Victoria ENG Balboa.indd
Contents
1. under the bathtub close to other electrical devices of the bathtub more than 20 cm above the floor The bathtub must never be connected using a plug Zone 0 is the area inside the bath Zone 1 is the zone 0 area plus the space up to 2 25 m above the floor Zone 2 is the zone 1 area extended by 0 6 m again up to 2 25 m above the floor Zone 3 is the area reaching 2 4 m beyond zone 2 up to 2 25 cm above the floor 18 Location of protection zones Water connection 1 2 for water filling Sewage connection 50 mm Skimmerfilter 1580 1765 230 V electric connection with 5 7 kW efficiency protected 3 x 4mm Location of SPA Victoria connections 2 7 SERVICE VALVE In Victoria SPA there are two gate valves which shut off the water supply to the pump and heater If valves are closed they provide overhaul repair or even replacement of equipment in a spa filled with water 19 2 8 MAINTENANCE OF ACRYLIC ELEMENTS Only mild fluids not containing acetone abrasive or caustic substances should be used to clean the bath The structure and low level of surface adhesion of acrylic mean that keeping the bath clean should not be a problem Mechanically damaged gloss acrylic small shallow scratches can be easily repaired In the case of small scratches a small amount of wax free car polish should be used Deeper scratches may be removed by sandpaper in order2. and ensured efficiency of the electrical connection in respect of the equipment for standard equipment the rated power consumption is ab 5 7 kW 230V 50 Hz 3x4 mm 8 7 kW 3N 400V 50 Hz 5x4 mm optional with regard to the safety of the users in all cases the supply cable must be protected by means of a differential current switch with the standard rated switch off current of 30 mA c water supply and drainage 50 d leveled floor floor drain recommended e adequate hardness of bed adjusted to SPA weight f sufficient ventilation indoors g in case of a bath installed in a closed premise access to the electrical equipment must be provided for maintenance or inspection purposes 2 3 BATH POSITIONING In order to ensure proper operation conditions the floor should be very well levelled All the bath legs should be on a solid and hard surface The total weight of the bath with water and four people is about 1450 kg The weight of the bath should be equally spread over the 11 bath legs The surface load is 582 kg m 1580 1765 2 4 PREPARATION OF ELECTRICAL AND WATER CONNECTIONS Victoria SPA requires at most ca 5 7 or 8 7 kW of power depending on configuration In both cases the minimum cross section of the cord should be at least 3x4 mm or 5x4 mm respectively In the case of tubs installed outdoors a cord with insulation resistant to deterioration caused by weather conditions
3. be handled by children Start set test container and DPD and Phenolred tablets If the measured pH is outside the range 7 2 to 7 6 it will be necessary to use SPA Victoria granules to correct the pH value 1 Dinominus pH decreasing granules Dosage about 10 g 1000 litres to lower pH by 0 1 in case of Victoria 10g The granules should be poured over water surface as the filtration pump is on The pH measurement should take place directly after the correction Do not add the granules anywhere close to the skimmer 2 Dinofresh active oxygen granules for water disinfection to be added to the skimmer Dosage 25g 1000 litres is a start value 25g for Victoria and then in 5g doses or multiplied doses to restore the 5 8 mg l Dinofresh level in water 3 Dinoclean S alkaline liquid and strong chemical to clean the rim of the bath and dissolve fats It is perfect to clean any greasy stains from the walls or the rim of the bath and to remove calciferous deposits Dosage spread concentrated or dissolved 1 10 agent on dirty surfaces using a brush Rinse thoroughly after a short period of time Do not let the agent dry before rinsing A set of disinfecting agents for VICTORIA SPA can be purchased at your sales agent It is a natural phenomenon that in SPA baths the pH value of water tends to increase However very rarely the pH value decrease can be observed It is then recommended to use Dinoplus granules which can be order
4. filtration and massage pump water filter with a renewable cartridge for multiple use water suction point pipes and PVC piping Filter replacement Tilt the hatch towards the inside of the bath Remove element B and subsequently element C Remove element D and subsequently element E Clean or replace filter inserts D and E Install new filters in the opposite order i e E and D Install elements C and B Cleaning relies on rinsing of the insert with warm running water e C NOOR WD Skimmer filter used Recommended for SPA Victoria Rinsing every 2 days Replacement not less frequent than once a year The skimmer filter used in the SPA Victoria has the filtration area of 1 86 m and the flow capacity of approximately 19 m h Skimmer filter Water pump Water ozone Injektor Filtration system scheme for a SPA Victoria Water 1 10 DISINFECTION Disinfection process in the SPA Victoria is ozone based Ozone is used during filtration Additionally the bath is equipped with a START SET for pH correction and disinfection with active oxygen as described in Part 1 11 1 11 MEASUREMENT AND TREATMENT FORMULA SET Before the first bath and always once in 2 weeks please check the water pH with the enclosed Di
