Bifurcation CONTENTS - Rafael Lozano
Contents
1. Handle with care jolting or scratching could cause the lamp bulb to burst during use Using the lamp for long periods of time could cause it dark not to light up or to burst When the pictures appear dark or when the color tone is poor please replace the lamp as soon as possible Do not use old used lamps this is a cause of breakage Cleaning and replacing the air filter The air filter has two kinds of filters inside Please check and clean the air filter periodically When the indicators or a message prompts you to clean the air filter comply with it as soon as possible If the filters are damaged or heavily soiled replace them with the new ones To prepare the new filters make contact with your dealer and tell the following type number Type number UX37191 Filter set ENGLISH u When you replace the lamp please replace the air filter An air filter of specified type will come together with a replacement lamp for this projector Turn the projector off and unplug the power cord Allow the projector to sufficiently cool down Use a vacuum cleaner on and around the filter cover Slide the filter unit upward to take it off from the projector Use a vacuum cleaner for the filter vent of the projector Take the fine meshed filter out while holding the filter cover It is recommended to leave the coarse meshed filter in the filter cover as it is Filter unit Intake vent Use a vacuum cleaner on both sides of the f2. Use only the specified and perfect battery Do not use a battery with damage such as a scratch a dent rust or leakage When replacing the battery replace it with a new battery When a battery leaked wipe the leakage out well with a waste cloth If the leakage adhered to your body immediately rinse it well with water When a battery leaked in the battery holder replace the batteries after wiping the leakage out Make sure the plus and minus terminals are correctly aligned when loading a battery Do not work on a battery for example recharging or soldering Keep a battery in a dark cool and dry place Never expose a battery to a fire or water Keep a battery away from children and pets Be careful for them not to swallow a battery If swallowed consult a physician immediately for emergency treatment Obey the local laws on disposing a battery 18 Caring for the mirror and lens If the projection mirror or lens is flawed soiled or fogged it could cause deterioration of display quality Please take care of the mirror and lens being cautious of handling 1 Turn the projector off and unplug the power cord from the power outlet And cool the projector down by leaving it for a while as it is 2 The lens door can be opened manually Please hold both side of the lens door and slowly open it until it is locked with clicking sound ENGLISH a 3 Wipe softly the mirror and lens with a damped soft cleaning cloth
3. lamp yourself Disconnect If the lamp should break it will make a loud bang when it does ventilate the he plug room well and make sure not to inhale the gas or fine particles that come out from the BOW from the projector s vent holes and not to get them into your eyes or mouth outlet Before replacing the lamp turn the projector off and unplug the power cord then wait at least 45 minutes for the lamp to cool sufficiently Handling the lamp while hot can cause burns as well as damaging the lamp Never unscrew except the appointed marked by an arrow screws Do not open the lamp cover while the projector is mounted on a wall or ceiling This is dangerous since if the lamp s bulb has broken the shards will fall out when the cover is opened In addition working in high places is dangerous so ask your local dealer to have the lamp replaced even if the bulb is not broken e Do not use the projector with the lamp cover removed At the lamp replacing make sure that the screws are screwed in firmly Loose screws could result in damage or injury Use only the lamp of the specified type Use of a lamp that does not meet the lamp specifications for this model could cause a fire damage or shorten the life of this product e If the lamp breaks soon after the first time it is used it is possible that there are electrical problems elsewhere besides the lamp If this happens consult your local dealer or a service representative
