"user manual"
Contents
1. OAOAN OATH ON 0 11 12 Canopy Head Restraint Harness Slots Comfort Pads Chest Clip Harness Straps Buckle Belly Pad Carrier Belt Guides Harness Adjuster Lever under button hole slot User guide stored under cover Harness Adjuster Strap 13 14 15 16 17 18 19 20 21 22 23 24 Low Birth Weight Infant Foam Handle Recline Angle Level Indicator Infant Carrier Release Handle Harness Adjuster Serial Number and Date of Manufacture label Harness Yoke Base Belt Guides LATCH Adjuster Release Button LATCH Adjuster LATCH Connector Storage Slot LATCH Connector 25 26 27 28 29 LATCH Connector Release Button Recline Adjustment Foot Anti Rebound Bar Carrier Attachment Clips Serial Number and Date of Manufacture label on bottom of Infant Carrier Features 17 30 Lock off 31 Recline Adjustment Knob IMPORTANT When not in use this user guide should be stored under the cover base 18 Installing the Base LATCH Installation WARNING e Only raise the base as described in these instructions Do not use anything to raise the base of the infant carrier off of the front edge of the vehicle seat In a crash this could cause the infant carrier not to perform as intended The base must ALWAYS be secured in a vehicle as described on pages 18 31 before attaching the occupied infant carrier to the base Never attach the occupied infant carrier to the base unless the base2. Pull the adjuster strap through the slot in the cover Check that the buckle strap is not twisted and that the red release button faces out Route the lower part of the cover over the child seat Shell 66 Care and Maintenance 9 Fit the plastic flaps under the edge of the child seat shell ci 1 Route the harness straps 1 1 Replace the head restraint cover though the head restraint cover comfort foam and infant carrier shell Be careful not to damage the energy absorbing foam Ensure the slots are aligned in the head restraint cover comfort foam and infant carrier shell 1 SRe attach the harness straps to the harness yoke Ensure the harness straps are not twisted See pages 47 50 for information on which harness strap loops to use Care and Maintenance 67 1 4Before using the infant carrier double check that the harness Straps are not twisted and that the comfort pads chest clip and buckle tongues appear as shown Cleaning the Cover e HAND WASH using cold water and mild soap e LINE DRY to prevent cover from shrinking Cleaning the Shell amp Harness e BRUSH AWAY LOOSE DEBRIS using a soft bristled brush e SPONGE CLEAN using warm water and mild soap e TOWEL DRY 68 Care and Maintenance C Cleaning the Harness Adjuster e BRUSH AWAY LOOSE DEBRIS using a soft bristled brush e SPONGE CLEAN using warm water and mild soap e TOWEL DRY DO NOT Use s
3. Q Installing Your Infant Carrier without Base 37 p Before You Begin v Check that your vehicle seat belt is compatible with infant carrier use See pages 11 15 for more information v Check your vehicle owner s manual to determine how to lock your vehicle belt system v Secure child in carrier before Carrier Installation with Lap installing carrier in vehicle Shoulder Belt a 1 Place the infant carrier rear 2 Pull the vehicle belt out and facing on the vehicle seat route the lap portion of the vehicle belt through the first belt guide Do not route the shoulder portion of the vehicle belt through the belt guides 3 Route the lap part of the 4 Verify that the vehicle belt is vehicle belt through the not twisted and then buckle second belt guide 5 Lock your vehicle seat belt Do not route the shoulder system as instructed by your portion of the vehicle belt vehicle owner s manual through the belt guides See pages 11 15 for more information 6 Push the infant carrier firmly into the vehicle seat while removing all slack from the lap portion and then the shoulder portion of the vehicle belt IMPORTANT f you cannot lock your vehicle seat belt you must use a locking clip See pages 40 43 Locking clips are available for purchase by contacting Britax Consumer Services at 1 888 427 4829 38 Installing Your Infant Carrier without Base Q Installing Your Infant Carrier with
4. rrrnsasvennnnnnnnvennnnnnnnvnnnnnnnnnnnnnnnnnnnnnnnnnnnnenennnnnennnennnnnvnnnnnne 60 Troubleshootng sissie EANAN 71 WY CAINE aars 72 2009 Britax Child Safety Inc All rights reserved P328900_R4 05 09 This product and its components are subject to change without notice 2 General Information Registration Fill out the registration card and mail it in today Child restraints could be recalled for safety reasons You must register this restraint to be reached in a recall Send your name address e mail address if available and the restraint s model number and manufacturing date to Britax Child Safety Inc RO Box 91167 Allentown PA 18109 9925 or call 1 888 4BRITAX or register online at www BritaxUSA com registration For recall information call the US Government s Vehicle Safety Hot line at 1 888 327 4236 TTY 1 800 424 9153 or go to http www NHTSA gov Serial Number Model Number Batch Number Date of Manufacture Service Life of Infant Carrier To prevent injury due to deterioration or hidden damage do not use an infant carrier and base that is older than six years or has been ina severe crash See date of manufacture located on the infant carrier and base O O General Information 3 Certification Motor Vehicle and Aircraft This child seat system conforms to all applicable Federal Motor Vehicle Safety Standards FMVSS 213 This child seat is certified for use in motor vehicles and aircraft
5. Most airlines in the US and Canada will allow the use of a child seat as long as it is labeled as an approved child seat for airline use and fits properly on the aircraft seat Aircraft Travel Contact the airline about their policy prior to traveling The FAA recommends that a child weighing up to 40 pounds use a certified harnessed child seat while traveling on an aircraft Install your child seat in a window seat to avoid blocking the aisle If the aircraft lap belt is too short ask the flight attendant for a belt extender For aircraft installation see Lap Belt Installation instructions without base on pages 44 46 IMPORTANT Do not use the base on aircraft Infant carrier handle must be in any locked position once installed Certified for Aircraft Installation O A WARNING Death or Serious Injury Could Occur e ALWAYS check the back seat upon leaving your vehicle to 4 General Warnings General Warnings 5 A WARNING Death or Serious Injury Could Occur Use only in a rear facing position when using it in the vehicle Use only with children who weigh between 4 and 30 pounds 1 8 and 13 6 kg and whose height is 32 inches 81 3 cm or less Snugly adjust the belts provided with this child restraint around your Child Secure this child restraint with the vehicle s child restraint anchorage system if available or with a vehicle belt Follow all instructions on this child restraint and in the writt
