Ademco Vista 10se
Contents
1. be used in place of the 4 digit security code when disarming the system Disarming Enter 4 digit security code OFF 1 key Bypassing Zones Enter 4 digit security code BYPASS 6 key zone number s Forced Quick Bypass if enabled To automatically bypass all faulted zones use the Quick Bypass method Enter 4 digit security code BYPASS then wait for all open zones to be displayed Arm when display indicates Bypass and Ready to Arm Chime Mode Enter 4 digit security code CHIME 9 key To turn chime off enter code CHIME again SUMMARY OF ARMING MODES Features for Each Arming Mode Exit Entry Perimeter Interior a A 10 1 VISTA 10SE Installation and Setup Guide Panic Keys There are three individual panic keys and or on some keypads panic key pairs If programmed they can be used to manually initiate alarms and send a report to the central station Each key or key pair can be individually programmed for 24 hour Silent Audible Personal or Fire Emergency responses The panic function is activated when both keys of the appropriate key pair are pressed at the same time or the appropriate lettered key is pressed for at least 2 seconds The panic functions are identified by the system as follows Displayed as Zone Brost T B ARMED oO READY A Pd TE Le Notes c LJ 7 8 9 e Keys A B C are not on all keypads ciel o FT2. disarm the system under threat When used the system will act normally but can silently notify the central station if that service has been provided e Toprogram a Duress code enter Master code 8 key 8 key new 4 digit Duress Code e Tochange a Duress code enter Master code 8 key 8 key desired 4 digit Duress Code e Todelete a Duress code enter Master code 8 key 8 key and stop The Duress Code must differ from the Master Code or any other User s Code Keypad Functions The following is a brief list of system commands For detailed information concerning system functions refer to the User s Manual Function or Keypad Display Description Silence Alarms Pressing any key silences the keypad sounder for 10 seconds Disarming the system silences both keypad and external sounders Disarmed Not Ready Before arming the system must be in the READY condition all zones must be intact If the NOT READY message appears press the READY key to display faulted zones Arming AWAY Enter 4 digit security code AWAY 2 key Arming STAY Enter 4 digit security code STAY 3 key Arming INSTANT Enter 4 digit security code INSTANT 7 key Arming MAXIMUM Enter 4 digit security code MAXIMUM 4 key Quick Arming if enabled Simply press key in place of code then press AWAY STAY INSTANT or MAXIMUM to arm system as desired Note that the 1 key cannot
3. SECTION 10 System Operation Security Codes The system supports up to seven security codes Installer Master four secondary user and Duress described as follows Code Description of Code Function and Programming Installer User 1 The factory default Installer Code is 4 1 1 1 but may be changed in field 20 The Installer code cannot be used to disarm the security system if it was not used to arm the system The Installer code must be used to program the 4 digit Master Code Master User 2 The Master security code permits access to the system for arming disarming etc Opening and dosing reports are sent for the Master Code as No 02 with the appropriate subscriber number e Toassign a Master Code enter Installer Code 8 2 4 digit Master Code e Tochange the Master Code enter Master Code 8 2 New Master Code New Master Code Only the Master code can be used to assign change or delete the secondary 4 digit user codes Secondary Users 3 6 Secondary User codes permit access to the system for arming disarming etc e Toassign or change a Secondary security code enter Master Code CODE key User No 3 6 desired 4 digit Secondary Code To delete a Secondary security code enter Master Code CODE key User No 3 6 Secondary user codes are sent as Nos 3 through 6 respectively with the appropriate subscriber number Duress User 8 Intended for use when forced to arm or
4. e Key D if present is not active here u PANIC J X Shown above is a typical 2 line alpha keypad with individual Panic keys shown lettered Important For the Silent Panic functions to be of practical value the system must be connected to a central station 4285 4286 VIP Module if used Refer to the separate instructions supplied with the VIP Module for information concerning its operating procedures Relay Outputs if used If relay outputs are used two keypad entries available to the user are included among the system operation choices 34 and 35 that may be programmed see SECTION 6 Output Device Programming They can manually activate or deactivate the relay s for starting or stopping some action such as turning lights on or off etc These keypad entries are Security Code 4 7 and Security Code 8 NOTE The keypad entry that is used to Start Stop the action cannot also be used to Stop Start it The opposite action must either be performed by the other keypad entry or by some other event or operation offered in SECTION 6 Output Device Programming Exit Error Alarm Displays if programmed 2 Line Alpha Display Fixed Word Display Meaning A display of CANCELED ALARM or CA and a zone indication appears if an exit or interior zone contained a fault during closing at the time the exit delay ended e g exit door left open and the system was disarmed duri
5. ng the subsequent entry dday time The alarm sounder and keypad sound continuously but stop when the system is disarmed No message will be transmitted to the central station A display of EXIT ALARM or EA and a zone indication will appear if an exit or interior zone contained a fault during closing at the time the exit delay ended and the system was NOT disarmed during the subsequent entry dday time The alarm sounder and keypad sound continuously until the system is disarmed or timeout occurs An exit alarm message is sent to the central station The EXIT ALARM display etc also result if an alarm from an exit or interior zone occurs within two minutes after the end of an exit delay CANCELED ALARM CA EXIT ALARM EA NOTE To clear display in either of the two above cases use a second OFF sequence CODE plus OFF 1 key to clear the display 10 2
Download Pdf Manuals
Related Search