Home
DP350 User`s Manual(V1.2)
Contents
1. 26 DP350 User s Manual 5 Make sure your paper has a clean straight leading edge Open the right and left tractor covers Fit the first holes of the paper over the tractors pins and then close the tractors covers Slide the left tractors to remove any slack in the paper and lock it in place Now the paper is in the ready position Shown as below ig a j i IS i LLL OLOO S ag Ce Figure 3 10 install the tractor paper on the tractors Caution Only to clean the paper jams when the printer is turned off can use the paper feed knob on the right side of the printer Otherwise you may damage the printer or change the top of form position 6 Make sure the printer cover is closed Turn on the printer and press LOAD EJECT to feed paper You can adjust the printing home position according to chapter 2 2 4 When the printer receives data it begins printing automatically Note Do not use the paper feed knob to adjust the paper in position due to the micro range is limited When the adjustment exceeds the up limit or down limit the beeper beeps and the position can not be adjusted further The position is in effect before next adjustment The margin set in the software can cover this adjustment so you had better adjust the top of form position with the software 7 When you finish printing the printer receives no data for several seconds the printer
2. Figure 3 5 install cut sheet 6 Adjust the top of form position according to the steps of micro adjust function if necessary Note Don t feed the paper with paper feed knob or it will influence the paper not feeding properly 3 1 2 Loading Tractor Papers If the print paper is the tractor paper please reference to below 1 Make sure the printer is powered off and open the upper cover of the printer select the correct gap of the printer thought the gap adjust lever as shown in the illustration on chapter 2 7 25 DP350 User s Manual Figure 3 6 adjust the gap adjust lever 2 Close the cover and set paper select lever toward the tractor paper position Figure 3 7 adjust the paper selected lever 3 Pull up the right handle of the tractor to loose the right tractor Shown as below Right handle PL mm e T oa pi POSADAS A L i Right tractor cover Figure 3 8 loose the right tractor 4 Slide the right paper guide after referring to the scale on the printer The printer prints to the right of the position marked Push the right handle of the tractor back to lock it in place Then slide the left paper guide to match the width of your paper but do not lock it Move the paper support so it is midway between the tractors Shown as below e Mi SOS Nii m EXE y Figure 3 9 adjust the distance between the right guide and the left guide
3. Solutions There is paper left in the paper in channel while you change the paper select lever position Return the paper select lever to the previous position and eject the paper Then change the paper select lever position again 4 4 Alignment Adjust Mode Enter the alignment adjust mode to improve the print quality when the printer is used for a long time Note When the gap adjust lever is in the position of 2 or above the printer is in copy mode automatically Users can set the gap adjust lever according to specific paper type cut sheet or tractor paper then adjust the alignment following the steps below 1 Turn on the printer make sure the printer is paper in then turn off the printer 2 In the online mode press and hold on the LOAD EJECT key and TEAR key until the Paper Out and ONLINE indicators blink simultaneously the printer enters the graphic adjust mode and print out the graphic alignment setting 3 After entering the alignment adjust mode press the following keys to adjust the degree of make columns EJECT LOAD Each press this key the even line will move left with one step the adjusted value is increased Press ONLINE key to check the result LF FF Each press this key the even line will move right with one step the adjusted value is decrease Press ONLINE key to check the result TEAR Switch to the next DPI adjust state ONLINE Store and print the current settings 4 Restart the printer and exit the alignme
4. If not move the lever to the correct position 2 If this problem still can not be solved its cause maybe that the paper has come off the tractor Reattach the paper to the tractor Phenomenon 2 Paper feeding is crooked or the paper jammed Solutions 1 Make sure the position of your paper supply can not prevent it from feeding 2 Make sure your paper supply is positioned within 1 meter 3 feet off the printer 3 Make sure the printer upper cover is closed 4 Make sure the tractors positions are correct Position the right tractor at the diamond shaped guide marks 5 Check that the holes on the both sides of the paper are aligned with each other Also make sure the tractors are locked and their covers are closed 6 Check whether the paper specifications meet the standard request according to the Appendix A Phenomenon 3 The paper does not eject completely Solutions 1 May be the page length is too long When using the latter cover tear off the paper having entered the printer then press the LF FF button to feed the paper forward When using the tractors tear off the last paper printed out then press the LOAD EJECT button to feed the paper backward 237 DP350 User s Manual 2 Please make sure the paper length is within prescribed range Refer to the paper specifications in Appendix A Phenomenon 4 When you switch between cut sheets and tractor paper the beeper sounds some times and the online indicator is off
5. 23 2 0 The Gap Adjust keveri qe A doh genes val dele reru A eame 23 Chapter 3 How to Use the Printer ccccseeeeeseeeeeeeneeeeeeeeeeeeeeeeneseeeseaseeneeeeeseeeeeeasseeeeeaseesneeeesesneesnesnensenes 24 3 1 Loading the cd o TE 24 EOI SNS o S 24 3 1 2 Loading Tractor Papers riesene iaa aerae e daa rre 25 3 1 3 Multi part Forms d etie t tee b nu Ete ca eet ir ete Entre rd lota une 27 9 1 4 Label Si ii DAR AAA A Ged ae tne ee ee 28 DP350 User s Manual 9 4 5 Envelopes ob UD aaa citi tad ita 28 3 2 Changing the Printer Settings sss nren aeee e a E N Eae aa ANE enne nennen nennen nennen 29 3 2 1 Setting printer parameter through the control panel sss 29 3 2 2 Online aptitude Parameter S ttinQs ccccsccccceseecesseneetetseneeeeeseeeeeeseeaeesseteaeeseseaaeeeeseniaeeessnees 31 3 3 Printer Setting Descriptions ireann iuas eena aiaa a aa daaa nennen nennen trennen nnne nennen 32 3 4 Restore the Default Settings sssssssssssssssssssssssseeeeee eene nennen nennen nennen nnne nens 34 Chapter 4 Troubleshooting cccsseeecesseeeeeenseneceessseenenscnesneesessseeeeeeeseneceenseneeeesesneneeseseneeseseneesenesenerees 35 4 4 Power SUDDply s iitte A cede dei E panini Au eee et ea tp raa 35 4 2 Prnting Problem s i mtt od tet uds 35 4 3 Paper Handling i o rede erret ecc a e A e e eng And de 37 4 4 Alignment Adjust Mode nn nnn nnn nnn nnn nennen nennen nr 38 Chapter 5 Printer Maintenan
6. DP350 lLPT2 Printer Port LlLPT3 Printer Port O COMI Serial Port O COM2 Serial Port Jolimark MP 310T Jolimark O COM3 Serial Port Jolimark TP220 O COM4 Serial Port zi Add Port Delete Port Configure Port Enable bidirectional support Enable printer pooling Cancel Apply 4 Come out a window of Printer port select Standard TCP IP Port click New port Available port types ThinPrint Print Pork Monitor For VMWare Mew Pork Type Mew Port 5 Come out a window of Add Standard TCP IP Printer Port Wizard click Next 6 Come out a window of Add a port import the IP address reported by the Setting printer s IP address in the Printer name or IP address column Take IP address 192 168 0 240 for example Port name is created automatically after finishing filling in IP address Click Next 16 DP350 User s Manual Add Standard TCP IP Printer Port Wizard Add Port For which device do you want to add a port Enter the Printer Name or IP address and a port name for the desired device Printer Name or IP Address fi 92 168 0 24q Port Name IP 92 168 0 240 lt Back Cancel 7 Come out a window of Port information select User defined in the Equipment style then click setting Come out a window of Additional Port Information Required select Custom in the Device Type
7. Gatewaqy 255 255 255 255 CHARACTER FONT tr SANSSER COURIER PRESTIGE SCRIPT OCR B OCR A ORATOR ENG PITCH Im 12 CPI 15 CPI PROPORTIONAL CHI PITCH cc 7 5 CPI O LINE SPACING DT 8 LPI FORM LENGTH 3 INCH 3 5 INCH 11 3 INCH 4 INCH 5 INCH 5 5 INCH 6 INCH 7 INCH 8 5 INCH mE A4 12 INCH FORM LOCK ON PAGE SKIP ON COMPRESS PRINT ON TEM SETI LANGUAGE E UE CHINESE EMULATION eco IBM HIGH DENSITY f ON PRINT DIR UNI DIR Zn CHAR MODE Zr CHINESE INTL CHAR SET USA FRANCE GERMANY U K DENMARK 1 SWEDEN ITALY SPAIN 1 JAPAN NORWAY DENMARK 2 SPAIN 2 LATIN AM KOREA LEGAL HOLAND TURKEY CHARACTER SET ITALICS car CODE PAGE USA MULTL PORTUGAL GANADA NORWAY EAST EURO CYRILLIC RUSSIAN HUNGARY KAMENICKY TURKEY ICELAND BULGARIA MAZOVIA GRK 437 GRK851 GRK8859 GRK 1253 ARAB NLS ARAB EXT WIN LAT1 WINLAT2 ISO LTN1 ISO LTN2 TUR8859 9 ISO LTN9 KBL LATIN 7 QUITE MODE ER ON COPY MODE ON AUTO LF ON TEAR OFF OFF D TEAR POS BY CONT BY CONT1 BY CONT2 BY CONT3 FORM LEN COVER OPEN OFF D BLACK MARK F ON PIN SWITCH ON ERIAL 1 6 BAUD RATE 19200BPS 000 4800 BPS 2400 BPS 1200 BPS PARITY ca ODD EVEN DATA BIT rt 7 BIT STOP BIT TEN 2 BIT PROTOCOL XON XOFF 1 Please press the ONLINE key to enter the online status the hole down the LF FF key and PARK LOAD key for 3 second to enter SETUP MENU SYSTEM PINTEST 6 om i m RO t a m RI UN TT a s 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 DP350 User s Manual NOTE 1
8. Position 21 ESC v Set Relative Vertical Print Position 22 ESC J n 180 Line Feed 23 ESC j n 180 Reverse Line Feed 24 HT Horizontal Tab 25 VT Vertical Tab 26 ESC m n Reassign Graphics Mode 27 ESC Set Graphics Mode 28 ESC G Select Graphics Mode Image and 29 ESC Print Raster Graphics d 30 ESC K 8 dot Single Density Graphics Mode 31 ESC L 8 dot Double Density Graphics Mode 32 ESC Y 8 dot High speed Double Density Graphics Mode 33 ESC Z 8 dot Quadruple Density Graphics Mode 34 FS amp Set Chinese character mode 35 FS Cancel Chinese character mode 36 FS SO Select Double Width Mode Chinese 45 DP350 User s Manual 37 FS DC4 Cancel Double Width Mode Chinese 38 FS W Select Cancel quadruple size mode for Chinese character 39 FS J Select lengthways printing 40 FS K Select transverse printing 41 FS D Two character lengthways half size mode paratactically printing 42 FS Select Cancel Underline Mode for Chinese character 43 FS S Select full size mode pitch for Chinese character 44 FS T Select half size mode pitch for Chinese character 45 FS U Select half size mode pitch adjustment for character 46 FS V Cancel half size mode pitch adjustment for character css 47 FS x Select Cancel high speed printing print 48 FS 2 Chinese character of user defined command 49 FS Sl Select half size mode for Chinese c
