INSTRUCTION MANUAL
Contents
1. Free 877 269 8490 00 05 with burst shot of 3P this means the camera will keep taking burst shots of 3 pictures for every 5 seconds within time interval of 8AM to 8 30PM Out of the time lapse time said 20 30 to 08 00 the camera will sleep no matter of activity level NO capture at all If a user selected the Time lapse mode and set the start time from 00 00 and end time at 00 00 and then selected the timeout to be 05 00 with a burst shot of 3P this means the camera will keep taking burst shot of 3 pictures for every 5 min 24 hours non stop TIME LAPSE SETUP RECOMMENDATIONS We recommend that if your using the Time Lapse feature and what to extend your battery life and get the most pictures possible use the following settings Batteries Energizer Lithium Batteries Resolution Base 1 Star 1 3Mp Time Out 20 seconds WWW STEALTHCAM COM 26 Toll Free 877 269 8490 USING THE CAMERA Once all program settings have been setup properly your Stealth Cam is ready for field use Getting started Listed below are some helpful pointers on how to use your camera to get the best results Mount the camera about 4 5 feet high with the camera pointed at a slight downward angle Mount the camera facing north or south NOT east or west due to the rising and setting of the sun could produce false triggers and overexposed images If you re covering a trail face the camera down or up the trail Most commercial cameras take 1 3 seco2. If no SD card is inserted the front counter display will show NOSd WARNING The above camera will not accept any High Speed memory cards Common verbiage that will indicate High Speed includes but is not limited to Extreme Ultra Optima Micro Platinum Store and Shoot WWW STEALTHCAM COM 12 Toll Free 877 269 8490 Inserting SD memory card NOTE Make sure camera is in the OFF position whenever adding or removing memory Insert SD memory in to the SD card slot completely and the correct direction as shown by the sticker located at the side of the housing To remove the SD memory card depress the SD card and pull out the card gently 50 cards must be clean no images from other sources If you are using the SD card from other cameras please make sure to format the SD card in your computer prior to use in your camera New cards are good to use straight from the package FORMAT Definition When you format a SD memory card the operating system erases all information and files on the card Then it creates an internal address tables that it later uses to locate information and files Formatting also removes all Hidden System files as well Basically it cleans your SD memory card just like if it was brand new Please make sure to follow the guidelines listed below SD Card size 2Gb or below format using File System type FAT SD Card size 4GB or above format using File S
3. This will damage the unit and void the warranty Use a soft lens cloth for cleaning lens Avoid touching lens with fingers Remove dirt or stains with a soft cloth dampened with water or neutral detergent Keep your camera in a dry and cool dust free environment or container when it is NOT used Take the batteries out when camera is NOT to be used over an extended period of time Avoid dropping your camera on to a hard surface Do not disassemble your camera Do not mix new and old batteries Do not open the camera for unauthorized service This could cause serious damage to the unit and WILL void the warranty NOTE This camera is a precision electronic device Do not attempt to service this camera yourself as opening or removing covers may expose you to dangerous voltage points or other risks WWW STEALTHCAM COM Toll Free 877 269 8490 QUICK START GUIDE This guide is designed to get you up and running in a matter of moments To get the most out of this advanced scouting tools please read the manual thoroughly before operating the camera If you would like to modify any of the factory Default Settings except for the Time amp Date please see manual for instructions FACTORY DEFAULT SETTINGS Time Out 30 Sec Burst Mode 1 Still Image 1 3Mp Resolution Operation Mode P R Video Mode 10 Seconds VGA Resolution Time lapse setting 18 00 8 00 Next day CAMERA SETUP 1 Install 8 AA cell batter