4. or electrical shock Only use the power cord that came with the projector If it is damaged consult your dealer to get anew one Only plug the power cord into an outlet whose voltage is matched to the power cord The power outlet should be close to the projector and easily accessible Remove the power cord for complete separation Never modify the power cord NOTICE This product is also designed for IT power systems with a phase to phase voltage of 220 to 240 V Using the cable cover Utilize the cable cover as the guard and blind for the connecting parts 1 Connect the signal cables and the power cord to the projector first ENGLISH u Combine parts as shown in figure and assemble the cable cover 3 Insert the three knobs on the cable cover into the three holes on the projector as shown in the figure Pass the cables through the holes on the bottom of the cable cover ACAUTION gt Be careful not to pinch the cables in the cable cover to prevent damage to the cables gt Use the cable cover that is supplied with the projector Do not attempt any modifications to the cable cover Preparing for the remote control Please insert the batteries into the remote control before using it If the remote control starts to malfunction try to replace the batteries If you will not use the remote control for long period remove the batteries from the remote control and store them in a safe place 1 Holding the hoo
5. to control the air flow inside of the projector has moved Be aware that this is not a failure or malfunction Connecting with your devices Be sure to read the manuals for devices before connecting them to the projector Make sure that all the devices are suitable to be connected with this product and prepare the cables required to connect Please refer to the following illustrations to connect them For details please see User s Manual Operating Guide and Network Guide LL120 22 e When AUTO is selected for the COMPUTER IN or COMPUTER IN2 port in COMPUTER IN of the INPUT menu that port will accept component video signals To use network functions of the projector connect the LAN port with the computer s LAN port or with an access point that is connected to the computer with wireless LAN using a LAN cable Computer VCR DVD Blu ray Disc player point 5 o 2 em saab IES ES CEI ll Oj PEA jo 55 _ uS Eh f D am B 3 En ul MIC AUDIO IN AUDIO IN3 AUDIO OUT S VIDEO i lt E Ej E CONTROL MONITOR OUT 1no oIanv ITET SU f you insert a USB storage device such as a USB memory into the USB TYPE A port and select the p
6. while the lamp is taken out NOTE Please reset the lamp time only when you have replaced the lamp for a suitable indication about the lamp 15 I o O Z LL Replacing the lamp continued HIGH VOLTAGE AA HIGH TEMPERATURE HIGH PRESSURE AWARNING P The projector uses a high pressure mercury glass lamp The lamp can break with a loud bang or burn out if jolted or scratched handled while hot or worn over time Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them In addition if the bulb bursts it is possible for shards of glass to fly into the lamp housing and for gas containing mercury and dust containing fine particles of glass to escape from the projector s vent holes gt About disposal of a lamp This product contains a mercury lamp do not put it in a trash Dispose of it in accordance with environmental laws For lamp recycling go to www lamprecycle org in the US For product disposal consult your local government agency or www eiae org in the US or www epsc ca in Canada For more information ask your dealer e If the lamp should break it will make a loud bang when it does unplug the power cord from the outlet and make sure to request a replacement lamp from your local dealer Note that shards of glass Z could damage the projector s internals or cause injury during handling so please do not try to clean the projector or replace the
7. Bifurcation By Rafael Lozano Hemmer CONTENTS General important information This short section must be read for proper operation Description Operation Cleaning Placement Instructions Detailed technical information A technical reference for preservation maintenance and troubleshooting Calibration Troubleshooting Appendix Technical Drawing and Dimensions Appendix Il List of Components Appendix III Wiring Diagram Appendix IV Projector Manual Appendix V Installations shots Appendix VI Branches General important information Bifurcation Shadow Object 2 2012 By Rafael Lozano Hemmer Technique Computer kinect projector metal motor arduino processor fumigated wood Dimensions projection 175 cm x 122 cm equipment 25 4 cm x 34 5cm x 71 cm HxWxL equipment weight 12 kg crate dimensions 82 cm x 45 cm x 35 5cm Edition Ed 1 6 1AP Description A small Y shaped branch similar to a divining rod is suspended from a thread and moves with the air flow and with a small motor Projected on the wall behind the branch is its shadow allowing you to see the entire tree from where the branch came Bifurcation is the second installation in the Shadow Object series of works inspired by Octavio Paz and Bioy Casares among others who insisted that absence and presence are not opposites PLEASE DO NOT TOUCH THE BRANCH BUT YOU MAY BLOW AT IT Operation 1 Take the piece out of the crate