6. 7 Thread the buckle strap retainer that the short side will go through through the slot in the infant the slot in the infant carrier shell carrier shell and cover and cover 52 Securing Your Child Replacing the Buckle 1 Turn the buckle strap retainer 2 Thread the buckle strap so that the short side will go through the slot in the cover and infant carrier shell retainer through the desired Slot in the infant carrier shell and cover to the bottom of the infant carrier shell 3 Pull the buckle away from the amp Check that the buckle strap infant carrier to ensure the is not twisted and that the red buckle strap retainer lies flat release button faces out against the infant carrier shell OO Low Birth Weight Infant Foam Low birth weight foam has been included with this infant carrier for infants weighing 4 to 11 Ibs 1 81 5 kg This foam may be necessary for low birth weight infants to achieve a snug fit of the harness around your child Also see page 6 IMPORTANT Do not use low birth weight foam for infants weighing more than 11 Ibs 5 kg Always use inner buckle strap slot when using low birth weight infant foam see pages 49 50 To use the Low Birth Weight Infant Foam 1 Pull the plastic flaps on the cover Pull the infant carrier cover and foam from the infant carrier shell back to access the buckle slots 3 Slide the foam into place around 4 If the buckle was removed thread the buck
7. Close the lock off plate over the webbing 1 1 Place the infant carrier into the base and press down until a Click is heard Pull up on the carrier handle to confirm attachment OO Installing the Base 21 1 2 Verify that all connections are secure Check that v The LATCH strap is not twisted v The LATCH connectors are properly aligned v The excess LATCH webbing has been secured in the lock off v The infant carrier handle is rotated into any locked position v The infant carrier is secure If the base and infant carrier can be moved more than 1 in 2 5 cm front to back or side to side at the LATCH strap path repeat installation or choose another seating location 1 4 amp The proper recline angle is achieved when the level indicators on the infant carrier are within the level lines 1 S3Check the recline angle IMPORTANT f a correction is required do not turn the recline adjustment knob until tension has been removed from the LATCH strap NOTE t may be necessary to install and uninstall the base more than once to achieve the proper recline angle The vehicle should be parked on a level surface 22 Installing the Base Follow the steps below if adjustment of the recline angle is necessary Press the LATCH adjuster Press the LATCH connector release button to release tension release button and detach the in the LATCH Strap LATCH connectors from the LATCH anchors Connect and tighten th
8. is properly secured in a vehicle Use either the LATCH system or the vehicle belt methods to install this child seat Using both is not approved and may cause the child seat not to perform as intended Before You Begin v Remove the infant carrier before installing the base if attached v Verify that your vehicle is equipped with LATCH anchors If you car does not have LATCH anchors you must use vehicle belt installation methods 1 Open the lock off by lifting the 2 Press the LATCH adjuster tabs and then lifting the lock release button while pulling off plate the LATCH strap to loosen the LATCH connector strap 3 Press and hold the red release button on the LATCH connector while removing the LATCH connectors from the storage slots 5 Attach each LATCH connector to the adjacent vehicle LATCH anchor by pushing them firmly onto the vehicle LATCH anchors until a click is heard Verify that the LATCH connector straps are not twisted Installing the Base 19 4 Position the base in the desired vehicle seating position equipped with LATCH G Pull on the LATCH connectors to verify that the connection is secure 20 Installing the Base 7 Push the base firmly into the amp Route any loose webbing from vehicle seat and then pull the the LATCH adjuster through the LATCH adjuster strap to tighten lock off 1 OPress firmly on the lock off plate and then close both lock off tabs
9. the harness straps is at or below the carrier vg child s shoulders If the harness straps need height adjustment follow the steps below a_Lift the harness height adjuster on the back of the infant carrier Slide the harness height adjuster up or down into the nearest position at or below your child s shoulders The harness height adjuster will lock into place once released NOTE The head restraint and harness strap adjustment is controlled by the harness height adjuster on the back of the infant carrier shell The head restraint will be at the correct height adjustment once the harness straps are correctly positioned for your child OO Harness Strap Adjustment When using the inner buckle strap slot for a child 11 lbs 5 kg or below the inner harness strap loops must be used When using the outer buckle strap slot for a child above 11 Ibs 5 kg the end loops of the harness strap must be used See page 50 Depending on the size of your child you will need to adjust the shoulder straps on the harness to ensure the harness provides the most snug fit around your child A snug strap should not allow any slack It lies in a relatively straight line without sagging It does not press on the child s flesh or push the child s body into an unnatural position To Adjust the Shoulder Straps of the Harness 1 Locate the harness yoke on the back of the infant carrier shell 3 Select the appropriate loop
10. through the belt guides 42 Installing Your Infant Carrier without Base QO 8 Buckle the vehicle belt S Adjust the infant carrier handle The vehicle belt should be tight to any locked position around the infant carrier If it is not tight unbuckle the belt remove the locking clip and repeat steps 2 7 1 OVerify that all connections are secure Check that v The vehicle belt is not twisted v The vehicle belt is tight and locked Ensure that a locking clip has been properly installed v The infant carrier handle is rotated into any locked position v The infant carrier is secure If the infant carrier can be moved more than 1 in 2 5 cm front to back or side to side at the vehicle belt path repeat installation or choose another seating location 1 1 Check the recline angle C Installing Your Infant Carrier without Base 43 1 2 The proper recline angle is achieved when the level indicators on the infant carrier are within the level lines NOTE t may be necessary to install and uninstall the infant carrier more than once to achieve the proper recline angle The vehicle should be parked on a level surface Follow the steps below if adjustment of the recline angle is necessary a Unbuckle the seat belt b Place a rolled towel or pool noodle in the vehicle seat bight See note below Place the infant carrier on the towel or pool noodle to help level the base Repeat the pr