5. may be fitted to the frame this time in a clockwise direction until stop The exchange should be performed while the bath is NOT operating Removing a jet insert Fixing a jet insert It is advised at least once every 6 months to take out from big jets their inserts for cleaning of any possible dirt Unscrew the insert from frame remove gently using pliers inner part of the jet Clean inner part of the jet Put back the inner part and screw the insert to the frame in a clock wise direction 1 3 CONSERVATION SUBSTANCES The acrylic surface of the bath is covered with a thin layer of wax being the remaining of the polishing process Metallic elements have been coated with silicone oil for protection purposes The SPA should be washed off e g with a dishwashing detergent prior to filling the bath with water 1 4 VENTILATION High water temperature during bath in the bath 39 C causes emitting of big amounts of steam An efficient ventilation system should be provided in the room with the bath Installing of a steam condenser in the room which will maintain constant air humidity will minimize the risk of dampening of walls and ceiling An air conditioning system in the building allows for elimination of the steam condenser Such problem does not exist in case of a bath operating in open air conditions 1 5 MAIN FUNCTIONS ACCESSIBLE FROM THE ELECTRONIC CONTROL PANEL LoS NV BLOWER LIGHT UEFI STANDARD SET HEAT I PNP SOL
6. protections do not function properly To prevent activation of the bath without water switch off the electrical power by pressing the test button on the differential current switch The bath can be connected to the water and sewage systems permanently or the bath can be filled and drained by means of flexible hoses disconnected after each operation The flexible hose set of the bath includes a T pipe with a 1 2 coupling for filling of the bath through the hydro massage jets The fixed piping system includes release valves located near the skimmer filter at the outlets of which fixed or removable hose connection with the sewage system should be provided T pipe with a 1 2 coupling It is recommended that the bath is permanently connected to the sewage system due to the risk of water overflowing through the emergency overflow system 2 5 GROUNDING CABLE CONNECTION In order for the residual current device and the tub itself to function properly a grounding cable with a cross section of at least 2 5 mm must be installed Connect the cable to the frame as illustrated Connect the other end of the cable to the protective grounding of the building s electrical wiring Place of connection of the earthing wire 2 6 CONNECTION TO MAINS As the bathtub is protection class equipment it has to be permanently connected to power supply TN S type using IP X5 junction box It is recommended to install the connection box in area
7. ske Y X 0 4 VS 4 ve SN Boe MODE PROG Victoria SPA control panel 1 5 1 FIRST START UP FILL THE BATHTUB WITH WATER BEFORE FIRST START UP After power is turned on the spa bathtub switches to the pump venting mode P I When in that mode press Jets button s several times to make sure that the pumps are not air locked The duration of the mode is less than 5 minutes Press Warm or Cool buttons to exit the mode After the venting is completed the bathtub will switch to standard operation mode A EV 1 5 2 TEMPERATURE ADJUSTMENT 80 F 104 F 26 0 C 40 0 C When in standard operation mode the bathtub controller enables water temperature adjustment within the 8 _ range mentioned above Temperature of water inside the spa is displayed in a continuous manner The value displayed is correct if the pump has been operating for at least 2 Minutes Press Warm or Cool button once to display water temperature The preset temperature can be changed by pressing the same buttons again Temperature adjustment mode is indicated by a flashing value of the current setting Three seconds after the button is pressed for the last time the value indicated on the display stays on and the current spa temperature is displayed 1 5 3 JETS 1 Press the Jets 1 button to start stop the pump 1 and toggle low high speed if available If the pump operates at low speed it switches off after 4 hours If the pump operates at high speed
