41-920 Remote Instructions
Contents
1. lt gt SERVODAN White buttons Used by the user on a daily basis JO Lux zone 1 Grey buttons Used only upon first startup Red buttons Used only upon startup for setting Lux in zone 1 4 Orange button Used only upon startup for setting Lux in zone 2 factor of Lux zone 1 only 41 445 5 Blue button Used only upon startup for setting off delay of movement sensor Pushbutton door e Movement sensor ef Luminaire Smartscape Automation Ph 07 3357 1922 info ssqid com au www ssqid com au lt gt SERVODAN SNS User guide CGB IR Remote Control 41 9020 This setting Learn actual lux should be used when the desired minimum lighting in the room has been reached the time when the light will be switched on due to insufficient daylight in the room Lux Zone 2 Not used in connection with PIR model 41 400 Time Setting the cut out time There are six preset settings 2 5 10 15 and 30 minutes as well as Pulse 5 seconds On 60 seconds Off Time 1 Time 2 Time 3 are not used for this product Test On Off Activating walk test If the test is off and the button is pressed the green LED will flash and the red LED will come on for 2 seconds If the test is On and the button is pressed the green LED will flash for 2 seconds Lux On Off Operation Setting daylight dependency Only works for App 1 2 The IR Remote Control 41 920 is used for setting v2. made green LED goes out See installation and user manual for PIR Sensor model 41 400 For all settings except Light 1 On Off the movement sensor must be unlocked the setting selected and the movement sensor locked again before the setting is activated If the movement sensor is not locked it will lock automatically after 5 Light 2 On Off Not used in connection with PIR model 41 400 LED On Off minutes and any modified settings will be saved Switches the red LED on off to indicate movement If the LED is off and the button is pressed the green LED will Light 1 On Off flash and the red LED will come on for 2 seconds Has the same function as a long manual press and switches If the LED is on and the button is pressed the green LED will flash onthe light in Zone 1 Can be used without first pressing Lock for 2 seconds Unlock See installation and user manual for PIR Sensor model 41 445 Lux Zone 1 Setting the lux level There are six preset settings 30 100 300 600 Light 2 On Off 1000 and 2000 as well as user defined lux value Learn actual lux Has the same function as a long manual press and switches The user defined lux value works in the 5 2000 lux range on the light in Zone 2 Can be used without first pressing Lock When the Learn actual lux button is pressed the green LED Unlock flashes for 10 seconds as an indication that the lux level is See installation and user manual for PIR Sensor model 41 445 being loaded Th
3. the white button on the IR Remote is as follows Light 1 On Off Has the same function as a long manual press and switches on the light The light can be switched off by means of a short press of the wall switch or by pressing the Reset button on the IR Remote Glossary Movement sensor Sensor that is installed in the ceiling where it registers activity in the room and thus keeps the light switched on Cut off time The cut off time is the time that passes between the movement sensor having registered its last movement until the light is switched off info ssqld com au www ssqid com au lt gt SERVODAN Daily user manual CGB IR Remote Control 41 920 Together with PIR Sensor 41 445 On a day to day basis only the two white buttons and possibly the Reset button should be used and if necessary a normal switch on the wall The unit to be controlled can run with two settings One is known as automatic on where the light comes on automatically when someone walks into the room and the other is known as manual on where the light must be switched on manually using the wall switch Note The range of 41 920 to the sensor is approx 3 m The wall switch has two functions One short press and one long press Short press A short press is a press lasting less than one second If the light is on in one of the zones it will turn off and the movement sensor will be blocked for 10 seconds The moveme
4. arious If the movement sensor is daylight dependent and the button is parameters for PIR Sensor models 41 400 and 41 445 pressed the green LED will flash for 2 seconds Note The range of 41 920 to the sensors is approx 3 m If the movement sensor is daylight independent and the button is pressed the green LED will flash and the red LED will come on Reset Pressing this button restores all settings to factory settings Function with 41 400 For further information see the installation and user manual for Lock Unlock PIR Sensor model 41 400 Press to unlock the movement sensor unlock so that the settings can be modified the green LED on the movement sensor comes on Press again to lock the movement sensor lock after the Function settings have been made green LED goes out For all settings except Light 1 On Off the movement sensor gt _ must be unlocked the setting selected and the movement sensor Function with 41 445 locked again before the setting is activated If the movement sensor is not locked it will lock automatically after 5 minutes and Lock Unlock any modified settings will be saved Press to unlock the movement sensor unlock so that the settings can be modified the green LED on the movement Light 1 On Off sensor comes on Has the same function as a long manual press Press again to lock the movement sensor lock after the Used without pressing Lock Unlock first settings have been