11. Britax Chaperone User Guide C C Contents General TOMTOM susrasa 2 REJSEN EN EN EE a 2 Service Life of Infant CANE Las po paaaiaanenasen 2 Certification Motor Vehicle and Aircraft rrrrnrnnnnnvrnnvvrnnnvnnnvvrrnvvennnvernvversvrernnvernnvernn 3 General W rnings a umnensenasmmeneeniinnsendmsnaoindndenisbbenbinonnnstdade 4 Child Size Height and Weight Limitations rrnnnvvvvvrrnnnnnnnnvnvnvevnnnnnnnnnnveveennnnnnn 6 Vehicle Compatibility eervrrrnnnnnnnvnnvvvrrnnnnnnnnnnvvevennnnnnnnnnvvevenennnnnnnnnvevenennnnnnnnnener 7 uama LATO vpn 7 Connecting the LATCH Connectors ranvvnnvvnnnvennrnrnvernvennvrnnvnnrnrrnnvennrvrnrennnennnnnenenenne 8 Locating and Storing the LATCH Connectors rrrurnvnnnvnnnvvnnvvnnnvnnvvnrnvnrnvennrernrrnrrenennn 9 Vehicle Seating Positions ruravarnvnnnvnnnvrenennnnvnnvvennennnennnnenenennennnennnensnennanensnnennensneene 10 Compatible Vehicle Seat Belts siccsiieideniecnasseccassecsseeweseiaveasas ss sssssisctsezareseensadundeveceianns 11 Incompatible Vehicle Seat Bekts rrrrrrrnnnvrnnvvrrnvvrnnnvennnvrnnrvrnnnvennnvessnvrnnnvesnnvesnnnennnne 15 Infant Carrier POA Wai SS sis sicscecascnssnsazeesecuexteceevestnecenenenciuvaseisueedceuscaxaseuewtparsueennalsveeenesncoess 16 Installing the BASC vecssccceceses seccc dda netisccdacstececesecuseccvescudtces teecuetesnedssesteususteatecenictes 18 EG ans EE ERE 18 Lap Shoulder Belt IMStallatiOn uuanemsememmmeme e
12. NE AT www BritaxUSA com registration WARRANTY LIMITATIONS This warranty does not include damages which arise from negligence misuse or use not in accordance with the product instruction The use of aftermarket covers inserts toys accessories or tightening devices is not approved by Britax Their use could cause this infant carrier to fail Federal Safety Standards or not perform as intended in a crash Their use automatically voids the Britax warranty LIMITATION OF DAMAGES The warranty and remedies as set forth above are exclusive and in lieu of all others oral or written express or implied In no event will Britax or the retailer selling this product be liable for any damages including incidental or consequential damages arising out of the use or inability to use this product LIMITATIONS OF WARRANTIES AND OTHER WARRANTY TERMS AND STATE LAWS Any implied warranties including implied warranties of merchantability and fitness for a particular purpose shall be limited to the duration and terms of the express written warranty Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitations may not apply This warranty gives you specific legal rights and you may have other rights which vary from state to state Neither Britax nor the retailer selling this product authorizes any person to create for it any other warranty obligat
13. R mode or use child seat lock offs with base or a locking clip with carrier only NOTE Refer to your vehicle owner s manual to determine the kind of retractors used in your vehicle and how to operate them 12 Vehicle Compatibility Q Vehicle Compatibility 13 ALR Automatic Locking Retractor with Sliding Latch Plate 2 Has a retractor that locks only in an emergency situation such 1 Hasa latch plate that freely as sudden stop or crash slides along the vehicle belt webbing 2 Has a retractor that stops the QI oe belt from being pulled out again ELR Emergency Locking Retractor with a Sliding Latch Plate once it has been pulled out The ALR in some vehicle belts may not activate unless the belt is pulled out at least 24 inches 61 cm 1 Hasa latch plate that freely slides along the vehicle belt webbing and 3 Tightens by feeding the belt webbing back into the retractor 2 Hasa retractor that locks only in an emergency situation such as sudden stop or crash This type of retractor is commonly referred to as an Emergency Locking Retractor or ELR This belt type requires the use of the lock off built into the base NOTE The base for this infant carrier is equipped with a lock off If installing the carrier without the base a locking clip must be used with a non locking lap shoulder belt Call Britax Consumer Services at 1 888 427 4829 to purchase a locking cl
14. ainer 2 Push the buckle strap retainer so that the short side will go through the desired slot in the through the slot in the cover infant carrier shell and cover and infant carrier shell to the bottom of the infant carrier shell 3 Pull the buckle away from the 4 Check that the buckle strap infant carrier to ensure the is not twisted and that the red buckle strap retainer lies flat release button faces out against the infant carrier shell Q Troubleshooting 71 Troubleshooting the LATCH Connectors If an audible click is not heard when connecting a LATCH connector e Check that the LATCH connector strap is not too tight or twisted e Clean away any debris that may be in the LATCH connector Troubleshooting the Head Restraint If the head restraint is difficult to adjust or the head restraint does not move when releasing the adjuster handle e The head restraint may be at maximum or minimum height The child s weight may be pressing against the head restraint or e The harness may need to be loosened Do not force the head restraint in either direction Troubleshooting the Harness Adjuster If the harness adjuster is hard to pull e Pull the harness adjuster strap away from the child seat parallel to the ground to tighten Do not pull at a sideways angle Do not wrap the harness adjuster strap around your hand while pulling e Check that the harness yoke is not tangled under the infant carrier Always ensure the attachm
15. all the base more than once to achieve the proper recline angle The vehicle should be parked on a level surface Follow the steps below if adjustment of the recline angle is necessary a Unbuckle the seat belt b Turn the recline adjustment knob on to adjust the recline angle Place the infant carrier in the base and check the recline angle Repeat the previous steps until a secure installation with proper recline angle is achieved Continue with installation instructions from step 3 If there is a problem achieving the proper recline angle after following the previous steps dq Uninstall the base and rotate the recline adjuster on the base to the lowest position e Remove the base from the vehicle seat Place a rolled towel or pool Place the base on the towel or noodle in the crease of the pool noodle to help level the vehicle seat base and continue installation from step 3 on page 24 28 Installing the Base QO Lap Belt Installation Before You Begin v Remove the infant carrier before installing the base if attached v Ensure that the LATCH connectors are in the storage slots in the base v Check that your vehicle seat belt is compatible with infant carrier use See pages 11 15 for more i Base Installation with Lap Belt information 1 Position the base in the desired Open the lock off by pressing down on the lock off plate lifting the tabs and then lifting the lock off plate veh
16. contour as necessary 40 Installing Your Infant Carrier without Base Installing Your Infant Carrier without Base 41 Non Locking Lap Shoulder Belt Installation Using a Locking Clip IMPORTANT When installing this restraint using a non locking vehicle belt a locking clip must be used Refer to your vehicle owner s manual for instructions on correct use of vehicle belts with child seats Before You Begin v Ensure you have a locking clip Locking clips are available for purchase by contacting Britax Consumer Services at 1 888 427 4829 3 Route the lap part of the vehicle 4 Verify that the vehicle belt is not belt through the second belt guide twisted and then buckle Do not route the shoulder portion of the vehicle belt through the belt guides v Secure child in carrier before installing carrier in vehicle Carrier Installation with a Non Locking Lap Shoulder Belt Push the infant carrier firmly into amp Hold the lap and shoulder belts the vehicle seat while removing together behind the latch plate all slack from the lap portion and and unbuckle then the shoulder portion of the vehicle belt 7 Thread the locking clip onto both belts placing it within 1 inch of 1 Place the infant carrier rear facing Pull the vehicle belt out and route the latch plate on the vehicle seat the lap portion of the vehicle belt through the first belt guide Do not route the shoulder portion of the vehicle belt