8. anch5 IMG 6252 jpg Branch7 IMG 6254 jpg Branch2 IMG 6249 jpg Branch4 IMG 6251 jpg Branch6 IMG 6254 jpg Branch8 IMG 6257 jpg
9. and mount it on the wall Hang the tree branch from a thin nylon string 2 Connect the piece to electrical power Use the supplied power cable plug one side in to your wall outlet and the other side in to the small box at the end of the six meter cable The piece runs on 120 volt 60 Hz and 240 volt 50Hz 3 To turn the piece ON plug the above mentioned power plugs in to the a wall outlet Then shortly press the round start button on the small box Wait about 60 seconds until the piece is ready Si for operation A calibration message will appear to ask you to step outside the camera view 5 Fa Startup details E When pressing the start button the projectors lens door will open and the computer will start After 20 seconds the OS X operating system will be done booting and the art pieces software will start A small motor will start turning the tree branch The camera view will be displayed along side a message asking you to step out of sight of the camera view The screen will go white and calibration will take place Once the calibration is done a grey depth camera view will be displayed along side a message announcing the end of calibration Now the 3D shadow of the tree will be displayed and the piece is ready for interaction 4 To turn the piece OFF press the power button on the side of the small box Wait about 60 seconds until everything including the projectors finished their shutdown routi
10. anual of the device gt Be careful not to mistakenly connect a connector to a wrong port Before connecting the projector to a network be sure to obtain the consent of the administrator of the network gt Do not connect the LAN port to any network that might have the excessive voltage gt Before removing the USB storage device from the port of the projector be sure to use the REMOVE USB function on the thumbnail screen to secure your data NOTICE Use the cables with straight plugs not L shaped ones as the input ports of the projector are recessed NOTE If a loud feedback noise is produced from the speaker move the microphone away from the speaker This projector doesn t support plug in power for the microphone The COMPUTER IN1 2 port can support a component signal also The specific adapter or the specific cable is required for a component video input to the projector Connecting power supply Put the connector of the power cord into the AC IN AC inlet of the projector 2 Firmly plug the power cord s plug into the outlet In a couple of seconds after the power supply connection the POWER indicator will light up in steady orange Please remember that when the DIRECT POWER ON function activated the connection of the power supply make the projector turn on ACIN Power cord AWARNING Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fire and
11. are a new lamp If the projector is mounted on a wall or ceiling or if the lamp has broken also ask the dealer to replace the lamp In case of replacement by yourself follow the following procedure 3 Loosen the screw marked by arrow of the lamp cover and then slide and lift the lamp cover to the side to remove it 4 Loosen the 2 screws marked by arrow of the lamp and slowly pick up the lamp by the handle Never loosen any other screws 5 Insert the new lamp and retighten firmly the lamp cover 2 screws of the lamp that are loosened in the previous process to lock it in place While putting the interlocking parts of the lamp cover and the projector together slide the lamp cover back in place Then firmly fasten the screw of the lamp cover Turn the projector on and reset the lamp time using the LAMP TIME item in the OPTION menu 1 Press the MENU button to display a menu 2 Point at the ADVANCED MENU in the menu using the V A button then press the button 3 Point at the OPTION in the left column of the menu EA using the V A button then press the gt button Handle So 4 Point at the LAMP TIME using the W A button then press the button A dialog will appear 5 Press the button to select OK on the dialog It performs resetting the lamp time N ACAUTION Do not touch any inner space of the projector