9. SANS SER COURIER PRESTIGE SCRIPT OCR B OCR A ORATOR Set All Set Current 5 The setting way is corresponding with that of printer menu system In the Printer Settings layout select the first class menu in the combobox of Select Printer Setting Class select the second menu in the Configuration and set the item in the current parameters list 6 Click the button Reset All to reset all the parameters to be the driver s default but not change the printer s settings 7 When setting the parameters you can click Set Item to save the current settings after setting each item or you can also click Set All Items after setting all parameters After clicking Set All Item or Set Item the parameter s instruction will be sent to the printer 8 The printer s parameter settings are changed at once after receiving the instruction and the printer does not need to restart 9 After finishing settings click OK exit the Properties window 3 3 Printer Setting Descriptions 1 FONT Select the font contained in your printer to print 2 ENG PITCH Set the pitch to determine the horizontal spacing of the printed ASCII 3 CHI PITCH Set the pitch to determine the horizontal spacing of the printed Chinese 4 LINE SPACING Set the vertical spacing of the printed characters You can set it to either 6 LPI the default setting 32 DP350 User s Manual or 8 LPI 5 FORM LENGTH Y
10. feeds the perforation of the tractor paper to the edge of the printer cover so that you can tear off easily Note Set the auto tear off function on in the Printer Setting Mode Otherwise the printer does not feed the perforation to the edge of the printer cover 8 If the perforation and the edge of the printer cover do not match you should adjust the tear off position following the steps in Micro adjust of the tear position after adjusted tear down the paper When you send print data again the paper automatically feeds back to the printing home position and begins to print How to switch tractor paper to cut sheet paper Firstly tear down the tractor paper which is having been printed then hold LOAD EJECT button to eject the paper in the offline mode Pull the paper select lever to the cut sheet position and load the cut sheet according to chapter 3 1 1 Caution Make sure tractor paper which is having been printed is tore off before ejecting the tractor from the printer as too many pages ejected can cause paper jammed 3 1 3 Multi part Forms The installing ways of multi part forms 4 plies is most and tractor paper are the same Just pay attention to the following tips 1 Must refer to the figure below to lift up the back cover otherwise it may cause paper jam during printing 2 Never load multi part forms joined by metal staples tape or continuous gluing 3 Avoid printing beyond the printable area while printing m
11. has been damaged F If the product exhibits a distinct change in performance indicating a need for service Note The contents of this manual may be changed without prior notice All parts of the printer can be recycled When it is abandoned we can call it back freely Please contact us when you abandon it DP350 User s Manual Warnings Cautions and Notes Pay attention to the following promises when using this manual Warnings Warnings must be followed carefully to avoid bodily injury Cautions Cautions must be observed to avoid damage to your equipment Notes Notes contain important information and useful tips on the operation of your printer The Guide First thanks for buying the Jolimark printer The printer is 24 pin 80 column Dot Matrix Printer can satisfy multi function print requests It can be widely used in tax mail telecom police hospital insurance finance stock customhouse cabaret aviation and transport etc The printer feature introduce as follow e Install print paper easily The install design make you operate easily install paper rapidly and save your time e Tear off function This causes tractor paper to be automatically fed to the tear off position at the edge of the window cover for easy tear off at the perforations after printing This zero tear off capability helps eliminate paper wastage e Facility switch between cut sheet and tractor paper Feed the tractor paper back to the in
12. the select direct carefully Such as select local or Network Printer then click next 4 Come out a window of Select the Printer port select a port you want your printer to use For example select Create a new port select Standard TCP IP Port in the port click next Add Printer Wizard Select the Printer Port Computers communicate with printers through ports Select the port you want your printer to use If the port is not listed you can create a new port C Use the following port LPT1 Printer Port LPT2 Printer Port LETS Printer Port COM1 Serial Port COM2 Serial Port Panama Serial Part zi Note Most computers use the LPT1 port to communicate with a local printer Create a new port Type Standard TCP IP Port lt Back Cancel 5 Come out a window of Add standard TCP IP Printer Port Wizard click Next 6 Come out a window of Add Port enter the IP address reported by the Setting printer s IP address in the Printer Name or IP Address column Take IP address 192 168 0 240 for example Port Name is created automatically after finishing filling in IP address 18 DP350 User s Manual Add Standard TCP IP Printer Port Wizard xj Add Port For which device do you want to add a port Enter the Printer Name or IP address and a port name for the desired device Printer Name or IP Address fi 92 168 0 24q Port
13. then click settings Add Standard TCP IP Printer Port Wizard Additional Port Information Required The device could not be identified The device is not found on the network Be sure that 1 The device is turned on 2 The network is connected 3 The device is properly configured 4 The address on the previous page is correct If you think the address is not correct click Back to return to the previous page Then correct the address and perfom another search on the network If you are sure the address is correct select the device type below m Device Type C Standard Generic Network Card Custom lt Back Next gt Cancel 8 Come out a window of Port Settings Affirm that Port name and Printer name or IP address are correct Protocol is RAW and Port Number is 9100 click OK 17 DP350 User s Manual Configure Standard TCP IP Port Monitor m7 xi Port Settings Port Name IP 92 168 0 240 Printer Name or IP Address fi 92 168 0 240 Protocol Raw C LPR Raw Settings Port Number 5 00 r LPR Settings Queue N ane lh ns LPR Byte Counting Enabled CT SNMP Status Enabled Community Name p ublic SNMP Device Index Cancel 9 Return to Additional Port Information Required click Next 10 Come out a window of Completing the Add Standard TCP IP Printe
14. 0 Network Setting S ee roger errare A A ds 9 1 10 1 Gonnecting Printer ope tiet et do ted a et ee 9 1 10 2 S tting TP Address onte ot b abe Steel e io es eee ee Pea rg eed 10 1 10 3 Installing Printer Network Driver esses eene nnne nnne nennen entr nennen 12 Chapter 2 Control Panel Operations eeeeeeeeeeeeee esee eee nennen nennen nannten nnne nnn nnn nnn nnns 20 2 1 Control Panel label comunican 20 2 2 bED DeSCrFIDLUOF oiii tee tette do ode Bee et inne hae Pee i 20 2 3 Control Panel Basic Function Description essen eene nennen nnn 20 2 4 Other Function Descriptions of Control Panel sssssssssssssseeee ener 20 2 4 1 In the Tractor Paper Mode ooooocococccccococococcccnococinnanonnnnocncncnnnnnnanncnnnn nara cnanan nn ates nsns ensi t rane nei rests nna 20 2 4 2 In the CUE Sheet Mode coccion d ert e tea P AUI e ERE RD REX SE LE Dee EHE RR 21 24 3 Print Speed oe on tuendae at et e ER MEA 21 2 4 4 Micro Adjust of the Printing Home Position and the Tear Position ssssssssss 21 2 4 5 Feed Paper to the Tear Position ooooninicinininicicinnconocccncncncnnnnananncncnnnannnnann nnne nennt nnne nnn sss nnn na 22 2 4 6 Other Functions of the Control Panel oooooconnoccccnnnocicinncancncnnancnncnnnnoncc non nann cnc nnann nn nnne 22 2 5 Paper Select Lever nennen nennen R RRE ennesn nnn nennen nsn nennen nnns 22 2 6 Paper Feed Knob 21 di ia
15. 55 0 IP Subnet Mask then which of printer should be set to 192 168 0 x 255 255 255 0 x 2 254 and should avoid the IP in used It is not restricted for NetFinder to search printers in the same network but different segment parts can not stride gateway Relative glossary of IP address may refer to corresponding information 2 Setting printer s IP address Select the printer information to be modified black frame appears click Assign IP button Set the IP in the dialog box appearing Assign IP Address x Ip 192 168 0 240 Cancel 255 255 255 O Sen EXC Default setting Default Gateway 255 255 295 255 Use DHCP d Reload Timer v Close this window on success 10 seconds remaining Pc Check the Use DHCP if need to assign dynamic address the settings above will be disabled automatically Please make sure there is a DHCP server in the network or the printer can not receive an effective IP address When to specify static address uncheck Use DHCP and fill in IP address Subnet Mask and Default Gateway If there is no gateway in the network fill 255 255 255 255 in the Default gateway IP address and Subnet Mask should obey the assigning rules of local LAN Ethernet please enquire the administrator of networks which the printer connects to for more details Click OK to send address setting information to the specified printer The pr
16. 6 To end the self test make sure the printer is not printing Press LF FF or LOAD EJECT button to eject cut sheet then turn off the printer ASCII Self test mode Jolimark DP350 VX X XXXXXXX XX XX SN 0000000000 W 8 4 0123456789 lt gt ABCDEFGHUKLMNOPQRSTUVWXYZ N ab W 8 amp 0123456789 lt gt ABCDEFGHIKLMNOPQRSTUVWXYZ abcd amp 0123456789 lt gt ABCDEFGHIKLMNOPQRSTUVWXYZT V abcde Figure 1 11 ASCII Self test mode NOTE If the self test did not print satisfactorily see Chapter 4 If it prints correctly go on to the next section 1 8 Connecting the Printer to Your Computer The printer configures with a parallel interface two USB interfaces a serial interface or an Ethernet interface According to specific interface standards Connect the printer to the computer with the correct cables Before you begin place the printer upright as shown below This makes it easier to connect the cable DP350 User s Manual Parallel interface Serial interface Ethernet interface USB interface USB interface Figure 1 12 lay the back of the printer upward Note Before connecting the parallel interface or the serial interface please make sure the power of the printer is shut down Only after tighten the cable could turn on the printer or it will damage the printer 1 8 1 Connecting to the Parallel Interface 1 Turn off both the computer and the printer Plug the par