8. Hydromassage intensity is decreased by turning the regulator knobs clockwise 11 Each of the regulators is responsible for controlling a different jet section fixed mini jets large fixed directional jets large rotary jets fixed mini ozone jet water suction control panel aeration regulators 1 6 2 Airmassage pearl bath In air massage heated air is pumped into water by a blower Millions of bubbles come from the perforated bath bottom actively relaxing the body The bubbles stimulate circulatory system relax muscles and joints Their activity may be compared to a normal hand massage It soothes the nervous and respiratory system and improves metabolism The airmassage system is made of the following elements air channels situated on two levels forming an integral part of the bath topped with a number of openings within the water section of the bath a blower a loop protecting against water intrusion into the blower 1 7 COLOURFUL LED SPOTLIGHT MULTI POINT LED LIGHT OPTIONAL If the tub is equipped with the multi colour light feature the colour can be changed by switching the light off and on again The light colour changes in a sequence Colourful spotlight settings Slow colour Colours transition gracefully from colour to colour cycling through the entire colour wheel Each colour cycle lasts approximately 3 minutes Fast colour Colours transitio
9. Oxygen atoms t a a or UV light Operating only during filtration O Ozone producing process Ozone is healthy itis more and more popular in beauty treatment helps to remove stretch marks cellulite and wrinkles improves complexion helps to treat varicose veins and skin diseases helps in heart and circulatory system problems soothes problems connected with menopause Why is ozone necessary in SPA it has antiseptic properties helps to keep the bath clean helps to keep water clean fresh and clear eliminates any unpleasant water smell eliminates fungi and yeast in water refilling with water does not need to be frequent 1 8 1 UV LAMP OPTIONAL A special UV lamp generates UV C radiation with a wavelength of 253 7 nm which neutralizes bacteria viruses and other primitive organisms preventing their reproduction at the same time The benefits of UV C radiation ensures fresh clean and clear water disinfects water safely and efficiently keeps the formation of mold bacteria and algae under control reduces the use of chorine and other chemicals by up to 80 prevents the smell of chlorine as well as skin and eye irritation including eye redness is more environmentally friendly than traditional methods Ozonation and the UV lamp work only during filtration 1 9 VICTORIA SPA FILTRATION SYSTEM SPA VICTORIA filtration system comprises skimmer filter
10. POOLSPA SPA Bath VICTORIA SPA 178 Installation and user manual Warranty Dear customers Thank you for trusting us and buying our product The POOLSPA company one of the leaders in the European hydromassage bath market has been offering its world class quality products for many years The endurance reliability and safety of our baths has always been of greatest importance to us that is why we always use materials and devices from reputable suppliers The manual will help yoy learn about the bath installation and its use In this way you will be able to use the bath without any problems for many years to come Have a great time and enjoy our baths CONTENTS 1 1 Technical specification W u sssssssssseneeseeee ket k kk E ERE ERE RER EEN E REE ENERET EET E ERE REE ataneseneeaaee 6 ES E E oe GRO eA DR AA A A ae ee ee Ree TC ene ae re eee Er 7 TE CONSENVaTONR SUD STAN CE en ene nt ae en Aine ere te ae rc pe ane ee 8 iA VENAN aan RE O EAEE ARE 8 1 5 Main functions accesible from the electronic Control Panel cccceccceeeeeeeeeteeeeeeeeees 8 lO MaS SGO pst ce Sy SE SENERE REE ESTERE Mange eee lars yieacends Gases eaaeeaeepda hese EET OSSE SERENE easton 11 1 7 Colourful led spotlight multi point led light Optional cccecccseecseeceeeeeeeeeeeeseeeseees 12 MEE AN MCT OZ ONIZING re Er sade E E codec andeseeetainceacces dans 13 1 9 Victoria SPA filtration system sssssssssnen
11. buying a portable Victoria SPA SPA Victoria allows you to appreciate the advantages of hydromassage for four people sitting places both outside a building and inside a large bathroom The bath is equipped with an ozonator which makes it easier to keep the water clean and is very effective in beauty treatment The qualities of ozone are described in detail in Part 1 8 Thanks to the antifrost system itiseven possible to take a bath when the outside temperature below freezing point The SPA Victoria comprises electronic control panel with a display 2 hydromassage aeration regulators 3 KW electric heater additional electric heater 3 KW option 1 5 kW hydromassage pump 1 2 W axial blower water ozonator UV lamp optional no ozone jet antifrost system for outside temperatures below freezing point water temperature sensor hydromassage set of jets 25 pcs including 1 ozone jet air channels 95 openings water suction point white underwater LED light multi color light optional LED spotlight 24 points optional 3 polyurethane cushions gray in a standard option wooden panel in mahogany or pine colour optional plastic panel in gray mahogany or pine optional wooden stairs in mahogany or pine colour optional thermal cover optional It is recommended to turn the power off with the manual switch before draining the tub to prevent the hydro ma