4. i c Mode Start Time setting display will show TIME S 88 88 AW EF S Start 88 88 time in HH MM DO TIME e Press OK to set the Start Time 4 setting At this point you can adjust the 89 00 time from 00 00 to 23 59 555555 WWW STEALTHCAM COM 24 Toll Free 877 269 8490 e The MINUTE digits will be blinking e Press UP or DN to increase or decrease the minute value 00 59 e Press OK to save your selection and enter Hour setting e The HOUR digits will be blinking e Press UP or DN to increase or decrease the hour value 00 23 e Press OK to save the Start Time setting and move to the End Time setting e After completing the start time setting bel F camera will go into TLS Mode End Time CO setting e display will show TIME E 88 88 c 00 09 E End 88 88 time in HH MM e Atthis point you can adjust the time from 00 00 to 23 59 by pressing the UP DN OK buttons same as Start Time settings e Press OK to save the End Time settings and move directly to the TIME OUT setting e Please complete the TIME OUT Still image resolution Burst Mode Zoom settings like the settings on the PIR operation mode e Then press MENU button to exit EXAMPLE 1 If a user selected the Time Lapse mode and set the start time from 08 00 and end time at 20 30 and then selected the timeout to be WWW STEALTHCAM COM 25 Toll
5. next data Camera s front counter will reset to 0000 On the other hand when SD card is full camera s counter will then change the display to WWW STEALTHCAM COM 41 Toll Free 877 269 8490 read FULL Images and Videos under each folder will be named from 0001 up to 9999 SD Card Capacity and Compatibility Due to the rapidly changing memory card market please consult www stealthcam com for the most up to date information regarding memory cards MOON PHASE SYMBOL CHART Symbol__ Lunation from to D q 29 or 30 WWW STEALTHCAM COM 42 Toll Free 877 269 8490 FREQUENTLY ASKED QUESTIONS What does it mean when I have all 8 s on my LCD screen A This usually refers to an incompatible memory card or memory card damaged Make sure your card has been properly formatted Q Is the infrared flash invisible A The infrared flash will give off no glow whatsoever 15 my game camera Mac compatible A This camera model is not compatible with Mac computers Can I use rechargeable batteries in the camera A Rechargeable batteries are fine for the unit regular alkaline batteries designed for digital electronics are recommended for best performance Q When I use a memory card can I view the pictures on my personal digital camera A We do not recommend viewing memory card images taken in your game camera on any other digital camera you may experience compat
6. M pixels image Base image quality Default e Resolution for Video Color Daytime Black amp White Nighttime gt VGA 640x480 ONLY resolution e Time out To set the amount of time in seconds and minutes the camera will sleep between PIR triggering e Moon phase Displays the moon phases e Temp stamp Temperature stamp will display on still images and first frame only on video files e Zoom Digital enhancements different zoom level gt 1X Normal the word ZOOM will not display gt 2X Two times zoom the word ZOOM will display gt Four times zoom The word ZOOM will blink Battery Status Shows the battery status gt Full The battery is full gt Low The battery is low Front Low Battery indicator will also blink WWW STEALTHCAM COM 15 Toll Free 877 269 8490 NOTE When the camera detects low batteries the camera unit will power off within 30 seconds automatically Please replace with new batteries otherwise the camera may not work properly Setting the Camera s Operation Mode Your Stealth Cam can be programmed to operation either in PIR Detection mode or Time Lapse mode Switch the camera to the ON position gt LCD screen will display the camera status screen Press the MENU button once within 30 seconds to enter the programming mode the word PIR or tLS will be blinking CAMERA 8 Pin ELS Press the UP or D
7. N button to select the PIR or 5 Press OK to save your selection Press MENU button to exit WWW STEALTHCAM COM 16 Toll Free 877 269 8490 Setting the Camera s Resolution in PIR operation mode Your Stealth Cam can be programmed to 3 different resolutions High 3 Stars 8Mp Low 2 Stars 3Mp Base 1 Star 1 3Mp e Switch the camera to the ON position gt LCD screen will display the camera status screen e the MENU button once within 30 seconds to enter the programming mode e The word PIR will be blinking press OK to confirm the camera operation by PIR detection e The word CAMERA and the STARS will be blinking e Press the OK button ONCE to choose the selection e Press the UP or DN button to select the desired resolution e Press OK to save your selection Press MENU button to exit Setting the IR emitter selection This camera is equipped with an IR control toggle switch Make sure camera is in the OFF position before making any changes e 54IR fFull illumination Ideal for subject matter beyond 20ft e 36 IR Reduced illumination Good for use when subject is 20ft or closer WWW STEALTHCAM COM 17 Toll Free 877 269 8490 Setting the Capturing Sequence in PIR operation mode Your Stealth Cam can be programmed to shoot 1 9 pictures per triggering e Switch the camera to the ON position gt LCD screen will display the camera status screen e Press the MENU bu