17. Additional Port Information Required click Next 10 Come out a window of Completing the Add Standard TCP IP Printer Port Wizard click Finish 11 In the selection of Manufacturers Printers click Have Disk and then click Next 12 Come out a window of Install From Disk Please according to the operating system environment such as Windows 2000 XP Vista Win7 operating system you should select the path as follows CD ROM Driver WIN2000 XP Vista Win7 that you can find a file named DP350 inf click open then click OK then return to the window install printer software click next 13 Follow the direct click next gradually till the installation is finish At this time printer network driver is installed completely 2 Upgrade install printer network driver setting driver s network port If PC has installed the printer s driver set driver s network port to carry out network printing The concrete steps are shown below 1 Click Start Settings select Printers 2 Right click DP350 driver click Properties on the window coming out 3 Come out a window of Properties click Ports and Add Ports 15 DP350 User s Manual Jolimark DP350 Properties EN 7 xl Security Device Settings Printer Settings General Sharing Ports Advanced Sy Jolimark DP350 Print to the following port s Documents will print to the first free checked port Printer Port Jolimark
18. CT once the paper will be fed into the printing home position automatically when the paper is at the ready position In the tractor paper mode and pressing LOAD EJECT once the paper will eject one page of tractor paper when it is at the tear position or just feed paper When it is at other positions pressing LOAD EJECT once the tractor paper will eject one line or hold the LOAD EJECT button down the printer will eject one page of tractor paper If in the cut sheet paper mode press the LOAD EJECT button the paper will be entirely ejected from the printer LF FF If the paper is at the print position press the LF FF button once in standby or offline mode the printer will feed the paper one line Alternatively hold the LF FF button down the printer will feed one page of tractor paper or eject the cut sheet paper TEAR In the tractor paper mode in standby or offline mode press TEAR to switch between the tear position and the printing home position SPEED In the offline mode pressing SPEED can switch among the normal mode the high speed mode and the super high speed mode Note In the tractor paper mode if paper is out please press LOAD EJECT or LF FF to feed paper after it has been loaded 2 4 Other Function Descriptions of Control Panel 2 4 1 In the Tractor Paper Mode TEAR 1 In the offline mode if the paper is at the print position press TEAR key once and the printer feeds paper to the tear po
19. INE button 3 seconds when offline till the ONLINE indicator blinks with a beep 2 Hold the TEAR button 3 seconds that you can switch the function of feeding paper to the tear position automatically ON or OFF 2 4 6 Other Functions of the Control Panel KEY FUNCTION LF FF POWER Print pin test mode to test the print pin ifin good condition 2 5 Paper Select Lever Set paper select lever toward the cut sheet or tractor paper position to select cut sheet mode or tractor paper mode Figure 2 2 the paper select lever 22 DP350 User s Manual 2 6 Paper Feed Knob The paper feed knob is used to feed paper or eject paper manually In general it s better not to use it 2 7 The Gap Adjust Lever The gap adjust lever lets you specify the correct setting for your printing material It is factory set for standard office paper POSITION PAPER TYPE 1 reserved 0 Cut sheet 1 2 plies 2 3 plies diia 3 4 plies 4 reserved 5 reserved Figure 2 3 the gap adjust lever 23 DP350 User s Manual Chapter 3 How to Use the Printer Here are the steps of using printer 1 Assemble the printer as the chapter 1 connect the printer to your computer and install the driver correctly 2 Load the correct type of paper 3 Set the printer if necessary 4 Send the print command to the printer to print 3 1 Loading the Paper In addition to printing on cut sheets and tractor p
20. Jolimark User s Manual DP 350 Dot Matrix Printer AAN D 10 11 12 13 14 15 DP350 User s Manual Important Safety Instructions Read all of these instructions carefully and thoroughly and save them for later reference Follow all warnings and instructions in the manual as well as marked on the product If the printer has been used just now please not touch the print head for overheating Do not put your fingers under the tractor cover of the left and right tractor when install the tractor paper Unplug this product from the power outlet before cleaning Do not use liquid or aerosol cleaners Use a damp cloth for cleaning Do not use this product near water Do not place this product on an unstable cart stand or table The product may fall causing serious damage to you or the product Slots and openings on the cabinet and the back or bottom are provided for air ventilation To ensure reliable operation of the product and to protect it from overheating do not block or cover these openings The openings should never be blocked by placing the product on a bed sofa rug or other similar surface This product should never be placed near or over a radiator or heater This product should not be placed in a built in installation or kiosk stand unless proper ventilation is provided This product should never be placed near or over a radiator or heat origin and should avoid of direct sunshine Do not locate
21. Name ip 92 168 0 240 lt Back Cancel 7 Come out a window of Additional Port Information Required select Custom in the Device Type and then click Settings Add Standard TCP IP Printer Port Wizard Additional Port Information Required The device could not be identified The device is not found on the network Be sure that 1 The device is turned on 2 The network is connected 3 The device is properly configured 4 The address on the previous page is correct If you think the address is not correct click Back to return to the previous page Then correct the address and perfom another search on the network If you are sure the address is correct select the device type below m Device Type C Standard Generic Network Card Custom lt Back Next gt Cancel 8 Come out a window of Port Settings Affirm that Port name and Printer name or IP address are correct Protocol is RAW and Port Number is 9100 click OK 14 DP350 User s Manual Configure Standard TCP IP Port Monitor I 2 xl Port Settings Port Name iP_1 92 168 0 240 Printer Name or IP Address fi 92 168 0 240 Protocol Raw C LPR Raw Settings Port Number 5 00 LPRA Settings Bueue Name LPR Byte Eountina Enabled SNMP Status Enabled Community Name public SNMP Device Index Cancel 9 Return to
22. R SET Select character set into Italic Character Table or Graphic Character Table 16 CODE PAGE Select a code page 17 QUIET MODE Select the printer into quiet mode Each line will be printed twice in quite mode 18 COPY MODE Select copy mode function ON or OFF 19 AUTO LF Select ON or cancel OFF the automatic advance of the paper by one line after every carriage return command 83 DP350 User s Manual 20 TEAR OFF Open or close the auto advance paper to tear off position function When the tear off function is opened if the printer doesn t receive data a few minutes after printing the printer will advance the paper to the tear off position automatically 21 TEAR POS Turn off the tear position and select to depend on the content or page length 22 COVER OPEN Open or close the cover sensor 23 BLACK MARK Whether or not choose the black mark detection 24 PIN SWITCH Select pins switch mode The printer auto switches the different pin to print table Line 25 BAUD RATE PARITY DATA BIT STOP BIT PROTOCOL All these items are effect when using serial interface The printer settings are the same with those of the computer 26 PIN TEST Select broken pin mode The default setting is every root and printed needle is live When the printer is printing if user finds out broken pin please select broken pin mode set the corresponding pin is broken then the printer can automatic compensate broken pin positio
23. Solutions The printer may be out of paper Load paper in the printer Phenomenon 3 The printer sounds like it is printing but nothing is printed Solutions 1 The ribbon cartridge may not be installed properly See chapter 1 5 2 The ribbon may be worn out Replace the ribbon 3 The gap adjust lever may be too high If so move it to the corresponding thickness position with the paper 35 DP350 User s Manual Phenomenon 4 The printer makes a strange noise while printing Solutions Turn off the printer and check for a paper jam a ribbon jam or other problems Phenomenon 5 The beeper sounds some times and the ONLINE indicator is off Solutions 1 Switch off the printer and power on again 2 If the ONLINE indicator stays off check for a paper jam or ribbon jam If it does turn the printer off and clear the jam 3 If an error occurs when you switch between cut sheets and tractor paper make sure the paper select lever is in the correct position 4 If the printer still does not work correctly turn off the printer and contact your dealer or a specified Jolimark service center e The print is faint or uneven Phenomenon 1 Printed characters have parts missing at the top or bottom Solutions The ribbon cartridge may not be installed properly See chapter 1 5 Phenomenon 2 The printout is faint Solutions The ribbon may be worn out Replace the ribbon as described on chapter 1 5 The ribbon can not move smoothly So