17. cover Be careful not to damage the EPS foam 1 S Remove cover from the infant tongues and chest clip carrier through the slots in the cover 1 7 Pull the harness straps buckle 64 Care and Maintenance C Refitting the Cover G Vin 1 CEFE 1 Route the upper portion ofthe 2 _ Pull the harness straps chest cover over the infant carrier clips and buckle tongues Shell through the slots in the cover Be careful not to damage the EPS foam 3 Replace the buckle by turning the metal buckle retainer so the short side will fit through the slots in the cover and infant carrier shell IMPORTANT Your infant carrier has been assembled with the buckle Strap in the inner position and the harness straps adjusted to the inner Strap loops for infants weighing less than 11 Ibs 5 kg Once your child reaches 11 Ibs 5 kg re route the buckle position to the outer slot and adjust the harness straps to the end loops for the remainder of use with that child Follow the procedures below to adjust the buckle position See pages 49 52 for instructions on removing and replacing the buckle and adjusting the harness strap loops Care and Maintenance 65 Push the buckle strap retainer 5 _ Pull the buckle away from the through the desired slot in the infant carrier to ensure the infant carrier shell and cover to the buckle strap retainer lies flat bottom of the infant carrier shell against the infant carrier shell
18. cupied infant carrier near edges of counter tops tables or other elevated surfaces Child s movement can slide infant carrier ALWAYS use harness when child is in infant carrier Never leave the occupied infant carrier when straps are loose or undone A Child can strangle in loose infant carrier straps NEVER use in or on strollers unless approved by Britax ALWAYS lift infant carrier by handle after installation in base to verify that it is secure DO NOT leave loose objects e g books bags etc in the back of a vehicle In the event of a sudden stop loose objects will keep moving potentially causing serious injuries DO NOT leave folding vehicle seats unlatched In the event of a sudden stop a loose seat back could prevent the infant carrier from protecting the child as well as it should Cover the infant carrier when the vehicle is parked in direct sunlight Parts of the infant carrier could become hot enough to burn the child DO NOT allow children to play with the infant carrier Store the infant carrier in a safe place when it is not being used for an extended period of time Do not place heavy objects on top of it 6 Child Size Height and Weight Limitations Infant Carrier Capacities and Limitations According to the American Academy of Pediatrics All infants should ride rear facing until they have reached at least 1 year of age and weigh at least 20 pounds 9 kg That means that if your infant reac
19. e LATCH Turn the recline adjustment knob to adjust the recline angle Strap Place the infant carrier in the base and check the recline angle Repeat the previous steps until a secure fit with proper recline angle is achieved Continue with installation instructions from step 7 on page 20 O Q Installing the Base 23 If there is a problem achieving the proper recline angle after following the previous steps Uninstall the base and rotate the recline adjuster on the base to the lowest position Remove the base from the vehicle seat Place the base on the towel or pool noodle to help level the base and continue installation from step 7 on page 20 Place a rolled towel or pool noodle in the vehicle seat bight 24 Installing the Base Lap Shoulder Belt Installation Before You Begin v Remove the infant carrier before installing the base if attached v Ensure that the LATCH connectors are in the storage slots in the base v Check that your vehicle seat belt is compatible with infant carrier use See pages 11 15 for more Base Installation with Lap Shoulder information belt 1 Position the base in the desired 2 Open the lock off by lifting the vehicle seating position tabs and then lifting the lock off plate 3 Pull the vehicle belt out and 4 Verify that the vehicle belt is route the lap portion under not twisted and then buckle both belt guides Installing the Base 25 Push t
20. en instructions located under the cover in the front of the child restraint Register your child restraint with the manufacturer Consult your child s doctor before using this infant carrier Some infants must be secured in a device that allows them to lie flat Never use the adjuster strap to lift or carry this infant carrier Doing so could cause damage to the harness adjuster and webbing Always carry a infant carrier by the handle or shell The primary protection for occupants of a vehicle in a collision is the structure of the vehicle a infant carrier will not protect an infant when the vehicle is seriously impacted However correctly installed an infant carrier will substantially improve the chances for survival in most crashes Make sure that all users fully understand the correct ways to use this infant carrier in a vehicle This infant carrier must not be used in shopping carts boats or other non certified applications NEVER leave child unattended The use of aftermarket covers inserts toys accessories or tightening devices is not approved by Britax Their use could cause this infant carrier to fail Federal Safety Standards or not perform as intended in a crash prevent leaving a child restrained in the infant carrier alone in the vehicle NEVER place the occupied infant carrier on beds sofas or other soft surfaces Infant carrier can roll over on soft surfaces and suffocate the child NEVER place the oc
21. ent points of the base are accessible or clear the seating area where the infant carrier will be installed of any objects or debris to ensure the infant carrier will perform as intended If the adjuster strap is fraying at the sides e Pull the harness adjuster strap away from the child seat parallel to the ground to tighten Do not pull at a sideways angle Doing so can cause the harness adjuster strap to fray at the sides See page 56 Please contact Consumer Services at 1 888 427 4829 if you have an issue not listed here 72 Warranty This child restraint was manufactured by Britax Child Safety Inc Britax warrants this product to the original retail purchaser as follows LIMITED ONE YEAR WARRANTY This product is warranted against defective materials or work man ship for one year from the date of original purchase Proof of purchase is required The exclusive remedy for this warranty is that Britax will at its option provide repair or replacement components for this product or refund the original purchase price of the product Britax reserves the right to discontinue or change fabrics parts models or products or to make substitutions To make a claim under this warranty contact Britax Consumer Services at 1 888 427 4829 or write to us using the address on the back cover of this booklet Proof of purchase is required COMPLETE AND MAIL THE OWNER REGISTRATION CARD WITHIN 30 DAYS OF PURCHASE YOU MAY ALSO REGISTER ONLI