8. STEALTH 0 INSTRUCTION MANUAL Model STC SNX1 Toll Free 1 877 269 8490 WWW STEALTHCAM COM Version 1 0 10 11 IMPORTANT NOTE First congratulations on purchasing one of the finest scouting cameras on the market today We appreciate your business and want to prove to you we are committed to providing you the best product and support in the field By giving our customers a new state of the art web interface which provides you with video tutorials and instruction on how to use the product in the most effective way TECHNICAL SUPPORT CUSTOMER SERVICE EMAIL stealthcam gsmorg com CONTACT amp HOURS Please allow 48hrs for response Toll Free 1 877 269 8490 Stealth Cam LLC Call Center Hours P O Box 539504 Mon Fri 8 AM 6 PM CST Grand Prairie TX 75053 9504 www stealthcam com Stealth Cam Limited Warranty Your Stealth Cam scouting camera is covered by a One Year Limited Warranty on parts and labor from the date of original purchase and purchases must be made through an authorized dealer The warranty covers defects in workmanship and materials The warranty does not apply to units which have been damaged or abused intentionally or unintentionally A purchase from individuals or unauthorized Internet sites such as eBay voids the warranty Tampering with or altering the unit will void the warranty Any unauthorized service will void warranty A copy of your original sales receipt must be produced
9. alth Cam Advanced Digital Scouting Camera is designed to operate using two different types of battery power options Batteries AA cell The internal battery compartment accepts 8 AA cell batteries Be sure to use high quality brand name alkaline batteries Install batteries with correct polarity as noted inside the battery compartment 12V Lead Acid external battery The camera is equipped with an external power jack designed to accept a barrel plug cable attached to a sealed lead acid battery Sold separately Battery cable and complete 12V Lead Acid battery kits are available wherever Stealth Cam scouting cameras are sold or call toll free 877 269 8490 Only Stealth Cam external battery accessories are recommended WWW STEALTHCAM COM 11 Toll Free 877 269 8490 e sure camera is in the OFF position e Insert the external battery barrel plug into the DC 12V jack on the bottom of camera housing e Turn the camera power on NOTE Please make sure the voltage and polarity are correct before connection Incorrect voltage or polarity will damage the camera When both internal and external batteries are connected the camera will draw power from the higher voltage source first Memory Options The camera is also equipped with an expandable media card slot capable of accepting up to 16GB SD card sold separately The front counter display will show the number of images stored on the SD card
10. and now you ll see tu N blinking ibm a er RESOLUTION HGH RESOLUTION HGH tuii tu P WWW STEALTHCAM COM 32 Toll Free 877 269 8490 Press the DN button to set the camera s TV OUT to PAL The word tu will now be blinking Press the OK to confirm this setting The word tu P will be blinking and then stops Once the blinking stops power off the camera Wait for 5 seconds and then power up your camera again Thumbnail Images You will see a series of thumbnail images on your monitor Press the UP or DN button to navigate though your thumbnail images On the upper left hand corner of your TV monitor it will either display the image icon or video icon to show you whether that image is a still image or video clip To view image in full screen press the OK button Press the OK button again it will return to the thumbnail view from the full size image WWW STEALTHCAM COM 33 Toll Free 877 269 8490 Viewing Video Clips on handheld LCD monitor or home TV monitor e Follow the cable attaching instruction listed in previous section e You will see a series of thumbnail images on your monitor e Press the UP or DN button to choose the video clip you want to watch e Press the OK button to play the video clip You may pause the video clip by pressing the OK button during the playback Press OK button to resume playing e At the end of the video c