24. The items in net lines are the current setting 2 When select the compress printing in the setup menu high speed printing is invalid 3 Black mark function is optional It can be set up according to the customers requirement If the fittings of black mark do not install the black mark item should be closed 4 If printer hasn t installed Ethernet interface it will not print out the relative Ethernet information of MAC and IP when it runs self test or menu printing 1 Make sure the printer is in online mode ONLINE light is on at the same time holding the LOAD EJECT FF LF keys for 3 seconds e The Paper Out LED and Online LED will blink twice simultaneously which indicates that the printer enters the setup menu system e The title and main menu are printed out firstly as the following figure shown the default settings are underlined Print head stays under the current default item jolinark DP350 SETUP MENU SYSTEM Use the LOAD EJECT key to point the print head to the desired setting Use the LF FF key to confirm the current setting Use the ONLINE key to go back the previous menu Press and hold the ONLINE key to go back the main menu Press and hold the TEAR key to save settings and exit Current settings are E LI E New settings will be FILLED IAIN ME CHARACTER PAGE LAYOUT SYSTEM SETUP SERIALI F M PIN TEST Figure 3 14 Setup menu system 2 Using the following keys to modify th
25. allel cable connector securely into the printer s parallel interface Squeeze the wire clips together until they lock in place on either side of the connector Shown as figure 1 13 Parallel interface Parallel cable Figure 1 13 connect to the parallel interface 2 Plug the other end of the cable into the computer s parallel interface and make sure it is connected fast 1 8 2 Connecting to the USB Interface 1 Plug the USB cable A end flat shape into the computer s USB interface 2 Plug the USB cable B end square shape into the printer s USB interface Note Don t impact the plug after connecting to the USB cable USB cable 8 Figure 1 14 connect to USB cable DP350 User s Manual 1 8 3 Connecting to the Serial Interface 1 Turn off both the computer and the printer Plug the serial cable connector securely into the printer s serial interface Tighten the screws on either side of the connector Serial cable y ppo Serial interface Figure 1 15 connect to serial interface 2 Plug the other end of the cable into the computer s serial interface then tighten the screws on either side of the connector 1 8 4 Connecting to the Ethernet Interface Plug the RJ 45 crystal end of the Ethernet cable into the printer and plug the other end into the LAN Shown as figure 1 16 Ethernet cable Ethernet interface Figure 1 16 connect to the Ethernet interface Note The details of Ethernet interface prin
26. an be used when transport the printer 1 3 Main Parts of the Printer Figure1 2 and figure1 3 shown are main parts of DP350 Gap adjust lever Printer upper cover Ribbon cartridge Paper feed knob Control panel Figure1 2 main parts of the printer front view DP350 User s Manual Paper guide slide Printer back cover Paper feed knob Tractor P itch Serial interface ower switc Parallel interface Power supply inlet Ethernet interface USB interface USB interface Figuer 1 3 main parts of the printer rear view According to specific interface standards 1 4 Choosing a Place for the Printer When selecting a place to set up your printer choose a convenient location that provides the following 1 A flat stable surface 2 Adequate room around the printer to allow easy operation and maintenance Make sure it s close enough to the computer for the printer cable to reach and be sure you can easily unplug the power cord 3 Moderate environmental conditions Select a cool dry area and protect your printer from direct sunlight excessive heat moisture or dusty 4 Appropriate power source Make sure you use a grounded outlet do not use an adapter plug Avoid electrical outlets controlled by timers or wall switches an interruption in power can wipe out the information in your computer or printer memory If you place the printer on a stand follow these guidelines 1 Use a st
27. and that supports at least 9 kg 19 Ib 2 Never use a stand which is slant Always keep it level 3 Provide enough clearance below the stand and between the printer rack and the legs of the rack so the tractor paper flows smoothly 4 Place cables so they do not interfere with paper feeding secure them to a leg of the stand if possible 1 5 Installing the Ribbon Cartridge 1 Before installing the ribbon cartridge make sure the printer is turned off 2 Open the printer upper cover Printer upper cover Print head Figure 1 4 open the upper cover 2 DP350 User s Manual 3 Put the gap adjust lever to the uppermost position 4 Slide the print head to the middle of the printer shown as figure 1 4 Note Never move the print head while the printer is turned on this can damage the printer Also if you have just used the printer let the print head cool for a few minutes before you touch it 5 Please push out the ribbon nip according to the label on the ribbon cartridge Ribbon cartridge JMR120 Ribbon tighten knob Ribbon core Ribbon nip Figure 1 5 ribbon cartridge 6 Hold both sides of the ribbon down firmly to fit the plastic hooks into the printer slots Then put the ribbon nip between print head and ribbon guide slice Press it down until it click into place shown as figure 1 6 Ribbon tighten knob Ribbon nip Ribbon guide slice Print head Figure 1 6 install ri
28. apers your printer can also print on a wide variety of paper types including multi part forms labels and envelopes Caution When printing on multi part forms as it is thicker than the general paper it needs the bigger print force printing past or at the edge of these papers can damage the print head Please make sure the printing contents are all within the printable area while printing The correlative printable area see the Appendix A for reference 3 1 1 Loading Cut Sheets 1 Make sure the printer is powered off and open the upper cover of the printer select the correct gap of the printer thought the gap adjust lever as shown in the illustration on chapter 2 7 Figure 3 1 adjust the gap adjust lever 2 Close the cover and set paper select lever toward the cut sheet position Figure 3 2 adjust the paper select lever 3 Raise the printer back cover to the proper position shown as figure 3 3 and turn on the printer 24 DP350 User s Manual Back cover Figure 3 3 adjust the position of the back cover 4 Adjust the right paper guide of the back cover to the range of the scale Then adjust the left paper guide to make the distance match the width of the print paper Shown as below Figure 3 4 adjust the right and the left paper guide 5 Slide a piece of cut sheet down firmly between the right and left paper guides until it meets resistance The printer loads the sheet automatically shown as below
29. aseeneeeesaseeeeeaseaneeeaseanes i HXcpIa ii leurgcmlAdccrinp 1 1 1 Unpacking and Checking norisi arie eaa aa Er ern AAAA ONE ener nennen nenne EAEAN Aaa dE 1 1 2 Dismantling the Protective Materials sssssee Heer 1 1 3 Main Parts of the Printer uoce roce deest A E Uta dog ee eer deed Ane Hy 1 1 4 Choosing a Place for the Printer ccccccccecceeeneeceeeeeee see caeeeeeeeeeesecceeseeeeeeesececneeaeeeeeeeessnsaseeteeeess 2 1 5 Installing the Ribbon Cartridge ssssssssssssseneeeenenenmne e eren nn nennen rennen nnne nnn nnne 2 1 6 Connect the Power Cord sssssssssssssseseseseeeeeee nn nn cnn enne R RR nn nn eren nennt rennen nene n en nnn nnns nennen 4 1 7 Printer Self test FUNCION ainia eric entente acia 4 1 8 Connecting the Printer to Your COMputeT oooococccionoccccccononccncnnoncnccnnncnccnonnnncn nono n cnn conan nn enne nnne 5 1 8 1 Connecting to the Parallel Interface eese eene nnne nennen nnn nnne 6 1 8 2 Connecting to the USB Interface isses eene nnne nnn nnne nennen nennen nnn nn 6 1 8 3 Connecting to the Serial Interface ooonmoiicinnonicccnnnneccccnnnonccnnnnannccncnnn nc n enhn 7 1 8 4 Connecting to the Ethernet Interface essssssssssse esee en 7 1 9 Installing Printer Driver a ERREUR e Ree Re dee TERR RR NU ear t dees 7 1 1
30. bbon cartridge 7 Turn the ribbon tighten knob in the direction of the arrow to remove any slack from the ribbon so it is easier to install 8 Slide the print head from side to side several times to make sure it moves smoothly 9 Please put the gap adjust lever to original place and close the upper cover after the ribbon cartridge is installed NOTE 1 When your printing becomes faint you need to replace the ribbon cartridge Otherwise the print quality will be affected and the print head may be damaged 2 To remove the old ribbon cartridge first make sure the power is turned off move the print head to the center of the printer Then grasp the ribbon cartridge handle on either side and lift it out of the printer m DP350 User s Manual 3 Please use the Jolimark JMR120 ribbon cartridge our company will not guarantee to keep the printer in good repair when it is damaged by unauthorized ribbon cartridge 1 6 Connect the Power Cord 1 Make sure the power switch on the printer is turned off lt is off when the O side of the switch is pressed down 2 Make sure the voltage required by the printer matches that of your electrical outlet 3 If the power cord is attached to the printer connect it to the AC inlet on the printer 4 Plug the power cord into a properly grounded electrical outlet Power switch Figure 1 7 turn off the printer Caution 1 If the rated voltage and your outlet voltage do not match contact yo
31. ce ccccce cesses eseeeeeeeeeeeneeeeeeseeeeensseeeseaeseneeeesasnaeeeeaseaneeeeseseeeeesssueeenesnenseaes 39 Appendix A Specifications ceeeeccseeeeeeseeeneeeeeeeeeeeenseeneeenseeneeeesaseeeeeeneseneseseqeneeeeasseneeeaseeseeeeseneneeensanees 40 AT General itte epa to P se Hiero aa Potente itd eben oed edd tat eed ed De uter rest Ig e Po dee eeu 40 A2 Interface SpeclifICatloris nien iei epar iie e eret id pep Een Le EE rum i DRE dea cane adaa aa aaa Esei 42 A 2 1 Parallel Interface ie etn Idoia STRE RAE KATE RTI RET RR 42 A 2 2 USB Interface o i a d e a a e ee Me seus 42 A 2 3 Serial Interface pa t a ut d Ra eL d UE RE ee i ie Lr aa 42 A24 Ethernet Interface te e EE DER D ror DEP ERU Pei eaa ee 43 Az3 Printable AAA oda 43 Appendix B Command Summary cocccccncoccccnninnnncninanonc cnn 45 DP350 User s Manual Chapter 1 Preparation 1 1 Unpacking and Checking Check the following items in the packing box if any of these items are missing please contact your dealer E F Figure1 1 Unpacking list A Printer B Ribbon cartridge JMR120 C Power cord D Driver CD Including user s manual and driver E Packing list F Facility user s guide Caution The fittings please refer the packing list The packing style above is subject to change without notice 1 2 Dismantling the Protective Materials 1 Open the packing box lift up the printer 2 Save all the original packing materials so that it c