12. e sections is excluded unless the law of the land expressly attributes liability Recommendations Before using the equipment read carefully through the instructions included with the Spa ROCA POLSKA Sp z 0 0 Zaktad produkcyjny POOLSPA ul Dabskiego 35 72 300 Gryfice tel 48 91 38 777 00 fax 48 91 38 777 01 www poolspa pl e mail info poolspa pl 21 22 TECHNICAL PRODUCT SHEET MODEL FITTINGS Victoria SP FACTORY NUMBER DATE OF PRODUCTION AND TESTING NOMINAL POWER REQUIREMENTS 9 KW FUSING REQUIREMENTS 32 A VOLTAGE FREQUENCY 230V 50 Hz THERMAL PROTECTION QUALITY CONTROL 23 POOLSPA company has the policy of constant improvement of products and reserves the right to introduce changes to the specification and colours without a prior notification However POOLSPA makes all efforts to ensure that the specifications are updated on the date of publishing ROCA POLSKA Sp z 0 0 Zaktad produkcyjny POOLSPA ul Dabskiego 35 72 300 Gryfice tel 48 91 38 777 00 fax 48 91 38 777 01 www poolspa pl e mail info poolspa pl 5 06 2013 P13000130
13. e temperature of 20 F 10 C only during filtration cycle SLP message appears on the display ILF message and the current water temperature value are displayed alternately during pump operation 1 5 8 SETTING FILTRATION CYCLES The controller can be operated in two filtration cycles The first preset filtration cycle starts at 8 00 a m and ends at 10 00 a m The other preset filtration cycle starts at 8 00 p m and ends at 10 00 p m During the filtration process pump 1 is operated at low speed with ozone generator on 1 5 9 CHANGE OF FILTRATION CYCLE It is not necessary to change the filtration cycles If for any reason it is necessary to change previously programmed adjustments FILTER 1 for a m and FILTER 2 for p m the controller allows doing this To change the cycles push the buttons consecutively during 3 seconds Time MODE PROG MODE PROG It will appear the communicate SET START FILTER 1 on the screen Change the time of starting the filtration by pushing the buttons Warm or Cool To put new adjustments into memory of the controller push the button 9 MODE PROG The system will be switched to the mode of SET STOP FILTER 1 Changing the time of finish the filtration will be done by pushing the buttons Warm or Cool the same way as above programming START FILTER 1 Approval of the new adjustments will be done by pushing the button MODE PROG Programming the filtration for the afternoon FILTER 2 suppose to be done the same wa
14. ed through the showroom of the Victoria SPA manufacturer Set of measurement treatment agents to be purchased at sales showrooms mMm 1 B 1 12 THERMAL COVER ADDITIONAL OPTION The SPA Victoria can be optionally provided with a thermal cover When is it necessary to have a thermal cover when the bath is going to be used outdoors i e in a garden the cover prevents the water from excessive cooling down and keeps the bath clean when the bath is going to be used very frequently indoors the cover serves to prevent the water from excessive evaporation 2 times a month is recommended to open the slipcover of the thermal cover for removing the water from it Very gently pull forward the masking strips then gently lift the cover remove the mounting brackets from the threshold strip on the bottom and take out the casing masking strip casing mounting brackets 16 PART 2 INSTALLATION MANUAL 2 1 TRANSPORT The bath should only be transported in the original manufacturer s packaging After unpacking the bath can be carried by the aluminum frame or acrylic elements The pipes and cables must not be used as handles grips 2 2 SITE PREPARATION The SPA VICTORIA portable bath may be operated both indoors and outdoors The site for the bath should comply with the following conditions a the proper area and the proper transportation routes in case of closed premises b proper electrical supply