12. computer down and restart it Appendix Technical Drawing and Dimensions Appendix Il List of Components apple mac mini with osx lion 10 7 x Icd projector hitachi cp aw251n remote control for the cp aw251n replacement can be found here http www newremotecontrol com hitachi catalog_item php catnum HL02772 kinect for xbox arduino uno rs232 level shifter digikey 28560D ND motor controller pololu TB6612FNG arduino enclosure Metal Gearmotor pololu 499 1 25Dx58L mm long active usb cable extender external power button digikey IPR3SAD2 small black box to contain power leads digikey HH 364 1 small fumigated tree branch Appendix Ill Wiring Diagram ri A motor gear box arduino motor and projector control Iz HIE EE e 5V USB cable kinect w mac mini 5V USB cable power bare i men main power line power line button cable power lead connection mac mini computer external power button connection arduino motor projector control projector kinect camera Appendix IV Projector Manual find the extended projector manual at http lozano hemmer com texts manuals cp aw251N pdf Regulatory notices continued About Waste Electrical and Electronic Equipment Equipment Directive 2002 96 EC WEEE The mark indicates the requirement NOT to dispose the equipment including any spent or discarded batteries or accumulators as unsorte
13. correcting the distortion Use the A V cursor buttons to select MANUAL or PERFECT FIT operation and press the button to perform the following MANUAL displays a dialog for keystone correction PERFECT FIT displays a dialog for adjusting the shape of the projected image in each of the corners and sides Use the cursor buttons according to the dialog checking the image Press the KEYSTONE button again to finish this operation Adjusting the volume Use the VOLUME buttons to adjust the volume Muting the sound Press the MUTE button on the remote control To restore the sound press the MUTE or VOLUME button ACAUTION If you wish to have a blank screen while the projector s lamp is on use the BLANK function see the Operating Guide Any other method of blocking the projection light such as attaching something to the lens or placing something in front of the lens may cause the damage to the projector Turning off the power STANDBY ON button Press the STANDBY ON button on the POWER indicator projector or the remote control The message Power off will appear on d A o ol the screen for about 5 seconds Br FO O LAMP O 2 Confirm that there is nothing that the Y lens door hits while closing Press the STANDBY ON button again while the message appears The projector lamp will go off and the POWER indicator will begin blinking in orange Then the POWER indicator will stop blinking and light in st
14. d municipal waste but use the return and collection systems available If the batteries or accumulators included with this equipment display the chemical symbol Hg Cd or Pb then it means that the battery has a heavy metal content of more than 0 0005 Mercury or more than 0 002 Cadmium or more than 0 004 Lead x The mark is in compliance with the Waste Electrical and Electronic Contents of package Your projector should come with the items shown below Check that all the items are included Require of your dealer immediately if any items are missing 2 3 Computer cable 4 Parts of cable cover 5 User s manuals Book x1 CD x1 6 Security label 7 Application CD 8 Wall mount unit and User s manual CP AW250N does not bundle them AWARNING P Do not attempt to install the projector yourself Have your dealer or service center handle all installation work Note that manufacturer will accept no liability whatsoever for accidents or injuries resulting from an incorrect installation or improper use NOTE Keep the original packing materials for future reshipment Be sure to use the original packing materials when moving the projector Use special caution for the lens Arrangement Refer to the illustrations and tables below to determine screen size and projection distance The values shown in the table are calculated for a full size scr
15. dry place If you observe battery leakage wipe out the leakage and then replace a battery If the leakage adheres to your body or clothes rinse well with water immediately Obey the local laws on disposing the battery 10 Turning on the power STANDBY ON button 1 Make sure that the power cord is firmly POWER indicator and correctly connected to the projector o and the outlet POWER us cus 7 Make sure that the POWER indicator is mee FO O steady orange 3 Confirm that there is nothing that the lens door hits while opening Press the STANDBY ON button on the projector or the remote control The lens door opens the projection lamp lights up and the POWER indicator begins to blink green When the power is completely on the indicator will stop blinking and light in steady green MENU INPUT STANDBY ON AWARNING Never look into the projection lens or mirror while the projection lamp lights since the projection lamp ray may cause a trouble on your eyes gt Be careful not to pinch your finger with the lens door to prevent an injury gt Do not place the projector vertically with the lens door open as shown in the figure on the right It could cause malfunction or injury gt Do not stand under the projector mounted on the wall or ceiling when its lens door is opening or closing Moreover do not look at the mirror when the lens door is opening or closing Never touch a lens door or mi