11. crease or decrease the Month value 1 12 WWW STEALTHCAM COM 22 Toll Free 877 269 8490 e Press OK to save your selection and enter Day setting e The Day digits will be blinking e Press UP or DN to increase or decrease the Day value 01 31 e Press OK to confirm the Date setting and enter Year setting e The YEAR digits will be blinking e Press UP or DN to increase or decrease the Year value 01 99 e Once this is all done press You ll then see the word dEL blinking e Press MENU button to exit the program setting and back to the status screen WWW STEALTHCAM COM 23 Toll Free 877 269 8490 Setting the Time Lapse Mode The Time Lapse Default setting value is from 18 00 to 8 00 the next day When the camera is set to time lapse mode the program setting will bypass any PIR activation Instead the user can set the program for a pre determined time period such as 6 00 to 18 00 The user then sets the frequency of pictures only NOT videos during this time period such as one picture every 10 seconds The camera will remain in Time Lapse mode until the user has changed the program setting e Switch the camera to the ON position gt LCD screen will display the camera status screen e Press the MENU button once within 30 seconds to enter the programming mode CAMERA x e Press UP button until you see the xf word tLS blinking e Press OK to confirm and go into TLS
12. for any warranty service and a Return Authorization RA number must be obtained from customer service at 877 269 8490 prior to returning product WWW STEALTHCAM COM 2 Toll Free 877 269 8490 IMPORTANT NOTE TRIAD equipped cameras include FREE Image Scan Software download at www stealthcam net sc_image scan html Stealth Cam Image Scan provides sophisticated motion searches based on targeted zones within a selected series of time lapse images Additional features include e Watch days of video in minutes with variable speed playback e Import Time Lapse Photo sets from SD card to your computer e Open existing Time Lapse Photo sets on your computer e Process Photo Sets into high speed motion video e Quickly jog through the time lapse frames forwards and backwards e Step frame forwards and backwards e Create videos that you can watch email or upload To ensure optimum performance your Stealth Cam Wildview camera may be eligible for periodical free software updates Please check http stealthcam net sc_downloads_d html for the latest firmware downloads amp sign up for our weekly newsletter to stay informed on updates amp new product news WWW STEALTHCAM COM 3 Toll Free 877 269 8490 TABLE OF CONTENTS Camera overview Camera Kit contents General Information Quick Start Guide Battery and Memory Installation Setup and Programming Using the Camera Viewing amp Deleting Files Memory Compa
13. he file name gt save your images and videos Highlight the file or files you want to save and drag them to your hard drive gt To delete your images and videos Highlight the files or files you want to delete and press the DELETE button gt To erase all files and reformat you SD memory card Right click on the Removable Storage device under My Computer and select FORMAT then click START You will receive a Warning message press OK Then CLOSE to exit NOTE Make sure before you FORMAT you are certain it is the Removable Storage device for the camera e Once you re done simply unplug the cable from both your computer and the camera The camera will turn OFF automatically WWW STEALTHCAM COM 36 Toll Free 877 269 8490 Deleting files in the field e Switch the camera to the ON position gt LCD screen will display the camera status screen e the MENU button within 30 seconds to enter the programming mode showing either PIR or tLS e Press the UP or DN button to enter PIR mode then press OK e Press the DN button ONCE to enter the delete mode e You ll see the word dEL blinking e Press OK button to enter the DELETE amp FORMAT menu e Press UP or DN button to select the desired function gt NO dL No Delete No images get deleted gt d ONE Delete One Only the last file will get deleted gt d ALL Delete ALL Deletes ALL images on the SD card gt For