15. essure need to consider special conditions created inside the SP baths and consult their physician before using such baths We recommend using hydromassage treatments in water of the average temperature of 37 degrees for approximately 20 minutes It is recommended that children using the equipment are always accompanied by an adult This equipment is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the equipment by persons responsible for their safety Children should be supervised to ensure that they do not play with the equipment Before taking a bath make sure that the water level in the bathtub is correct If the water level is 3 4 cm above the skimmer filter you can start the bath If the water level in the bathtub is not correct the filtering system may not operate properly and water heating will not be possible Remember to add water into the bathtub from time to time Parts comprising active components excluding those supplied with safe voltage not exceeding 12V cannot be accessible for the person inside the equipment Parts comprising electrical components excluding remote control equipment should be located or fixed so that they cannot drop into the bathing equipment Keep this manual for future reference PART 1 INSTRUCTION MANUAL Congratulations on
16. is required Protect the cord against mechanical damage If the insulation or cord is damaged always replace it due to the risk of electric shock A differential current switch with an indicated test button For 3x4 mm cords protect the tub s power cord with a C type residual current device and a trigger current of 32 A and for 5x4 mm 16 A For safety reasons always connect the tub s power cord to the mains using an electrical connection protected by a residual current device with a rated cut off current of 30 mA It is recommended to check the residual current device periodically according to the guidelines for testing and resetting such devices The SPA tub should be connected to the building s electrical wiring permanently The electrical wiring should be equipped with the appropriate manual cut off mechanism enabling the opening of contacts on each power supply pole In addition equipotential bondings must be made using the clamp located on the tub support frame The minimum cross section of the equalizer power cord is 4 mm 17 All electrical connections should be made by a qualified electrician For safety reasons check the effectiveness of the anti electric shock protection from time to time by pressing the TEST button on the residual current device If the power is not turned off immediately after pressing the button unplug the tub manually and contact a qualified specialist Do not use the SPA tub if the
17. it switches off after 15 minutes Remember that it is not possible to deactivate the low speed when the filtration process is running 1 5 4 JETS 2 JETS 3 BLOWER IF AVAILABLE Press a given button once to start stop the corresponding device Each of the devices is turned off after 15 minutes 30 1 5 5 LIGHT A Press the Light button to switch the spa light on The light is turned off after the button is pressed again The light switches off after 4 hours 1 5 6 SETTING THE TIME If the spa is operated for the first time SET TIME message is flashing on the display To change the current setting press the following buttons Time Mode Prog Warm or Cool one by one After the last button of the sequence is pressed the hour setting mode is activated The hour visible on the screen will be changed automatically To stop it from changing press Warm or Cool buttons one more time and press Time button to confirm the setting 1 5 7 MODE PROG There are three operating modes available for the controller The mode is changed by pressing Warm or Cool button M TAN In the standard mode the set temperature is maintained and the STANDARD icon is displayed When in the eco mode the spa is heated up to the preset temperature only during filtration cycles Fon message appears on the display Fen message and water temperature value are displayed alternately during pump operation When in the stand by mode the spa is heated up to th
18. n from colour to colour cycling through the entire colour wheel Each colour cycle lasts approximately 1 minute Slow random colour Colours step or jump from one colour to the next in random order Each colour duration lasts approximately 10 15 seconds Fast random colour Colours step or jump from one colour to the next in random order Each colour dura tion lasts approximately 5 seconds High speed random colour A rapid series of intense flashes of varying coloured light Cross fade Colour cycle back and forth gracefully between blue and green Total cycle lasts 1 minute Fixed colour Static display of a single colour Available colours include green and blue Colourful multi point light settings 6 brilliant colors and 4 color transition programs Tidal fade Cool color mix slow transitions between green and blue tones Afterburner Fade Warm color mix slow transitions between red and orange tones Spectrum Slowdance Slow transitions between all six colors Color Burst Fast strobe through all six colors 12 1 8 WATER OZONIZING Oxygen O Ozone O ER O The ozonized air has apart from a nice scent many therapeutic i O O and antiseptic properties It greatly helps in keeping the water clean both in the bath and the plant Ozone definitely supports maintenance hygiene in the SPA The heated and ozonized Electric va air is pumped into the air duct system underneath the bath i O O