16. eady orange when the lamp cooling is complete Do not turn the projector on for about 10 minutes or more after turning it off Also do not turn the projector off shortly after turning it on Such operations might cause the lamp to malfunction or shorten the lifetime of some parts including the lamp AWARNING Be careful not to pinch your finger with the lens door to prevent an injury gt Do not touch around the lamp cover and the exhaust vents during use or just after use since it is too hot gt Remove the power cord for complete separation The power outlet should be close to the projector and easily accessible NOTE Please power off the projector after any connected devices are powered off This projector has the AUTO POWER OFF function that can make the projector turn off automatically For more information please see the Operating Guide in the CD 14 Replacing the lamp A lamp has finite product life Using the lamp for long periods of time could cause the pictures darker or the color tone poor Note that each lamp has a different lifetime and some may burst or burn out soon after you start using them Preparation of a new lamp and early replacement are recommended To prepare a new lamp make contact with your dealer and tell the lamp type number Type number DT01181 1 Turn the projector off and unplug the power cord Allow the projector to cool for at least 45 minutes 2 Prep
17. een 1280 x 800 a Screen size diagonal b Projection distance 8 D 2 Screen height 8 On a horizontal surface screen size c1 EZ ml Projection distance Screen height screen height ypefinch m m inch m inch m ich 1 5 0 120 47 0 295 116 1 102 L18 ot88 74 05821 181 1 274 20 0256 10 1 10368 145 1 446 63 7 25 705 ENGLISH m 1 618 63 7 10302 154 0 44 175 iron 70 5 Keep a space of 30 cm or more between the sides of the projector and other objects such as walls Do not place or attach anything that would block the lens or vent holes For the case of installation in special conditions such as on the wall or ceiling the specified mounting accessories 1121 and service may be required Before installing the projector consult your dealer about your installation The screen position may shift after installation if the projector is mounted on locations such as the wall or ceiling due to the flexibility of the plastic projector body If readjustment is necessary consult with your dealer or service personnel The projected image position and or focus may change during warm up approx 30 minutes after the lamp is turned on or when the ambient conditions change Readjust the image position and or focus as necessary Since the projector features an ultra short throw be aware that it is required to select a screen carefully to have better performance A soft scre
18. en such as a pull down screen may cause serious distortion of a projected image A hard screen such as a board screen is recommended for use with this projector A high gain screen such as a bead screen that has narrow viewing angle is not suitable for this projector A low gain screen around 1 0 such as a matte screen that has wide viewing angle is recommended for use with this projector A screen with a weave pattern may cause moir on the projected image which is not a failure of the projector A screen that has less moir effects is recommended for use with this projector Mounted on the wall or ceiling AWARNING P Install the projector in a stable horizontal position gt Place the projector in a cool place and ensure that there is sufficient ventilation Do not place the projector where the air from an air conditioner or similar unit will blow on it directly gt Do not place the projector anyplace where it may get wet gt Use only the mounting accessories the manufacturer specified and leave installing and removing the projector with the mounting accessories to the service personnel gt Read and keep the user s manual of the mounting accessories used ACAUTION gt Avoid placing the projector in smoky humid or dusty place gt Position the projector to prevent light from directly hitting the projector s remote sensor NOTE The projector may make a rattling sound when tilted moved or shaken since a flap