5. conds If the movement sensor is daylight independent and the button is pressed the green LED will flash and the red LED will come on for 2 seconds Reset Under unlock Pressing this button restores all settings to factory settings Under lock All outputs are turned off The sensor will now switch on the light according to the selected App For further information see the installation and user manual for PIR Sensor model 41 445 Smartscape Automation Ph 07 3357 1922 App Application describes the function of the sensor Zones 1 and 2 How the room is divided see Fig 2 Lux Zone 1 and 2 Lux level where light is desired in zones 1 2 Off delay Cut off time before movement sensor switches off the light Cut off Cuts off 230 V to zones 1 2 due to lux level Explanation Fig 1 1 White buttons used by the user on a daily basis 2 Grey buttons only used upon first startup 3 Red buttons only used upon startup for setting Lux in zone 1 4 Orange buttons only used upon startup for setting Lux in zone 2 factor of Lux zone 1 only 41 445 5 Blue buttons only used upon startup for setting cut off time for movement sensor Factory settings 41 400 Sensitivity High sensitivity Application App 1 Lux 100 lux Time off delay 10 mins LED movement indication Off can only be changed via the remote control Factory settings 41 445 Sensitivity High sensiti
6. d this is indicated on the movement sensor by the red LED flashing 1 second On and 3 seconds Off Function of the two white buttons on the IR Remote is as follows Light 1 On Off Has the same function as the long press but only switches on the light in Zone 1 Light 2 On Off Has the same function as the long press but only switches on the light in Zone 2 Glossary Movement sensor Sensor that is installed in the ceiling where it registers activity in the room and thus keeps the light switched on Cut off time The cut off time is the time from when the movement sensor registers the last movement until the light switches off Zones Fig 1 The room is divided into two zones There will typically be one zone by the windows and one zone away from the windows When the light is daylight regulated the zone by the windows will typically be dimmer possibly switched off than the other zone info ssqld com au www ssqid com au
7. en the green LED comes on and the connected lighting is turned on for 5 seconds When Lights 1 and 2 On Off are activated the low voltage relay If the lux level is outside the 5 2000 lux range this is indicated by is also activated 08 9 on 41 981 The low voltage relay will the green LED flashing quickly It will continue to do this until one be activated On as long as activity is registered and the cut off of the preset settings is selected time 2 hours have not elapsed Smartscape Automation Ph 07 3357 1922 info ssqid com au www ssqid com au lt gt SERVODAN LED On Off Switches the red LED on off to indicate movement If the LED is off and the button is pressed the green LED will flash and the red LED will come on for 2 seconds If the LED is on and the button is pressed the green LED will flash for 2 seconds Lux Zone 1 Setting the lux level There are six preset settings 30 100 300 600 1 000 and 2 000 as well as user defined lux value Learn actual lux The user defined lux value works in the 30 2000 lux range When the Learn actual lux button is pressed the green LED flashes for 10 seconds as an indication that the lux level is being loaded Then the green LED comes on and the connected lighting is turned on for 5 seconds If the lux level is outside the 30 2000 lux range this is indicated by the green LED flashing quickly It will continue to do this until one of the preset settings is selected This s