19. nofresh pH Tester pH measurement e rinse a test container and fill to the 10 ml mark with pool water e add 1 PHENOLRED tablet to the container and close the plug e shake the container and dissolve the tablet e compare the test water colour with the colours in the column on the left and read the pH of the water sample e all pH values below 6 8 make the water turn yellow e all pH values above 8 2 make the water turn red e ideal values range from 7 2 to 7 6 Dinofresh measurement This is a measurement of the active oxygen concentration contents informing about the oxygen content level in water e Rinse a test container and fill to the 10 ml mark with pool water e Add 1 DPD no 4 tablet to the container and close the plug e Shake the container and dissolve the tablet 14 e Compare the colour of the solution with the colours in the column on the right to read the Dinofresh value of the water sample e The recommended values range from 5 0 to 8 0 mg litre Important instructions e do not touch the tablets It may distort the test outcome e reading of results must take place immediately after the tablet has dissolved in water e after each measurement the test container and its lid should be thoroughly rinsed Otherwise it may also distort the results The tablet reagents are provided for the purpose of the above described chemical analyses and should not be used for any other purposes The tablet reagents must not
20. of grain 800 1200 2000 followed by the car polish mentioned earlier In order for the surface to be smooth it should be ground in a circular motion followed by a wax car polish which provides a high level of shine Repairs can be made with a repair kit available at the dealer shops however we recommend using the services of our authorized POOLSPA service staff 20 Before first use of spa please check whether all valves are open The repair kit for SPA baths GUARANTEE CONDITIONS Our company POOLSPA Sp z 0 0 guarantees its products against all manufacturing or operational defects under the conditions set out here After installing the Spa please fill with installer in manual the card with the details requested to ensure validity of warranty Please remember to get from sales agent confirmation of purchasing date 1 The product must be installed strictly in accordance with the installation instructions that come with the product and respecting all the measurements and indications given 2 For the warranty to be operative all work done during the warranty period must be carried out by a autho rised service The list of authorized service is available by Your sales agent 3 The warranty period POOLSPA Sp z o 0 provides a full guarantee for the Spa for a period of 2 years from the date of installation During this full guarantee period any manufacturing or operating defect will be repaired at no cost to the
21. rmed by an electrician with appropriate qualifications making sure the device is properly grounded 1 6 MASSAGE There are water and air massage systems installed in the bath 1 6 1 Hydromassage whirl bath Hydromassage is the pressure on defined muscles exerting by stream of water or stream of air and water Water or air and water at high pressure bring out from regulated jets and hit on body surface It tones and relaxes the skin at the same time massaging and cleaning it Hydromassage is recommended for anybody with spine arthritic or muscle pains respiratory system diseases or gynaecological problems Water massage system hydro massage is made of the following elements a set of 25 water and air jets supplying water or a water and air mix of high kinetic power to the water section of the bath a hydromassage whirl pump enforcing water circulation 2 regulators of air supply to the hydro massage jets installed at the edge of the bath used for regulation of massage intensity water suction point The water massage intensity regulation is possible by means of aeration regulators located at the perimeter of the bath top by adding air to the water stream coming from the jets The more air the stronger the stream is An accurate water massage power regulation can be also made by the jets what is described in detail in Part 1 2 Hydromassage intensity is increased by turning the regulator knobs anti clockwise