32. contents are within the printable area 2 If the print contents exceed the printable area the print head may be damaged Cut Sheets A The minimum top margin 8 0 mm B The minimum right left margin is 3 0 mm However the maximum printable width is 203 2 mm 8 0 inches C The minimum bottom margin 2 9 0 mm 0 35 inch 43 DP350 User s Manual Tractor paper A The minimum top and bottom margin above and below the perforation are gt 8 0mm B The minimum left and right margins are gt 13 0 mm The maximum printable width is 203 2 mm 8 0 inches 44 DP350 User s Manual Appendix B Command Summary This printer supports EPSON ESC P K2 control commands shown as the follow table Classify No Command Description 1 ESC Initialize Printer 2 CAN Cancel Line 3 DC1 Select Printer 4 DC3 Deselect Printer 5 DEL Delete Character 6 ESC Cancel MSB Control Sequence 7 ESC gt Set MSB to 1 8 ESC Reset MSB to 0 9 BEL Beeper 10 BS Backspace 11 ESC U Select Print Direction Printer 12 ESC lt Select character Unidirectional Mode on one line control 13 ESC s n Select Cancel Quiet Print Mode commands 14 CR Carriage Return 15 LF Line Feed 16 FF Form Feed 17 ESC Set Absolute Horizontal print position 18 ESC Set Relative Horizontal print position 19 ESC U Define Unit 20 ESC V Set Absolute Vertical Print
33. e menu setting LOAD EJECT Select the menu option or menu setting value LF FF Enter into submenu or confirm menu setting value Note Newly setting option will be shown in FILLED ONLINE Return to upper menu Hold on pressing ONLINE key will return to main menu directly TEAR Save and exit the setup menu system 3 Give up the settings just modified just turn off the printer directly If you need to save the newly setting hold on pressing TEAR key to save and exit the menu setting mode 4 Turn off and restart the printer newly settings are in operation 3 2 2 Online aptitude Parameter Settings DP350 supports the function of online aptitude parameter settings which can be set in the PC with the driver installed in The concrete setting steps are shown as follows 1 Make sure that the host and the printer are connected with a cable and both the host and the printer is turned on the printer should be online as well 2 Click Start Settings Printers 3 Right click Jolimark DP350 in the Printers select Properties 4 Click Device Property in the property page 31 DP350 User s Manual Jolimark DP350 Properties ax General Sharing Ports Advanced Security Device Settings Printer Settings Printer Setting Menu Select Printer Setting Class CHARACTER Reset All Options Select font type Default ROMAN Font pitch Chinese font pitch
34. g assignments by number and color for Series A and Series B connectors of Full speed USB 2 0 Contact Number Signal Name Color 1 VBUS Red 2 D White 3 D Green 4 GND Black Figure A 2 USB B type connector A 2 3 Serial Interface The serial interface has the following characteristics Baudrate bps 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps selectable Word length 7 or 8 bit selectable Start bit 1 bit Parity bit Odd even or none selectable Stop bit 1 bit Handshaking DTR protocol X ON X OFF protocol selectable Serial pin assignments The following table lists the serial connector pin assignments and describes their respective interface signals 42 DP350 User s Manual Pin No Signal Direction Description 1 Frame Ground FG Printer s chassis ground 2 Transmitted Data TXD SD Out Printer has transmitted serial data 3 Received Data RXD RD In Printer has received serial data 7 Signal Ground SG Return path for data control signals 20 Data Terminal Ready DIR out _ Poste shen he pinter s ready to receive data 13 1 0000000000000 O rere O 25 14 Figure A 3 Serial interface connector pin number A 2 4 Ethernet Interface 10 100Base T Ethernet interface can connect to 10 100M Ethernet Figure A 4 Ethernet interface A 3 Printable Area Note 1 To assure the print quality please make sure the print
35. haracter 50 FS DC2 Cancel half size mode for Chinese character 51 FS r Select demisemi size mode for Chinese character 52 FS Select Chinese character print mode 53 FS y Select Cancel form connect line 54 FS k Select Chinese font 55 FS Y Select Chinese character dot matrix and width 56 FS c Set Chinese character HMI Horizontal motion space 57 FS b Set Chinese character datum line 58 ESC Select Chinese CC DOS print mode 59 ESC k Select Font Style 60 ESC X Select ASC II character width and height 61 ESC P Select 10CPI Mode 62 ESC M Select 12CPI Mode eta 63 ESC g Select 15CPI Mode 64 ESC p Select Cancel Proportional Mode 65 ESC x Select Print Quality 66 ESC 4 Select Italic Mode 67 ESC 5 Cancel Italic Mode 68 ESC E Select Emphasized Mode 69 ESC F Cancel Emphasized Mode 70 ESC n Select Print Mode 71 ESC q n Select Character Style 72 ESC t n Select Character Table 73 ESC t Assign Character Table 74 ESC R Select International Character Set 46 DP350 User s Manual 75 ESC amp Define Downloaded Characters 76 ESC Copy ROM Characters Set into RAM 17 ESC n Select Deselect User Defined Set 78 ESC 6 Enable Character Set 2 79 ESC 7 Cancel command ESC 6 80 Sl Select Compressed Mode 81 DC2 Cancel Compressed Mode 82 SO Select Double Width Mode 83 DC4 Cancel Double Width Mode 84 ESC W n Select Cancel Double Width M
36. inter takes response after Close this window on success is checked and then this dialog is closed automatically Select Reload Timer then the software will wait for the printer s response Generally printer will take response in a circle time if network connection is correct Click Cancel if you abandon the modification Click Search in the main interface again to update printer information after modifying the printer s IP address 3 Report printer s IP address Report the printer s IP address which will be used in the section Newly install printer network driver or Upgrade install printer network driver setting driver s network port 1 10 3 Installing Printer Network Driver The ways of installing network driver are divided into Newly install way and Upgrade install way according to whether the PC installs the printer driver or not If the printer driver hasn t been installed on the PC adopt newly install way whose steps are shown in Newly install printer network driver 12 DP350 User s Manual If the printer driver has been installed on the PC adopt Upgrade install way whose steps are shown in Upgrade install printer network driver 1 Newly install printer network driver 1 Click Start Settings select Printers 2 Click Add printer then come out a window of Add Printer Wizard click next 3 Come out a window of Add Printer Wizard then please read
37. k Next and then show the printer s name If the system is not installed by other printer driver process the printer is treated as default printer by the application process of Window98 8 DP350 User s Manual environment click Next Otherwise according to prompt choose the printer is default Yes click Next choose Yes recommended click Finish Come out a window of Printer test page completed click Yes 6 The printer driver process is installed successfully 2 The installing steps with an USB cable Note 1 As the system of Windows 98 ME doesn t have integrated USB drive control please install USB drive before using USB interface printing Then install USB printer drive 2 If it has installed the USB drive please install the USB printer drive directly as the following steps The installing steps of USB driver 1 Connect an USB cable and turn on the printer 2 After the computer find out new hardware and finish searching come out a window of Add New Hardware Wizard click Next 3 Come out a window of Add New Hardware Wizard Windows operation choose Search the best driver for the device recommended click Next 4 Come out a window of Search for new drivers check Specify a location click Browse select the path as follows CD ROM Driver WIN98 WINME USBdriver then click OK 5 Return to a window of Search for new drivers click Next Come out a window
38. limark printers which can be found in the CD or downloaded from www jolimark com Note The network printing function needs the operation system of Windows2000 or above 1 10 1 Connecting Printer Power on the printer connect with the Ethernet cable which has been connected to LAN and look into the information of Ethernet LED indicator to ensure the printer has entered into the normal connection DP350 User s Manual Yellow LED Green LED Description ON Blink Normal OFF OFF Not connect to network 1 10 2 Setting IP Address 1 Run NetFinder Software Double click NetFinder exe in the PC which connects the printer in the same LAN The figure of the software is shown as follows Netrinder Exit Search Assign IP Button description Exit Exit from the software Search Search printers in the same LAN Assign IP Modify the IP address and other settings for the specified printer 2 Search printer Click Search button in the main interface the dialog box appearing will begin searching automatically and show appearance listing a printer in the main interface if found The time is counting down in the progress bar 10s in total and the search will finish as soon as the time is over When going on searching press search button again 10 DP350 User s Manual NETPTHUET time left 8 second s found 1 device s Reload Timer IV Close this window when searching completes
39. lutions The ribbon may be worn out Replace the ribbon as described on chapter 1 5 e Dots are missing in printed characters or graphics Phenomenon 1 A line of dots is missing in the printout Solutions The print head may be damaged Stop printing and contact your dealer or a specified Jolimark service center to have the print head replaced Phenomenon 2 Dots are missing in random positions Solutions The ribbon may be damaged Replace a new one e Printed characters are not what you expected Phenomenon 1 The fonts or characters you sent with your software did not print Solutions Check whether the driver is correctly configured for your printer For instructions see chapter 1 9 Phenomenon 2 The font selected on the control panel can not be printed Solutions Your software may be overriding your control panel setting Use the font setting in your software program e The print position is not what you expected Phenomenon 1 The original print position is not correct or the bottom part of one page is printed at the top of the next page Solutions 1 It is also possible to adjust the top of form position using the micro adjust mode To use micro adjust mode see Micro Adjust on chapter 2 4 4 2 Check the page length set by your software and adjust it in the software or in the printer to match the paper length Phenomenon 2 Regular gaps occur in the printout Solutions Page skip function may be on Set page skip fu
