yet not as good results The properties of Glycerin oil have bee
14. hotter Over the temperature of 42 Will it do harm Body proteins start process of denaturation over 42 degrees The amount of denaturation also depends on the length of time this temperature is affecting The longer and the higher the temperature above 42 degrees the more proteins will become denaturated In extreme cases this may cause burns and scarring 52 What about teeth implants Or metal fillings No problem In case of client discomfort with teeth implants it is recommended to use cotton roll or water roll inside the mouth to increase the distance between the skin and the teeth 53 Why does the skin go dry Can I mix the glycerin with ultrasonic gel When you heat the skin during treatments it is losing its moisture Pollogen recommends using skin moisturizer after treatment You can not mix glycerin with ultrasonic gel because it reduces the treatment efficacy 54 Why does the technician get an electrical shock when working the machine This should never happen Either the technician is doing something wrong or that the machine is not functioning correctly and the service engineer needs to check it 55 Why does the treatment have no effect on my client a few days before her period Female period is not the reason for not obtaining desirable affect Please check how the treatment is administrated 56 Why does the treatment not have affect after 3 times to a client a bit over weight but normal In Pollogen s experience many times
15. ls of less then 1 week will typically require using lower power settings than recommended and will then likely achieve less than optimal results 26 What is the targeted maximum skin temperature The targeted skin temperature should be 40 C for a few minutes but skin temperature should be kept below 42 C 27 1s there any danger for increasing the temperature too fast There is no danger as long as the temperature of the skin is always kept below 42 C However it is not recommended to increase the temperature too fast Slower is better as these are biological processes that need time 28 Is it better to reach maximum temperature faster or slower Increasing the temperature at a slower rate is better for the efficacy of clinical results This is will give more time for the fat cells to release the liquid fat 29 It seems logical that lymphatic drainage treatment will enhance the TriPollar treatment When should such treatment be provided This is correct It is the best to provide such treatment just before or within 24 hours after the TriPollar treatment has been completed 30 Is it better to treat with higher or lower energy Using higher energy can achieve a faster increase of temperature within a given treatment time Pollogen recommends for treatment safety and better efficacy to use lower energy for a longer time during treatment to reach a temperature of 40 C on the skin The regen default power settings are a good
16. ly of water and fat cells are mostly oil and therefore fat cells heat up more quickly than other skin tissue 2 What is TriPollar RF Technology There are three key RF technologies a Mono polar This first generation RF technology uses one pole electrode to deliver the electrical energy and uses a return pad connected to the leg or back to close the electrical circuit The electric current passes through a large part of the body and normally most of it will flow through the vascular system thus not heating the fat cells efficiently b Bi polar The second generation RF technology uses two poles electrodes to deliver the RF energy to the skin The RF flows between the two poles electrodes and is thereby confined to the treatment area The depth of penetration of bi polar for the treatment site is fixed and is about half of the distance between the two poles electrodes Cc TriPollar RF is the 3 generation RF technology and was introduced by Pollogen Ltd It is proprietary and patented It uses three or more poles electrodes to deliver the RF energy under the skin The energy is controlled and limited to the treatment area The key advantages of TriPollar TriPollar are that the three or more poles electrodes focus the energy in the center between the three poles electrodes Compare this to a laser focus versus a light bulb but with electrical current rather than with light This achieves two key advantages 1 High treatment e
17. n found to be the most suitable for the TriPollar treatment with relation to RF insulation and gliding of the applicator Mineral oil or any mineral based oil MUST NOT be used with any TriPollar treatment 40 Since TriPollar RF increases the skin body temperature then why is there no sweat There is some sweat however it is difficult to see because the skin surface is covered with oil 41 Why is there a feeling more heat in the area near a bone Pollogen Questions and Answers 31 10 07 doc 7 This is because of thinner skin layers in the area of bones The RF energy is more concentrated in thinner skin layers and can cause rapid heating in these areas 42 What is the recommended movement of applicator on the body For detailed information please follow the procedures described in the Training Guide 43 When and on which areas should the different applicators be used It depends on the size of the treatment area Applicator 1 should not be used on face and neck as it is designed for larger areas and longer treatment times Applicator 2 is designed to be used on smaller treatment areas and is suitable for use on face and neck 44 What happens to the liquid fat after secretion Is it absorbed by other parts of the body Heating up the fat cells boosts the metabolic rate of the fat cells and increases secretion of lipid molecules liquid fat into the lymph and vascular systems These lipid fat molecules are either absorbed by o