19. for lens on the market being careful not to give any damage on the mirror and lens For around edge of the mirror and lens where might be difficult to be wiped out please use an air blower for cameras on the market to clean up To close the lens door properly please take the following procedure 1 Insert the power cord with the lens door opened 2 The power indicator will light in orange and the lens door closes automatically Do not touch the lens door when the door is closing Do not allow anything to obstruct the lens door Cleaning cloth NOTE When the lens door is closed manually it may not shut properly he lens door may not close when the LENS DOOR LOCK function of the SERVICE item in the OPTION menu is set to ON For more information please see the Operating Guide on the CD WARNING Before caring for the projection mirror and lens turn the projector off and unplug the power cord then cool the projector sufficiently gt Do not use a vacuum cleaner to clean the projection mirror or lens since it might give some damage gt Do not use cleaners or chemicals other than those specified in this manual Pay special attention to the mirror and lens as these materials could cause serious damage to either ACAUTION Be careful not to pinch your finger with the lens door to prevent an injury 19 Appendix V Installations shots Appendix VI Branches Branch3 IMG 6250 jpg Br
20. he projector s lens door does not open Try starting the projector using the included projector remote control If this does not help unplug the whole piece from the main power After 5 seconds plug the cable back in and press the button on the small box The computer started and the app crashed after trying to start Find the app s icon in the dock and restart the app The projected 3D shadow is not reacting or is not visible Connect a USB mouse and keyboard to USB port on the small box Double ckick the mouse to reveal the user interface Click on the restart button Find the app s icon in the dock and restart the app The motor which rotates the tree branch is too loud There is a cable that runs from the motor to a small black box This box also has two USB cables entering it One USB cable connects the box to the computer and the other connects to the projector Disconnect the USB that runs to the projector This will shut the power of to the motor After transport the cable cover on the side of the projector is dislodged See projector manual page 9 for instruction on how to re attach this cable cover On startup of the app the RGB video feed is black This means the kinect camera was not initialized correctly The software is programmed to automatically try to reconnect to the kinect camera If this was successful you should see the RGB video If not use the restart button in the GUI to restart the softwares Or shut the
21. ibration during the start up routine Phu sans sul el Rigi ci 15 re Curse anu m T icona Now create a template for your tree branch This only needs to be done ones When you see the 3d tree model or after the grey scale video feed disappears double click with the mouse on to the white background A GUI graphical user interface will appear N a 4 i x AA LT 4 NEA 2A XS IR gt Lm 1 A S mem Se ee Mk 1 i ih A an wu AA O b CN S Y i RE i E P IN i A amp El r Si b e t a Find the button labeled calibrate new branch and click on it The GUI and the 3d model will disappear and the video feeds and a red branch image with a blue skeleton line will appear on top of the video feed With the next 3 clicks on the screen you will tell the software which end of the tree branch is B and C Please click inside the red area at each end B is the bottom of the branch the part that would be closer to the tree trunk C is the end of the smaller branch A is the remaining end the one is most likely in line with point B See the next image for some examples A Branch1 IMG_6247 jpg Branch2 IMG_6249 jpg A Branch4 IMG_6251 jpg Branch5 IMG_6252 jpg C Branch7 IMG 6254 jpg Branch8 IMG 625 jpg After these 3 click the red branch will start moving according to the movements of the actual tree branch Double click any
22. ication about the air filter The projector may display the message such as the CHECK THE AIR FLOW or turn off the projector to prevent the internal heat level rising 17 Replacing the internal clock battery This projector has internal clock that uses a battery When the clock of the network function does not work correctly please try solution by replacement of the battery HITACHI MAXELL part number CR2032 or CR2032H Battery Cover 1 Turn the projector off and unplug the power cord Allow the projector to cool sufficiently 2 After making sure that the projector has cooled adequately slowly turn over the projector so that the bottom is facing 3 Turn the battery cover fully in the direction indicated OPEN using a coin or the like and pick the cover up to remove it 4 Pry up the battery using a flathead screwdriver or the like to take it out While prying it up put a finger lightly on the battery since it may pop out of the holder 5 Replace the battery with a new HITACHI MAXELL Part No CR2032 or CR2032H Slide the battery in under the plastic claw and push it into the holder until it clicks 6 Replace the battery cover in place then turn it in the direction indicated CLOSE using such as coins to fix AWARNING Be careful of handling a battery as a battery can cause explosion cracking or leakage which could result in a fire an injury and environment pollution