40. m ASCII Chinese Speed 10 CPI 12 CPI Speed 6 7 CPI 7 5 CPI Print speed Super high speed 400 CPS 480 CPS Super high speed 201 CPS 225CPS High speed 300 CPS 360 CPS High speed 134 CPS 150CPS Normal speed 150 CPS 180 CPS Normal speed 100 CPS 112 CPS Brnthsad Diameter zi wire 0 22 du Life 500 million dots wire Resolution 360 x 180 dpi Max Character set ASC Il 17 international character sets American France Germany English Denmark Sweden Italy Spain Japan Norway Denmark II Spain II Latin America Korea LEGAL Holland Turkey Chinese GB 18030 Chinese character sets 28 variety U S A MULTI PORTUGAL CANADA NORWAY EAST EURO CYRILLIC RUSSIAN HUNGARY KAMENICKY TURKEY ICELAND BULGARIA Code MAZOVIA GRK 437 GRK 851 GRK8859 7 GRK 1253 ARAB NLS ARAB EXT WIN LAT1 WIN LAT2 ISL LTN1 ISO LTN2 TUR8859 9 ISO LTNQ KBL LATIN 7 ae i ASCII Draft Roman Sans Serif Courier Prestige Script OCR B OCR A Orator onts se Chinese GB18030 Song Ti Bar code EAN 13 bar code EAN 8 bar code Interleaved 2 of 5 matrix25 bar code industry25 bar code 39 bar code 128 bar code B 128 bar code C NW 7 bar code f ASCII 10 CPI 12 CPI 15 CPI proportional Ch t tch HEU A Chinese 6 7 CPI 7 5 CPI Line space 1 6 inch 1 8 inch programmable in 1 360 inch increments f Normal mode 3 6 inches per second Continuous feed Maximum 60ms form feed one li
41. ment Automatic function Emulation Match Online Parameter Setting Physical dimensions 384 width x 280 depth x 139 height mm Weight Approx 6Kg Environmental Temperature 5 35 C Operating environment Humidity 40 RH 80 RH No condensation conditions Temperature 40 55 C Storage environment Humidity lt 93 RH 40 C No condensation Rated voltage 110V 176 242V Power Note Please refer to the nameplate label on the printer for detailed voltage requirements specification Rated frequency range 50Hz 60Hz Operation 53 W 2Max 236 W Standby 2 9 W iHe Note eae the produce doesn t connect power supply could consume zero Reliability MTBF220 000 hours IEC 605 7 standard Safety marks EN60950 EMI B class 41 DP350 User s Manual A 2 Interface Specifications Your printer is equipped with a parallel interface two USB interfaces and an option among a serial interface or Ethernet interface The printer switches automatically to the appropriate interface when it receives data A 2 1 Parallel Interface The parallel interface has the following characteristics Data format 8 bit Synchronization STROBE pulse Handshaking BUSY and ACKNLG signals Signal level TTL compatible Figure A 1 Parallel interface connector pin number A 2 2 USB Interface The following table provides the standardized contact terminatin
42. n 3 4 Restore the Default Settings 1 Hold on TEAR LOAD EJECT and LF FF keys on the control panel at the same time and then turn on the printer The LEDs of the PAPER OUT and ONLINE on the control panel blink 3 times respectively at the same time and the printer makes two beeps to confirm that the printer s factory settings have been restored 2 Loosen the keys and switch the printer off and on again 3 After these steps the printer s factory settings work Note After restore all the factory default settings The network setting parameters resume default value at the same time 34 DP350 User s Manual Chapter 4 Troubleshooting Most problems you may encounter while operating your printer herein have simple solutions for those problems You can check the operation of your printer using the self test See Running the Self Test on chapter 1 7 If the self test works properly the problem probably lies in the computer the software or the interface cable If the self test does not work contact your dealer or qualified service person for assistance Note Press LOAD EJECT while turning on the printer you can run the Chinese self test Press TEAR while turning on the printer you can run the English self test Note If you are an experienced user or a programmer you can print a hexadecimal dump to isolate communication problems between the printer and computer To print a hex dump turn off the printer Next hold d
43. n and the printer enters into the print mode Press this key in the online mode the printer is offline ONLINE indicator blinks and the printer can not print 2 If the paper is at the tear position in the offline mode press ONLINE button the printer will go back to the printing home position of current page or the next page 2 4 2 In the Cut Sheet Mode LF FF If the paper is at the print position in the offline mode press the LF FF button once less than 0 5 second the printer will feed the paper one line base on current line spacing setting Alternatively hold the LF FF button down the printer will eject the paper until the cut sheet is entirely ejected LOAD EJECT If the paper is at the print position in the offline mode press the LOAD EJECT button the paper will be entirely ejected from the printer ONLINE If the printer has loaded paper in the offline mode press the key to enter ONLINE mode the ONLINE indicator is on and the printer enters into the print mode Press this key in the online mode the printer is offline ONLINE indicator blinks and the printer can not print 2 4 3 Print Speed the setting method of the print speed In offline mode press the SPEED button to switch the print mode among Normal Speed mode High Speed mode and Super High Speed mode The green indicator denotes normal speed mode the yellow one denotes the high speed mode and the red one denotes the super high speed mode 2 4 4 Micro Adjust of the P
44. nction to off in the Printer Setting mode See 36 DP350 User s Manual Changing the printer settings on chapter 3 2 4 3 Paper Handling e Cut sheets do not be fed properly Phenomenon 1 Paper does not feed Solutions 1 Tractor paper may be left in the printer Remove the tractor paper Set the paper select lever to the cut sheet position Insert a new sheet 2 Maybe the sensor can not check there is paper if there is no tractor paper in the printer and the paper select lever is in the proper position Try to move the paper a little left to make sure to touch the paper in sensor Phenomenon 2 Paper feeding is skew or the paper jammed Solutions Turn off the printer and pull out the jammed paper Reinsert a piece of cut sheet straight into the paper guide and adjust the paper guide to match with paper width Make sure that the printer upper cover is closed and power on again Phenomenon 3 Paper does not eject completely Solutions 1 Press the LF FF button to eject the page 2 Make sure the printer upper cover is closed 3 The paper may be too long Check whether the paper used meets the specifications specified in the Appendix and the using paper must be within the specified range See the paper specifications in the Appendix e Tractor paper does not feed properly Phenomenon 1 The tractor does not feed the paper Solutions 1 Check that the paper select lever is pulled forward to the tractor paper position
45. ne 1 6 inch paper feed speed Copy mode 3 inches per second Continuous feed 68ms form feed one line 1 6 inch Emulation EPSON ESC P K2 IBM2391 Parallel Interface Centronics IEEE1284 NIBBLE USB Interface 2 0 Full Speed Interface Serial Interface RS 232C Internet Interface 10 100Base T A According to specific interface standards Buffer Input 132 KB M Ribbon eas Mey Life 10 million characters draft mode Noise lt 53 dB A ISO7779 standard Control panel 5 keys 3 indicators Paper type feed Cut sheet feed paper by friction Tractor paper feed paper by the tractor 40 DP350 User s Manual don M Set through paper gap adjust lever Width 48 261 mm Cut sheet feed by tractor Thickness 0 065 0 14 mm Weight 52 90 g m Width 56 267 mm Continuous paper feed from Thickness 0 065 0 39 mm Paper rear to front Weight single paper 52 82 g m specification Multiple paper every page 40 58 g m Width mount 101 6 254 mm Least label 63 5 mm x 23 8 mm Label Thickness mount 0 07 0 09 mm Total thickness 0 16 0 19 mm Weight 68 g m Max aper Miss eran Copy Original 4 copes Auto function Optional Paper edge detect Black mark detect Compress set Support graph and character compress printing Special Automatic Pin Break Compensation Automatic Pin Rotation Replace
46. nt adjust mode Note Alignment adjust mode will affect the printing quality think over before adjust it and strict to the instructions while adjusting 38 DP350 User s Manual Chapter 5 Printer maintenance Carriage shaft Figure 5 1 Printer cleaning Periodical cleaning and cleaning tool Periodical cleaning Every 6 months or 300 working hours Cleaning tool Dry cloth Use soft cloth while cleaning metal Cleaning carriage shaft There is a layer of oil covered on the carriage shaft which guarantees the carriage runs smoothly But the oil is easy to absorb dust please clean the dust with soft cloth first and then add proper lube NYE180 lube of NYE Company is recommended move print head back and forth to make lube scattered Cleaning the form feed path Wipe off wastepaper clean dirt and dust Note 1 Turn off printer and pull out the power cord before cleaning 2 Being used under dust circumstance the carriage shaft may stack much dust and affect the print quality 3 If you have just finished using the printer let the print head cool for a few minutes before you touch it 4 Please use a soft cloth for cleaning do not use combustible solvent 39 DP350 User s Manual Appendix A Specifications A 1 General ITEM DESCRIPTION Print Type 24 pin Dot Matrix Impact Printer Print direction Bidirectional logic seeking Print width 80 columns 10cpi 203 2 m
47. ode 85 ESC w n Select Cancel Double height Mode UU NEN LCS Select Double Strike Mode 87 ESC H Cancel Double Strike Mode 88 ESC n Select Cancel Underline Mode 89 ESC Define and Apply a Style of Scoring 90 ESC Print Data as Characters 91 ESC S n Select Superscript Subscript Mode 92 ESC T Cancel Superscript Subscript Mode 93 ESC C Set Form Length in Lines 94 ESC C NUL Set Form Length in Inches 95 ESC C Set Form Length in Defined Unit 96 ESC c Define Form Format 97 ESC N n Select Skip Over Perforation 98 ESC O Cancel Skip Over Perforation 99 ESC Set Left Margin 100 ESC Q Set right Margin 101 ESC D Set Horizontal Tab Positions Format 102 ESC B Set Vertical Tab Positions control 103 ESC Select a VFU Channel 104 ESC b Select VFU Positions 105 ESC 0 Select 1 8 inch Line Spacing 106 ESC 2 Select 1 6 inch Line Spacing 107 ESC 3 Select n 180 inch Line Spacing 108 ESC A Select n 60 inch Line Spacing 109 ESC Select n 360 inch Line Spacing 110 ESC SP Set Character Space 111 ESC fe 2 Select Justification Mode 47 jyolmark