14. ibility issues Q Will I lose my images and setting when the batteries die A The images are stored on your external SD memory card so your images will be intact only on your card However you will need to reset your settings WWW STEALTHCAM COM 43 Toll Free 877 269 8490 What my options if my camera is past it warranty A We have an out of warranty program in which you may purchase a refurbished reconditioned replacement unit for 50 or more off based on retail price of unit discount exchange of your old unit Can 1 use my game camera through a window or glass door A Glass may disrupt your sensor beam we don t advise using the camera in this fashion Q Do I need to recharge 12V Battery Kit during the seasons it s not in use A The 12V Battery Kit should be recharge at least every 3 months regardless if it is being used or not in order to preserve the working condition of the battery inside the unit NOTE For the latest updates and information please check our website regularly WWW STEALTHCAM COM 44 Toll Free 877 269 8490 WARNING Modification not approved by the party responsible for compliance could void user s authority to operate FCC Compliance This equipment has been tested and found to comply with the limits for Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a
15. ies in correct polarity as indicated in battery compartment 2 Insert SD card into the camera 3 Turn power on to adjust Time and Date SET TIME AND DATE 1 Switch the camera to the ON position Press the MENU button to enter menu settings screen Press the UP or DN button until the word PIR blinking Press the OK button to confirm Press the UP or DN button to scroll through different setting modes until the word TIME blinking 6 Press the OK button to choose the Time settings 7 Press the UP or DN button to adjust the Minute setting and press OK to confirm and move to the Hour setting 8 Repeat to set Hour and then press OK to confirm and move to Date 9 Adjust the Month Day and Year by using UP or DN button Each time you finish an adjustment you must press the OK button to confirm and move to the next field for adjustment 10 Once done the word dEL will be blinking 11 Press the MENU button to exit and start using WWW STEALTHCAM COM 10 Toll Free 877 269 8490 BATTERY AND MEMORY INSTALLATION WARNING Do not use different Voltage lead acid battery other than the one specified in this section Doing so will damage the camera and will void the warranty WARNING ALWAYS have the camera in the OFF position when installing or removing batteries and memory card Removing batteries or memory card while the camera is ON may damage the camera Your Ste
16. ill be blinking Press OK button and the SECONDS digits will be blinking Press UP or DN button to increase or decrease the time value in seconds from 0 to 59 seconds in 1 second increments Press OK to save the seconds setting and the MINUTES digits will be blinking Press UP or DN button to increase or decrease the time value in minutes from to 59 minutes in 1 minute increments Press OK to save the minutes setting You ll then see the word TIME blinking Press MENU button to exit WWW STEALTHCAM COM 21 Toll Free 877 269 8490 Setting the Time and Date in PIR operation mode Your Stealth Cam uses the 24hr military time format Switch the camera to the ON position gt LCD screen will display the camera status screen Press the MENU button within 30 seconds to enter the programming mode The word PIR will be blinking press OK to confirm the camera operation by PIR detection Press DOWN button TWO times to enter Time and Date mode The word TIME will be blinking Press OK to enter Minute setting first The MINUTE digits will be blinking Press UP or DN to increase or decrease the minute value 00 59 Press OK to save your selection and enter Hour setting The HOUR digits will be blinking Press UP or DN to increase or decrease the hour value 00 23 Press OK to save your selection and enter Month setting The Month digits will be blinking Press UP or DN to in
