SunRise Alarm Clock
Contents
1. symbol will show in the display When you program BEEP OFF the unit will beep once and the symbol will no longer be displayed Adjusting the Brightness of the Clock Display Press the PROGRAM button 5 times and the display reads DISPLAY AUTO the default setting Press the or buttons to change between DISPLAY AUTO and DISPLAY HIGH In DISPLAY AUTO mode the brightness of the display is automatically at a high level during the day but will switch to a lower level at nighttime so it does not disturb you while sleeping The display will dim in this mode as the light dims down when either the alarm has been set and the ALARM button is OUT on or you have activated the sunset mode both indicating you are preparing to go to sleep When DISPLAY HIGH is selected the display will always remain in the bright mode Activating the Alarm After you have set the time you wish the alarm to go off the next morning push ALARM button so it is OUT on The display will show the Alarm Set sun symbol XY and the Alarm Time you chose will be displayed for a few seconds If the light is on when you enable the alarm it will slowly fade out or you can turn it off right away by pressing and holding the button until the light is out WAKE UP SEQUENCE The SunRise Wake Up Sequence The light will gradually begin to illuminate before your set wake up time Once the light has fully illuminated and the SunRise wake up time has been reached th2. e As with any electrical product do not immerse the clock wire in water e Never use a bulb with greater than 60 Watts maximum e There are no user serviceable parts Please do not open the case Service If your SunRise Clock is not operating properly contact BioBrite directly for customer service warranty repairs and out of warranty repairs by e mail at BioBrite aol com or calling 301 961 5940 Please contact us before sending anything in because many times problems can be solved by Customer Service Replacing the Bulb Your BioBrite clock uses a standard 60 Watt bulb with a Candelabra E12 base Special bulbs that produce more light are available through BioBrite To replace the bulb 1 Unplug the clock from the wall 2 Remove the glass globe from the clock by pulling firmly upward Remove the globe by holding the base with one hand and pulling up on the glass globe with the other hand Display Reference Guide lt 4 ALARM SET sun symbol 3 Unscrew the bulb Caution If the bulb was recently in use it will be hot let the lamp cool before removing the bulb 4 Screw in the new bulb completely Carefully put the globe back on by lowering over the bulb and making sure it catches on the latches in the base 5 Plug in the SunRise clock re set the time and re set your preferences BEEP ON sound symbol PM After midday symbol NOTE If the display is too dim to see easily press the ALARM button IN and the dis
3. WARRANTY FORM TM CHARCOAL SUNRISE CLOCK Model 88630 082010 Your SunRise Clock warranty expressly covers any defect in manufacture for 12 months from the date of purchase In order for the warranty to be valid please fill out and return a copy of this warranty form with a copy of your receipt NAME ADDRESS PHONE PLACE PURCHASED DATE PURCHASED COMMENTS BioBrite Inc 4330 East West Highway Suite 310 Bethesda MD 20814 301 961 5940 E mail BioBrite aol com Website www BioBrite com Instructions for the BioBrite SunRise Alarm Clock Charcoal Programmable Model BioBrite Inc 4330 East West Highway Suite 310 Bethesda MD 20814 301 961 5940 E mail BioBrite aol com Website www BioBrite com The SunRise Clock is a great way to wake up feeling more refreshed and ready to go Humans are naturally adapted to wake to the rising sun and sleep at sunset So waking up to a simulated sunrise can give your body a gentle and natural boost in the morning Please take a few moments to read the directions to ensure you get off to a good start with your SunRise Clock Setting Up the SunRise Clock For best results Set the clock near your bed on a nightstand or bedside table close to pillow level plug the clock into a wall outlet do not use surge protectors or long extension cords unless they have 3 prongs in the plug and are heavy duty NOTE Until time has been set or after a prolonged power
4. e audible alarm will sound The audible alarm begins with a quiet beep and gradually intensifies to full volume over 30 seconds 3 Setting the Speed of the SunRise Wake Up The SunRise Clock is preset for a 30 minute wake up sequence 1 e the light will reach full brightness gradually over 30 minutes If you wish to change the SunRise time you can choose between 15 30 60 and 90 minutes Press the P button 6 times until the display reads FADEUP followed by a number Press the or button to alternate between FADEUP DEMO see Additional Features FADEUP 30 30 minute sunrise this is the default FADEUP 60 60 minutes FADEUP 90 90 minutes and FADEUP 15 15 minutes Using the Snooze Feature To temporarily snooze the alarm press the minus button while the alarm is beeping The beeper will stop sounding and go off again in 9 minutes If you would also like the sunrise to begin again then continue pressing the minus button until the light has gone all the way off Over the next 9 minutes the light will gradually brighten this will occur at a quicker rate than the originally programmed SunRise time and finally the beeper will sound again Turning off the Alarm Once Awoken After you wake up if you want to turn off the alarm push the ALARM button IN off The beeping will stop but the light will remain illuminated until you shut it off If the alarm is not turned off manually the beeper and light will both auto