8. etting Learn actual lux should be used when the desired minimum lighting in the room has been reached the time when the light will be switched on due to insufficient daylight in the room The lights will go out when the room has been over illuminated for 5 minutes Cut off Lux Zone 2 Settings for Lux zone 2 are made as a factor of zone 1 If for example 300 Lux has been selected for zone 1 and factor 0 6 is chosen zone 2 will be switched on when the light level falls below 180 Lux The lights will go out when the room has been over illuminated for 5 minutes Cut off Time Setting the cut off time for PIR off delay the two zones Time 1 Zone 1 and Time 2 Zone 2 and the low voltage relay Time 3 There are six preset settings 2 5 10 15 and 30 minutes as well as Pulse Pulse in conjunction with Time 3 5 seconds On 60 seconds Off In conjunction with Time 1 and 2 1 minute cut off time To set the time first press Time 1 2 or 3 depending on the zone to be set followed by the desired time Test On Off Activating walk test If the test is off and the button is pressed the green LED will flash and the red LED will come on for 2 seconds If the test is On and the button is pressed the green LED will flash for 2 seconds Lux On Off Setting daylight dependency Only works for App 1 2 If the movement sensor is daylight dependent and the button is pressed the green LED will flash for 2 se
9. itched off and the movement sensor will be disabled for 10 seconds The movement sensor then switches to automatic mode and the light will turn on according to the selected application If the light is off the light will switch on and the movement sensor will keep it on as long as movement is registered and the cut out time has not elapsed Always according to the selected application Long press A long press is a press lasting more than one second and is daylight independent If the light is on the light will switch off and the movement sensor will be disabled as long as movement is registered and the cut out time 2 hours have not elapsed The movement sensor then Smartscape Automation Ph 07 3357 1922 switches to automatic mode and the light will turn on according to the selected application For example The time has been set to 15 minutes so the movement sensor will switch to automatic mode 2 hours and 15 minutes after it last detected activity If the light is off the light will switch on regardless of light levels and the movement sensor will keep it on as long as movement is registered and the cut out time 2 hours have not elapsed The light then turns off the movement sensor switches to automatic mode and the light turns on according to the selected application If a long press is activated this is indicated on the movement sensor by the red LED flashing 1 second On and 3 seconds Off Function of
10. nt sensor then switches to automatic and the light will only come on according to the setting selected automatic or manual on If the light is off in one of the zones it will turn on and the movement sensor keeps it turned on as long as activity is registered and the cut off time has not elapsed Always according to the selected setting Long press A long press is a press lasting more than one second and is daylight independent If the light is on in one of the zones it will switch off and the movement sensor will be blocked as long as activity is registered and the cut off time 2 hours have not elapsed The movement sensor then switches to automatic and the light will only come on according to the setting selected automatic or manual on Smartscape Automation Ph 07 3357 1922 6 Pushbutton door e Movement sensor ns Luminaire For example The time has been set to 15 minutes so the movement sensor will switch to automatic mode 2 hours and 15 minutes after it last detected activity If the light is off in one of the zones it will turn on regardless of the light level and the movement sensor keeps it turned on as long as activity is registered and the cut off time 2 hours has not run out The light is then switched off the movement sensor switches to automatic and the light will only come on according to the setting selected automatic or manual on If a long press is activate
11. vity Application App 1 Lux Zone 1 100 lux Lux Zone 2 Factor 0 8 80 lux Time 1 Off delay zone 1 10 mins Time 2 and 3 Off delay zone 2 and relay 8 9 10 mins Cut off 5 minutes cannot be changed LED movement indication Off can only be changed via the remote control DIP switch setting 41 440 and 41 445 0 Off and 1 On Sensitivity on DIP 1 and 2 DIP setting Sensitivity 00 Minimum sensitivity 0 1 Low sensitivity 10 High sensitivity Default 11 Maximum sensitivity Application on DIP 3 and 4 DIP setting App 00 App Auto Default 01 App Manual 10 App Auto without light sensor 11 App Manual without light sensor info ssqid com au www ssqid com au OERVODAN Daily user manual IR Remote Control 41 920 Together with PIR Sensor 41 400 On a day to day basis only one white button and possibly the Reset button should be used and if necessary a normal switch on the wall The unit to be controlled can run with two settings One is known as automatic on where the light comes on automatically when someone walks into the room and the other is known as manual on where the light must be switched on manually using the wall switch Note The range of 41 920 to the sensor is approx 3 m The wall switch has two functions One short press and one long press Short press A short press is a press lasting less than one second If the light is switched on the light will be sw
Download Pdf Manuals
Related Search