48. of Windows driver file search for the device click Next 6 After the system finishes installing the file automatically come out a window of USB print supported click Finish 7 The printer USB driver process is installed successfully The installing steps of USB printer driver 1 Click Start Settings Printers 2 Click Add Printer then it will show a window of Add Printer Wizard click Next 3 Come out a window of Click the manufacturer and model of your printer click Have Disk please click Browse select the path as follow CD ROM Driver WIN98 WINME where you can find a file named DP350 inf click Open and then click OK 4 Come out a window of Install From Disk click OK return to a window of Add Printer then click Next 5 Come out a window of Printer port select Available ports select JMUSB click Next and then show the printer s name If the system is not installed by other printer driver process the printer is treated as default printer by the application process of Window98 environment click Next Otherwise according to prompt choose the printer is default Yes click Next choose Yes recommended click Finish Come out a window of Printer test page completed click Yes 6 The printer driver process is installed successfully 1 10 Network Settings Please use Jolimark network setting software NetFinder to set the IP address for Jo
49. ollow the direct click Next gradually till the installation is finished The installing steps for Windows 7 with parallel cable are as follows 1 Click Start Devices and Printers 2 Click Add a printer then it will show a window of Add Printer click Add a local printer and then click Next 3 Come out a window of Choose a printer port select Use an existing port such as select LPT1 Printer Port click Next 4 Come out a window of Manufacturers Printers click Have Disk 5 Come out a window of Install From Disk Please according to the operating system environment should select the path as follow CD ROM Driver WIN2000 XP Vista Win7 where you can find a file named DP350 inf click Open then click OK to return to the window of Manufacturers Printers click Next 6 Follow the direct click Next gradually till the installation is finished The USB interface installing steps for Windows 2000 XP Vista Win7 are as follows The following steps are used Windows XP as example There are slight differences among different operating systems 1 Connect an USB cable and turn on the printer 2 After the computer find out new hardware and finish searching come out a window of Found New Hardware Wizard choose Install from a list or specific location Advanced click Next 3 Come out a window of Add New Hardware Wizard Windows operation choose Don t search will cho
50. ose the driver to install D click Next 4 Come out a window of Hardware Type select Printer click Next Come out a window of Manufacturers Printers click Have Disk 5 Come out a window of Install From Disk Please according to the operating system environment you should select the path as follow CD ROM Driver WIN2000 XP Vista Win7 where you can find a file named DP350 inf click Open then click OK to return to the window of Add printer wizard click Next 6 Follow the direct click Next gradually till the installation is finished The installing steps for Windows 98 are as follows 1 The installing steps with a parallel cable or a serial cable 1 Click Start Settings Printers 2 Click Add Printer then it will show a window of Add Printer Wizard click Next then please read the select direct carefully Such as select Local printer in the Local or Network Printer window then click Next 3 Come out a window of Click the manufacturer and model of your printer click Have Disk please click Browse select the path as follow CD ROM Driver WIN98 W INME where you can find a file named DP350 inf click Open and then click OK 4 Come out a window of Install From Disk click OK return to a window of Add Printer then click Next 5 Come out a window of Printer port select Available ports such as select LPT1 Printer Port clic
51. ou can set the page length to 3 3 5 11 3 4 5 5 5 6 7 8 5 11 12 or 70 6 the length of A4 paper inches 6 FORM LOCK Select form lock function ON or OFF 7 PAGE SKIP When you turn on this feature the printer skips over the perforations of tractor paper providing a 1 inch margin between the last line printed on one page and the first line printed on the next 8 COMPRESS PRINT Select compressed print proportion 9 LANGUAGE Select the language in the menu The printer will print with the selected language according to the menu setting 10 EMULATION Select the emulation of EPSON ESC P K2 or IBM 2391 11 HIGH DENSITY Open or close the high quality printing 12 PRINT DIR You can choose unidirectional bidirectional or auto as the print direction for graphics When the default item is auto the printer prints characters bidirectionally while prints graphics unidirectionally The print direction command is effect If auto is set the command controlling the print direction is priority Otherwise either unidirectional or bidirectional is set it prints both characters and graphics bidirectionally or unidirectionally the command is of no effect 13 CHAR MODE Select the ASCII or Chinese character mode 14 INTL CHAR SET Select interior character only with EPSON compatible U S A FRANCE GERMANY U K DENMARK 1 SWEDEN ITALY SPAIN 1 JAPAN NORWAY DENMRK2 SPAIN 2 LATIN AN KOREA LEGAL HOLAND TURKEY 15 CHARACTE
52. own the LF FF and TEAR buttons while you turn on the printer Then send data from your computer The printer prints all the codes it receives in hexadecimal format 4 1 Power Supply Power is not being supplied normally Phenomenon 1 The lights on the control panel do not go on and the printer has no action Solutions 1 Check that the power cord is properly plugged into the electrical outlet 2 If the electrical outlet is controlled by an outside switch or automatic timer use another outlet 3 Plug another electrical device such as a lamp into the outlet to determine whether the outlet is operating properly Phenomenon 2 The lights come on briefly and then go off The lights stay off even when the power is turned on again Solutions Check whether the printer s rating voltage is matched with the power cord If not unplug the power cord immediately and contact your dealer or a specified Jolimark service center for advice Do not plug the power cord to the electrical outlet again 4 2 Printing Problem The printer does not print Phenomenon 1 The Online light is on but nothing is printed Solutions 1 Check that the Driver is installed properly for your printer as described on chapter 1 9 Check the driver s printer settings 2 Check both ends of the interface cable Make sure the cable meets both the printer and computer specifications Phenomenon 2 The Online light and paper out light blink the printer beeps once
53. pes only under normal temperature and humidity conditions 4 Make sure the printing stays entirely within the printable area The print head must not go past the left or right edge of the envelope or other thick paper See the Appendix for specifications It s a good idea to print a test sample using a normal single sheet of paper before you print on the envelopes 28 DP350 User s Manual 3 2 Changing the Printer Settings 3 2 1 Setting printer parameter through the control panel 1 Press the ONLINE button on the control panel as well as turn on the printer The print head returns with the printer beeping once If the ONLINE indicator and the Paper Out indicator blink it can be indicated that there is paper out 2 Set the paper select lever to the proper position If in cut sheet mode the paper select lever should in the cut sheet position otherwise it should in the tractor paper mode 3 After loading paper in cut sheet mode the printer will print out the current setting automatically In tractor mode after install the paper to the tractor paper once you press LOAD EJECT button the printer starts printing the current setting 29 DP350 User s Manual Jolinark DP350 Current Setting Report Figure 3 13 current menu setting 30 VX X XXX XXXXIXXIXX SN XXXXXXXXXXXXXXXXXXXK MAC Address XX XX XX XX XX XX DHCP YES IP 10 0 0 1 Subnet Mask 255 255 255 0
54. r Port Wizard click Finish 11 Return to Printer Ports click Close Available port types Local Port ThinPrint Print Pork Monitor For VMWare Mew Pork Type Mew Port 12 Return to Properties make sure the network port is selected click Apply and then click Close Thus printer s network port setting is finished 18 DP350 User s Manual amp Jolimark DP350 Properties Serial Port Jolimark TP220 Serial Port Print to File Jolimark TP820 Virtual printer port fo ThinPrint Print Port tfvMwareVirtualPrinter Standard TCP IP Port Jolimark DP350 Enable bidirectional support LI 19 DP350 User s Manual Chapter 2 Control Panel Operations 2 1 Control Panel label Include 5 keys and 3 indicators shown as 2 1 Online SPEED TEAR LF FF LOAD EJECT ONLINE EB Sg 0 r j High Enorma Q Normal 0 Paper Out PAPER OUT ONLINE SPEED y Micro Adjust 4 w 3 Sec Figure 2 1 control panel 2 2 LED Description LED OFF ON BLINK PAPER OUT Normal Paper out or malfunction ONLINE Online Offline SPEED The green indicator denotes normal speed the yellow one denotes the high speed mode and the red one denotes the super high speed mode 2 3 Control Panel Basic Function Description ONLINE Press ONLINE to switch between online and offline LOAD EJECT At the state of paper out press LOAD EJE
55. rinting Home Position and the Tear Position Operation steps of adjusting the printing home position the printing home position of cut sheet is separated with the tractor paper s The following is use tractor paper for example 1 Open the printer Put the paper select lever to the tractor paper mode press LOAD EJECT and install tractor paper 9 DP350 User s Manual 2 Hold the ONLINE button down for 3 seconds ensure the online light blinks till the printer beeps once The online indicator and paper out indicator blinks alternately Caution Don t press SPEED or the printer can t enter the micro adjust function 3 Press LF FF and LOAD EJECT to adjust the printing home position 4 Press the ONLINE button again to save the setting and quit the alternate mode after finishing adjusting The operation step of adjusting the tear position is basically the same with the printing home position s But the exclusive difference is pressing TEAR to feed paper to the tear position after install the tractor paper Caution Don t revolve the paper feed knob when the printer is in the process of the micro adjust Note The adjusted range of original print position is from 18 60 inch to 60 60 inch base on default position set by the factory The adjusted range of tear position is from 15 60 inch to 15 60 inch base on default position set by the factory 2 4 5 Feed Paper to the Tear Position 1 Turn on the printer hold the ONL