22. ess They cannot be reattached after removal 1 Remove the canopy by 2 Unhook the cover attachment unhooking the canopy stays flaps from the carrier handle Remove the Infant carrier from the base if attached 4 Loosen the harness by pressing the harness adjuster release lever and pulling both harness straps forward C Care and Maintenance 61 5 Unbuckle the harness by pressing the red release button on the buckle and pulling the tongues from the buckle amp Unhook the harness straps from the harness yoke on the bottom of the infant carrier 8 Remove the head restraint Pull the harness straps through the shell cover and cover head restraint Be careful not to damage the EPS foam 9 Pull the infant carrier cover and foam back so the buckle Slots are visible 62 Care and Maintenance 1 OLocate the buckle strap retainer attached to the opposite end of the buckle strap 12 Turn the buckle strap retainer so that the short side will go through the slot in the infant carrier shell and cover 14Remove belly pad from the buckle strap by pulling it over the metal retainer 1 1 Pull the buckle strap retainer away from the infant carrier to loosen 13 Thread the buckle strap retainer through the slot in the infant carrier shell and cover Care and Maintenance 63 1 SRemove the comfort pads from the harness straps 1 G Remove the upper portion of the
23. evious steps until a secure installation with proper recline angle is achieved Continue with installation instructions from step 2 on page 40 NOTE Configure pool noodle s to accommodate variations in vehicle seat contour as necessary 44 Installing Your Infant Carrier without Base Q Lap Belt Installation Before You Begin v Check your vehicle owner s manual to see if your seat belt is compatible with infant carrier use See pages 11 15 for more information v There are many different types of lap belts Check your vehicle owner s manual to determine how to lock your vehicle belt system v Secure child in carrier before installing Carrier Installation with Lap Belt carrier in vehicle 2 _ Pull the vehicle belt out and route the vehicle belt under both belt guides 1 Place the infant carrier rear facing on the vehicle seat 3 Verify that the vehicle belt is 4 Push the infant carrier firmly not twisted and then buckle into the vehicle seat while removing all slack from the vehicle belt C Installing Your Infant Carrier without Base 45 amp Adjust the infant carrier handle to any locked position 6 Verify that all connections are secure Check that v The vehicle belt is not twisted v The vehicle belt is tight and locked There are many different types of lap belts Check your vehicle owner s manual for installation instructions with child restraints v The recline level indicator is within the le
24. ger not riding in a child restraint OO Securing Your Child in the Infant Carrier A WARNING Adjust harness to fit clothes the child is wearing Remove bulky coats and or jackets before putting child in infant carrier Adjust the belts provided with this child seat so they fit snugly around your child A snug strap should not allow any slack It lies in a relatively straight line without sagging It does not press on the child s flesh or push the child s body into an unnatural position Verify that the infant carrier is secure and that the harness IS properly adjusted around the child EACH time the infant carrier is used Failure to properly adjust the harness could result in death or serious injury Adjusting the Harness The harness should be properly adjusted to fit your child prior to installing the infant carrier in your vehicle Follow the steps below to prepare the infant carrier harness for use with your child Unbuckle 2 Release the chest clip by pressing the red release pressing the release button button and pulling the buckle and pulling apart the two tongues from the buckle halves 1 Unbuckle the harness by Securing Your Child 47 48 Securing Your Child Rear Facing Strap Height 3 Move the harness straps to 5 Place the child in the infant the side of the infant carrier carrier and check the harness 4 Move the buckle away from nee the seating area of the infant The correct height for
25. he base firmly into the 6 Pull the shoulder part of the vehicle seat and remove all vehicle belt tight and then Slack from the lap portion of route under both belt guides the vehicle belt Hold the shoulder belt tight amp Press firmly on the lock off and close the lock off plate plate and then close both over the vehicle belt lock off tabs Place the infant carrier into the base and press down until a Click is heard Pull up on the carrier handle to confirm attachment 26 Installing the Base QO Installing the Base 27 1 O Verify that the vehicle belt is tight and that the base is secure The base is secure when it moves less than 1 inch 2 5 cm front to back or side to side at the vehicle belt path 1 1 Verify that all connections are secure Check that v The vehicle belt is not twisted v The vehicle belt is tight and locked Check that the vehicle belt has been properly routed through the lock off and that the lock off is closed tightly v The infant carrier handle is rotated into any locked position v The infant carrier is secure If the base and infant carrier can be moved more than 1 in 2 5 cm front to back or side to side at the vehicle belt path repeat installation or choose another seating location 12 Check the recline angle 13 The proper recline angle is achieved when the level indicators on the infant carrier are within the level lines NOTE t may be necessary to install and uninst
26. hes 20 pounds 9kg before her first birthday she should remain rear facing at least until she turns 1 year old It is best for children to ride rear facing to the highest weight or height allowed by the manufacturer Rear Facing Weight 4 pounds 30 pounds 1 8 13 6 kg Use rear facing only with children e who weigh between 4 and 30 Ibs 1 8 13 6 kg and who are 32 inches in height 81 3 cm or less 9 and whose top of the head is one inch or more below the top of the child seat shell and when the harness straps are located at the harness height position at or below the child s shoulders IMPORTANT See Adjusting the Harness on page 47 WARNING The child has outgrown the infant carrier when the child exceeds 30 Ibs 13 6 kg in weight or the top of the head is less than one inch from top of the infant carrier or e height exceeds 32 inches 81 3 cm C Vehicle Compatibility 7 Using LATCH A WARNING e Use either the LATCH system or the vehicle belt methods to install this child seat Using both is not approved and may cause the child seat not to perform as intended e Verify that your vehicle is equipped with LATCH anchors If LATCH anchors are not available you must use vehicle belt installation methods e The LATCH connectors must be in an upright position and the strap should be tight and not twisted to ensure proper installation Vehicles manufactured after Septembe