18. n in the skin When the skin is exposed to UV light it produces more melanin in order to protect the body from this radiation I Always burn never tan II Always burn sometimes tan Pollogen Questions and Answers 31 10 07 doc The skin does not react to heat by production of melanin and since RF energy produces heat and not UV light TriPollar treatments will not adversely influence dark skin individuals 48 For each body part what is the optimal point to conclude a TriPollar treatment For each treatment area the optimal point to conclude a TriPollar treatment is when reaching controlled inflammation Skin temperature should be monitored throughout the treatment using the supplied infra red thermometer See the Training Guide for full explanation and examples 49 Why is TriPollar treatment administered only once a week Our patients want to have quicker results Clinical trials conducted by Pollogen found that optimal results are obtained when interval between treatments is once a week and not more two weeks When treating in less than one week it was found that the skin is too sensitive in most of the cases and the operator have to reduce the optimal power setting thus not achieving the desired clinical results 50 What will happen if we do more The treatment may be unpleasant due to increased skin sensitivity and results are not getting better in most of the cases 51 What will happen if we go
19. n sessions It is not necessary to cool down between sessions Even a few minutes between sessions is enough time for the device to cool completely 15 When do the applicators need to be replaced If good and proper care is taken such as cleaning them after every treatment according to the instructions in the user manual keeping them out of harms way etc then there would be no need to replace the applicators 16 What are the maintenance requirements It is necessary to clean the applicators after every treatment with non abrasive substances as per the instructions in the user manual see maintenance and cleaning instructions in the regen user manual 17 Clinics use electrical warming blankets beds to keep the patient warm during treatments Some mono polar RF devices require turning off the warmer heater during the RF treatment Would this be a requirement during TriPollar treatments as well It is not required during TriPollar RF treatments that the blanket bed be turned off This is due to the fact that TriPollar RF is limited to the treatment area only Mono polar and Uni polar should be used with the blanket bed in the Off condition since this kind of blanket bed uses aluminum material that will conduct the RF power Pollogen Questions and Answers 31 10 07 doc 4 18 The regen device returns to the choose applicator screen 1 2 during the treatment when the Foot Switch is released and causing a pause in operation
20. reach deeper and deeper layers consecutively Pollogen Questions and Answers 31 10 07 doc 2 7 How does TriPollar RF compare to Bi Polar Numerical simulation shows that the TriPollar RF configuration differs in two key ways from a bi polar configuration 1 The comparable in Watts TriPollar RF field is much more concentrated and is focused in the center of the three poles electrodes In a Bi polar configuration the RF field spreads out from the poles electrodes and is not focused or concentrated 2 Additionally TriPollar RF reaches both deep and superficial skin layers simultaneously and uniformly compared to only a fixed depth with Bi polar The depth is a function of the distance between the poles electrodes The difference being that with Bi polar the depth is half the distance and with TriPollar the depth is the full distance between the poles electrodes Figure 1 shows a simulation of the electrical current in a bi polar configuration and Figure 2 depicts a TriPollar configuration The white lines are the electrical currents transmitted into the skin the more density of lines indicates more density of RF power for heating the skin layers It is clear from these simulations that in the TriPollar configuration the power density is much higher than the equivalent power with a Bi polar configuration Figure 1 Bi polar simulation Figure 2 TriPollar simulation B regen System 8 What is the minimum and ma
21. s the brands with a maximum power of 200 800 watts use a mono polar configuration In this configuration the RF current is flowing through a large part of the body Relatively little energy is used to heat the required tissue fat under the skin and one must use very high power to achieve the same temperature elevation of the fat layer under the skin as with the TriPollar configuration With TriPollar s focused and localized energy it achieves much more efficient heating of the required tissue in a shorter time Compare laser light to a normal light bulb laser uses a lot less energy but focuses it and achieves a more focused heating than the bulb TriPollar does not use light but rather its configuration focuses the RF power Moreover because of the use of such high power those other brands must use skin cooling mechanisms during treatment otherwise they can cause the skin to burn Skin cooling reduces the efficacy of the treatment 11 Why is regen s maximum power set to 30W All machines have a set limitation e g cars for the speed Based on current clinical research Pollogen determined that 30W was sufficient power for achieving visible clinical results from the first treatment 12 How long is the life time in operating hours of the R F generator The maximum counter value is 10 000 working hours 13 How many hours in a day can the device be used There is no practical limitation 24 7 14 Does it need to cool down betwee