22. s flow related problems The problem with low flow persists this message appears after the message has been displayed five times within 24 hours The heater is switched off but the remaining spa functions work as usual Improper water quality low flow or air bubbles in the heater The spa is switched off for 15 minutes detected by the sensors This may indicate have been vented If the problem continues contact your DO NOT GO INTO THE WATER Remove the SPA cover and wait for the water to cool down Once the water is cooled reset the system by pressing any button If reset is not possible unplug the SPA and contact your local dealer or service center DO NOT GO INTO THE WATER Remove the SPA cover and wait for the water to cool down Once the temperature drops to 107 F 41 7 C the SPA should reset automatically If reset is not possible unplug the spa and contact your local dealer or service center If the problem persists contact your local dealer or the service centre This error may occur temporarily as a result of overheating If the problem cannot be solved contact your local dealer or service center This error may occur temporarily as a result of overheating If the problem continues contact your local dealer or service center If the water level is normal make sure that all pumps local dealer or service center Perform the steps which need to be taken when the message is displayed HFL Pre
23. ss any button to reactivate water heating If the water level is normal make sure all the pumps are primed The message will disappear automatically after 15 minutes The alarm is deactivated if any button is pressed manually If the problem continues contact your local dealer or service center Improper water quality has been detected Perform the steps which need to be taken when the in the heater this message appears after message is displayed dr The message will not be reset the message has been displayed three automatically The message is reset by pressing any times dr The spa is switched off button No action is necessary All devices will switch on regardless of the condition of the spa The devices remain on for 4 minutes after the sensors detect that the temperature has increased to 45 F 7 2 C or more An additional freeze sensor may be installed to protect the system from special conditions which may lead to its freezing Such a sensor is recommended for spas located in colder climate zones Contact your local dealer for more details Ice Conditions which may cause system freezing have been detected Caution Risk of electric shock The device does not include any parts to be fixed by the user Do not attempt to repair the control system yourself Contact your dealer or service center for help Follow all the user instructions on how to connect the spa to power supply Installation should be perfo
24. ssage pump from operating without water Any claims regarding a damaged pump operating without water will not be investigated 1 1 TECHNICAL SPECIFICATION SPA Victoria dimensions length 1765 mm depth 730 mm height 870 mm 20 mm 1580 1765 Capacity 800 Weight 275 kg without water and housing 988 10 550 _ 730 870 20 930 20 ea Dimensions shown in brackets apply to SPA with casing Dimensions of the SPA VICTORIA Material and construction Acrylic strengthened by laminated polyester on an aluminum frame SPAs with panels are installed on wooden frame only Voltage 230V 50 Hz 3N 400V 50 Hz option Electrical equipment 3 KW electric heater additional electric heater 3 kW option 1 5 kW hydromassage pump 1 2 KW axial blower Power cord 3 x 4 mm 5 x 4 mm version 3N 400V option Rated power and power consumption 5 7 KW 23 A version 230V 8 7 kW L1 13 A L2 13 A L3 9 A version 3N 400V Maximum number of people in the bath 4 Water The water should come from the water system and be properly purified and disinfected Well water is inadvisable unless it has special certificates in compliance with current norms 6 ANTIFROST System The main function of the bathtub controller is to maintain the preset water temperature within the range between 26 and 40 C Ho
25. ue ennen oaz cere ossee nes sept ase ocaeanes eee eae Kane 13 LAOS DiSIAFEE HOR ae rt nr acne eer eee nee eS ree eRe een ne Cee eae oe eee 14 1 11 Measurement and treatment formula Set ccccceccseeceeeeeeeeeeeeeeteeeteeseseteeeteeeeeteees 14 1 12 Thermal cover additional optional sescscnaccsceicessaecnenconssqaatseatetaceaateaoecminseianesesaseeearcageieaes 16 1 13 Disassembly assembly of Casing Optional ccccccccceccseeeceeeceeeseeeeeeeaeeeseeseesaues 16 PART 2 INSTALLATION MANUAL 2 LEAN SPORE FEE E E RCC ne eT Pe ee eee Te SAFE SI UNS 9 X 872 I AON HERE me RES ENE neon ne rte ene restr E eee eve Tee nn ae ee etn a ee 17 2537 BAN POSHO G aasaran r eee ener 17 2 4 Preparation of water and electrical connections u u ssssssssensesseseee senere kernen nn 17 2 9 Grounding cable Connec ON ae eo siecle AENDRE 18 AO CONNEC O AO MaS arera a a E A T E ae i ee 18 AT eO GNICE VAIVC oeste EE ISTERNINGER 19 2 8 Maintenance of acrylic ClEMENHS ccccccceecceeeceeeeceeeceeeceeeceueeseeeceeseueeaueesaeeseeesaeesaes 20 WARRANTY ROR OFA Taarn E EAA 21 TECAHNICACPRFRODUC T SAHER ee eee ee Roe A E 23 Introduction In order to be able to fully use all functions of a SPA Victoria please read all sections of this manual You should remember that despite the therapeutic and relaxing function of a hydromassage treatment seriously ill persons or persons suffering from heart disorder diseases or high blood pr