27. icle seating position b 4 Verify that the vehicle belt is not twisted and then buckle 3 Pull the vehicle belt out and route under both belt guides 5 Push the base firmly into the amp Route any excess webbing vehicle seat while removing from the vehicle belt through all slack from the vehicle belt the lock off Close the lock off plate over the webbing and close both lock off tabs while pressing amp Place the infant carrier into firmly on the lock off plate The lock off is properly secured when the tabs lay flat against the lock off plate If the lock off will not close remove the excess vehicle belt webbing and tuck it under the base the base and press down until a Click is heard Pull up on the carrier handle to confirm attachment 9 Verify that the vehicle belt is tight and that the base is secure The base is secure when it moves less than 1 inch 2 5 cm front to back or side to side at the vehicle belt path Installing the Base 29 30 Installing the Base Q Installing the Base 31 1 O Verify that all connections are secure Check that v The vehicle belt is not twisted v The vehicle belt is tight and locked Check that the vehicle belt retractor is locked or Check that the vehicle belt has been properly routed through the lock off and that the lock off is closed tightly v The infant carrier handle is rotated into any locked position v The infant carrier is sec
28. ion or liability in connection with this product 73 IMPORTANT V DOUBLE CHECK EVERY TIME YOU USE THIS CAR SEAT Double Check Car Seat to Vehicle Installation M Check that the LATCH or vehicle seat belt connections to the vehicle are tight and secure M Verify the car seat cannot be moved front to back or side to side more than one inch 2 5 cm at the belt path Double Check Child to Car Seat Installation M Tug on the buckle to ensure a proper connection M Confirm that the harness straps are snug and over both shoulders and hips You should not be able to pinch excess harness strap webbing at the child s shoulder vl Make sure the chest clip is properly fastened and positioned in the middle of the child s chest at armpit level Britax Child Safety Inc Tel 1 888 427 4829 13501 South Ridge Drive Charlotte NC 28273 www BritaxUSA com USA A Britax Childcare Group Limited company
29. ip ELR Emergency Locking Retractor with Locking Latch Plate 1 Hasa latch plate that does not allow the lap part of the belt to become loose after it is buckled 14 Vehicle Compatibility Vehicle Compatibility 15 Lap Belt l Incompatible Vehicle Seat Belts Sr heat ed Hekle WARNING The following types of vehicle belts are NOT ee error compatible with this child seat onto the webbing 2 Has a retractor that stops the belt from being pulled out again once it has been pulled out The ALR in some vehicle belts may not activate unless the belt is pulled out at least 24 inches 1 Vehicle belts with top or 2 Motorized automatic enemy bottom anchor points on vehicle belts 3 Tightens by feeding the belt EE the vehicle door webbing back into the retractor Locking Latch Plate 1 Hasa latch plate that does not allow the belt to become loose after it is buckled Lap shoulder belts that 4 Lap belts forward of the have a separate retractor seat bight each for the lap section and shoulder section 2 Tightens by pulling on the belt webbing after it is buckled Lap belts that have a retractor that locks only NOTE Not all locking latch plates NS in case of a sudden stop emergency locking look and operate in the same manner retractor or ELR Refer to your vehicle owner s manual to determine the kind of seat belts used in your vehicle and how to operate them with child seats 16 Infant Carrier Features
30. le slots the buckle retainer through the The buckle can be removed as slot in the foam insert foam pad described on pages 50 51 for and infant carrier shell easier placement of the foam Ensure the buckle retainer lies flat against the infant carrier shell 5 Replace the cover Securing Your Child 53 54 Securing Your Child Placing Child in Infant Carrier Slouching LS Y Sitting Up 1 Loosen the harness by 2 pressing the harness adjuster lever while pulling both harness straps forward Press the tab and pull apart the two halves to release the chest clip 5 Place the child in the infant carrier as shown 3 Unbuckle the harness by pressing the red release button on the buckle and pulling the tongues from the buckle 4 Move the harness straps to the sides of the infant carrier Buckle the harness by inserting one buckle tongue at a time into the harness buckle Connection is confirmed with an audible click after inserting each buckle tongue Always pull on the buckle to ensure the buckle is properly connected i i k 1 pe h i r i GE AA ie e N a 1 ta k j Te i i FE tt Ti i 1 r ee Securing Your Child 55 6 Position the harness straps around the child 8 Fasten the chest clip by sliding the two halves of the chest clip together until a click is heard 56 Securing Your Child Q Securing Your Child 57 S Gent
31. ly pull up on the harness 1 OSlowly pull the adjuster strap Straps to tighten the lap section to tighten the harness around of the harness which should fit the child low on the child s body NOTE Snugly adjust the belts provided with this child restraint around your child A snug strap should not allow any slack It lies in a relatively Straight line without sagging It does not press on the child s flesh or push the child s body into an unnatural position Pull the harness adjuster away from Do not pull at a sideways angle the child seat parallel to the ground to tighten 1 1 Position the chest clip at the center of the child s chest level with the child s armpits 1 2 Verify that the harness is not twisted and the child is properly secured Check that the v Buckle is fastened v Harness straps are not twisted v Harness is snug v Chest clip is at the child s armpit level IMPORTANT e Always pull on the harness after securing the child to make sure the buckle and harness are locked If not the buckle or adjuster area may be clogged with food drink or objects that need to be removed See pages 68 70 for cleaning instructions e Always make sure that the harness is tight before each use or after any adjustments 58 General Usage Handle Positions The carrier handle must be adjusted to one of the three locked positions To adjust press and hold both handle release levers and rotate the handle in
32. nchors to ensure a proper and secure connection Always check that the LATCH connector strap is not twisted and that the LATCH connector is correctly aligned before connecting to the vehicle LATCH anchor x NOTE Ensure that the top of the LATCH connector is facing up when securing the base in your vehicle Top Locating and Storing the LATCH Connectors The LATCH connectors are located on the sides of the base inside the LATCH connector storage slots Store the LATCH connectors when not in use To remove the LATCH connectors from the storage slots 1 Press and hold the red 2 _ Pull the LATCH connector release button from the storage slot To store the LATCH connectors Push the LATCH connector into the storage slot until a click is heard to store the LATCH connectors NOTE The LATCH connectors are stored with the top facing down as shown ehicle Seating Positions A WARNING Based on crash statistics the National Highway Traffic Safety Administration NHTSA recommends that parents select the back seat as the safest location for a properly installed infant Carrier DO NOT place a rear facing child seat on the front seat with an air bag DEATH or SERIOUS INJURY can occur See your vehicle owner s manual for infant carrier installation instructions The back seat is the safest place for children 12 and under This infant carrier must only be used in forward facing vehicle seats Side faci