22. ther fat cells in un treated areas or digested by the liver and excreted by the body through kidneys or digestive system Exercise diet and lymphatic drainage enhance the treatment result by consuming the secreted fat as energy whereby causing loss of weight Without exercise or diet the body weight will not change but rather the fat will be reallocated within the body 45 What is the most effective temperature for the secretion of fat liquid The higher the temperature the better the metabolism of fat cells and the secretion of the lipid molecules liquid fat from those cells Maximum skin temperature should be 40 and should not go over 42 46 What is the normal temperature of the Dermis and how much will it increase during a TriPollar treatment Normally the Dermis temperature ranges between 30 32 C After a TriPollar treatment it should increase to about 40 C Not all body parts will reach 40 C treatment to any skin area should be stopped when controlled inflammation is reached please refer to the Training Guide 47 Does RF affect darker skin differently than lighter skin as with light based devices A common method of assessing the skin s tolerance and reaction to ultraviolet light absorption is by the Fitzpatrick Scale of Skin Classifications see below Skin types to VI The darker the skin the more resistance to UV light absorption The dark color of the skin originates from the amount of melani
23. tis usually develops from Staphylococcus Aureus Staph Folliculitis starts when hair follicles are damaged by friction from clothing blockage of the follicle or shaving In most cases of Folliculitis the damaged follicles are then infected with the bacteria Staphylococcus Staph Iron deficiency anemia is sometimes associated with chronic cases In this case and assuming patient skin is clean the appearance of red spots around the Follicles is a result of what is known as Per Follicular Erythema It is relatively common side effect when treating with heat generating devices This is because in some people the hair shafts in the follicles tend to heat up much more than the surrounding tissue and create the edema in the surrounding follicular skin The result is a more pronounced edema there If this occurs during TriPollar treatment it is recommended to shave the treatment area In any case this condition passes very quickly alone in a few hours 73 Is it OK to drink alcohol after TriPollar treatment It is ok to drink alcohol after the treatment However in general it is not recommended to drink a lot of alcohol The possible side effect may be a car accident for example F Contra Indications All TriPollar and regen contraindications are fully listed in the regen User Manual Any other indication is not contra indicated 74 Can diabetics have the treatment Why Diabetes is not contra indicated However diabetics hav
24. to provide any treatment which heats up the body skin after regen Please advise client to drink more water before the treatment in order to prevent dehydration Pollogen Questions and Answers 31 10 07 doc 10 61 Is it OK to apply BODYTER of Sorisa with TriPollar treatment It is OK to combine the treatment and actually it may help to have faster results TriPollar treatment releases liquid fatty acid from the fat cells The fatty acids are absorbed through the lymph system and the circulatory system The BODYTER increases the circulation and muscle activity burning fat It is important to use only TENSE application of BODYTER but not the Infrared red light It is highly recommended to drink more water before the treatment to prevent dehydration 62 Which dermal fillers Specify each one and why Why not soon after What will happen Is it dangerous It is safe to treat upon the dermal fillers 24h after filler procedure Please note that while it is not contraindication Pollogen does not recommend to treat over the injected fillers because it might reduce the time that the fillers will stay in the skin 63 What are the times with combining with liposuction Why so long Our clients want need it strait after the operation Because the sensitivity of the treatment area immediately after a liposuction This is Pollogen recommendation Doing it sooner may result in pain 64 Is there a difference in times with the laser assisted liposu
25. ximum power output Maximum output power is 30 Watts and the minimum is 1 5 Watts However one should be careful when comparing output power alone and also look at the Flux energy per unit volume figures Flux is more difficult to measure and is estimated using numerical modeling techniques In the regen system the maximum flux is 16 J cm 9 Some vendors advertise the Flux level of their machines what is Flux How is it measured What is the regen s Flux In order to measure the efficacy of RF systems the correct manner of measurement is by measuring how much energy a system is delivering into the skin not on the skin surface but inside the skin layers because treatment efficacy is determined by how much heat is delivered to ALL skin layers deep and superficial Flux is a measurement unit of the amount of energy measured in Joules per unit of volume typically cm Some vendors advertise the flux level on the skin surface measured in Watts cm this number does not tell you how much energy is transmitted into the skin The regen achieves a maximum flux of 16J cm Pollogen Questions and Answers 31 10 07 doc 3 The power indication on the system is the percentage from this maximum flux For example if the indication on the machine is at POWER 50 it means a flux of 8J cm 10 Why is it that the regen maximum power 30 Watts seems low when compared to other brands with a maximum power of 200 800watts In most of the case
Download Pdf Manuals
Related Search