Six-defense zone Display Alarm System
Contents
1. we often start this function Once starting this option the signal from remote control is screened and only the keypad in the control panel can arm the system Command Start 18 1 Close 18 0 9 Start close the reminder for phone line trouble It will tell you when the phone line is cut or short It will sound beep three times every 10s Command Start 22 17 Close 22 0 10 Setup the times of ring You can setup the times of ring by calling the Host phone number Command 12 XX XX shows times of ring from 00 12 00 means ring is closed In that case the system cannot dial out phone numbers when there is an alarm 11 Setup the time of siren You can setup the siren to make it last 5 minutes 10 minutes or 30 mins Command 29 XX XX 15 00 30minutes 13 Reset You can delete all registered information including passwords in order to return the original status before living factory Command 0000 How to control the control unit with remote controllers VI Instruction of Use 1 Out Arm Press A or keep pressing the key OUT with the status LED flashing the system will enter into the mode of Out Arm The system will enter into the mode of Out Arm if you press the key A and continue to press A 2 2 Home Arm Press A or keep pressing Home for 2 seconds with the sound beep the status Led flashing the system will enter into the mode of Home Arm In this worki2. a Insert the siren to the port of control panel and connect telephone line with the port of input and output with the telephone set That is to say the telephone must be connected with control panel The telephone can work normally b Power the system on and switch it to ON the power status will be blinking and sound beep which shows the control panel works normally It will sound three beep beep beep every 30 seconds which helps users remind of setting alarm phone numbers The sound beep will disappear when you finish the alarm phone number setting Please press e to make the system disarmed to avoid it activate the siren to alarm when registering sensors Attention a Try to install the control unit in the center of defense zone and pull antenna and make it up for getting more wireless receiving distance b Installation position should be far away with huge metal objects and wireless device Connect the trunk line with control panel in order that it can dial out in the first second when there is an alarm Should be installed in a shelter II Installation of door sensors Door sensors are used for detecting the status of open and close of windows and doors It will detect it and send the signal to control panel Fix the transmitter box and magnet to door case and door You d better fix it again with bolt if you want it fixed strongly Caution A Magnet should be close to signal status and make the
3. into the mode of 30 seconds of listen in Press to exist Note The system will hang off automatically 1f passwords are wrong for 3 times or no any order in 20 seconds Use of remote controller l Arming button press it to arm system Siren will have a short ring 2 Disarm button press it to disarm system Siren will 3 help lsarm Arm have two short rings 3 Panic button press it and siren will start to ring 000000 continuously alarming the others The following sensors can be optional Additional wireless products M Q Panic Buttons PIR Detectors Smoke Detectors Door Window Remote Controls LPG Gas Detectors gap sensors Optional sensors detectors are packed separately It includes remote controllers wireless PIR wireless gap sensor wireless gas detector wireless smoke detector panic button baluster according your specific needs Typical house configuration ik s s i gt IT 5 4 I F rr i B A j ri 5 i a p i I i i a Door window p PP Garage 4 i I p oj Pi Art pF ry gi 7 i I r s i m i M f F i z Fi s E EE I A d Fl a iii po z e ri Fi E z g dd tu H i tee oe z F T if a a DN bd af P Ps QU waka A SS make PIR Movement Detector Detectors Explanation of alarm systems 1 Working elements An alarm system contain
4. Six defense zone Display Alarm System User Manual Feature 1 10 11 L2 Anti interfere function When someone interferes it with same frequency the control unit will activate siren to alarm Support anti decode with remote control 6 programmable Defense zone available with status LED The control panel can register 99 sensors and detectors Every defense zone can set independently arm disarm delay alarm and SO On Have the function of one key arm User can start Home arm or Out arm freely by keeping pressing one key on remote control Can set the reminder sound of defense zones Will remind users of remembering arm the alarm system when going out Can work with other products of our company Such as wireless big outdoor siren and mini siren and YL 007AS It stores 2 groups of monitoring center and 6 groups of user phone numbers to dial out and play the recorded message if there 1s an alarm Can arm disarm with remote control or keypad on the control panel Can arm disarm listen in by calling the host phone number The phone numbers of control panel Have the function of reminder for circuitry failure For example if telephone line 1s cut or short the control panel will alarm Have the superior of connection Have in built backup battery and can continue to work and last for 8 10 hours when electricity 1s cut or in failure How Do I install the alarm system I Installation of Control unit