33. ndda 24 Lap Belt Installation vea 28 Attaching Infant Carrier to Base cisececcccvesvessaanvnnemasessedecieivasitntarenenternencenvenes 32 Releasing Infant Carrier from Base c ccesceescecseeeseceeseeseeceeeeseeseeeseaeeeseeenaeeneeseaes 33 Uninstalling the BaS Lasses Jakedamdebhiee 34 Installing Your Infant Carrier without Base rrrrrrunnnnnvnnvvvvrnnnnnnnnnnvvvvennnnnnnnnnnerr 36 Lap Shoulder Belt Install ton u uesdmsmaumanmasmnnesisissete sidelinje 36 Non Locking Lap Shoulder Belt Installation Using a Locking Clip xxsrrnvrrrnvnnnrnnnn 40 Lap Belt Installation neea aA a e AAE Erain iieis 44 Removing the Infant Caner icsecessiesssssnnnntesivsnscenscderyinsutiviansiessndsnenssumcnneedsdonedyonesieusnessess 46 Securing Your Child svscetnccatencett ccestincnsemiert ctssnncedtaueceedestncedenuedesteshuxedemcertsusdvecedunven 47 Adjusting the H mess Laesspasssgmereameetmnjj v bubednagaasaassien 47 H ness Strap AM STET vvs av Sesandkanees 49 Adjusting the BUCkle Luse 50 Removing th BUG le iinne EEE EEEE NEN 50 Replacing the Buckle Lunn ence cisc te peasunenenvesevesslazansendestonadstaasesaacbevesnteeaseneieneee 52 LOW Birk Weight INE i FOA sasadara aiiai anes 53 Placing Child in Infant Carrier scisssieosssssinssiiesswsnsesanancsaiesnessncoasatancneeantouceusteduedendenssiinsnevands 54 General USJGE Lun neta citcencccenects cereenecttecccd nedeendectwedtameccencctemccctsiieemmeteweccnseebetotens 58 Care and Maintenance
34. ng or rear facing seats CANNOT be used If in doubt about installing the infant carrier consult the vehicle owner s manual Some vehicles have no seating positions which are compatible with this infant carrier or any other infant carrier If in doubt contact the vehicle manufacturer for assistance See diagram below 10 Vehicle Compatibility Q QO Vehicle Compatibility 11 Compatible Vehicle Seat Belts NOTE The information in this section only applies to installation with vehicle safety belts Vehicle seat belts compatible with this child seat are Lap shoulder belts and Lap only belts equipped with a switchable retractor or an automatic locking retractor ALR or a locking latch plate Vehicle seats and safety belts differ from vehicle to vehicle Your vehicle owner s manual will have information on the types of vehicle belts in your vehicle Refer to your vehicle owner s manual for specific information about vehicle safety belts and their use with child seats Lap Shoulder 3 Point Belt Switchable Retractor in ALR Automatic Locking Retractor Mode with Sliding Latch Plate 1 Has a latch plate that freely Slides along the vehicle belt webbing 2 Has a retractor that can be switched so that it always locks Automatic Locking Retractor ALR or so it only locks during sudden stops or crashes Emergency Locking Retractor ELR To use this infant carrier with this type of vehicle belt you must switch to the AL
35. olvents Use abrasive cleaners Disassemble the harness adjuster Iron the harness adjuster strap NOTE Periodically check the harness adjuster area to be sure it is clean and free of food coins dirt or other debris If debris is present it must be removed to prevent interference with the harness adjuster mechanism Cleaning the Buckle Remove the Buckle 1 Remove the infant carrier from the base if attached 2 Pull the infant carrier cover 3 Locate the buckle strap and foam back so the buckle retainer attached to the Slots are visible opposite end of the buckle strap on the bottom of the infant carrier shell Clean the Buckle Care and Maintenance 69 Pull the buckle strap retainer 5 Turn the buckle strap retainer away from the infant carrier to so that the short side will go loosen through the slot in the infant carrier shell and cover Pull the buckle strap retainer through the slot in the infant carrier shell and cover Remove belly pad from the buckle strap by pulling it over the metal retainer THOROUGHLY RINSE using warm water Fig A TEST THE BUCKLE by fastening and unfastening until an audible click is heard after inserting each buckle tongue If clicks are not heard repeat cleaning procedure TOWEL DRY DO NOT Lubricate Use solvents Use abrasive cleaners Use soap or household detergents 70 Care and Maintenance Replace the Buckle 1 Turn the buckle strap ret
36. on the harness Strap for the size of your infant Use the bottom loops for infants 11 lbs 5 kg and under and the end loops for infants 11 Ibs 5 kg and over DO NOT use the middle section between the end and bottom loops 4 Slide the harness strap onto the harness yoke Securing Your Child 49 50 Securing Your Child IMPORTANT Harness straps must hang as shown by V above Do not tuck the straps behind the harness yoke Pull on the harness straps to ensure the harness strap webbing is secured within the slots of the harness yoke Adjusting the Buckle IMPORTANT Your infant carrier has been assembled with the buckle Strap in the inner position for infants weighing less than 11 Ibs 5 kg Once your child reaches 11 Ibs 5 kg re route the buckle position to the outer position Follow the steps below to adjust the buckle position See page 49 for important information for adjusting the harness straps for the fit of your child Removing the Buckle 1 Remove the infant carrier from the base if attached 2 Pull the plastic flaps on the cover 3S _ Pull the infant carrier cover and foam from the infant carrier shell back to access the buckle slots Securing Your Child 51 4 Locate the buckle strap retainer 5 Pull the buckle strap retainer away attached to the opposite end of from the infant carrier to loosen the buckle strap on the bottom of the infant carrier shell amp Turn the buckle strap retainer so
37. out Base 39 Adjust the infant carrier handle to any locked position 8 Verify that all connections are secure Check that v The vehicle belt is not twisted v The vehicle belt is tight and locked Check that the vehicle belt retractor is locked or Check that the latch plate is locked or Ensure that a locking clip has been properly installed v The infant carrier handle is rotated into any locked position v The infant carrier is secure If the infant carrier can be moved more than 1 in 2 5 cm front to back or side to side at the vehicle belt path repeat installation or choose another seating location Check the recline angle 1 O The proper recline angle is achieved when the level indicators on the infant carrier are within the level lines NOTE t may be necessary to install and uninstall the infant carrier more than once to achieve the proper recline angle The vehicle should be parked on a level surface Follow the steps below if adjustment of the recline angle is necessary a Unbuckle the seat belt b Place a rolled towel or pool Place the infant carrier on the noodle in the vehicle seat bight towel or pool noodle to help See note below level the base Repeat the previous steps until a secure installation with proper recline angle is achieved Continue with installation instructions from step 2 on page 36 NOTE Configure pool noodle s to accommodate variations in vehicle seat