56. sition 2 In the offline mode if the paper is at the tear position press TEAR key once and the printer ejects paper to the next page or the printing home position of the current page 20 DP350 User s Manual LF FF In the offline mode if the paper is at the print position press the LF FF button once less than 0 5 second the printer will feed the paper one line base on current line spacing setting Alternatively hold the LF FF button down the printer will load one page of tractor paper LOAD EJECT 1 When the paper is at the ready position press LOAD EJECT once the paper will be fed into the printing home position automatically 2 When the paper is at the printing home position press LOAD EJECT in the offline mode the paper will return the ready position 3 When the paper is at the general print position not the printing home position press LOAD EJECT once in the offline mode less than 0 5 seconds the paper is ejected one line Alternatively hold the LOAD EJECT button down the printer will eject one page of tractor paper if the ejectable page length is more than one page If the paper ejectable length is less than one page the paper will feed back to the ready position 4 When the paper is at the tear position press LOAD EJECT once the printer will eject one page of tractor paper ONLINE 1 If the printer has loaded paper in the offline mode press the key to enter ONLINE mode the ONLINE indicator is o
57. stalling position through LOAD EJECT key on the control panel pull the paper select lever to the cut sheet position Insert the cut sheet from front to print If you want to use tractor paper again pull the paper select lever back to the tractor paper position after cut sheet printing Then press LOAD EJECT key tractor paper may be fed to the printer again e Eject function The function allow the user eject the tractor paper through the facility button on the control panel e Select the data transfer interface function automatically The printer configures with a parallel interface two USB interfaces a serial interface and an Ethernet interface according to specific interface standards Connect the printer to the computer with the correct cables The printer will switch the correct interface according to the type of data automatically e Emulation The printer supports the Epson ESC P K2 emulation as standard e Enhance Chinese Character Set This printer contains GB18030 Chinese character set and also supports 4 bytes Chinese printing e Break pin compensation function User can set the printer to print using the pin which is in good condition to compensate the break pin e Pin switch in turn function User can set pins to switch while printing form transverse line in order to improve print head life DP350 User s Manual Table of contents Important Safety Instructions sssaaa aniano aaan aea enna reci sees eeaeseneeeesseeeeeeassenees
58. ter s net setting please refer to the User s Manual 1 9 Installing Printer Driver Please use the cable to connect computer with printer then turn on the computer and the printer put the drive CD into the CD ROM Install driver by the following way Auto install way Double click the file Setup exe in the driver disc install driver by the following direct Note Auto install just run in the operation system of Windows 2000 or above Hand operated installing way Note The hand operated install ways of serial interface and parallel interface are the same The installing steps for Windows 2000 XP Vista with parallel cable are as follows 1 Click Start Settings select Printers 2 Click Add Printer then it will show a window of Add Printer Wizard click Next then please read the select direct carefully Such as select Local printer in the Local or Network Printer window then click next 3 Come out a window of Select the Printer Port select a usable port Such as select LPT1 printer port click Next DP350 User s Manual 4 Come out a window of Manufacturers Printers click Have Disk 5 Come out a window of Install From Disk Please according to the operating system environment such as Windows XP operating system you should select the path as follow CD ROM Driver WIN2000 XP Vista Win7 that you can find a file named DP350 inf click Open then click OK click Next 6 F
59. this product where the cord will be walked on When the cord or the plug is mangled please stop using and get a new one replaced Make sure the old one is far away from the printer so it can avoid someone who does not know the inside story getting damage Do not use in locations subject to high humidity or dust levels Excessive humidity and dust may cause equipment damage or fire Never push objects of any kind into this product though cabinet slots as they may touch dangerous voltage dots or short out parts Don t remove the printer s out cover and repair the printer When needed call or take it to the professional To ensure safety please unplug this product prior to leaving it unused for an extended period The wall outlet you plan to connect to should be nearby and unobstructed Unplug this product from the power outlet and leave servicing to qualified service personnel under the following conditions A When the power cord or plug is damaged or frayed B If liquid has been spilled into the product C If the product has been exposed to rain or water D If the product does not operate normally when the operating instructions are followed Adjust only those controls that are covered by the operating instructions since importer adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation E If the product has been dropped or the cabinet
60. ulti part forms or it may damage the print 27 DP350 User s Manual head see Appendix for details Figure 3 11 raise the back cover 3 1 4 Labels You basically print on labels as the tractor paper Keep these tips in mind 1 Set the paper select lever to 1 position 2 Make sure the printing stays entirely within the printable area See the Appendix for specifications 3 Because labels are especially sensitive to temperature and humidity use them only under normal operating conditions 4 Do not leave labels loaded in the printer between jobs they curl around the platen and may jam when you resume printing 5 Remove the labels from the printer tear off the fresh supply at the rear of the printer then press LF FF to advance the remaining labels out of the printer Caution Never feed labels in and out through the printer they can easily peel off the backing and jam the printer If a label does become stuck in the printer contact your dealer 3 1 5 Envelopes The method of loading envelopes is basically the same with the cut sheet s Just pay attention to the following tips 1 Before loading an envelope set the gap adjust lever to position 4 or 5 2 Insert the wide edge of the envelope into the printer first printable side down When you insert the envelope between the paper guides push it firmly and hold it until it feeds into the printer Figure 3 12 loading the envelope 3 Use envelo
61. ur dealer for assistance Do not plug in the power cord 2 Adopt the electrical outlet connecting the ground properly 1 7 Printer Self test Function The built in self test function demonstrates that the printer is working properly You can run the test with either tractor paper or cut sheets this section describes the easier way with cut sheets Note You should use paper at least 210 mm 8 3 inches wide to run the self test otherwise the print head prints directly on the platen 1 Make sure the printer is turned off and the paper select lever is pushed back to the cut sheet position Raise the back cover Figure 1 8 set paper select lever 2 While holding down the TEAR button turn on the printer The Paper Out and ONLINE indicator blink which indicates the printer is out of paper 3 Adjust the right paper guide of the back cover to the range of the scale Then adjust the left paper guide to make the distance match the width of the print paper as shown below DP350 User s Manual Figure 1 9 adjust the right and the left paper guide of the back cover 4 Slide a piece of cut sheet down firmly between the right and left paper guides until it meets resistance The printer loads the cut sheet automatically and begins printing when pressing ONLINE button Figure 1 10 install cut sheets Warning Always close the printer cover while the printer is printing 5 To stop printing temporarily press the ONLINE button
62. x If the printer still can not be found out when the network connection is correct and in the same network please check whether the network fire wall on the PC open or not If there is fire wall please close it temporarily open again after finishing searching and setting a printer completely 3 Setting printer s IP address The printer s information is listed in the main interface the left side of which is the model and description and the right is the IP and MAC address What s more the assign mode dynamic static is noted behind the IP address Netrinder Assign IP 1 Correlative description for IP address settings In order to search and set printer s IP address conveniently for the first time the factory default setting is DHCP mode which assigns IP address dynamically If there is no DHCP server in the connected LAN and printer is set to DHCP mode as well then it will use the internal pre set address IP 10 0 0 1 Subnet Mask 255 255 255 0 automatically It is suggested that printer s IP set to static in actual usage which can cut down the time when initializing the Ethernet interface as the printer is turned on and prevent IP conflicts The dynamic afis DP350 User s Manual address used in printer may conflict with another one The network segment part of the IP address and Subnet Mask must be the same as those of PC connecting with a printer For example the address of working PC is 192 168 0 1 255 255 2
Download Pdf Manuals
Related Search
Related Contents
Un autre regard des quartiers Blueframe Web User Manual 5.0 Admiral Craft RG-07 Owner's Manual Copyright © All rights reserved.
Failed to retrieve file