23. ine meshed T Filter cover filter while holding it so it will not be sucked in Use a vacuum cleaner for the inside of the filter cover to clean up the coarse meshed filter If the filters are damaged or heavily soiled replace them with new ones SIS SY a Put the fine meshed filter on the coarse meshed one turning its stitched side up Filter coarse meshed Put the filter unit back into the projector Filter fine meshed O Turn the projector on and reset the filter time using the STK Stitched FILTER TIME item in the EASY MENU lt side 1 Press the MENU button to display a menu 2 Point at the FILTER TIME using the W A button then press the gt button A dialog will appear 3 Press the button to select OK on the dialog It performs resetting the filter time AWARNING gt Before taking care of the air filter make sure the power cable is not plugged in then allow the projector to cool sufficiently gt Use only the air filter of the specified type Do not use the projector without the air filter or the filter cover It could result in a fire or malfunction to the projector gt Clean the air filter periodically If the air filter becomes clogged by dust or the like internal temperatures rise and could cause a fire a burn or malfunction to the projector NOTE Please reset the filter time only when you have cleaned or replaced the air filter for a suitable ind
24. k part of the battery cover remove it 2 Align and insert the two AA batteries HITACHI MAXELL Part No LR6 or R6P according to their plus and minus terminals as indicated in the remote control 3 Replace the battery cover in the direction of the arrow and snap it back into place Remote sensor NOTE Try changing the batteries when the remote control malfunctions This remote control works with the remote sensors on the projector using infrared light Class 1 LED The active sensor senses the remote control signal assigned within 60 degrees to right and left and within 3 meters For details see the Operating Guide in the CD Prevent the remote sensors from being hit by a strong ray It may cause malfunction of the projector and remote control 3m approx AWARNING Always handle the batteries with care and use them only as directed Improper use may result in battery explosion cracking or leakage which could result in fire injury and or pollution of the surrounding environment Be sure to use only the batteries specified Do not use batteries of different types at the same time Do not mix a new battery with used one Make sure the plus and minus terminals are correctly aligned when loading a battery Keep a battery away from children and pets Do not recharge short circuit solder or disassemble a battery Do not place a battery in a fire or water Keep batteries in a dark cool and
25. ne The projector is ready to be used again once the lens door is closed If the light situation in the room changes dramatically the piece will adjust its brightness levels and after 15 min the projector will switch to eco mode Cleaning and Maintenance The white metal structure can be cleaned with regular all purpose cleaner Do not use harsh cleaners or rough sponges Placement Instructions The projector structure should be hung parallel to the floor perfectly horizontal in order for the projection to look perfectly straight You might have to use the projector s remote control to adjust the key stoning of the image You can also adjust the projector s tilt by loosening the four screws that attach the projector to the metal structure on the top side of the structure The ceiling height of the exhibition space should be at least 290 cm 114 Mount the projector structure so that the top of the wall plate is at 290 cm Now attach the tree branch to a nylon string and hang it on to the hook The hook can be found close to the camera lenses The distance between hook and tree branch should be about 87 cm 34 The piece has 3 six meter cables running from the projector structure to a small box These cables can be hidden inside a white cable channel or run inside the wall Birurcation Detailed technical information Calibration Mechanical Calibration Software Calibrations First the software does it s regular cal