5. anel can identify them when they send signal to control panel Standard pack components 1 the alarm system I wireless infrared detector I wireless door magnet detector 1 internal alarm sounder 2 remote controllers 1 12v de power supply 1 instruction manual Technical Parameters Operating voltage DC6V Average power AC DC exchanger 2A Wireless receiving distance 100m Operating Frequency 315MHZ or 433 92 900 1800MHZ Customized Operating voltage 12V 220 110VAC Wireless receiving distance 2 100m 250m Outer Alarm Siren Volume 110 db Working Condition Temperature 10 C 40 C Humidity lt 90 Capacity for Wireless Device 32 Wireless Gap Detector Power Supply DC12V inner 12V battery Static Current lt 20 uA Transmission Current S15mA Transmission Frequency 315 433MHZ 0 5MHZ Transmission Distance No obstacle 80m Interval Distance 15 mm Working Condition Temperature 10 C 40 C Humidity lt 90 Wireless P IR Detector Power Supply DC9V inner 9V battery Static Current lt 100 uA Transmission Current lt 20mA Transmission Frequency 315 433MHZ 0 5MHZ Transmission Distance No obstacle 80m Detective Speed 0 3 3m s Detective Distance 5 12m Detective Range Horizontal 110 Vertical 60 Working Condition Temperature 10C 40 C Humidity lt 90 Remote Controller Power Supply DC12V inner DC12V battery Static Current 0 Transmission Current S15mA T
6. egistering please enter to exist two beeps 4 How to delete all coded information if you want to recheck in Under the status of registering please input 7 It will sound beep beep two times all coded information has been deleted IV How Can I setup the Alarm Phone Numbers The phone Nos that will be dialed out when there is an alarm Command 31 the Ist User phone number 32 the 2nd User phone number 33 the 3rd User phone number 34 the 4th User phone number 35 the 5th User phone number 36 the 6th User phone number 38 the Ist phone number of monitoring center 39 the 2nd phone number of monitoring center Note Do not setup the last monitoring center numbers if you do not have monitoring center You can enter a blank order if you want to delete a Alarm Phone Number Fox example You want delete the 4 Alarm Phone Number only input 34 Operation sketch Input password default 1234 Alarm Phone No Settings Sensors Register Record Voice Message 31 the 1st User phone number 32 the 2nd FE phone number 33 the 3rd User phone number 34 the 4th User phone number 35 the 5th Sag phone number 36 the 6th User phone number 38 the Ist phone number of Record Replay Delete all stored Register message The Sensors message with inform ation control b monitoring center 39 the 2nd ph
7. ial out users phone numbers in the status of Home Arm 0 for Closed Zone It is closed temporarily and is used for arming in sub defense zone E g If you want the second defense zone to be inner zone You can input 0225 Reminder for application Usually we setup the door window sensors installed in windows veranda and doors as Immediate Zone The detectors in this area will activate alarm in any mode of arming If you setup wireless PIR detectors as the Inner Zone they will work in the mode of Out Arm but do not work in the mode of Home Arm You can setup the doors in the main gates as Delay Zone if you do not want to take remote control when going out In this case you can disarm the system within 30 seconds after opening the door but the alarm system will not have enough time to activate siren and dial out alarm phone numbers 6 Start close reminder for defense zone If you start the reminder for defense zone it will beep beep beep for three times to remind users of arming Command Start Zone No 71 Close Zone No 70 7 Start close the function of anti interfere When starting the function of anti interfere in arming status it will activate siren to alarm not calling users 1f someone interferes the alarm system with same frequency Command Start 17 1 Close 17 0 8 Start close the function of anti decode In order to Prevent someone from decoding the alarm system
8. ng mode the detectors in Inner Defense will not work 3 Disarm Press du on remote control or input password DISARM on control panel the system will disarm 4 Emergency Help SOS Meeting urgent incident you can press AD on remote control or pressing the key PANIC Note Please wait 10 seconds or so repress disarm and enter into next operation It needs time to be activated again 5 The process of receiving an alarm What should I do when I receiving the phone call from the alarm system When detecting something unwonted the detectors will activate the siren and dial out alarm phone numbers and the status LED will be on User can answer the phone and do it according the following steps Press to start the function of listen in for 30 seconds you will hear what is happening around the alarm system Press to confirm that you have already received the signal of alarm and stop alarm If you do not input the alarm system will continue to dial out all alarm phone numbers circularly 6 Remote control You can call the host phone number to control the system to make them arm or disarm by input passwords If the password is correct the system will sound beep two times If wrong it sounds beep four times And then you can control the system with following command Press 1 to arm Make sensors working Press 2 to disarm make sensors stop working Press to enter