5. enu automatically and go back to displaying the time Programming Table Presses First setting in bold is the default e rameur azos oewos e imeoza o secuen omr secur ON Programming settings are memorized by the clock so if the power goes out or the clock is unplugged for a few minutes you will not need to reset the clock Setting the Wake Up Alarm Time Press the PROGRAM P button once so the display reads ALARM TIME Then adjust the alarm time with and buttons until desired time is set Holding in the or button will cause the time to change rapidly Setting the Time Press the PROGRAM P button twice The display should read TIME Then use the and buttons to adjust the time The time moves rapidly if the or button is held in Setting a 12 or 24 Hour Display Mode The clock is defaulted to a 12 hour display To change to a 24 hour display mode press the PROGRAM button 3 times Then press the or button The display will alternate between 24 HOUR and 12 HOUR The PM symbol on the time display is only present in the 12 hour mode Enabling or Disabling the Beeper The beeper shown as the symbol is set ON at the factory To disable the audible beeper that sounds at the end of the wake up sequence press the PROGRAM button 4 times until the display reads BEEP ON or BEEP OFF Then press the or button to alternate between the two When you program BEEP ON the beep will sound twice and the
6. ile pressing the button Likewise if you have the light on and would like to demonstrate the sunset feature press the ALARM button IN off then press it OUT on The clock will dim out over the next 100 seconds Troubleshooting Problem The light will not come on but the clock still works Solution The bulb may be burned out Look at the bulb and see if the filament is broken If it is replace the bulb Also check to be sure the bulb is fully screwed into the socket Problem Neither the light nor the clock works Solution Unplug the clock from the wall for several seconds and re plug it in while holding in the PROGRAM button Doing this will reset the clock and have all the default settings restored Sometimes the clock s computer chip picks up static charges of electricity and unplugging it removes the static Programming the Clock Press the PROGRAM P button to enter the clock s menu and change any of the clock settings NOTE The menu is not accessible if the ALARM B button is up on so always make sure the ALARM button is IN off when you want to program the clock The text display below the time digits will show the setting you are changing and what the current status is Change the setting using the PLUS button and MINUS button Once you have completed a setting you can press the PROGRAM P button again to adjust another setting or simply wait for approximately 12 seconds and the clock will exit the m
7. matically shut off after about fifteen minutes SUNSET SEQUENCE Activating the Sunset Sequence Manually turn the light on to the intensity from which you wish the sunset to start If the Alarm button is pushed IN off push it again so that it is OUT on This will begin the sunset NOTE If you wish to activate the sunset without activating the sunrise for the following morning then make sure the ALARM button is IN off Then press both the and buttons simultaneously to begin the sunset Setting the Speed of the Sunset Sequence Press the P button 7 times until the display reads FADEDOWN followed by a number Press the or button to alternate between FADEDOWNIS5S 15 minute sunset FADEDOWN30 30 minutes this is the default FADEDOWN60 60 minutes and FADEDOWN90 90 minutes Once the desired sunrise length is displayed do not push any buttons and the clock will return to its time setting in 12 seconds Setting the Sunset Sequence to End as Nightlight In the sunset mode you can have the light stop dimming when it reaches approximately 5 intensity for use as a nightlight Press the PROGRAM button 8 times until the display reads NITELITE OFF or NITELITE ON Then press the or buttons to activate or deactivate the nightlight 4
8. outage the digits on the clock will flash on and off Before doing anything you should familiarize yourself with the clock control buttons The PROGRAM button labeled P is used to change all the settings The words below the time display will show you what setting you are changing and what the current setting is To adjust any setting make sure the ALARM button A is pressed IN off so that the symbol for the sun is not lit Press the PROGRAM button a number of times then within the next few seconds change the setting by pressing the or button After you have programmed all the settings the way you want them simply wait for 12 seconds and the display will return to the time mode Button Reference Guide P PROGRAM button Programs time and other settings MINUS button Dims light and changes settings PLUS button Brightens light and changes settings A ALARM button Activates alarm on or off IMPORTANT SAFETY INSTRUCTIONS e The clock has a polarized plug one prong is wider than the other which will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug Most uninterruptable power supplies and some surge protectors will not work with the clock If an extension cord must be used it should have 3 prongs and be heavy duty Do not alter the plug e Never remove the glass globe while the lamp is or has recently been operating The bulb and globe can be extremely hot
9. play will become bright READING LAMP Using the Adjustable Reading Light Again make sure the ALARM A button is pressed IN off then press the button to turn on the lamp and to increase brightness To reduce the light level press the button Holding in either button adjusts the light level rapidly ADDITIONAL FEATURES Activating the Security Mode This mode is useful when you are away on vacation or your house is empty and you wish to give the appearance that someone is there To turn on the Security Mode press the PROGRAM button 9 times so the display reads SECURITY OFF Press the or button and the display will switch to SECURITY ON indicating that the security mode is activated During the security mode the clock will come on and off randomly between 4 p m and 11 p m When this function is set and you ve exited the programming mode the main display will read SECURITY To exit the security mode upon your return push any button and SECURITY should no longer be displayed Using the Demonstration Mode To set or cancel the Demo Mode see the section headed Setting the Speed of the SunRise Wake Up Once activated the display should read DEMO MODE This sets the clock into high speed demonstration mode so you can show it to a friend without having to wait 30 minutes for the full cycle To create a speedy sunrise to occur over the next 100 seconds push the ALARM button OUT on then hold the PROGRAM button in wh
Download Pdf Manuals
Related Search