26. ort as the input source you can view images stored in the device You can connect a dynamic microphone to the MIC port with a 3 5 mm mini plug In that case the built in speaker outputs the sound from the microphone even while the sound from the projector is output continued on next page Connecting with your devices continued Microphone Speakers Monitor system with an amplifier LI USB storage device USB TYPEB HDMI USB TYPEA DC5V 5 0 5A ENGLISH u Xe AUDIO IN2 C AWARNING P Use only the appropriate accessories Otherwise it could cause a fire or damage to the device and the projector Use only the accessories specified or recommended by the projector s manufacturer Consult your dealer when the required accessory did not come with the product or the accessory is damaged It may be regulated under some standard For a cable with a core at only one end connect the end with the core to the projector That may be required by EMI regulations Neither disassemble nor modify the projector and the accessories Do not use the damaged accessory Be careful not to damage the accessories Route a cable so that it is neither stepped on nor pinched out ACAUTION Do not turn on or off the projector while connected to a device in operation unless that is directed in the m
27. r it will recommend keep and reuse the spacers Operation INPUT button INPUT STANDBY ON 5 FOCUS button JO i FOCUS button COMPUTER button VIDEO button Displaying and switching the image Press the INPUT button on the projector Each time you press the button the projector switches its input port in turn You can also use the remote control to select an input signal Press the VIDEO button for selecting an input signal from the HDMI S VIDEO or VIDEO port or the COMPUTER button for selecting an input signal from the COMPUTER IN1 COMPUTER IN2 LAN USB TYPE A or USB TYPE B port 12 Focusing Use the FOCUS and FOCUS buttons on the projector or remote control to adjust the screen focus ASPECT button VOLUME button KEYSTONE button MUTE button Selecting an aspect ratio ENGLISH u Each time you press the ASPECT button on the remote control it switches the aspect ratio of the image in turn D ZOOM button D ZOOM button FOCUS button FOCUS button POSITION button Zooming Use the D ZOOM and D ZOOM buttons on the remote control to adjust the screen size Adjusting the picture position After pressing the POSITION button on the remote control use the A Y lt and gt buttons Press the POSITION button again to finish this operation Correcting distortion Press the KEYSTONE button on the remote control A dialog will appear on the screen to aid you in
28. rror If the mirror is broken the projected image will be distorted Close the lens door and contact your dealer NOTE Please power on the projector prior to the connected devices The projector has the DIRECT POWER ON function which can make the projector automatically turn on For more information please see the Operating Guide in the CD 11 ENGLISH u Adjusting the projector s elevator The projector has Front foot for inclinations and Rear foot for horizontals Spacers on the each elevator foot are installed at the time of shipment and projector is in a condition to be able to just project If necessary detach the spacer and the elevator feet can be manually twisted to make more precise adjustments Front foot Rear foot T gt y des gt e eer ES 3 1 1 Spacer Rear foot Spacer Small AWARNING Keep the spacers away from children and pets Be careful not to let them swallow the spacers If swallowed consult a physician immediately for emergency treatment NOTE The adjustment angle can be adjusted up to plus or minus 1 each of Front and Rear foot After the foot is adjusted it is possible to return it to the state of the shipment with a spacer Install Large on the Front foot and Small on the Rear foot of the spacer If change the setting place of the projecto
29. where to make the GUI appear again If you think you made a mistake with creating the template you can click again on the calibrate new branch button Otherwise you can double click on to the background to make the GUI disappear You can adjust the tilt of the 3D model by using the tree tilt sliders Best practice is to hover the mouse cursor of the slider and use the arrow keys to fine adjust the slider values Now double click on to the background again to hide the GUI Image Frame Calibration As of version 2 8 4 of this software it is possible to adjust the edges of the projected image This is helpful incase the projection is not perfectly straight or one wants to project on to a wall that is smaller then the projected image The menu to adjust these settings is hidden Press the key g on your keyboard This should bring up the main GUI graphical user interface On the top left click on the black rectangle that says 1 Settings You should see new GUI items appearing Click again and again on this same rectangle until it say 4 frame points As seen in the image here enable edit frame and border gradient Then adjust the X and Y positions for each of the four corners left top right top right bottom and left bottom Do this until the projected image is well aligned with the projection wall Troubleshooting After pressing the power button the branch motor start turning but t
Download Pdf Manuals
Related Search