9. one number of panel monitoring center There are six defense zones so you can install sensors in any of defense zone You will know what sensors are triggered from the screen of control panel You can input 02 and then trigger sensors and then enter into the next defense zone Enter 7 and trigger sensors Zone 2 Enter 02 and trigger sensors Zone 3 Enter 03 and Zone 4 Enter 04 and trigger sensors V How to Modify passwords Command 10 passwords passwords must be digitals This password is used for remote control Users should setup it confidently ek The following options can be used for special operations Users who do not connect the alarm system with monitoring center do not have to read tt VI Defense Zone Setting You can setup your sensors or detectors into a special defense zone which can make some detectors not work when there is an alarm Command Zone No 2 X X will be 1 for Immediate Zone It can activate the siren and order the control panel to dial out Alarm phones immediately if the detectors in this defense zone detect some unwonted Status 2 for Delay Zone Activate siren and dial out in 30 seconds when detectors in this zone find something unwonted 3 for Urgent Zone It will activate siren and dial out users phone numbers no matter it is arming or disarming when the detectors in this defense zone are triggered 5 for Inner Zone It will not activate siren and d
10. ransmission Frequency 315 433MHZ 0 5MHZ Transmission Distance No obstacle 80m Working Condition Temperature 10 C 40 C Humidity lt 90
11. s two parts a control panel and some sensors When sensors detect unwonted situation they will send signal to control panel When control panel receives the signal it will activate siren to make 110dB sound to inform people around and dial out preset phone numbers for help Control Panel Send signal to the control panel PIR Detectors Door Window Contacts LPG Gas Detector Remote Controls 2 Function of each sensors detectors and control panel Sensors detectors include Door window contacts sensor PIR Sensor detectors and smoke gas detectors remote controls 1 Window door sensors are used to induct the close and open of doors or windows If a door is opened it will send signal to control panel 2 PIR Sensors detect the motioning object with infrared activities 3 Smoke gas detectors detect smoke or gas leak When detecting smoke or gas it will send signal to control panel 4 Control panel like a brain of the alarm system It will activate siren to make 110dB sound to attract attention from people pass by and auto dial preset phone numbers to call police and owners 5 Siren To make 110 dB sounds 3 We sell at a standard package Customers can add more sensors detectors if needed 4 Wireless sensors do not need wire to communicate with control panel They use wireless communication so wireless sensors detectors have to be registered with control panel before working so that control p
12. t detects unwonted status it will send signal to control panel If it did not register with control unit the control unit would not identify 1t and could not receive the signal so the alarm will be failed Before registering please input 7 with a beep the arm status flashing it shows on the status of registering Now you can start to register sensors Please collect all detectors including door sensors PIR detectors and gas smoke detectors together with the control panel and make sure their battery inside and can work normally Switch on control panel power LED is on and trigger the sensors or detectors you are going to check in 3 How to trigger sensors or detectors When the control panel is powered start to register them For door sensors just remove the two parts of door sensor and remove back it will beep and the status LED flashes which shows successful And for PIR Sensors you can turn the switch to on and the system will beep which shows successful and then turn it to off to avoid wrong alarm For remote controllers you can press any key on its panel three keys on it and the system also beeps For gas and smoke detectors there is a black switch on the left side you can press it to register it with control unit For break sensor you can put it on a desk and then shake the desk it will send a signal to control panel The control panel will response with a beep sound which shows successful After finishing r
13. transmitter box and magnet as close as possible lt 10mm B In order to get the best receiving distance you should pull the antenna and make it upwards C If the indicator light of door sensor are still blinking 1t shows battery fails So please replace it as soon as possible III Installation of Wireless PIR motion Sensors PIR Sensors are used for detecting if someone moves within in a certain place Fix it on the wall 2 2 2meters high and you should adjust the position to make it face to the defense zone Caution How Can I set up the alarm system Before any operation please enter passwords and Default is 1234 Two beeps show that the operation is successful four short beeps shows fails You have to try again in this case Please press to exist the programmed status System will exist automatically if there is no any order within 30 seconds 1 Record alarm message Input 6 to record message within in 10 seconds and you will hear a beep It will exist with two beeps automatically after 10 seconds Every recorded message will replace the last message The message should be short and clear For example This is xxxxx building and room xxx please come to offer help Play the recorded message please press 6 2 How do I Register sensors or detectors with control unit First as we all know every detector has its unique ID It must be registered with the control unit so that it can be identified during working When i
Download Pdf Manuals
Related Search