17. ink gt Press the UP button ONE time to toggle to Camera mode gt Press the OK button TWO times gt Press the MENU button once to exit WWW STEALTHCAM COM 29 Toll Free 877 269 8490 e 30 seconds after you ve made your adjustments the camera s green LED light will begin blinking and enter count down mode This is your indication to leave the coverage area within one minute e After one minute the camera will enter either image burst mode or adjustable video mode based on your program setting The camera will then time out between 0 59 seconds or 0 59 minutes depending on your program setting NOTE The time between motion detection and the camera taking the pictures may vary due to lighting conditions program settings and battery power level The IR Emitter will only activate in low light conditions WWW STEALTHCAM COM 30 Toll Free 877 269 8490 VIEWING AND DELETING FILES The STC SNX1 cam offers the user different options for viewing their images You can view images or videos through either a handheld LCD monitor or your home TV that is equipped with and RCA Input jack The external LCD display on the front of the housing will show the number of images in memory NOTE The instructions below are based on starting with a camera that s power is turned off For viewing on handheld LCD monitor e Attach the appropriate cable to the TV port on the side of the camera e Insert the other e
18. lip press the UP or DN button to proceed to the next video or image If it is a video clip file then it will automatically start to play If it is still image file then it will show the image in full screen When you view still images in full screen you can return to thumbnail image selection view by pressing the OK button NOTE All videos are recorded with audio but only has sound when viewing playback on a PC WWW STEALTHCAM COM 34 Toll Free 877 269 8490 Viewing files by computer Your Stealth Cam Digital Scouting Camera is a plug and play USB storage device for users of Windows 2000 ME Vista Windows 7 operating systems This camera is not MAC compatible PC with USB Port Viewing files on your computer via USB connection Make sure the camera s power switch is in the OFF position Plug the larger end of the USB cable into an available USB port on your computer Plug the smaller end of USB cable into the camera s side panel The camera will automatically power ON and display the word USb on the display screen ch At the same time your computer will recognize the camera as a Removable Storage device You will find it under MY COMPUTER WWW STEALTHCAM COM 35 Toll Free 877 269 8490 e Atthis point you have several options gt To view your images or play your videos Click on the Removable Storage device and then drill down to the file you want to see and double click on t
19. mat Deletes all files reformats the SD card CAMERA CAMERA py CAMERA piy CAMERA kk D RA kk Ft e Press OK to confirm your selection e Press MENU button to exit the program setting and back to the status screen WWW STEALTHCAM COM 37 Toll Free 877 269 8490 MEMORY COMPATIBILITY CHART The following cards have been tested and approved for use with the STC SNX1 model PNY 166 NOTE Proper camera operation cannot be guaranteed when using memory cards NOT listed above WWW STEALTHCAM COM Toll Free 877 269 8490 38 TECHNICAL SPECIFICATIONS System Requirements and Compatibility e Windows Me 2000 XP Vista Windows 7 e Pentium 4 2GHz or above e 1GB RAM 2GB recommended e 32 bits color Resolution 800x600 or above w 256MB e 2GB free hard disc space e An available USB 1 1 port USB 2 0 recommended e DirectX 9 0 or above Should come with your operating system already e Optional Windows compatible sound card and speaker NOTE If you have any questions regarding your PC specifications please contact your PC manufacturer WWW STEALTHCAM COM 39 Toll Free 877 269 8490 Camera Features and Specification High precision multi layer glass lens with coating Built in 1 85 B amp W LCD display External memory support SD memory card up to 16GB Resolution Options 8 0M 3 0M 1 3M Image interpolated from 5M Sensor Ca
20. nd into the VIDEO IN jack on the handheld LCD video monitor Turn on both the camera and the monitor e You will see a series of thumbnail images on your monitor e Press the UP or DN button to navigate though your thumbnail images Onthe upper left hand corner of your TV monitor it will either display the image OR the image with a video icon which indicates it s a video clip To view in full screen press the OK button e Press the OK button again it will return to the thumbnail view from the full screen image WWW STEALTHCAM COM 31 Toll Free 877 269 8490 For viewing on your home TV monitor Attach the appropriate cable to the TV port on the side of the camera Insert the other end into the RCA VIDEO IN jacks on the TV Turn on both the camera and the TV monitor Make sure to switch to AUX VIDEO IN mode on your TV gt See your TV owner s manual for directions The camera s TV OUT is set to NTSC by default NTSC Standard North American TV format gt Ifthe TV monitor doesn t flicker then you do not need to change your camera s TV OUT setting Proceed to the next section called Thumbnail Images gt Ifthe TV monitor does flicker then you will need to proceed to the next step to change your camera s TV OUT from NTSC to PAL Standard European TV format Press the MENU button once The word tu on the camera s internal screen will be blinking Press the OK once