26. user excluding the bulbs If the product is installed in a country other than the country of acquisition the period and terms of the warranty will be restricted to the general warranty cover stipulated by regulations in the country concerned After 2 years from the date of installation POOLSPA Sp Z 0 0 provides post warranty payable service 4 The warranty will not be valid in these cases a a fault or faulty operation resulting from anomalies or non compliance with the product specific instala tion rules or arising in the hydraulic electrical or gas systems b corrosion scaling or abrasion caused by a lack of cleaning and or maintenance improper use creless storage or ill treatment breakages damage resulting from the use of water at temperatures of over 50 C wear from abnormal usage or any other cause not stemming from the appliance c if the Spa after use is not secured by thermal cover against sun radiance d if installation has been done by non authorised service or if non original spare parts were used e if it is found that the Spa has been in use for a period longer than the warranty period f if used water do not fulfill conditions of DIN 19643 97 as well SIA 173 5 In particular POOLSPA Sp z 0 0 declines all liability for any harm to people or damage to things that may have resulted from any of the excluded causes specified in the preceding section 6 Any other demand stemming from grounds not specified in the abov
27. wever the system features also a winter operation mode so called ANTIFROST to protect the piping from freezing The bathtub controller uses an integrated temperature sensor to control the ambient temperature in a continuous manner If the air temperature is lower than 7 2 C the winter mode is activated Turning the winter mode on involves activation of the entire electrical equipment of the bathtub pumps to prevent water from freezing in the spa Four minutes after the water has reached the temperature of 7 2 C the entire equipment is shut off and the ICE function is switched into stand by mode e Operation mode ANTIFROST system is marked by ICE symbol on the LCD screen e ANTIFROST mode is activated irrespective of the bathtub status If during filtration mode ANTIFROST system starts filtration mode will be switch off 1 2 JETS SPA VICTORIA is equipped with an innovative jet system ets _ _ Number __Phojg__ fixed mini jets A fixed mini ozone jet D large fixed directional jets B large rotary jets C All jets are controlled The hydromassage can be intensified by turning the jets in a clockwise direction about 90 and an anti clockwise direction decreases hydromassage intensity and eventually closes the jets Replacement of jet inserts with identical diameters The inserts can be unscrewed by a firm hand movement in an anti clockwise direction and then taken out of its frame Another prepared insert
28. y as for the a m 1 5 10 LOCKING THE PANEL Press the Time Blower and Warm buttons in that order within 3 seconds The panel will be locked To unlock it press the Time Blower and Cool buttons in that order within 2 seconds 1 5 11 BLOCKING TEMPERATURE CHANGES Press the Warm Time Blower and Warm buttons in that order within 3 seconds The Warm and Cold buttons will be locked To unblock temperature changes press the Time Blower and Cool buttons in that order within 2 seconds Diagnostic messages Message description Required action The control panel is inactive until the power is on The SPA settings remain unchanged until the spa is switched on again No message is displayed No power The pump must operate for 2 minutes before current Unknown temperature water temperature can be displayed Overheating SPA switched off A sensor indicates the heater temperature exceeded 118 F 47 8 C Overheating SPA switched off A sensor indicates the water temperature exceeded 110 F 43 5 C SPA switched off The sensor connected to the A sensor socket does not work SPA switched off The sensor connected to the B sensor socket does not work The sensors are out of balance If this message and the SPA water temperature are displayed alternately such a condition may be temporary If the situation persists the SPA will be turned off Significant water temperature difference i
Download Pdf Manuals
Related Search