38. r 1 2002 have seating positions equipped with LATCH anchors If a vehicle is equipped with LATCH look for the LATCH or tether symbols identifying anchor locations Vehicle Seat Head Restraint Forward Facing Tether Anchors Vehicle Seat Belt D Retractor Lap Shoulder Vehicle Seat Belt LATCH Anchors Vehicle Seat The figure above shows typical locations for lower anchors and tether anchors in a vehicle Check your vehicle owner s manual for the exact anchor locations and information on use with an infant carrier 8 Vehicle Compatibility Vehicle Compatibility 9 Only use the LATCH system on this infant carrier in a seating position designated by the vehicle owner s manual Refer to your vehicle owner s manual or contact the vehicle manufacturer for the maximum weight rating for their LATCH anchors This infant carrier was designed to be used with lower LATCH anchors in vehicle designated seating positions The standard vehicle seat spacing between lower LATCH anchors is 11 inches 27 9 cm This infant carrier can be used in a seating position with up to 20 inches 50 8 cm of space between the LATCH anchors if the vehicle manufacturer allows Up to 20 inches 50 8 cm Check your vehicle owner s manual for information on using child restraints in center seating positions without designated LATCH anchors Connecting the LATCH Connectors The LATCH connectors must be properly aligned with the vehicle LATCH a
39. rrier with 2 Setthe infant carrier into base 1 If necessary rotate the handle 2 Locate the release handle at the slots in the base ensuring until an audible click is heard into the carrying position the rear of the infant carrier that the infant carrier faces the rear of the vehicle 3 Pullup on the infant carrier 4 Rotate the handle to any 3 Squeeze and hold the release 4 Lift the infant carrier away handle to ensure it is properly locked position handle from the base secured 34 Uninstalling the Base Uninstalling the Base 35 Removal of Base LATCH Installation IMPORTANT Always remove the infant carrier before attempting to remove the base 1 Open the lock off by lifting the 2 Press the LATCH adjuster tabs and then lifting the lock release button to release off plate tension in the LATCH strap 3 Press the LATCH connector release button on each connector to detach them from the LATCH anchors 4 amp Remove the base from the vehicle Removal of Base Vehicle Belt Installation IMPORTANT Always remove the infant carrier before attempting to remove the base 1 Open the lock off by lifting the 2 Press the release button on tabs and then lifting the lock the vehicle belt buckle off plate Pull the vehicle belt from the base belt guides Remove the base from the vehicle Installation without Base Lap Shoulder Belt Installation 36 Installing Your Infant Carrier without Base
40. to one of the three locked positions C C General Usage 59 1 To raise the canopy pull the canopy fabric at the top of the canopy arch toward the bottom of the infant carrier To collapse the canopy push the canopy fabric at top of canopy arch in toward the top of the infant carrier User Guide Storage Tuck the user guide and lanyard under the cover in the front of the infant carrier to store Seat Storage Store the infant carrier in a safe dry place when it is not being used for an extended period of time Do not place heavy objects on top of it Cover the infant carrier to help keep it clean Remove and wash the cover and canopy see instructions on pages 60 65 before using the seat the first time after storage Transporting an Unoccupied Infant Carrier Attach this infant carrier to a securely installed base or install the infant carrier with a vehicle seat belt without the base even when it is not occupied In a crash an unsecured infant carrier may injure vehicle occupants in your vehicle before transport See pages 18 46 for installation instructions 60 Care and Maintenance Q Cover Removal A Do not except as described in this booklet attempt to disassemble any part of the infant carrier or change the way its harness or the vehicle belts are used Do not take apart the harness It is unnecessary and dangerous to do so e Never remove the buckle tongues from the harn
41. ure If the base and infant carrier can be moved more than 1 in 2 5 cm front to back or side to side at the vehicle belt path repeat installation or choose another seating location 1 1 Check the recline angle 1 2 The proper recline angle is achieved when the level indicators on the infant carrier are within the level lines NOTE t may be necessary to install and uninstall the base more than once to achieve the proper recline angle The vehicle should be parked on a level surface Follow the steps below if adjustment of the recline angle is necessary a Unbuckle the seat belt b Turn the recline adjustment knob on to adjust the recline angle Place the infant carrier in the base and check the recline angle Repeat the previous steps until a secure installation with proper recline angle is achieved Continue with installation instructions from step 3 If there is a problem achieving the proper recline angle after following the previous steps dq Uninstall the base and rotate the recline adjuster on the base to the lowest position e Remove the base from the vehicle seat Place a rolled towel or pool Place the base on the towel or noodle in the crease of the pool noodle to help level the vehicle seat base and continue installation from step 3 on page 28 32 Installing the Base QO Installing the Base 33 Attaching Infant Carrier to Base Releasing Infant Carrier from Base 1 Align the infant ca
42. vel lines v The infant carrier handle is rotated into any locked position v The infant carrier is stable If the infant carrier can be moved more than 1 in 2 5 cm front to back or side to side at the vehicle belt path repeat installation or choose another seating location 7 Check the recline angle amp The proper recline angle is achieved when the level indicators on the infant carrier are within the level lines NOTE t may be necessary to install and uninstall the infant carrier more than once to achieve the proper recline angle The vehicle should be parked on a level surface 46 Installing Your Infant Carrier without Base Follow the steps below if adjustment of the recline angle is necessary a Unbuckle the seat belt Place the infant carrier on the towel or pool noodle to help level the base b Place a rolled towel or pool noodle in the vehicle seat bight See note below Repeat the previous steps until a secure installation with proper recline angle is achieved Continue with installation instructions from step 2 on page 44 NOTE Configure pool noodle s to accommodate variations in vehicle seat contour as necessary Removing the Infant Carrier 1 Unbuckle the vehicle belt 2 Pull the vehicle belt from the infant carrier belt guides IMPORTANT f you have installed the infant carrier using a locking clip ensure that the locking clip is removed before the vehicle belt is used by a passen
Download Pdf Manuals
Related Search