21. nds to sense motion heat and take a picture Clear out any brush or weeds in front of camera This will cause false pictures caused wind or high temperature days Double check battery before turning on the camera for use Make sure to insert the memory card after setting up the game camera Make sure to turn the camera ON or take out of Test Mode before you leave Verify time and date is correct WWW STEALTHCAM COM 27 Toll Free 877 269 8490 Example Mounting EFFECTIVE DISTANCE 30 FEET HORIZONTAL Example Trail Setup Incorrect 8 Trail Correct 16 feet Trail WWW STEALTHCAM COM Toll Free 877 269 8490 28 Using the camera in PIR detection mode e Mount the camera to the tree or other sturdy object using either a tree screw optional accessory or supplied mounting strap e Open the front housing and move the switch to the ON position At this point you have 30 seconds to start making any program changes To Capture Videos make sure display reads VIDEO e If display does not read VIDEO then gt gt gt gt gt Press the MENU button once The word CAMERA will blink Press the UP button TWO times to toggle to Video mode Press the OK button TWO times Press the MENU button once to exit To Capture Images make sure display reads CAMERA e If display does not read CAMERA then gt Press the MENU button once gt The word CAMERA will bl
22. our Stealth Cam can be programmed to have 3 different zoom levels Switch the camera to the ON position gt LCD screen will display the camera status screen Press the MENU button once within 30 seconds to enter the programming mode The word PIR will be blinking press OK to confirm the camera operation by PIR detection Press UP button THREE times to enter Zoom setting mode The word ZOOM will be blinking Press OK button and the zoom level number will now blink Press the UP or DN button to select the desired zoom level setting 1 1X Normal 2 2X Zoom 4 4X Zoom Press OK to confirm your selection Press MENU button to exit NOTE The use of the digital zoom feature may degrade image amp video quality as this tells the camera to focus on a specific are of the image and increase its size This will cause dithering of the image WWW STEALTHCAM COM 20 Toll Free 877 269 8490 Setting the Time Out Mode in PIR operation mode Your Stealth Cam can be programmed to set the amount of time in seconds or minutes the camera will sleep between PIR triggers Switch the camera to the ON position gt LCD screen will display the camera status screen Press the MENU button once within 30 seconds to enter the programming mode The word PIR will be blinking press OK to confirm the camera operation by PIR detection Press UP button FOUR times to enter Time Out setting mode The word TIME OUT w
23. pturing Options 1 9 image burst mode or video recording with audio Image format Standard JPEG Auto white balance and auto expose Auto IR emitter light control gt Effective Range for Still picture up to 50 ft gt Effective Range for Video clip up to 50 ft Real time clock for date and time stamping 4 digits LCD Image counter Green TEST LED indicator Focusing 5 ft to infinity Effective viewing angle 50 degrees PIR detection angle 48 degrees Interface type USB 1 1 Power AA size alkaline or lithium batteries x 8 External power 12 volts battery pack WWW STEALTHCAM COM 40 Toll Free 877 269 8490 IMAGE CAPACITY CHART STC SNX1 Data Day Res Pixels size Resolution 1G 2G 4G 8G 16G 3264 x 2448 204 408 816 2048 x 1536 512 1 024 2 048 Base 1280 1024 1 024 2 048 4 096 AVI VGA 30 s 640 x 480 30 s 14 28 56 Data Night Res size Resolution 1G Hi 3264 2448 Lo 2048 1536 1280 1024 AVI VGA 30 s 640 x 480 30 s Subject to card compatibility under different brands NOTE Image Capacity Chart provides approximate number of images or AVI movies based on resolution settings and the size of the memory card These figures may vary depending on the amount of detail in the image When the SD card is NOT FULL but camera s front counter already reaches 9999 the camera will create a new folder to save the
24. residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio or television receptions which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measure gt Reorient or relocate the receiving antenna gt Increase the separation between the equipment and the receiver gt Connect the equipment into an outlet on a circuit different from that to which the receiver is connected gt Consult the dealer or an experienced radio TV technician for help Product specifications are subject to change Stealth Cam is not responsible for any photographic or typographical errors May be protected by one or more U S Patent numbers 6 735 387 6 768 868 6 834 162 7 149 422 7 308 196 7 593 632 7 710 457 7 873 266 WWW STEALTHCAM COM 45 Toll Free 877 269 8490
25. tibility chart Technical Specifications Image Capacity chart Moon Phase chart Frequently Asked Questions FAQs FCC Compliance WWW STEALTHCAM COM Toll Free 877 269 8490 10 11 14 27 31 38 39 41 42 43 45 CAMERA OVERVIEW Front View Infrared LEDs Camera Lens Microphone Lock Slot Passive Infrared Sensor PIR Latch LCD Counter WWW STEALTHCAM COM Toll Free 877 269 8490 Inside View Test Mode IR Control Confirm Button LCD Screen Menu Button Power Switch Up Arrow Down Arrow Battery Compartment WWW STEALTHCAM COM 6 Toll Free 877 269 8490 Side amp Bottom view SD Card Slot USB Port TV Port Tree Screw Mount 12V DC Port For use with Stealth Cam Cable and or 12V Battery Box sold separately WWW STEALTHCAM COM 7 Toll Free 877 269 8490 CAMERA KIT CONTENT e Model STC SNX1 Digital Scouting Camera e User manual e Strap WWW STEALTHCAM COM Toll Free 877 269 8490 GENERAL INFORMATION Storing conditions Operating Environment 14 to 104 deg F 10 to 40 deg C 20 85 relative humidity non condensing Special care instructions The camera is designed to be weather resistant Never attempt to immerse the unit in water or any other liquid
26. tton once within 30 seconds to enter the programming mode e The word PIR will be blinking press OK to confirm the camera operation by PIR detection e Press the UP button ONE time to enter the Capturing Sequence setting mode e The word CAMERA will be blinking e Press OK button and the current number of burst mode images will blink e Press the UP or DN button to select the desired burst mode setting or number of pictures per triggering e Press OK to save your selection e Press MENU button to exit WWW STEALTHCAM COM 18 Toll Free 877 269 8490 Setting the Video in PIR operation mode Your Stealth Cam can be programmed to record 5 240 seconds of video per triggering The Video mode is only workable under PIR mode Switch the camera to the ON position gt LCD screen will display the camera status screen Press the MENU button once within 30 seconds to enter the programming mode The word PIR will be blinking press OK to confirm the camera operation by PIR detection Press UP button TWO times to enter Video setting mode The word VIDEO will be blinking Press OK button and the video length in seconds will be blinking Press UP or DN button to select the desired video length from 5 to 240 seconds in 5 second increments Press OK to save your selection Press MENU button to exit WWW STEALTHCAM COM 19 Toll Free 877 269 8490 Set the Digital Zoom in PIR operation mode Y
27. ystem type FAT32 Do not use File System type NTFS or exFAT these formats are not supported WWW STEALTHCAM COM 13 Toll Free 877 269 8490 SETUP AND PROGRAMMING When the camera is first turned on the internal LCD screen displays the camera status The following information is present on this screen PIR MODE TIME LAPSE MODE CAMERA CAMERA x xf xf ELS If no buttons are pressed after 30 seconds the LCD screen will power down to conserve battery life and enter 1 minute count down to enter PIR detection mode To re power the display screen press and hold the UP or DOWN button until you see the status screen Definition Day and Time Displays the date and time that you have set Operation mode gt Camera takes Image Video per PIR trigger gt Time Lapse tLS Camera takes the still image per preset time Capturing Sequence mode gt 1P 9P 1to 9 burst mode image capturing per PIR trigger gt Video 5 240 seconds adjustable video per PIR trigger e Resolution for Images Color Daytime Black amp White Nighttime gt 3 Stars 8Mp Select this option to capture a 8 0 pixels image High image quality xx High image quality interpolated from 5M sensor WWW STEALTHCAM COM 14 Toll Free 877 269 8490 gt 2Stars 3Mp Select this option to capture 3 0M pixels image Low image quality xx gt 1Star 1 3Mp Select this option to capture a 1 3
Download Pdf Manuals
Related Search